Panasonic Lumix DMC-F2PC User manual

© Panasonic Corporation 2010 Unauthorized copy-
ing and distribution is a violation of law.
ORDER NO. DSC1003025CE
B26
Digital Camera
Model No. DMC-F2P
DMC-F2PC
DMC-F2PR
DMC-F2PU
DMC-F2EB
DMC-F2EE
DMC-F2EF
DMC-F2EG
DMC-F2EP
DMC-F2GC
DMC-F2GF
DMC-F2GN
Vol. 2
Colour
(S)...........Silver Type (except PC/EF)
(K)...........Black Type
(P)...........Pink Type (except PC/EF)

2
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3
1.4. How to Discharge the Capacitor on Flash Top
P.C.B.----------------------------------------------------------4
2Warning--------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord(For EB/GC) ----------------------6
2.4. How to Replace the Lithium Battery-------------------7
3 Service Navigation------------------------------------------------8
3.1. Introduction --------------------------------------------------8
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------8
3.3. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------9
4 Specifications----------------------------------------------------13
5 Service Fixture & Tools ---------------------------------------14
5.1. When Replacing the Main P.C.B. --------------------14
5.2. Service Position ------------------------------------------14
6 Measurements and Adjustments --------------------------15
7 Maintenance ------------------------------------------------------15
7.1. Cleaning Lens and LCD Panel -----------------------15

3
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 MΩand 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1

4
1.4. How to Discharge the Capacitor on Flash Top P.C.B.
CAUTION:
1. Be sure to discharge the capacitor on FLASH TOP P.C.B..
2. Be careful of the high voltage circuit on FLASH TOP P.C.B. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Install the insulation tube onto the lead part of resistor (ERG5SJ102:1kΩ/5W).
(an equivalent type of resistor may be used.)
3. Place a resistor between both terminals of capacitor on the FLASH TOP P.C.B. for approx. 5 seconds.
4. After discharging, confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1

5
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

6
2.3. Caution for AC Cord
(For EB/GC)
2.3.1. Information for Your Safety
IMPORTANT
Your attention is drawn to the fact that recording of pre-
recorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not expose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.3.2. Caution for AC Mains Lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASTA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2.3.2.1. Important
The wires in this mains lead are coloured in accordance with
the following code:
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the ter-
minal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be con-
nected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
2.3.2.2. Before Use
Remove the Connector Cover as follows.
2.3.2.3. How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue Neutral
Brown Live

7
2.4. How to Replace the Lithium Battery
2.4.1. Replacement Procedure
1. Remove the MAIN P.C.B.. (Refer to Disassembly Procedures.)
2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B9101” at foil side of MAIN P.C.B.)
and remove the Lithium battery together with electric lead terminal. Then replace it into new one.
NOTE:
The Type No. ML421 includes electric lead terminals.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML421 Manufactured by Energy Company, Panasonic Corporation.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for DMC-F2 series, as well.

8
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

9
3.3. How to Define the Model Suffix (NTSC or PAL model)
There are four kinds of DMC-F2, regardless of the colours.
• a) DMC-F2P/PC
• b) DMC-F2EB/EF/EG/EP/GN
• c) DMC-F2EE
• d) DMC-F2PR/PU/GC/GF
What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash-ROM mounted on MAIN P.C.B..
3.3.1. Defining methods:
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.

10
3.3.2. INITIAL SETTINGS:
After replacing the MAIN P.C.B., be sure to perform the initial settings after achieving the adjustment by ordering the following pro-
cedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, be sure to read the following CAUTIONS.
2. PROCEDURES:
• Precautions: Read the above "CAUTION 1" and "CAUTION 2", carefully.
• Preparation:
1. Attach the Battery or AC Adaptor with a DC coupler to the unit.
(Since this unit has built-in memory, it can be performed without inserting SD memory card.)
2. Set the recording mode to the [ NORMAL PICTURE ] mode.
(Press the [ MODE ] button and select the [ NORMAL PICTURE ] by pressing the “[ UP ] and [ DOWN ] of Cursor buttons”,
then press the [ MENU/SET ] button.)
NOTE:
If the unit is other than [ NORMAL PICTURE ] mode, it does not display the initial settings menu.
•Step 1. The temporary cancellation of “INITIAL SETTINGS”:
Set the [ REC ]/[ PLAYBACK ] selector switch to “[ REC ] (Camera mark)”.
While keep pressing “[ UP ] of Cursor button” and [ DISPLAY ] button simultaneously, turn the Power on.
•Step 2. The cancellation of “INITIAL SETTINGS”:
Set the [ REC ]/[ PLAYBACK ] selector switch to “[ PLAYBACK ]”.
Press “[ UP ] of Cursor button” and [ DISPLAY ] button simultaneously, then turn the Power off.
•Step 3. Turn the Power on:
Set the [ REC ]/[ PLAYBACK ] selector switch to “[ REC ] (Camera mark)”, and then turn the Power on.
•Step 4. Display the INITIAL SETTING:
While keep pressing [ MENU/SET ] and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Power off.
The "INITIAL SETTINGS" menu is displayed.
There are two kinds of “INITIAL SETTINGS” menu form as follows:

11
[CASE 1. After replacing MAIN P.C.B.]
When MAIN P.C.B. has just been replaced, all of the model suffix is displayed as follows. (Five pages in total)
[CASE 2. Other than “After replacing MAIN P.C.B.”]
•Step 5. Choose the model suffix in “INITIAL SETTINGS”: (Refer to “CAUTION 1”)
[Caution: After replacing MAIN P.C.B.]
The model suffix can been chosen, JUST ONE TIME.
Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.
Therefore, select the area carefully.
Select the area with pressing “[ UP ] / [ DOWN ] of Cursor buttons”.
•Step 6. Set the model suffix in “INITIAL SETTINGS”:
• Press the “[ RIGHT ] of Cursor buttons”.
• The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation.
(The unit is powered off automatically.)

12
•Step 7. CONFIRMATION:
Confirm the display of “PLEASE SET THE CLOCK” in concernd language when the unit is turned on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
1) As for your reference, major default setting condition is as shown in the following table.
•Default setting (After “INITIAL SETTINGS”)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-F2P NTSC English Month/Date/Year
b) DMC-F2EG PAL English Date/Month/Year
c) DMC-F2PU NTSC English Month/Date/Year
d) DMC-F2GC PAL English Date/Month/Year
e) DMC-F2EF PAL French Date/Month/Year
f) DMC-F2EB PAL English Date/Month/Year
g) DMC-F2EE PAL Russian Date/Month/Year
h) DMC-F2GN PAL English Date/Month/Year
i) DMC-F2PC NTSC English Month/Date/Year
j) DMC-F2PR PAL English Date/Month/Year
k) DMC-F2EP PAL English Date/Month/Year
l) DMC-F2GF PAL English Date/Month/Year

13
4 Specifications

14
5 Service Fixture & Tools
5.1. When Replacing the Main P.C.B.
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.
5.2. Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
CAUTION-1. (When servicing FLASH TOP P.C.B.)
1. Be sure to discharge the capacitor on FLASH TOP P.C.B..
Refer to “HOW TO DISCHARGE THE CAPACITOR ON FLASH TOP P.C.B.”.
The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on FLASH TOP P.C.B..
3. DO NOT allow other parts to touch the high voltage circuit on FLASH TOP P.C.B..
No. Parts No. Connection Form
1 RFKZ0416 FP9001 (MAIN) - CCD UNIT 41PIN 0.3 FFC
2 RFKZ0477 FP9002 (MAIN) - LENS UNIT 45PIN 0.3 FFC
3 RFKZ0418 PP9001 (MAIN) - PS8001 (FLASH TOP) 30PIN B to B

15
6 Measurements and Adjustments
The adjustment details are described in "Service Manual Vol.1" for this model.
When the following part(s) located on the MAIN P.C.B. is replaced, perform the same necessary adjustment items of MAIN P.C.B..
* IC6001 : VENUS
* IC6002 : Flash-Rom
7 Maintenance
7.1. Cleaning Lens and LCD Panel
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.

S-1
S1. About Indication of The Schematic Diagram............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Main P.C.B. ........................................................................... S-2
S3. Block Diagram.......................................................................... S-3
S3.1. System Control Block Diagram ............................................. S-3
S3.2. Video/Audio Process Block Diagram .................................... S-4
S3.3. Sensor Block Diagram .......................................................... S-5
S3.4. Lens Drive Block Diagram..................................................... S-6
S3.5. Power Block Diagram............................................................ S-7
S4. Schematic Diagram.................................................................. S-8
S4.1. Power (P) Schematic Diagram.............................................. S-8
S4.2. Jack (J) Schematic Diagram ............................................... S-12
S4.3. Sensor (SE) Schematic Diagram ........................................ S-13
S4.4. LCD (L) Schematic Diagram ............................................... S-14
S4.5. Digital (D) Schematic Diagram............................................ S-16
S4.6. Gyro (GY) Schematic Diagram ........................................... S-20
S4.7. System Driver (SY) Schematic Diagram.............................S-21
S4.8. Rear Operation (R) Schematic Diagram ............................. S-22
S4.9. Main Connection (MC) Schematic Diagram........................ S-24
S5. Print Circuit Board..................................................................S-28
S5.1. Main P.C.B. ......................................................................... S-28
S5.1.1. Main P.C.B. ...................................................................... S-28
S5.1.2. Main P.C.B. Address Information .....................................S-29
S6. Replacement Parts List..........................................................S-31
Table of contents
Service Manual
DSC1003025CE
Diagrams and Replacement
Parts List
Vol. 2
(S)...........Silver Type (except PC/EF)
Colour
(K)...........Black Type
(P)...........Pink Type (except PC/EF)
Model No.
DMC-F2P
DMC-F2PC
DMC-F2PR
DMC-F2PU
DMC-F2EB
DMC-F2EE
DMC-F2EF
DMC-F2EG
DMC-F2EP
DMC-F2GC
DMC-F2GF
DMC-F2GN
Digital Camera
Name of Signal
OFTR FEP This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice

S-2
S2. Voltage Chart
S2.1. Main P.C.B.
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard.
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
REF No. PIN No. POWER ON
IC1001 1 4.9
IC1001 2 6.4
IC1001 3 5.2
IC1001 4 6.4
IC1001 5 2.2
IC1001 6 0
IC1001 7 1.7
IC1001 8 6.4
IC1001 9 6.9
IC1001 10 6.9
IC1001 11 9.7
IC1001 12 5.2
IC1001 13 4.3
IC1001 14 0
IC1001 15 4.4
IC1001 16 6.4
IC1001 17 0
IC1001 18 4.1
IC1001 19 5.2
IC1001 20 1.2
IC1001 21 1.4
IC1001 22 1.4
IC1001 23 1.4
IC1001 24 0
IC1001 25 0
IC1001 26 0
IC1001 27 1.2
IC1001 28 0
IC1001 29 6.4
IC1001 30 5
IC1001 31 9.7
IC1001 32 4.1
IC1001 33 1.4
IC1001 34 0
IC1001 35 1.7
IC1001 36 1.3
IC1001 37 0.8
IC1001 38 4.9
IC1001 39 6.9
IC1001 40 6.4
IC1001 41 6.9
IC1001 42 3.9
IC1001 43 0
IC1001 44 5.5
IC1210 1 4.9
IC1210 2 0
IC1210 3 4.5
IC1210 4 5.2
IC3002 1 4.8
IC3002 2 0
IC3002 3 4.3
IC3002 4 4.9
Q1040 1 0
Q1040 2 0
Q1040 3 2.6
Q1040 4 0
Q1040 5 0
Q1040 6 4.5
Q1050 1 5.2
Q1050 2 6.4
Q1050 3 -9.2
Q1050 4 0
Q1050 5 0
Q1050 6 0
QR1101 E 0
QR1101 C 0
REF No. PIN No. POWER ON
QR1101 B 6.9

S-3
S3. Block Diagram
S3.1. System Control Block Diagram
FULL
82
98
73
17
12
93
V24
U23
T21
P22
GPI01
AA16
ADC8
GPIO47
IC6001
(VENUS4)
GPIO43
IC6002
(SDRAM/256Mbit, NAND FLASH ROM/512Mbit)
DATA
ADDRESS
A20
L22
Bank Adr.
DATA
ADDRESS
127
105
A11
D13
DATA
34
IC9101
(SYSTEM IC)
SCCS
T5
47
SO
32
SCSI
B9101
Timer
Back UP
BATTERY
Y1
AA2
GPIO44
V4
GPIO42
U3
T4
GPIO49
J2
FLASH TOP P.C.B.
7586
IC9101
(SYSTEM IC)
62 BATT
84
RESETOUT
36
SCSCLK
44
(POWER ON H) (POWER ON L)
(SHUTTER 0)(SHUT HALF)
3
2
4
1
T
W
ON
OFF
1
3
HALF
74
33 (SHUTTER 1) V3
GPIO50 51
(SHUT FULL)
PP9001
23
PS8001
23
PP9001
10
PS8001
10
PP9001
7
PS8001
7
PP9001
6
PS8001
6
PS8001
3
1
4
2
5
6
21
4 3
2 1
4 3
2 1
4 3
2 1
4 3
2 1
4 3
2 1
4 3
2 1
4 3
S9506
LEFT
S9508
MODE
S9505
DOWN
S9504
UP
S9502
MENU/SET
S9503
Q.MENU
S9501
DISPLAY
BA0D
BA1D
DRBA0
DRBA1 Bank Adr.
DQ31D
DQ5D
DRD31
DRD0
A4D
A3D
DRA0
DRA11
CPUD16
CPUD23
I/O3N
I/O4N
P1
J1
K5
S8003
T/W SW
S8002
POWER SW
S8001
SHUTTER SW
PP9001
9,18-21
DATA
CLEN
CEN
3
REN
4
7
6
WEN
13
WPN
RL6008
14
ALEN
16
R/BN
RL6007
RL6009
RL6010
TL8007
CL8011
TL8004
SAFETY GND
ET8003
SLEEVE GND
37
78
B21
DQM3D
DQM0D DRDQM0
33
CKED
52
62
58
72
81
SDRAM AREA/256Mbit
NAND FLASH ROM AREA/512Mbit
RASD
CLKD
CASD
CSD
WED
CL6005
RL6005
RL6003
RL6004
3
SYSCK
G24
DRCKE
G22
H22
L24
G23
F24
DRRASB
DRAMFCK
DRCASB
XDCS
DRWEB
B14
A10
D14
B11
D12
D11
C11
FR CLE
FROM CS
CPUREB
CPUWE2B
FR WP
FR ALE
FR RB
RSTB
P2
GPIO40
AA1
REC
PB
1
3
S8005
REC/PB SW
ADC9 AC16
GPIO56
GPIO57
L5
GPIO61
GPIO60
GPIO62
ADC10
J21
DRDQM3
OSC IN
X9101
(32.768KHz)
OSC OUT
61
63
PP9001
28
D8001
1
LEDOUT2
2
LEDOUT1
AF ASSIST LED
IGBT VCC
PS8001
28
PS8001
27
PP9001
27
(CLK27 SYS)
(SYS RESET)
(S SYSCON CS)
(S SYSCON SI)
(S SYSCON SO)
(S SYSCON SCK)
(TELE WIDE)
(REC/PB MODE)
(UP)
(DOWN)
(DELETE)
(DISPLAY)
(MENU)
(MODE SW)
CL9101
PP9001
17
PS8001
17
RL9102
RL9104
RL9101
RL9103
POWERONH
SHUTTERHALF
SHUTTERFULL
POWERSWONL
SHUTTER0
SHUTTER1
9,18-21
CL9008
(AF LED K)
CL9002
2 1
4 3
S9507
RIGHT
K3
GPIO58 (RIGHT)
K4
GPIO59
(LEFT)
AB15
D9501
POWER LED
D3V
4
LEDOUT0
CL9007 CL9003
CL9004
2
DMC-F2 SYSTEM CONTROL BLOCK DIAGRAM

S-4
IC6002
IC6001
(VENUS4)
M3
N5
M1
N1
DATA
ADDRESS
M5
R3
M4
JK2001
VIDEO OUT 2
USB+ 5
USB- 7
USB CAB IN 8
V21
4
6
7
8
9
1
2
5
10
12
D0
D1
D2
D3
CMD
CLK
C.DET
WP
P6401
(SD CARD CONNECTOR)
W2
LINE OUT 3
M8001
(MIC)
6
PP9001
2
PS8001
2
CL2007
E6
H5
D1
11
PP9001
3
PS8001
3
CL5003
CL5002 SPEAKER
PP9001
25
PS8001
25
PP9001
26
PS8001
26
ET8001
ET8002
CL5001
76
64
89
88
101
LCD
FP9103
27
34
FP9103
FP9103
26
MCU
(SDDAT2)
(SDDAT3)
(SDCMD)
(SDCLK)
(SDCD)
(SDWP)
USB SIGDM
VIDEO OUT
(SDDAT1)
(SDDAT0)
ADC5
GPIO46
INTERNAL BUS CONTROL
GPIO70
LCDOUT7
LCDOUT0
LCDCLK
PRE
PROCESS
BLOCK
YC
PROCESS
BLOCK
JPEG
PROCESS
BLOCK
VIDEO
OUTPUT
BLOCK
FLASH TOP P.C.B.
AB8
CCD0
CCD11
AC8
AD3
FCK
CCDHD
CCDVD
MCK48I
AD9
X6001
(24MHz)
IC9101
(SYSTEM IC)
RESETOUT
CCD
SSG
CCD
CDS,
AGC
A/D
CDS Signal
(12Bit)
SENSOR SECTION
SDRAM AREA/256Mbit NAND FLASH ROM AREA/512Mbit
DATA
12bit 32bit 8bit
A0D A11D DQ0D DQ31D I/O0N I/O7N
DRA0 DRA11 DRD0 DRD31 CPUD16 CPUD23
AB24
AA24
MCK48O
CLK18 LCD
LCDOUT7
LCDOUT0
FP9103
37
LCD CS
FP9103
25
LCDHD
FP9103
24
LCDVD
G3
E1
LCDHD
LCDVD
Y1
V4
GPIO44
GPIO42
FP9103
35
S SYSCON SO
FP9103
36
S SYSCON SCK
AD20
GPIO25
GPIO26
GPIO27
GPIO28
GPIO24
GPIO23
GPIO22
SD CORE
USB I/F
AD11
SDDET IN
CL5006
MIC OUT
AUPWMIN
AD18
P2
RSTB
LINEOUT
99
MICIN
83
SPPOS
79
SPNEG
(SDRAM/256Mbit, NAND FLASH ROM/512Mbit)
G2
USB SIG DP
AD12
(G AUD AD IN)
(AUDIO PWM)
36
4
32
SCSCLK
SCSI
(LCD CS)
(S SYSCON SO)
(S SYSCON SCK)
CL2008
FP9005
9
FP9005
5
FP9005
12
FP9005
13
FP9005
14
FP9005
10
FP9005
11 CABLE DET 1
Y24
(CABLE DET)
GPIO13
(AV OUT / DIGITAL TERMINAL)
CL2001
CL2012
QR6001
(CLK18 LCD)
(G VIDEO OUT)
(G USB - )
(G USB+)
(SYS RESET)
AD10
4
5
6
3
2
1
V22
GPIO19
A3.1V
GPIO12 (USB CAB IN)
(SYG SW)
RL9101
RL9103
FP9103
39
LCD RESET
L1
GPIO2
FP9005
15
SD FPC UNIT
(LCD RESET)
27 V IN 28
V OUT
DMC-F2 VIDEO/AUDIO PROCESS BLOCK DIAGRAM
S3.2. Video/Audio Process Block Diagram

S-5
IC3001
23
24
28
21
(CCD SIGNAL PROCESSOR)
65 CDS
SUBCK
FP9001
36
11
39
FP9001
34
FP9001
39
FP9001
38
FP9001
23
FP9001
11
SUB 21
64 RG
To IC6001-AD8 (AFE CS)
To IC6001-AA11 (AFE SDATA)
To IC6001-AB10 (AFE SCK)
FP9001
37
22
V11B
V4
H1A
H2A
HL
RG
FP9001
18
FP9001
19
FP9001
24
FP9001
26
FP9001
13
FP9001
25
9V5A
10 V5B
14 V1
12 V3
1V9
13 V2
CCD IN
FP9001
10
38 V11A
31
3
FP9001
5
FP9001
15
V9R
V7
FP9001
17
FP9001
14
2V8
8V6
2744pix
3656pix
3672pix
2760pix
V6A
28
V6B
29
V5A
26
V5B
27
V1
22
V15
38
V2
23
V3
24
V4
25
V7
30
V9
32
V11
34
V8
31
63 HL
59 H1
60 H2
61 H3
62 H4
H-DRIVER
V-DRIVER
To IC6001-AD10
(CCDVD)
To IC6001-AD9
(CCDHD)
To IC8001-2 (FLASH TRG)
FP9001
29
29 H1B
30 H2B
VO
18
Q3101
6
PW CCD PLUS
5
4
1
2
3
VDD
17
4FP9001
16
V7S
FP9001
12
FP9001
9
40 V10
37 V12
FP9001
8
FP9001
6
32 V9L
34 V11L
V10
33
V12
35
V13
36
V16
39
V14
37
MSUB
25
FP9001
32 45 VMM
V11B
V4
V5A AFE
V5B
V1 AFE
V3 AFE
V9
V2
V11A
V9R
V7 AFE
V8
V6
V7S
V10
V12
V9L
V11L
FP9001
7
33 V11R V17
40
V11R
(CCD IMAGE SENSOR)
SUBSW
26
FP9001
33 70 GP01
CL3007
G CCDOUT
SUB
G H1
G H2
G HL
G R
SUBSW1
MSUB
CL8004
CL3001
CL3002
PS8001
29
PP9001
29
RL3032
RL3031
RL3030
VGA
INTERNAL
REGISTERS
D0 18
7
72
GP03
D11
CLI 68
TG CORE
HD 4
VD 5
PRECISION
TIMING
GENERATOR
12bit
VREF
REFT 66
REFB 67
CLAMP
12-bit
ADC
3 2 1
SCK SDI SL
To IC6001-AB8 AC8
To IC6001-AD3
(CLK45 FCK)
3
IC3002
(REGULATOR)
VCNT
1VOUT 4
2
VIN
GND
SE3.4V
D3V
6
SYNC/RSTB
CL3003
AFE3.1V
71 GP02
CL3004
5 6
1 2
7 8
3 4
RX3002
FP9001
22
DMC-F2 SENSOR BLOCK DIAGRAM
S3.3. Sensor Block Diagram