Panasonic AW-UE80WP User manual

DVQP2625ZA
W0222GU0 -FJ
ENGLISH
Model No. AW‑UE80WP
Model No. AW‑UE80KP
Model No. AW‑UE80WE
Model No. AW‑UE80KE
Model No. AW‑UE80WED
Model No. AW‑UE80KED
Operating Instructions
4K Integrated Camera
Before operating this product, please read the instructions carefully and save this manual for future use.
Please carefully read the “Read this first!” (pages 2 to 5) of this Manual before use.
PJ EJ ED

Read this first! (For AW‑UE80WP, AW‑UE80KP)
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws, drop-prevention wire mounting screw and pan stopper
out of the reach of infants and small children.
WARNING:
Installation should only be performed by qualified installation
personnel.
Improper installation may result in the entire apparatus falling
down and causing injury.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
This apparatus can be operated at a voltage in the range of 100
– 240 V AC.
Voltages other than 120 V are not intended for U.S.A. and
Canada.
Operation at a voltage other than 120 V AC may require the use
of a different AC plug. Please contact either a local or foreign
Panasonic authorized service center for assistance in selecting
an alternate AC plug.
CAUTION:
The mains plug of the power supply cord shall remain readily
operable.
The AC receptacle (mains socket outlet) shall be installed near
the equipment and shall be easily accessible. To completely
disconnect this equipment from the AC mains, disconnect the
power cord plug from the AC receptacle.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
CAUTION:
To reduce the risk of fire or electric shock caused by damage to
the power supply cord, do not squeeze, bend, or pull the power
supply cord when using the apparatus.
indicates safety information.
2

FCC NOTICE (USA)
Supplier’s Declaration of Conformity
Model Number: AW-UE80WP/AW-UE80KP
Trade Name: Panasonic
Responsible Party: Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102
Support contact: 1-800-524-1448
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC Note:
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Warning:
To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to external units. Also,
any unauthorized changes or modifications to this equipment could void the user’s authority to operate it.
indicates safety information.
NOTIFICATION (Canada)
CAN ICES-3 (A)/NMB-3(A)
The symbols on this product (including the accessories) represent the following:
AC
DC
2 3
Read this first! (For AW‑UE80WP, AW‑UE80KP) (continued)

Read this first! (For AW‑UE80WE, AW‑UE80KE, AW‑UE80WED, AW‑UE80KED)
WARNING:
• To reduce the risk of fire or electric shock, do not expose this
equipment to rain or moisture.
• To reduce the risk of fire or electric shock, keep this equipment
away from all liquids. Use and store only in locations which are
not exposed to the risk of dripping or splashing liquids, and do
not place any liquid containers on top of the equipment.
WARNING:
Always keep the main unit mounting screw, bracket mounting
screws, drop-prevention wire mounting screw and pan stopper
out of the reach of infants and small children.
WARNING:
This equipment is compliment with Class A of CISPR 32.
In a residential environment this equipment may cause radio
interference.
WARNING:
Installation should only be performed by qualified installation
personnel.
Improper installation may result in the entire apparatus falling
down and causing injury.
CAUTION:
Do not remove panel covers by unscrewing.
To reduce the risk of electric shock, do not remove the covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION:
The mains plug of the power supply cord shall remain readily
operable.
The AC receptacle (mains socket outlet) shall be installed near
the equipment and shall be easily accessible. To completely
disconnect this equipment from the AC mains, disconnect the
power cord plug from the AC receptacle.
CAUTION:
In order to maintain adequate ventilation, do not install or place
this unit in a bookcase, built-in cabinet or any other confined
space. To prevent risk of electric shock or fire hazard due to
overheating, ensure that curtains and any other materials do not
obstruct the ventilation.
CAUTION:
To reduce the risk of fire or electric shock and annoying
interference, use the recommended accessories only.
CAUTION:
Check the installation at least once a year.
An improper installation could cause the unit to fall off resulting
in personal injury.
indicates safety information.
Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. and the other one is only for U.K.
Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.
FOR U.K. ONLY
If the plug supplied is not suitable for your socket outlet, it should be
cut off and appropriate one fitted.
FOR U.K. ONLY
This appliance is supplied with a moulded three pin mains plug for
your safety and convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amps and that it is approved by
ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure that it
is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used
until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
How to replace the fuse
1. Open the fuse compartment with a screwdriver.
Or
2. Replace the fuse.
Or Fuse
Fuse
indicates safety information.
The symbols on this product (including the accessories) represent the following:
AC
DC
4

Read this first! (For AW‑UE80WE, AW‑UE80KE)
EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Pre‑requisite conditions to achieving compliance with the above standards
<1> Peripheral equipment to be connected to the apparatus and special connecting cables
• The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment to be connected to the
apparatus.
• The purchaser/user is urged to use only the connecting cables described below.
<2> For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.
• Video signal connecting cables
Use double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications, for SDI (Serial Digital Interface).
Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended for analog video signals.
• Audio signal connecting cables
If your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.
Use shielded cables, which provide quality performance for high-frequency transmission applications, for analog audio signals.
• Other connecting cables (IEEE1394, USB)
Use double shielded cables, which provide quality performance for high-frequency applications, as connecting cables.
• When connecting to the DVI signal terminal, use a cable with a ferrite core.
• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this manual.
2. Performance level
The performance level of the apparatus is equivalent to or better than the performance level required by these standards.
However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an area where strong
electromagnetic fields are generated (by the presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverse
effects of the interference on the apparatus in cases like this, it is recommended that the following steps be taken with the apparatus being
affected and with its operating environment:
1. Place the apparatus at a distance from the source of the interference.
2. Change the direction of the apparatus.
3. Change the connection method used for the apparatus.
4. Connect the apparatus to another power outlet where the power is not shared by any other appliances.
Turkey Only
AEEE Yönetmeliğine Uygundur.
AEEE Complies with Directive of Turkey.
Disposal of Old Equipment
Only for European Union and countries with recycling systems
This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not
be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your
national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and
the environment. For more information about collection and recycling, please contact your local municipality, dealer or supplier.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
Manufactured by: Panasonic Corporation,Osaka, Japan
Importer’s name and address of pursuant to EU rules:
Panasonic Marketing Europe GmbH
Panasonic Testing Centre
Winsbergring 15, 22525 Hamburg, Germany
Інформація для покупця
Виробник: Panasonic Corporation Панасонік Корпорейшн
Адреса виробника: Kadoma, Osaka, Japan Кадома, Осака, Японія
Країна походження: China Китай
Імпортер: ТОВ "ПАНАСОНІК УКРАЇНА ЛТД"
Адреса імпортера: вул. Васильківська, буд. 30, м. Київ
03022, Україна
Примітки:
Термін служби виробу 7 років
Дата виготовлення може бути визначена за допомогою комбінації літер та цифр серійного номера, розташованого на продукті.
Приклад: X X XXXXXXX
Рік: остання цифра року (7 – 2017, 8 – 2018,…0 – 2020)
Місяць: А – Січень, В – Лютий… L – Грудень
4 5

Read this first!
Note on grounding
• Ground the unit via the <SIGNAL GND> ground connector.
Ground connector
to ground
connector on wall
outlet, ground bar,
etc.
 Trademarks and registered trademarks
• Microsoft®, Windows®, Windows®10, Microsoft Edge, Internet
Explorer®, ActiveX®and DirectX®are either registered trademarks
or trademarks of Microsoft Corporation in the United States and
other countries.
• Apple, Mac, macOS, iPadOS, iPhone, iPad, and Safari are
registered trademarks of Apple Inc., in the United States and other
countries.
• Android™ and Chrome™ browser are trademarks of Google LLC.
• Intel®and Intel®Core™ are trademarks or registered trademarks
of Intel Corporation in the United States and other countries.
• Adobe®and Reader®are either registered trademarks or
trademarks of Adobe Systems Incorporated in the United States
and/or other countries.
• The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other
countries.
• NDI is a registered trademark of NewTek, Inc. in the United
States.
• Other names of companies and products contained in these
Operating Instructions may be trademarks or registered
trademarks of their respective owners.
 About copyright and licence
It is expressly prohibited to distribute, copy, disassemble, reverse
compile, modify, reverse engineer, or export in violation of export
laws the software provided with the unit.
 Abbreviations
The following abbreviations are used in this manual.
• Windows®Internet Explorer®11 32/64-bit is abbreviated to
“Internet Explorer”.
For the purposes of this manual, the model numbers of the units are
given as listed in the table below.
Model number of unit Model number given in
manual
AW-UE80WP, AW-UE80KP,
AW-UE80WE, AW-UE80KE,
AW-UE80WED, AW-UE80KED
AW‑UE80
AW-RP150G AW‑RP150
AW-RP60G AW‑RP60
AV-HLC100P, AV-HLC100E AV‑HLC100
AV-UHS500P, AV-UHS500E AV‑UHS500
 Illustrations and screen displays featured
in the manual
• What is shown in the manual’s illustrations and screen displays
may differ from how it is actually appears.
• Functions which can be used by Windows Internet Explorer 11
only are indicated using the mark.
• The screenshots are used in accordance with the guidelines of
Microsoft Corporation.
6

Contents
Read this first! (For AW‑UE80WP, AW‑UE80KP)................................ 2
Read this first! (For AW‑UE80WE, AW‑UE80KE, AW‑UE80WED,
AW‑UE80KED) ................................................................................... 4
Read this first! (For AW‑UE80WE, AW‑UE80KE)................................ 5
Read this first! ...................................................................................... 6
Note on grounding ............................................................................... 6
Before use.............................................................................................. 8
Overview.............................................................................................. 8
Computer requirements ....................................................................... 8
Disclaimer of warranty ......................................................................... 9
Network security .................................................................................. 9
Features................................................................................................ 10
Accessories ......................................................................................... 11
Optional accessories .......................................................................... 11
Operating precautions ........................................................................ 12
Wireless remote control (optional accessory).................................. 15
Parts and their functions .................................................................... 16
Camera unit ....................................................................................... 16
Wireless remote control: AW-RM50AG (optional accessory) ............ 24
Setting the remote control IDs ........................................................... 26
Network settings.................................................................................. 27
Using Easy IP Setup Software to make settings for the unit.............. 27
Using EasyIP Setup Tool Plus to make settings for the unit.............. 27
Setting the initial account................................................................... 28
Installing the plug-in viewer software................................................. 29
Basic shooting operations ................................................................. 30
How to turn the power on and off ...................................................... 31
Turning the power on......................................................................... 31
Turning the power off......................................................................... 31
Selecting the units............................................................................... 32
Selecting the shooting modes (scene files)...................................... 33
Types of shooting modes................................................................... 33
How to select the shooting mode....................................................... 33
Shooting............................................................................................... 35
What to do when encountering problems in the basic shooting
operations ........................................................................................ 36
More advanced operations................................................................. 37
Manual shooting.................................................................................. 38
Manually adjusting the focus.............................................................. 38
Manually adjusting the iris.................................................................. 38
Manually adjusting the shutter speed ................................................ 38
Manually adjusting the gain ............................................................... 38
Preset memories.................................................................................. 39
White balance adjustment .................................................................. 40
Automatic adjustment (AWB: AWB A or AWB B) .............................. 40
Auto tracking white adjustment (ATW)............................................... 41
3200K and 5600K presets ................................................................. 41
VAR.................................................................................................... 41
Black balance adjustment .................................................................. 42
Automatic adjustment ........................................................................ 42
Black level (master pedestal) adjustment......................................... 43
Genlock adjustment ............................................................................ 44
Horizontal phase adjustment ............................................................. 44
Basic setup operations....................................................................... 45
When performing the operations using the wireless remote control.. 45
Camera menu items ............................................................................ 46
Setting the camera menu items ......................................................... 46
Top Menu screen............................................................................... 46
Camera screen .................................................................................. 47
Brightness 1/3 screen ........................................................................ 47
Brightness 2/3 screen ........................................................................ 48
Brightness 3/3 screen ........................................................................ 49
Picture 1/3 screen.............................................................................. 50
Picture 2/3 screen.............................................................................. 51
Picture 3/3 screen.............................................................................. 51
Matrix 1/5 screen ............................................................................... 52
Matrix 2/5 screen ............................................................................... 53
Matrix 3/5 screen ............................................................................... 53
Matrix 4/5 screen ............................................................................... 54
Matrix 5/5 screen ............................................................................... 54
Lens screen ....................................................................................... 55
System 1/2 screen ............................................................................. 56
System 2/2 screen ............................................................................. 57
Output 1/5 screen .............................................................................. 60
Output 2/5 screen .............................................................................. 61
Output 3/5 screen .............................................................................. 62
Output 4/5 screen .............................................................................. 62
Output 5/5 screen .............................................................................. 63
Pan/Tilt screen................................................................................... 63
P/T Acceleration screen..................................................................... 64
Preset 1/2 screen............................................................................... 66
Preset 2/2 screen............................................................................... 67
Preset Acceleration screen................................................................ 67
Maintenance screen........................................................................... 70
Firmware Version 1/2 screen............................................................. 70
Firmware Version 2/2 screen............................................................. 71
IP Network screen.............................................................................. 71
Scene Copy screen............................................................................ 72
Initialize screen .................................................................................. 72
Hour Meter screen ............................................................................. 73
HDMI Status screen........................................................................... 74
Error Status screen............................................................................ 75
Camera menu item table..................................................................... 76
Displaying the web screen ................................................................. 83
Displaying the web screen using a personal computer...................... 83
Switching between the Live screen [Live] and Web setup screen
[Setup] ........................................................................................... 85
Logging into the Web screen ............................................................. 85
Web screen operations....................................................................... 86
Live screen [Live]............................................................................... 86
Web screen configurations ................................................................ 91
Web setup screen [Setup].................................................................. 91
Setting status screen [Setting status]................................................. 92
Basic screen [Basic]........................................................................... 93
Image screen [Image/Audio]............................................................ 100
Collaboration capability [Linkage] .................................................... 122
User management screen [User mng.]............................................ 124
Network setup screen [Network]...................................................... 126
Maintenance screen [Maintenance]................................................. 142
Displaying the web screen using a personal computer equipped
with a touch panel ......................................................................... 146
Displaying the web screen using a mobile terminal ...................... 148
Camera control screen [Camera Control] ........................................ 148
Limiters............................................................................................... 150
Setting/releasing the limiters ........................................................... 151
Basic limiter operations.................................................................... 151
Setting the limiters ........................................................................... 151
Releasing the limiters....................................................................... 151
Resetting the limiters ....................................................................... 151
Safe mode .......................................................................................... 152
Concerning the safe mode............................................................... 152
Detection of equipment trouble........................................................ 152
Troubleshooting ................................................................................ 153
Specifications .................................................................................... 161
Index ................................................................................................... 163
6 7

Before use
Overview
• This product is an all-in-one pan-tilt head remote camera that supports
4K HDMI output and multi-format 3G/SDI.
• Equipped with an optical 24x zoom lens and 4K-compatible 1/2.5 type
MOS sensor, it is possible to shoot high-quality images with a high
degree of realism with the horizontal resolution of 1500 lines.
With its built-in image-shake correction and night mode functions, the
unit can shoot in a wide range of environments.
• This product is compatible with High Bandwidth NDI (hereafter, NDI)
and NDI|HX version 2 technology of NewTek, Inc.
The problem of IP transmission delay and image degradation of
NDI|HX will be resolved with High Bandwidth NDI.
• The problem of operating noise in pan/tilt operations has been
significantly reduced by adopting the Direct Drive system.
• The unit supports transmission of video to NewTek High Bandwidth
NDI and NDI|HX version 2 compatible software applications and
hardware devices over a network.
• When a controller is connected, camera operations can be performed
smoothly via IP control or serial control.
• The unit features a night mode that exposes subjects to infrared rays,
making it possible to shoot even under low-light conditions.
• When the unit is connected to a personal computer via an IP network,
it can be operated via a web browser.
• Connection with a Panasonic camera controller is also possible via
Panasonic's proprietary serial communication format.
• The unit is available in white (AW-UE80W) or black (AW-UE80K) to
suit your intended application and environment.
Computer requirements
CPU 7th Generation Intel®Core™ (Kaby Lake or later)
recommended
Memory For Windows:
4 GB or more
For Mac:
4 GB or more
Network function 100BASE-T/TX or 1000BASE-T,
RJ-45 connector
Image display Resolution: 1920 × 1080 pixels or more
Color generation: True Color 24-bit or more
Supported operating
systems and
web browsers
For Windows:
Microsoft®Windows®10
Windows®Internet Explorer®11
64-bit/32-bit
Microsoft Edge
Google Chrome
For Mac:
macOS v11.0.1
Safari 14.01
macOS v11.0.1
Google Chrome
macOS v10.15
Google Chrome
macOS v10.14
Google Chrome
For iPhone, iPad:
iOS
Safari
iPadOS
For Android:
Android OS
Google Chrome
Other Adobe®Reader®
(for viewing the operating instructions available on
the website)
8

IMPORTANT
• Failure to provide the required personal computer
environment may slow down the delineation of the images on
the screen, make it impossible for the web browser to work
and cause other kinds of problems.
<NOTE>
• Depending on the software version of the unit, an update may be
necessary.
• For the latest information on compatible operating systems and web
browsers, visit the support desk at the following website.
https://pro-av.panasonic.net/
Disclaimer of warranty
IN NO EVENT SHALL Panasonic Corporation BE LIABLE TO ANY
PARTY OR ANY PERSON, EXCEPT FOR REPLACEMENT OR
REASONABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
AANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION,
DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR
EXEMPLARY, ARISING OUT OF OR RELATING TO THE
PRODUCT;
BPERSONAL INJURY OR ANY DAMAGE CAUSED BY
INAPPROPRIATE USE OR NEGLIGENT OPERATION OF THE
USER;
CUNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATION
OF THE PRODUCT BY THE USER;
DINCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES
ARE NOT DISPLAYED, DUE TO ANY REASON OR CAUSE
INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
EANY PROBLEM, CONSEQUENTIAL INCONVENIENCE,
OR LOSS OR DAMAGE, ARISING OUT OF THE SYSTEM
COMBINED BY THE DEVICES OF THIRD PARTY;
FANY DEMANDS FOR COMPENSATION, CLAIMS, ETC.
OCCASIONED BY THE INFRINGEMENT OF PRIVACY BY
INDIVIDUALS OR ORGANIZATIONS WHOSE IMAGES WERE
SHOT BY THE USER BECAUSE THESE IMAGES (INCLUDING
THE RECORDINGS MADE) WERE MADE AVAILABLE BY THE
USER BECAUSE IN THE PUBLIC DOMAIN FOR SOME REASON
OR OTHER OR BECAUSE THE IMAGES ENDED UP BEING
USED FOR PURPOSES OTHER THAN THE ONE DESCRIBED
ABOVE;
GLOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
Network security
As the unit intended to be used while connected to a network, the
following security risks exist.
ALeakage or theft of information through the unit
BUnauthorized operation of the unit by persons with malicious intent
CInterference with or stoppage of the unit by persons with malicious
intent
It is your responsibility to take precautions, such as those described
below, to protect yourself against the above network security risks.
Panasonic does not accept any responsibility for damage of this type.
• Use the unit in a network secured by a firewall, etc.
• If the unit is connected to a network that includes personal computers,
make sure that the system is not infected by computer viruses or other
malicious programs (using a regularly updated antivirus program, anti-
spyware program, etc.).
• Protect your network against unauthorized access by restricting users
to those who log in with an authorized user name and password.
• After accessing the unit as an administrator, be sure to close all web
browsers.
• Change the administrator password periodically.
• To avoid passwords that can be guessed easily by third parties,
set a password of at least 8 characters in length, including at least
3 different types of characters, such as upper case, lower case,
numbers, and symbols.
• Restrict access to the unit by authenticating the users, for example,
to prevent setting information stored on the unit from leaking over the
network.
• Do not install the unit in locations where the unit, cables, and other
parts can be easily damaged or destroyed by persons with malicious
intent.
• Avoid connections that use public lines.
<NOTE>
Notes on user authentication
• User authentication on the unit can performed via digest authentication
or basic authentication. If basic authentication is used without the use
of a dedicated authentication device, password leaks may occur.
We recommend using digest authentication or host authentication.
Usage restrictions
• We recommend connecting the unit, controller, and any computers to
the same network segment.
Events based on settings inherent to the network devices, for example,
may occur in connections that include different segments, so be sure
to perform checks prior to operation.
8 9
Before use (continued)

 Multi‑format support
• You can switch between the following formats via the camera
menus or a web browser.
[4K format (only HDMI output supported)]
2160/59.94p, 2160/50p, 2160/29.97p*1 , 2160/25p*1 , 2160/24p*1 ,
2160/23.98p*1
[HD format (SDI supported)]
1080/59.94p, 1080/50p, 1080/59.94i, 1080/50i, 1080/29.97p*1 ,
1080/25p*1 , 1080/23.98p*2 , 1080/29.97PsF, 1080/25PsF,
1080/23.98PsF, 1080/24p*1 , 1080/23.98p*1 , 720/59.94p, 720/50p
[HD format (HDMI supported)]
1080/59.94p, 1080/50p, 1080/59.94i, 1080/50i, 1080/29.97p*1 ,
1080/25p*1 , 1080/23.98p*3 , 1080/24p*1 , 1080/23.98p*1 ,
720/59.94p, 720/50p
*1Native output
*2OVER 59.94i output (your monitor may recognize the signal as
59.94i).
*3OVER 59.94p output (your monitor may recognize the signal
as 59.94p).
 1/2.5‑type 4K MOS sensor and high‑
performance 24x zoom lens featured
• The latest 1/2.5-type 4K MOS sensor and DSP (Digital Signal
Processor) are incorporated. High-quality pictures are obtained by
video processing in many different kinds of ways.
• In addition to its optical 24x zoom lens, the unit comes with a 10x
digital zoom to achieve high-quality images that overflow with
ambiance. Zoom up to 36x is possible (up to 28x in 4K mode)
while maintaining the picture quality with the use of iZoom.
• A dynamic range stretcher (DRS) function that compensates for
overexposure and loss of dark detail and a digital noise reduction
(DNR) function for minimizing image lag even in dark locations
and shooting scenes clearly are incorporated to reproduce clean
and clear images in a wide range of applications.
• Even if the camera has to be installed in a limited space, a wide
range can be covered due to the possibility of wide-angle shooting
across 74.1° horizontally.
 Easy operation of unit enabled by its
integration with a high‑performance pan‑tilt
head unit
• Operations at the high speed of 180°/s
• Wide rotational angles with a panning range of ±175° and a tilting
range from –30° to 90°
• Quiet operation with noise levels of NC25 or less
• Storage of up to 100 positions in the preset memory
(The number of preset memories that can be used varies from one
controller to another.)
 Built‑in night mode
• The unit supports infrared shooting.
By exposing subjects to infrared rays, shooting under ordinarily
difficult low-light conditions is possible.
(Image output will be in black and white.)
• The iris will be fixed at open.
 Supports optical image stabilization (O.I.S.)
• Image stabilization is implemented if shaking of the unit is
detected, thus reducing shaking of the images.
Optical image stabilization means less image deterioration,
making highly precise vibration mitigation possible.
 IP image output functions
• The unit is equipped with image compression and IP transmission
LSI capabilities. Output at a maximum of 60 frames each second
is possible at full HD picture quality.
• Operation with IP control allows for a wide range of applications,
such as controlling the camera from remote locations.
 High degree of compatibility with Panasonic’s
currently available controllers, enabling a
flexible system to be put together
• A maximum of five units can be operated by serial control from
one of Panasonic’s currently available controllers (AW-RP150,
AW-RP60).
The unit can also be used together with the cameras and pan-tilt
head unit systems currently available from Panasonic Corporation
so that an existing system can be used to advantage to put
together a system that is even more flexible.
<NOTE>
• It may be necessary to upgrade the version of the controllers
in order to support the unit. For details on upgrading, visit the
support page on the following website.
https://pro-av.panasonic.net/
The maximum distances between the units and controller is
1000 meters (3280 ft). (when serial control is exercised)
Use of an external device or some other means must be
provided separately in order to extend the video signal
connections.
 Easy construction of systems thanks to
integrated design used for pan‑tilt head,
camera and lens
• By integrating the camera, lens and pan-tilt head into a single unit,
it is now easier to construct systems.

Use of easy‑to‑operate wireless remote control
(optional accessory) is possible
• A wireless remote control capable of operating up to four units can
be used.
It can easily be used to set the various functions or switch
between them while viewing the menu screens.
 Flexible camera layout enabled by simple
connection and installation
• This unit features excellent connectivity and installability thanks
to the IP control; a lightweight main unit, and the turn-lock
mechanism, which enables the user to install it on his or her own
(only when used indoors).
<NOTE>
• Bear in mind that this unit is designed to be used indoors only:
It cannot be used outdoors.
 While including a 4K‑compatible or different
kinds of interface, the unit still has the same
installation footprint as previous models
• The unit maintains the compact installation footprint of previous
models.
 Easy connections and settings courtesy of IP
control
• Up to two hundred units can be operated by IP connection from a
Panasonic controller (AW-RP150, AW-RP60).
(The maximum length of the LAN cables is 100 meters (328 ft).)
• Network connection with AW-RP150 or AW-RP60 requires setup
of an initial account. (→ page 28)
When an initial account is not set up, AW-RP150 or AW-RP60 can
detect but cannot control this unit.
Features
10

 PoE++ *4eliminates need for camera power
configurations
• Configurations for camera's power supply are not necessary when
the unit is connected to a network device that supports the PoE++
standard (IEEE 802.3bt compliant)*5 .
Software authentication (LLDP) is also supported, but it may be
necessary to make settings on the network device (IEEE 802.3bt
compliant)*5.
<NOTE>
• If the AC adaptor and a PoE++ power supply are connected
simultaneously, the AC adaptor will have priority. If the AC adaptor
is disconnected while both power supplies are connected, the unit
will restart automatically, and the image will be interrupted.
• Use a Category 5e cable or higher when using a PoE++ power
supply. The maximum length of the cable between the power
supply unit and the unit is 100 meters (328 ft). Using a cable that
is lower than Category 5e may result in reduced power supply
capabilities.
*4Power over Ethernet Plus Plus. Referred to as "PoE++" in this
manual.
*5For details on PoE++ power supply devices for which operation
has been verified, consult your local dealer.
Accessories
Check that the following accessories are present and accounted for.
• After removing the product from its container, dispose of the power cable cap (if supplied) and packing materials in an appropriate manner.
Mount bracket for installation surface
(Hanging/Desktop) (1)
Main unit mounting screw (with flat
washer, spring washer)
M3×6 mm (1/4 inches) (1)
Drop‑prevention wire (1)
Drop‑prevention wire mounting screw (1)
(comes attached to the unit)
Bracket mounting screws (bind‑head)
M4×10 mm (13/32 inches) (4)
AC adaptor (1)
Power cable
for AW‑UE80WP, AW‑UE80KP (1) for AW‑UE80WE, AW‑UE80KE (2) for AW‑UE80WED, AW‑UE80KED (1)
●For U.K. and Saudi Arabia
●For Continental Europe, etc.
●For India only
Optional accessories
z Wireless remote control AW‑RM50AG (Size “AA” dry battery x 2, obtained separately)
z Direct ceiling mount bracket WV‑Q105A
<NOTE>
• For details on optional accessories, refer to the catalog or consult your local dealer.
10 11
Features (continued)

 Do not use the unit in oily‑smoky or dusty
places.
Performance may be adversely affected if small particles or other
foreign objects get inside the product.
Take extra care in environments where a special effect such as
theatrical smoke is used.
 Do not allow foreign matter to make contact
with the rotating parts.
Failure to obey may cause the unit to malfunction.
 Maintenance
Turn off the unit’s power before proceeding with maintenance.
Failure to obey may result in injuries.
Wipe the surfaces using a soft dry cloth. Avoid all contact with
benzine, paint thinners and other volatile substances, and avoid
using these substances. Otherwise, the casing may become
discolored.
 Hold the bottom surface with both hands for
picking up this unit.
If you hold the lens part or the sides, it will put a load strain on the
motor and cause a malfunction.
 Do not turn the camera head by hand.
Turning the camera head by hand may cause the unit to
malfunction.
 About the lens/pan‑tilt head
If the lens, pan-tilt head, and other parts are not operated for a long
period of time, the viscosity of the grease applied inside them may
increase and operation may become no longer possible. Move the
lens and pan/tilt head regularly.
 Shoot under the proper lighting conditions.
To produce pictures with eye-pleasing colors, shoot under the
proper lighting conditions.
The pictures may not appear with their proper colors when shooting
under fluorescent lights. Select the proper lighting as required.
 To ensure a stable performance in the long
term
Using the unit for prolonged periods in locations where the
temperature and humidity levels are high will cause its parts to
deteriorate, resulting in a reduction of its service life.
(Recommended temperature: Max. 35 °C (95 °F))
Ensure that a cooling unit or heating unit will not blow any air
directly toward the installation location.
 Do not point the camera at
strong lights.
When parts of the MOS sensor are
exposed to spotlights or other strong
lights, blooming (a phenomenon where
the edges of strong lights become
blurred) may occur.
Bright subject
Blooming
 What happens with high‑brightness subjects
Flare may occur if an extremely bright light source is pointed at
the lens. In a case like this, change the angle or take some other
remedial action.
 When using the automatic functions
• In the [Scene] such as the camera menu, the initial settings on
some items has been set to auto, making it impossible for these
items to be operated manually. To operate them manually, switch
from the auto settings to the manual settings as required.
• When using the ATW (auto tracking white adjustment) function
under fluorescent lights, the white balance may vary.
• In some situations, it may be hard to focus at the auto setting. In
cases like this, select the manual setting, and focus manually.
 Zooming and focusing
When the focus is set manually, out-of-focusing may occur during
zooming.
After zooming, if necessary, either adjust the focus or set the focus
to auto.
When using the focus at the manual setting, proceed with zooming
after setting the focus position at the Tele end where the focusing
accuracy is higher. (However, if the distance from the unit to the
subject is less than 1.2 meters (3.9 ft), the subject may shift out of
focus at the Wide end.)
If zooming is performed to the Tele end after having adjusted the
focus at the Wide end, out-of-focusing may occur.
 Operation of the lens when the power is turned
on
When the unit’s power is turned on, the zoom, focus and iris are
adjusted automatically.
 The unit comes with the safe mode.
The safe mode is function designed to protect the unit from damage.
For details, refer to “Concerning the safe mode” (→ page 153).
 Concerning the HDMI interface standard
This unit has been certified as HDMI-compatible, but on rare
occasions images may not be displayed depending on the HDMI
device which has been connected to the unit.
 Color bars
Color bars are used to adjust the color phase, and the widths and
positions of these bars may differ from other models.
 H.264/H.265 patent pool licensing
This product is licensed based on the AVC Patent Portfolio License,
and the license does not extend beyond uses by users, who engage
in the acts described below, for their own personal and non-profit
applications.
(i) Recording of image information in compliance with the AVC
standard (hereafter, “AVC videos”)
(ii) Playing of AVC videos recorded by consumers engaging
in personal activities or AVC videos acquired from licensed
providers
For details, visit MPEG LA, LLC website (http://www.mpegla.com).
Operating precautions
12

 Concerning PoE++ power supply
The unit complies with the IEEE 802.3bt.
Use a compatible Ethernet hub and PoE++ injector to use a PoE++
power supply.
Software authentication (LLDP) complies with IEEE 802.3bt, but it
may be necessary to make settings on the network device.
For details on Ethernet hubs and PoE++ injectors for which
operations have been verified, consult your local dealer.
 Turn off the power before connecting or
disconnecting the cables.
This unit is not equipped with a power switch.
Disconnect the AC adaptor power plug or turn off the PoE++ power
supply device before connecting or disconnecting cables.
 When the unit is not in use
Turn off the unit’s power when it is not in use.
When the unit is no longer to be used, make sure to remove the
camera and mount bracket rather than leaving them in place.
 Do not touch the optical system parts.
The optical system parts are vital to the operation of the camera.
Under no circumstances must they be touched.
In the unlikely event that they have become dusty, remove the
dust by using a camera blower or by wiping them gently with a lens
cleaning paper.
 Do not point the camera directly at the sun or a
laser beam no matter whether it is turned on or
not.
Taking images of the sun, laser beams, or other brightly lit subjects
for prolonged periods of time may damage the CCD.
 Personal computer used
If the same image is displayed for a prolonged period on a personal
computer's monitor, the monitor may be damaged. Use of a screen
saver is recommended.
 Concerning the IP address setting
Do not run the Easy IP Setup Software on a multiple number of
personal computers for a single camera and set the IP address at
the same time.
Otherwise, you will be unable to complete the proper procedure and
set the IP address correctly.
 About consumables
The following parts are consumables. Replace them using the
lifespans as a guide.
The lifespans may vary depending on the operating environment
and operating conditions. The lifespans are a guide for when the
unit is used at 35 °C (95 °F).
• Cooling fan: Approx. 15000 hours
Contact your dealer regarding replacements.
 Disposal of the unit
When the unit has reached the end of its service life and is to be
disposed of, ask a qualified contractor to dispose of the unit properly
in order to protect the environment.
 Remove lens cap and pan stopper when
turning on power
Make sure you remove the lens cap and pan stopper when turning
on the power.
If there is an error, turn the power on again after removing the lens
cap and pan stopper.
 Transportation
The camera unit is constructed to rotate easily. As malfunctions in
camera movement may occur, transport after securing the camera
unit so that it does not rotate.
AFace the lens down, then secure the lens part and camera head
together with tape.
BUse tape to secure the camera head and pedestal in several
locations.
• The lens cap and pan stopper are not intended to guarantee
protection of the camera unit during transport. When transporting
the unit, be sure to use tape to secure it.
 Moving the unit
• When carrying the unit, take care not to apply strong shocks or
drop it.
• Remove connection cables when moving the unit.
• Turn off the system power when moving the unit.
• Wrap the unit in cushioning material, etc., when moving the unit so
that impacts do not damage it.
• Treat the unit carefully so that vibrations or impacts do not
damage it.
12 13
Operating precautions (continued)

 Information on software used with this product
This product includes GNU General Public License (GPL) and GNU Lesser General Public License (LGPL) licensed software, and the customer is
entitled to obtain, modify, or redistribute the source code for the software.
This product includes MIT Licensed software.
This product includes BSD Licensed software.
For details on obtaining the source codes, visit the following website.
https://pro-av.panasonic.net/
However, do not contact Panasonic for questions regarding obtained source codes.
 Concerning the installation location
Install the unit in a stable location which will not be susceptible to
shaking. If the unit is installed in a location which is susceptible to
shaking, this will cause the unit’s images to shake in turn.
Install the unit after conferring in detail with your dealer.
Install the unit on a ceiling that is strong enough (such as a concrete
ceiling).
If the unit is to be installed on a ceiling which is not strong enough,
reinforce the ceiling sufficiently first.
Through the adoption of the Direct Drive system and Panasonic
proprietary technology, we have achieved quietness and high
precision in panning and tilting.
In order to get the most from the characteristics of the Direct Drive
system, install in a stable location that does not shake and that has
sufficient stiffness. Shaking of the installation location can be the
cause of performance deterioration and malfunctions in the camera.
If the camera is installed in a location with insufficient stiffness,
the pan and tilt control characteristics may be adversely affected,
leading to unstable operation.
• In environments such as the following, there may be unusual
operation sounds during pan and tilt, and operational errors may
occur.
If you are concerned about unstable pan and tilt operations after
installation, please contact your dealer.
<Installation examples that may cause performance
deterioration and malfunctions>
ASingle point attachment to a cylindrical pole structure that has a
small diameter
BSingle point attachment to a movable structure
 
14
Operating precautions (continued)

This unit can be operated by remote control using a wireless
remote control (model number: AW‑RM50AG) purchased
separately.
Check out the following points before using the wireless remote
control.
z Point the wireless remote control at the unit’s wireless
remote control signal light‑sensing area (front panel or
back panel), and operate it within a range of 10 meters
(32.8 ft) from these areas.
z Refer to <Layout of wireless remote control signal
light‑sensing areas> on the right.
z The signal sensing distance is reduced if the angle at
which the wireless remote control signals are sensed is
increased.
The light-sensing sensitivity is reduced to about one-half when the
wireless remote control is pointed at an angle of 40 degrees from
each position in front of a wireless remote control signal light-sensing
area (front panel or back panel).
If the remote control is operated from the behind the unit, it may be
either difficult or impossible to perform the desired operations.
z If the unit is installed near fluorescent lights, plasma
monitors or other such products or if the unit is
exposed to sunlight, the effects of the light may make it
impossible for the unit to be operated using the wireless
remote control.
Be sure to follow the steps below for installation and use.
• Take stesps to ensure that the wireless remote control signal light-
sensing area will not be exposed to the light from fluorescent lights,
plasma monitors or other such products or from the sun.
• Install the unit away from fluorescent lights, plasma monitors and
other such products.
z For about 10 minutes even after the batteries have been
removed from the wireless remote control, the selection
of the operation to be performed (the CAMERA <1>, <2>,
<3> or <4> button which was pressed last) will remain
stored in the memory.
When a longer period of time elapses, however, the
selection is reset to the status established when the
CAMERA <1> button was pressed.
<Layout of wireless remote control signal light‑sensing areas>
<NOTE>
• The arrows in the figure below show the light-sensing directions in
which the wireless remote control signals travel.
Wireless remote control
signal light‑sensing area
(back panel, 1 place)
Wireless remote
control signal light‑
sensing area (front
panel, 2 places)
Approx. 45° Approx. 45°
• Top view
• Rear panel view
Wireless remote control signal
light‑sensing area
Wireless remote control (optional accessory)
14 15

Camera unit
RS-422
IR ID
3G SDI OUT
G/L IN
AUDIO IN
LAN
LINK ACT
DC IN 12V
SERVICE
1
2
4
3
5
8
6
9
7
21
10 611 1512 13
201917 1816
14
7
Rear panel
Bottom panel
1. Mount bracket for installation surface (supplied
accessory)
Mount this bracket onto the installation surface, and then attach the
camera main unit to the bracket.
2. Drop‑prevention wire
This wire is screwed down to the bottom panel of the camera main
unit. Loop the circle part of the wire around the hook of the mount
bracket.
3. Status display lamp
This lights in the following way depending on the status of the unit.
Orange Light up When the standby status is established
Blink twice When a signal not matched by the remote control
ID has been received from the wireless remote
control (optional accessory) while the power is on
Green Light up When the power is on
Blink twice When a signal matched by the remote control
ID has been received from the wireless remote
control (optional accessory) while the power is on
Blinking
rapidly
When the initialization process is complete
Red Light up When trouble has occurred in the unit
Blinking
slowly
Firmware being updated
Blinking
rapidly
When a PoE++ software authentication error has
occurred
4. Ventilation holes
Blocking the ventilation holes may cause a malfunction. Make sure
there is sufficient space around the ventilation holes.
5. Pan head
This rotates in the right and left direction.
6. Wireless remote control signal light‑sensing area
There are three light-sensing areas on the front and rear panels of the
camera pedestal.
7. Hole for securing the camera pedestal
This hole is provided in the bottom panel of the camera pedestal.
8. Camera head
This rotates in the up and down direction.
9. Tally lamp
This comes on or goes off in response to the control from the
controller but only when “On” has been selected as the tally lamp use
setting. The tally lamp is red or green.
Red Light up When receiving a red tally signal
Blink once When a Pan/Tilt limit is set
Blink twice When the Pan/Tilt limit is canceled
Blink three
times
When start up of this unit is complete
Green Light up When receiving a green tally signal
Parts and their functions
16

10.RS‑422 connector <RS‑422>
This RS-422 connector (RJ-45) is connected when exercising serial
control over the unit from an external device. Use a cable with the
following specifications for the connection to this connector.
Furthermore, by shorting the R-TALLY signal (2-pin) with the GND
(1-pin), it is possible to light the tally lamp (red) in the camera head
section of the unit.
<NOTE>
• Do not connect PoE cable to the RS-422 port.
• Do not apply a voltage to the R_TALLY_IN signal pin.
• With the menu settings, the ON/OFF for red tally signals or green
tally signals received by this unit can be output via pin 7 or pin
8. Output is by contact output, and normally is “OPEN”, then it
becomes “MAKE” for output. (→ page 63)
LAN cable*1(category 5e or above, straight cable), STP,
max. 1000 m (3280 ft)
*1Use of an STP (shielded twisted pair) cable is recommended.
Pin
No. Signal Pin No. Signal
1 GND 5 TXD+
2 R_TALLY_IN 6 RXD+
3 RXD– 7
OPTION_OUT1
4 TXD– 8 OPTION_OUT2
Example OPTION_OUT1, OPTION_OUT2 connector
connections
AW-UE80 OPTION_OUT1
OPTION_OUT2
GND
Voltage: Maximum DC12 V
Current: Maximum 100 mA
11.G/L IN connector <G/L IN>
This is the external sync signal input connector.
This unit supports BBS (Black Burst Sync) and tri-level
synchronization.
Supply to this connector the signals that correspond to the video
signal format which has been set.
Frequency: 59.94 Hz, 29.97 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/59.94p ―1080/59.94i 480/59.94i
2160/29.97p 1080/29.97p
1080/29.97PsF
1080/59.94p ―
1080/59.94i ―
1080/29.97p 1080/29.97p
1080/29.97PsF
1080/29.97PsF 1080/29.97p
1080/29.97PsF
1080/23.98p
over 59.94i
―
720/59.94p 720/59.94p
Frequency: 50 Hz, 25 Hz
Format External sync signal input format
Tri‑level sync BBS
2160/50p ―1080/50i 576/50i
2160/25p 1080/25p
1080/25PsF
1080/50p ―
1080/50i ―
1080/25p 1080/25p
1080/25PsF
1080/25PsF 1080/25p
1080/25PsF
720/50p 720/50p
Frequency: 24 Hz
Format External sync signal input format
Tri‑level sync
2160/24p 1080/24p
1080/24PsF
1080/24p
Frequency: 23.98 Hz
Format External sync signal input format
Tri‑level sync
2160/23.98p 1080/23.98p
1080/23.98PsF
1080/23.98p
1080/23.98PsF
12.AUDIO IN connector <AUDIO IN>
Inputs external audio (microphone, line).
13. LAN connector for IP control <LAN LINK/ACT>
This LAN connector (RJ-45) is connected when exercising IP control
over the unit from an external device. Use a LAN cable*1(category 5e
or above, STP, max. 100 m (328 ft)) for connection.
*1Use of an STP (Shielded Twisted Pair) cable is recommended.
14.DC IN connector <12V IN >
Connect the AC adaptor supplied with the unit to this connector to
supply the DC 12 V voltage to the unit.
AC adaptor
Be sure to use the supplied AC adaptor.
16 17
Parts and their functions (continued)

15.Cable clamp
This is used to hold the cable connection to the DC IN connector and
prevent it from becoming disconnected.
16.IR ID switches <IR ID>
CAM1 CAM2 CAM3 CAM4
These are used to select the ID of the wireless remote control
(optional accessory). (→ page 26)
The IR ID switch settings “CAM1” to “CAM4” correspond to the
<CAM1> to <CAM4> buttons on the wireless remote control.
17.3G SDI OUT connector <3G SDI OUT>
This is an SDI video signal output connector. Depending upon the
output signal format, 3G-SDI or 1.5G-SDI signals are output.
18.Service switches <SERVICE>
Perform switch settings before turning the unit on.
RS-422
IR ID
3G SDI OUT
G/L IN
AUDIO IN
LAN
LINK ACT
DC IN 12V
SERVICE
Service switches
Function Factory settings
SW1 Switches for initialization
(Refer to the explanations in “Initialization 1”
and “Initialization 2”)
OFF
SW2
Always leave at OFF (used for factory
adjustments)
OFF
SW3 OFF
SW4 OFF
Initialization 1
• Reset the user authentication settings and host authentication
settings for network connection.
(This will delete all the registered user information (IDs/passwords)
and host information (IP addresses).)
• With the IR ID switches and service switches set as shown below,
turn on the power of the unit.
SW1
ON
OFF
SW2 SW3 SW4
<NOTE>
• When initialization is complete, the status display lamp on the
front of the unit blinks green. Set the service switches back to their
original positions (SW1 to SW4 all OFF), then restart the unit.
Initialization 2
• The unit is reset to the state it was in at the time of purchase. (All
camera menu setting values and network setting values are reset.)
• With the IR ID switches and service switches set as shown below,
turn on the power of the unit.
SW1
ON
OFF
SW2 SW3 SW4
<NOTE>
• When initialization is complete, the status display lamp on the
front of the unit blinks green. Set the service switches back to their
original positions (SW1 to SW4 all OFF), then restart the unit.
19. HDMI connector <HDMI>
This is the HDMI video output connector.
20.Ground connector
Connects to the ground connector on a wall outlet, ground bar, etc.
for grounding. (→ page 6)
21.Tripod screw holes
(Screw: 1/4-20 UNC, ISO 1222 [6.35 mm])
Use these screw holes when securing the unit to a tripod, etc.
Place the tripod on a completely flat and level surface.
Tighten the screws by hand to mount the tripod securely.
Use screw for mounting the tripod that satisfy the following standard.
Screw for mounting tripod
1/4-20UNC, ISO1222 (6.35 mm)
4.5 mm to 7 mm
(3/16 inches to 9/32 inches)
18
Parts and their functions (continued)

 Output conditions for each video format
Frequency System Format HDMI 3G SDI OUT NDI
59.94Hz
2160/59.94p 2160/59.94p
1080/59.94p
1080/59.94p
1080/59.94i 1080/59.94p
2160/29.97p 2160/29.97p
1080/29.97p 1080/29.97p 1080/29.97p
1080/59.94p 1080/59.94p 1080/59.94p
1080/59.94i 1080/59.94p
1080/59.94i 1080/59.94i 1080/59.94i 1080/59.94p
1080/29.97p 1080/29.97p 1080/29.97p 1080/29.97p
1080/29.97PsF 1080/29.97p 1080/29.97PsF No output
1080/23.98p over 59.94i 1080/23.98p over 59.94p 1080/23.98p over 59.94i No output
720/59.94p 720/59.94p 720/59.94p 720/59.94p
50Hz
2160/50p 2160/50p
1080/50p
1080/50p
1080/50i 1080/50p
2160/25p 2160/25p
1080/25p 1080/25p 1080/25p
1080/50p 1080/50p 1080/50p
1080/50i 1080/50p
1080/50i 1080/50i 1080/50i 1080/50p
1080/25p 1080/25p 1080/25p 1080/25p
1080/25PsF 1080/25p 1080/25PsF No output
720/50p 720/50p 720/50p 720/50p
24Hz 2160/24p 2160/24p
1080/24p 1080/24p 1080/24p
1080/24p 1080/24p 1080/24p 1080/24p
23.98Hz
2160/23.98p 2160/23.98p
1080/23.98p 1080/23.98p 1080/23.98p
1080/23.98p 1080/23.98p 1080/23.98p 1080/23.98p
1080/23.98PsF 1080/23.98p 1080/23.98PsF No output
18 19
Parts and their functions (continued)

 IP video transmission output (multi‑channel display)
• When “Streaming mode” is set to “H.265”
Settings H.265(1) H.265(2) H.264(1) H.264(2) H.264(3) H.264(4) JPEG(1) JPEG(2) JPEG(3)
Resolution
1920 × 1080 1920 × 1080
————
1920×1080
1280×720 1280×720 1280×720
640×360 640×360 640×360 640×360
320×180 320×180 320×180
Frame rate
System
frequency
59.94Hz
60fps 60fps
————
30fps 30fps 30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
50Hz
50fps 50fps
————
25fps 25fps 25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
29.97Hz
30fps 30fps
————
30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
25Hz
25fps 25fps
————
25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
24/23.98Hz
24fps 24fps
————
24fps 24fps 24fps
12fps 12fps 12fps
4fps 4fps 4fps
1fps 1fps 1fps
• If the resolution is 640x360, 60fps and 50fps cannot be selected.
• If the system frequency is 24/23.98Hz, the resolution for H.265 will be 1920x1080 only.
• You cannot make settings above the resolution and frame rate set by the system format.
• When “Streaming mode” is set to “SRT(H.265)”
Settings H.265(1) H.265(2) H.264(1) H.264(2) H.264(3) H.264(4) JPEG(1) JPEG(2) JPEG(3)
Resolution
1920 × 1080
—————
1920×1080
1280×720 1280×720
640×360 640×360 640×360
320×180 320×180 320×180
Frame rate
System
frequency
59.94Hz
60fps
—————
30fps 30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
50Hz
50fps
—————
25fps 25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
29.97Hz
30fps
—————
30fps 30fps 30fps
15fps 15fps 15fps
5fps 5fps 5fps
1fps 1fps 1fps
System
frequency
25Hz
25fps
—————
25fps 25fps 25fps
12.5fps 12.5fps 12.5fps
5fps 5fps 5fps
1fps 1fps 1fps
• The SRT(H.265) transmission mode (Transmission priority) cannot be selected.
• It is not possible to select SRT(H.265) mode when the system frequency is 24/23.98Hz.
• You cannot make settings above the resolution and frame rate set by the system format.
20
Parts and their functions (continued)