Panasonic KX-TG8220FX User manual

PQQW15784ZA DC0707PS0 FX-2
This unit is designed to be used in Czech, Slovakia, and central Europe. To use this unit
in your country, first change the unit’s region setting to match your country. Change the
unit’s display language as needed. Refer to “Changing the unit’s region setting” in the
operating instructions.
Routine care
LTo clean the product, use a dry soft cloth. The outer surface of the product can
be scratched by wiping or rubbing with a hard cloth.
Connections
Important:
LIf you use a telephone line cord which is not supplied, the unit may not work
properly.
To telephone line
USE ONLY the supplied cord.
USE ONLY the supplied AC adaptor.
“Click”
(220–240 V, 50 Hz)
Hooks
Base unit Press plug firmly.
(220–240 V, 50 Hz)
USE ONLY the supplied AC adaptor (smaller).
Hooks
Press plug firmly.
(KX-TG8202)
Charger
Digital Cordless Phone
Model No. KX-TG8200FX/KX-TG8202FX
Digital Cordless Answering System
Model No. KX-TG8220FX
Quick Guide
TG8200_8220FX(e-e)_QG.fm Page 1 Monday, July 9, 2007 7:18 PM

– 2 –
Battery installation/Battery charge
Initial charge: 7 hours
Note:
LUSE ONLY rechargeable Ni-MH batteries.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.
Screen saver mode
The backlight will turn off completely after 1 minute
of inactivity if the handset is not on the base unit or
charger.
Press {ih} to turn the display on again.
Base unit *1 Charger *2
*1 The pictured model is KX-TG8200.
*2 KX-TG8202
Rechargeable
Ni-MH ONLY
“Charging” will
be displayed.
{ih}
TG8200_8220FX(e-e)_QG.fm Page 2 Monday, July 9, 2007 7:18 PM

– 3 –
Operating tips
Using the joystick
Push the joystick up, down, left, or right to navigate
through menus and to select.
Note:
LWhen selecting menu or the desired item, these
operating instructions use the following indication.
Example: {^}/{V}: “Off”
Push the joystick up or down to select the words in
quotations.
Adjusting the receiver or speaker
volume
Push the joystick up or down while on a call.
Soft keys
The handset features 2 soft keys and a joystick. By
pressing a soft key, or by pressing the centre of the
joystick, you can select the feature shown directly
above it on the display.
Menu icons
When in standby mode, pressing down on the centre of the joystick reveals the
handset’s main menu. From here you can access various features and settings.
*1 KX-TG8200/KX-TG8202
*2 KX-TG8220
Volume up
Volume down
jCaller List
XSMS (Short Message Service)
KTime Settings*1
IAnswer System*2
NHandset Setup
|Base Unit Setup
MDisplay Setup
TG8200_8220FX(e-e)_QG.fm Page 3 Monday, July 9, 2007 7:18 PM

– 4 –
Display language
16 display languages are available.
1{ih} i"
2Select Nby pushing the joystick in any direction. i#
3Push the joystick up or down to select “Display Setup”. i#
4Push the joystick up or down to select “Select Language”. i#
5Push the joystick up or down to select the desired language. i#i{ih}
Dialling mode (tone/pulse)
1"(centre of joystick)
2Select |by pushing the joystick in any direction. i#
3Push the joystick up or down to select “Call Options”. i#
4Push the joystick up or down to select “Dial Mode”. i#
5Push the joystick up or down to select the desired setting. i#i{ih}
Date and time
1"(centre of joystick)
2Select Nby pushing the joystick in any direction. i#
3Push the joystick up or down to select “Time Settings”. i#
4Push the joystick up or down to select “Set Date & Time”. i#
5Enter the current date, month, and year.
6Enter the current hour and minute.
7#i{ih}
You can select
You can select
“Deutsch
Deutsch
”,
,
“English
English
”,“Magyar
Magyar
”,
,
“Polski
Polski
”,“SlovenČina”,
“ČeŠtina
tina
”,
,
“Hrvatski
Hrvatski
”,
,
“Slovenscina
Slovenscina
”,
,
“Eesti
Eesti
”,“LIETUVI
LIETUVI
ŠKAI
KAI
”,
,
“Latvie
Latvie
Šu”,
,
“Rom
Rom
ânã”,
,
“БЪЛГАРСКИ”,
,
“Srpski
Srpski
”,
,
“МАКЕДОНСКИ”, or
, or
“Shqip
Shqip
”.
TG8200_8220FX(e-e)_QG.fm Page 4 Monday, July 9, 2007 7:18 PM

– 5 –
Basic operations
CMaking/Answering calls (Handset)
Making calls Dial the phone number. i{C}/{s}
Answering calls {C}/{s}
Hanging up {ih}
Receiver/speaker volume Push the joystick up or down while on a call.
Making a call using the redial
list
j(right soft key) i{^}/{V}: Select the desired
number. i{C}/{s}
Temporary tone dialling
(for rotary/pulse service
users)
1Make a call.
2Press {*} when prompted to enter your code or
PIN, then press the appropriate dial keys.
Handset ringer volume 1"(centre of joystick) iNi#
2{^}/{V}: “Ringer Setup”i#
3{^}/{V}: “Ringer Volume”i#
4{^}/{V}: Select the desired volume. i#i
{ih}
kPhonebook (Handset)
Adding entries (names and
phone numbers)
1n(left soft key) i"
2{^}/{V}: “New Entry”i#
3Enter the party’s name (16 characters max.). i
#
4Enter the party’s phone number (24 digits max.).
i#
5{^}/{V}: Select the desired category. i#
6{^}/{V}: “Save”i#i{ih}
LTo enter a name, see the character table in the
operating instructions.
Making calls 1n(left soft key)
2{^}/{V}: Select the desired entry. i{C}
IAnswering system (Base unit): KX-TG8220
Answering on/off Press {s}to turn on/off the answering system.
Listening to messages {6}
TG8200_8220FX(e-e)_QG.fm Page 5 Monday, July 9, 2007 7:18 PM

– 6 –
Frequently asked questions
Question Cause & solution
Why is wflashing? LThe handset is too far from the base unit. Move
closer.
LThe base unit AC adaptor is not connected.
Check the connections.
LYou are using the handset or base unit in an area
with high electrical interference. Place the
handset and base unit away from interference
sources, such as antennas and mobile phones.
LThe handset is not registered to the base unit.
Register it (page 8).
Why can I not make calls? LThe dialling mode setting is incorrect. Set to
“Tone”or “Pulse”as needed.
Why is the handset display
blank?
LThe handset is in screen saver mode. Press
{ih} to activate the handset display again.
What should I do when the
handset does not turn on?
LMake sure that the batteries are installed
correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
How long is the battery
operating time?
LWhen you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 12 hours max.
In continuous standby mode: 150 hours max.
LIt is normal for batteries not to reach full capacity
at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).
LActual battery performance depends on a
combination of how often the handset is in use
and how often it is not in use (standby).
TG8200_8220FX(e-e)_QG.fm Page 6 Monday, July 9, 2007 7:18 PM

– 7 –
Can I keep the handset on
the base unit or charger
when I am not using it?
LEven after the handset is fully charged, the
handset can be left on the base unit or charger
without any ill effect on the batteries.
When should I replace the
batteries?
LIf the batteries are fully charged until & is
displayed, but
) is displayed after a few calls,
replace the batteries with new ones.
What is a PIN? LThe PIN is a 4-digit number that must be entered
in order to change certain base unit settings. The
default PIN is “0000”.
What do I need to do to
display caller information?
LYou need to subscribe to Caller ID service.
Consult your service provider/telephone company
for details.
LThe message “You must first subscribe
to Caller ID.” will be displayed until you
receive caller information after subscribing to
Caller ID service.
What should I do when:
– I hear static or sound cuts
in and out?
– there is interference from
other electrical units?
LPlace the handset and the base unit away from
other electrical appliances.
LMove closer to the base unit.
LYour unit is connected to a telephone line with
DSL service. We recommend connecting a filter
(contact your DSL service provider) to the
telephone line between the base unit and the
telephone line jack.
What should I do when the
operating time seems to be
short even after I fully
charged the batteries?
LWipe the battery ends (S, T) and the unit
contacts with a dry cloth.
What do I need to do to
erase W(Missed call) from
the display?
LThere are unviewed missed calls remaining. View
them using the following method.
1"(centre of joystick) iji#
2Push the joystick down to search from the most
recent call, or push the joystick up to search
from the oldest call.
Frequently asked questions
Question Cause & solution
TG8200_8220FX(e-e)_QG.fm Page 7 Monday, July 9, 2007 7:18 PM

– 8 –
Registering a handset to a base unit
The supplied handset and base unit are pre-registered. When you purchase an
additional handset, refer to the additional handset’s installation manual for
registration. If for some reason the handset is not registered to the base unit, register
the handset.
1"(centre of joystick) iNi#
2{^}/{V}: “Registration”i#
3{^}/{V}: “Register H.set”i#
4{^}/{V}: Select a base unit number. i#
5Proceed with the operation for your model.
NKX-TG8200/KX-TG8202
Press and hold {x} on the base unit for
about 5 seconds. (No registration tone)
NKX-TG8220
Press and hold {x} on the base unit for
about 5 seconds, until the registration tone
sounds.
6Wait until “Enter Base PIN”is displayed.
iEnter the base unit PIN (default: “0000”).
i#
#
{x}
{x}
#
TG8200_8220FX(e-e)_QG.fm Page 8 Monday, July 9, 2007 7:18 PM

– 9 –
Optional service (Caller ID and SMS)
If you subscribe to Caller ID service, you can:
– display caller information
– identify who is calling by using different display colours and
ringtones (handset phonebook category)
To use SMS, you must subscribe to Caller ID and/or appropriate service.
– SMS (Short Message Service)
012345
012345
TG8200_8220FX(e-e)_QG.fm Page 9 Monday, July 9, 2007 7:18 PM

– 10 –
TG8200_8220FX(e-e)_QG.fm Page 10 Monday, July 9, 2007 7:18 PM