Panasonic DMC-FT2 Technical specifications

Before use, please read these instructions completely.
Please also refer to Operating
Instructions (PDF format)
recorded on the CD-ROM
containing the Operating Instructions
(supplied).
You can learn about advanced operation
methods and check the Troubleshooting.
GN
VQT2M46
until
2010/2/28
Basic Operating Instructions
Digital Camera
Model No. DMC-FT2
VQT2M46~Cover_eng.fm 1 ページ ２０１０年２月９日 火曜日 午前９時１５分

VQT2M46 (ENG)
2
Dear Customer,
We would like to take this opportunity to thank you for purchasing this
Panasonic Digital Camera. Please read these Operating Instructions
carefully and keep them handy for future reference. Please note that the
actual controls and components, menu items, etc. of your Digital Camera
may look somewhat different from those shown in the illustrations in these
Operating Instructions.
Carefully observe copyright laws.
•Recording of pre-recorded tapes or discs or other published or broadcast
material for purposes other than your own private use may infringe copyright
laws. Even for the purpose of private use, recording of certain material may be
restricted.
Information for Your Safety
IF THE POWER CORD OF THIS EQUIPMENT IS DAMAGED, IT MUST BE
REPLACED WITH AN ELECTRICALLY APPROVED POWER CORD.
Please be sure to read “(Important) About the waterproof/dustproof and
anti-shock performance of the camera”(P6) and “Maintenance and
waterproof performance”(P8) before using this unit underwater to prevent
the unit from being mishandled, which may cause water to seep in.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT
DAMAGE,
•DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING
OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH
AS VASES, SHALL BE PLACED ON THE APPARATUS.
•USE ONLY THE RECOMMENDED ACCESSORIES.
•DO NOT REMOVE THE COVER (OR BACK); THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THE SOCKET OUTLET SHALL BE INSTALLED NEAR THE
EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.
Product Identification Marking is located on the bottom of units.
DMC-FT2&TS2GN-VQT2M46_eng.book 2 ページ ２０１０年２月９日 火曜日 午前８時４６分

3
(ENG) VQT2M46
∫About the battery pack
•Do not heat or expose to flame.
•Do not leave the battery(ies) in an automobile exposed to direct sunlight for a
long period of time with doors and windows closed.
∫About the battery charger
•The battery charger is in the standby condition when the AC power supply cord
is connected. The primary circuit is always “live” as long as the power cord is
connected to an electrical outlet.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s instructions.
Warning
Risk of fire, explosion and burns. Do not disassemble, heat above 60 xC
or incinerate.
CAUTION!
•DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-IN
CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS
WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE
HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY
OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
•DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS WITH
NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS.
•DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS LIGHTED
CANDLES, ON THE UNIT.
•DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY FRIENDLY
MANNER.
DMC-FT2&TS2GN-VQT2M46_eng.book 3 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
4
∫Cautions for Use
•Always use a genuine Panasonic AC adaptor (DMW-AC5G; optional).
•
Always use a genuine Panasonic multi conversion adaptor (DMW-MCA1; optional).
•When using an AC adaptor, use the AC cable supplied with the AC adaptor.
•Do not use any other AV cables except the supplied one.
•Do not use any other cables except a genuine Panasonic HDMI mini cable
(RP-CDHM15, RP-CDHM30; optional).
Part numbers: RP-CDHM15 (1.5 m), RP-CDHM30 (3.0 m)
•Do not use any other USB connection cables except the supplied one.
In the event of abnormal operation (e.g. if the unit emits smoke or an unusual
smell), immediately stop operating the unit and consult the Panasonic
Customer Care Centre on 132600.
Keep the camera as far away as possible from electromagnetic
equipment (such as microwave ovens, TVs, video games etc.).
•If you use the camera on top of or near a TV, the pictures and sound on the
camera may be disrupted by electromagnetic wave radiation.
•Do not use the camera near cell phones because doing so may result in noise
adversely affecting the pictures and sound.
•Recorded data may be damaged, or pictures may be distorted, by strong
magnetic fields created by speakers or large motors.
•Electromagnetic wave radiation generated by microprocessors may adversely
affect the camera, disturbing the pictures and sound.
•If the camera is adversely affected by electromagnetic equipment and stops
functioning properly, turn the camera off and remove the battery or disconnect
AC adaptor (DMW-AC5G; optional). Then reinsert the battery or reconnect AC
adaptor and turn the camera on.
Do not use the camera near radio transmitters or high-voltage lines.
•If you record near radio transmitters or high-voltage lines, the recorded pictures
and sound may be adversely affected.
-If you see this symbol-
Information on Disposal in other Countries outside
the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your
local authorities or dealer and ask for the correct
method of disposal.
DMC-FT2&TS2GN-VQT2M46_eng.book 4 ページ ２０１０年２月９日 火曜日 午前８時４６分

5
(ENG) VQT2M46
Contents
Information for Your Safety ........................................................................... 2
(Important) About the waterproof/
dustproof and anti-shock performance of the camera................................... 6
Maintenance and waterproof performance ................................................... 8
• Using the camera underwater............................................................... 12
• Causes of water leak ............................................................................ 13
• Caring of the camera after using it underwater..................................... 14
Standard Accessories ................................................................................. 16
Names of the Components ......................................................................... 17
Charging the Battery ................................................................................... 19
About the Built-in Memory/the Card ............................................................ 21
Inserting and Removing the Card (optional)/the Battery ............................. 22
Setting Date/Time (Clock Set)..................................................................... 23
• Changing the clock setting.................................................................... 23
Setting the Menu......................................................................................... 24
Selecting the [REC] Mode........................................................................... 25
Taking pictures using the automatic function
(ñ: Intelligent Auto Mode) ......................................................................... 26
• Scene detection .................................................................................... 27
• AF Tracking Function............................................................................ 27
Recording Motion Picture............................................................................ 28
Playing back Pictures ([NORMAL PLAY])................................................... 29
Deleting Pictures ......................................................................................... 29
Reading the Operating Instructions
(PDF format) ............................................................................................... 30
Specifications.............................................................................................. 32
DMC-FT2&TS2GN-VQT2M46_eng.book 5 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
6
(Important) About the waterproof/
dustproof and anti-shock performance of
the camera
•Please observe the following precautions, and avoid using this camera in any
situation where the camera is subject to high water pressure. This camera’s
waterproof/dustproof rating complies with the “IPX8” and “IP6X” ratings.
Provided the care and maintenance guidelines described in this document are
strictly followed, this camera can operate underwater, to a depth not exceeding
10 m for a time not exceeding 60 minutes.¢1
•This camera also complies with “MIL-STD 810F (Method 516.5-Shock)”. The
camera has cleared a drop test from a height of 2 m onto 3 cm thick plywood. In
most cases this camera should not sustain any damage if dropped from a height
not exceeding 2 m.¢2
•Supplied accessories are not waterproof (excluding hand strap/silicon jacket).
¢1 This means that the camera can be used underwater for specified time in
specified pressure in accordance with the handling method established by
Panasonic. This does not guarantee no destruction, no malfunction, or
waterproofing in all conditions.
¢2 This does not guarantee no destruction, no malfunction, or waterproofing in all
conditions.
Observe the following precautions and avoid using under water pressure
exceeding the guaranteed performance, and in an environment with
excessive dust or sand.
Waterproofing is not guaranteed if the unit is subject to an impact as a result
of being hit or dropped etc.
If an impact to the camera occurs, it should be inspected (subject to a fee) by
a Panasonic’s service centre to verify that the waterproofing is still effective.
Any malfunction caused by customer misuse, or mishandling will not be
covered by the warranty.
Note
•The picture can become whitish if there is dirt e.g. fingerprints on the lens.
When it is dirty, lightly wipe the surface of the lens with soft and dry cloth.
DMC-FT2&TS2GN-VQT2M46_eng.book 6 ページ ２０１０年２月９日 火曜日 午前８時４６分

7
(ENG) VQT2M46
∫Handling of the camera
•Do not leave the camera for a long period of time in places where temperature is
very low (ski resort etc.) or very high (above 40 oC), inside a car under strong
sunlight, close to a heater, on the beach, etc. Waterproof performance may be
degraded.
•The inside of this unit is not waterproof. Do not open or close the card/battery
door or terminal cover close to the water by the sea, a lake or river, or with wet
hands.
•Waterproof function of the camera is for sea water and fresh water only.
•Operation may not be possible when snow or water on the zoom lever, mode
dial or camera [OFF/ON] button the buttons freezes at cold places like ski
resorts etc.
∫About the [PRECAUTIONS] demonstration display
•Please check beforehand to maintain the waterproof performance.
[PRECAUTIONS] is displayed when the power is turned
on for the first time after purchase, with the card/battery
door completely closed.
•The [PRECAUTIONS] screen will not display the next time
you turn on the power if you start the slide show by selecting
[YES], and then select [END] once it has completed. Select
[REPLAY] to see the slide show again.
Note
•It will automatically skip to clock setting screen if [NO] is selected before the
slide show starts.
•[PRECAUTIONS] is displayed every time the power is turned on if you exited the
slide show using a method other than selecting [END], such as turning off the
power while the slide show is playing.
•This can be also confirmed from [PRECAUTIONS] in the [SETUP] menu.
DMC-FT2&TS2GN-VQT2M46_eng.book 7 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
8
Maintenance and waterproof performance
∫To prevent water leaking into the camera, observe the following
items before using it.
∫Check that there is enough remaining battery power or memory in
the card.
∫Do not open or close the card/battery door or terminal cover in
places with sand and dust, near water, or with wet hands.
∫At purchase, the [LOCK] switch is in the locked state. When opening
the card/battery door and terminal cover, first release the lock.
•Release the lock by sliding the [LOCK] switch in the direction of the arrow until
the red area becomes visible, and open the card/battery door and terminal
cover.
A: [LOCK] switch (grey part)
B: Locked state
C:Red part
D: Released state
DMC-FT2&TS2GN-VQT2M46_eng.book 8 ページ ２０１０年２月９日 火曜日 午前８時４６分

9
(ENG) VQT2M46
Confirm that there are no foreign objects on inner side of
the card/battery door or terminal cover (Brubber seal
and Cplace where rubber seal meets).
•If there is any crack or deformation in the rubber seal inside the card/battery
door and terminal cover, get the camera inspected or repaired by the dealer or
an authorised Panasonic’s service centre.
If there is any foreign object, remove
with attached brush.
I: Brush (supplied)
•If there is any foreign object, such as lint, hair, sand, etc., on the
surrounding area, water will leak within a few seconds causing
malfunction.
A: Terminal cover
B: Rubber seal
C: Area where rubber seal
sits
D: Card/Battery door
E: Hair and lint
F: Sand and dust
G: Crack and deformation
H:Fluid
DMC-FT2&TS2GN-VQT2M46_eng.book 9 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
10
•Wipe it off with a dry soft cloth if there is any liquid.
•The integrity of the rubber seals may decrease after about 1 year, with use and
age. To avoid permanently damaging the camera the seals should be replaced
once each year. Please contact Panasonic’s Service Centre for related costs
and other information.
Example of foreign object on the inner side of the card/battery door
J: Area where rubber seal
sits (around the card/
battery compartment)
K: Rubber seal site (around
the card/battery cover)
Example of foreign object on the inner side of the terminal cover
L: Area where rubber seal
sits (around the
connection terminal)
M: Rubber seal site (around
the terminal cover)
DMC-FT2&TS2GN-VQT2M46_eng.book 10 ページ ２０１０年２月９日 火曜日 午前８時４６分

11
(ENG) VQT2M46
1:With the [LOCK] switch released, close the card/
battery door and terminal cover by pushing until you
hear a click.
•To prevent water seeping into the camera, be careful not to trap foreign
objects such as liquids, sand, hair or dust etc.
•Closing the door with the [LOCK] switch in the locked state may result in
damage or leaks.
2:Slide the [LOCK] switch in the direction of the arrow
until the visible red portion is no longer visible and the
switch is locked.
•If you use the camera without securely closing the door and cover, it may
open and close of its own accord.
Note
•If there is any foreign object, remove it
with attached brush.
•Sand and dust etc. will unintentionally
adhere to the camera by lodging in
between the gap around the card/
battery door or terminal cover when
used in the following locations:
–Where sand is floating, such as in the
sea or water etc.
–Where there is a lot of sand or dust,
such as at the beach or in a sand box
etc.
•To prevent unintentional opening of the card/battery door and terminal
cover, it is recommended to use the supplied silicon jacket.
N:Red part
O: [LOCK] switch (grey part)
P: Released state
Q: Locked state
DMC-FT2&TS2GN-VQT2M46_eng.book 11 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
12
•Use the camera underwater up to 10 m depth, water temperature from 0 oC to
40 oC, and not longer than 60 minutes continuously.
•If there is a water or dirt on the camera, use it after wiping it off with a dry soft
cloth and dried at well ventilated area.
•Do not open or close the card/battery door or terminal cover.
•Do not apply shock to the camera underwater. (Waterproof performance may not
be maintained, and there is a chance of water leak.)
•Do not dive into the water holding the camera. Do not use the camera at the
location where the water will splash strongly, such as rapid flow or waterfall.
(Strong water pressure may be applied, and it may cause malfunction.)
•The camera will sink in the water. Take care not to drop the camera and lose it
underwater by securely placing the hand strap around your wrist or similar
measure.
•Do not use it in the hot water over 40 oC (in the bath or hot spring).
•When the camera is splashed with detergent, soap, hot spring, bath additive,
sun oil, sun screen, chemical, etc., wipe it off immediately.
•Card and battery are not waterproof. Do not handle with a wet hand. Also, do not
insert wet card or battery into the camera.
Using the camera underwater
DMC-FT2&TS2GN-VQT2M46_eng.book 12 ページ ２０１０年２月９日 火曜日 午前８時４６分

13
(ENG) VQT2M46
•When the camera is used in the following conditions, a gap may occur between
the camera and the card/battery door or terminal cover, causing water to leak
and malfunction.
–When there are foreign objects, such as lint, hair, sand, etc., between the card/
battery door or terminal cover and the camera.
–When the rubber seal has deteriorated.
–When the [LOCK] switch is not closed on the card/battery door and terminal
cover.
Causes of water leak
A: Water will leak through
the gap formed.
B: water
C: Terminal cover
D: Card/Battery door
E: Hair and lint
F: Sand and dust
G: Crack and deformation
H:Fluid
DMC-FT2&TS2GN-VQT2M46_eng.book 13 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
14
1With the card/battery door and
terminal cover closed, rinse with
water, or if it was used in the sea,
soak the unit in fresh water pooled
in a shallow container for
10 minutes or less.
•If you have attached the silicon jacket,
be sure to rinse the camera after
removing it.
•Leaving the camera with foreign objects or saline matter on it may cause
damage, discolouration, corrosion, unusual odour, or deterioration.
2Wipe off the water, and dry the
camera by standing it on a dry
cloth in a well ventilated shaded
area.
3Confirm there is no water on the
camera, and open the card/battery
door and terminal cover.
4Wipe off any water or sand inside
the card/battery door and terminal cover with a soft dry cloth.
Caring of the camera after using it underwater
DMC-FT2&TS2GN-VQT2M46_eng.book 14 ページ ２０１０年２月９日 火曜日 午前８時４６分

15
(ENG) VQT2M46
∫This unit incorporates drain design
This unit incorporates drain design, draining
water in gaps in the camera [OFF/ON] button
and zoom lever etc. As a result of this, bubbles
may come out when you soak the unit in water,
but it is not a malfunction.
•Water droplets may attach to the card or the battery when the card/battery door
is opened without fully drying the camera after it is used underwater or soaked in
fresh water. Be sure to wipe off the water with a soft dry cloth in such cases.
•Do not open or close the card/battery door and terminal cover with droplets of
water still on the camera. The water droplets may seep into the camera, causing
condensation or failure.
Note
•Wipe off the water and dirt on the camera with a dry soft cloth.
•Do not leave the camera uncared for more than 60 minutes after using it
underwater. It may cause deterioration of the waterproof performance.
•After use at the seaside or under water, make sure that the card/battery door
and terminal cover are firmly closed and soak the unit in fresh water pooled in a
shallow container for 10 minutes or less.
•If the zoom lever, mode dial, or camera [OFF/ON] button do not move smoothly,
it may be caused by an adhesion of foreign objects. Using in such a state may
cause malfunctions, such as locking up, so wash off any foreign objects by
shaking the camera in fresh water. Confirm that the zoom lever, mode dial, and
camera [OFF/ON] button move smoothly after cleaning.
•After soaking or washing the unit, wipe off water drops with a dry soft cloth and
dry the unit in a shaded area which is well ventilated.
•Make sure that water is completely drained from the unit after soaking in water
by standing the unit on a dry cloth for a while.
•Do not dry the camera with hot air from dryer or similar. Waterproof performance
will deteriorate due to deformation.
•Do not use chemicals such as benzine, thinner, alcohol, or cleanser, or soap or
detergents.
•Example of water droplets around card/battery slot.
A: Water droplet
B:Battery
C:Card
DMC-FT2&TS2GN-VQT2M46_eng.book 15 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
16
Standard Accessories
Check that all the accessories are included before using the camera.
Product numbers correct as of January 2010. These may be subject to
change.
1 Battery Pack
(Indicated as battery pack or
battery in the text)
Charge the battery before use.
2 Battery Charger
(Indicated as battery charger or
charger in the text)
3 AC Cable
4 USB Connection Cable
5 AV Cable
6 CD-ROM
•Software:
Use it to install the software to your
PC.
•Operating Instructions
7Brush
8 Silicon Jacket
9 Hand Strap
10 Battery Case
•Supplied accessories are not waterproof
(excluding hand strap/silicon jacket).
•Keep the Brush out of reach of children
to prevent swallowing.
•The charger is stored inside the silicon
jacket.
•SD Memory Card, SDHC Memory Card
and SDXC Memory Card are indicated
as card in the text.
•The card is optional.
You can record or play back pictures
on the built-in memory when you are
not using a card.
•Consult the dealer or your nearest
Service Centre if you lose the supplied
accessories. (You can purchase the
accessories separately.)
4
5
DMW-BCF10E DE-A60A
7
9
VFC4393
12
K1HA14CD0004
K1HA14AD0003
8
VMG1932
3
K2CJ29A00002
VGQ0D56
10
VFC4364/
VFC4537
6
VFF0596
DMC-FT2&TS2GN-VQT2M46_eng.book 16 ページ ２０１０年２月９日 火曜日 午前８時４６分

17
(ENG) VQT2M46
Names of the Components
1Flash
2 Self-timer indicator/
AF assist lamp/LED light
3 Lens
4 LCD monitor
5 Motion picture button
6 [MENU/SET] button
7 [DISPLAY] button
8 [Q.MENU]/Delete button
9 Playback button
10 Mode dial
11 Cursor buttons
A:3/Exposure compensation/Auto
bracket/White balance fine
adjustment
B: 4/Macro mode/
AF Tracking
C: 2/Self-timer button
D:1/Flash setting button
In these operating instructions, the cursor buttons are described as
shown in the figure below or described with 3/4/2/1.
e.g.: When you press the 4(down) button
or Press 4
21 3
4511
786
9
10
DMC-FT2&TS2GN-VQT2M46_eng.book 17 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
18
12 Speaker
13 Microphone
14 Zoom lever
15 Camera [OFF/ON] button
16 Shutter button
17 Hand strap eyelet
•Be sure to attach the hand strap when
using the camera to ensure that you will
not drop it.
18 [HDMI] socket
19 [AV/DIGITAL/MULTI] socket
•When using an AC adaptor, ensure that
the Panasonic multi conversion adaptor
(DMW-MCA1; optional) and AC adaptor
(DMW-AC5G; optional) are used.
20 Tripod receptacle
•When you use a tripod, make sure the
tripod is stable when the camera is
attached to it.
21 Card/Battery door
22 Release lever
23 [LOCK] switch
e.g.: To make subjects appear closer
use (Tele)
Place your finger on the zoom lever,
and press [T] of the zoom lever
13 1412
1615
19
18 17
2120
22 23
DMC-FT2&TS2GN-VQT2M46_eng.book 18 ページ ２０１０年２月９日 火曜日 午前８時４６分

19
(ENG) VQT2M46
Charging the Battery
∫About batteries that you can use with this unit
The battery that can be used with this unit is DMW-BCF10E.
•Use the dedicated charger and battery.
•The camera has a function for distinguishing batteries which can be used
safely. The dedicated battery (DMW-BCF10E) supports this function. The
only batteries suitable for use with this unit are genuine Panasonic
products and batteries manufactured by other companies and certified by
Panasonic. (Batteries which do not support this function cannot be used).
Panasonic cannot in any way guarantee the quality, performance or safety
of batteries which have been manufactured by other companies and are
not genuine Panasonic products.
∫Charging
•The battery is not charged when the camera is shipped. Charge the battery
before use.
•Charge the battery with the charger indoors.
•It is recommended to charge the battery in a temperature between 10 oC to
35 oC. (The battery temperature should also be the same.)
It has been found that counterfeit battery packs which look very similar
to the genuine product are made available to purchase in some
markets. Some of these battery packs are not adequately protected with
internal protection to meet the requirements of appropriate safety
standards. There is a possibility that these battery packs may lead to
fire or explosion. Please be advised that we are not liable for any
accident or failure occurring as a result of use of a counterfeit battery
pack. To ensure that safe products are used we would recommend that
a genuine Panasonic battery pack is used.
Attach the battery paying
attention to the direction of the
battery.
Connect the AC cable.
•Disconnect the charger from the
electrical socket and detach the battery
after charging is completed.
DMC-FT2&TS2GN-VQT2M46_eng.book 19 ページ ２０１０年２月９日 火曜日 午前８時４６分

VQT2M46 (ENG)
20
∫About the [CHARGE] indicator
•When the [CHARGE] indicator flashes
–The battery temperature is too high or too low. It is recommended to charge
the battery again in an ambient temperature of between 10 ºC to 35 ºC.
–The terminals of the charger or the battery are dirty. In this case, wipe off the
dirt with a dry cloth.
∫Charging time
∫Approximate operating time and number of recordable pictures
Recording conditions by CIPA standard
•CIPA is an abbreviation of [Camera & Imaging Products Association].
•Normal Picture Mode
•Temperature: 23 oC/Humidity: 50% when LCD monitor is on.
•Using a Panasonic SD Memory Card (32 MB).
•Using the supplied battery.
•Starting recording 30 seconds after the camera is turned on. (When the Optical
Image Stabilizer function is set to [AUTO].)
•Recording once every 30 seconds with full flash every second recording.
•Changing the zoom magnification from Tele to Wide or vice versa in every
recording.
•Turning the camera off every 10 recordings and leaving it until the temperature
of the battery decreases.
The [CHARGE]
indicator turns on: The [CHARGE] indicator Ais turned on and
charging will start.
The [CHARGE]
indicator turns off: The [CHARGE] indicator Aof the charger will turn
off once the charging has completed without any
problem.
Charging time Approx. 130 min
Number of recordable pictures Approx. 360 pictures
Recording time Approx. 180 min
Playback time Approx. 300 min
DMC-FT2&TS2GN-VQT2M46_eng.book 20 ページ ２０１０年２月９日 火曜日 午前８時４６分