Panasonic Lumix DMC-FS5P User manual

© 2008 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.
ORDER NO. DSC0802006CE
B26
Digital Camera
Model No.DMC-FS5P
DMC-FS5PC
DMC-FS5PL
DMC-FS5PR
DMC-FS5E
DMC-FS5EB
DMC-FS5EE
DMC-FS5EF
DMC-FS5EG
DMC-FS5GC
DMC-FS5GK
DMC-FS5GN
DMC-FS5GT
DMC-FS5GJ
Vol. 2
Colour
(S)...........Silver Type
(K)...........Black Type (except PR)
(A)...........Blue Type (only P)
(R)...........Red Type (except PC/PL/PR/EE/GN/GT)

2
TABLE OF CONTENTS PAGE PAGE
1 Safety Precaution-------------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3
1.4. How to Discharge the Capacitor on Flash Top
PCB------------------------------------------------------------4
2Warning--------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord(For EB/GC) ----------------------6
2.4. How to Replace the Lithium Battery-------------------7
3 Service Navigation------------------------------------------------8
3.1. Introduction --------------------------------------------------8
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------8
3.3. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------9
4 Specifications----------------------------------------------------12
5 Service Fixture & Tools ---------------------------------------13
5.1. When Replacing the Main PCB ----------------------13
5.2. Service Position ------------------------------------------13
6 Maintenace--------------------------------------------------------14
6.1. Cleaning Lens and LCD Panel -----------------------14

3
1 Safety Precaution
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These parts are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essen-
tial that these critical parts should be replaced with manu-
facturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from acci-
dents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by acci-
dental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 MΩand 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-
age at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equiva-
lent) may be used to make the hot checks, leakage cur-
rent must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1

4
1.4. How to Discharge the Capacitor on Flash Top PCB
CAUTION:
1. Be sure to discharge the capacitor on FLASH TOP PCB.
2. Be careful of the high voltage circuit on FLASH TOP PCB when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and Remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1kΩ/5W).
(an equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on FLASH TOP PCB for approx. 5 seconds.
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1

5
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

6
2.3. Caution for AC Cord
(For EB/GC)
2.3.1. Information for Your Safety
IMPORTANT
Your attention is drawn to the fact that recording of pre-
recorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not expose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.3.2. Caution for AC Mains Lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASRA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2.3.2.1. Important
The wires in this mains lead are coloured in accordance with
the following code:
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the ter-
minal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be con-
nected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
2.3.2.2. Before Use
Remove the Connector Cover as follows.
2.3.2.3. How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue Neutral
Brown Live

7
2.4. How to Replace the Lithium Battery
2.4.1. Replacement Procedure
1. Remove the MAIN PCB. (Refer to Disassembly Procedures.)
2. Remove the Lithium battery (Ref. No. “B9101” at foil side of MAIN PCB) and then replace it into new one.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML421S/ZT Manufactured by Matsushita Battery Industrial Co.,Ltd.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for DMC-FS5 series, as well.

8
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of PCB Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01K-----------(0.3mm 100g Reel)
RFKZ06D01K-----------(0.6mm 100g Reel)
RFKZ10D01K-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

9
3.3. How to Define the Model Suffix (NTSC or PAL model)
There are five kinds of DMC-FS5, regardless of the colours.
• a) DMC-FS5P/PC
• b) DMC-FS5E/EB/EF/EG/GN
• c) DMC-FS5EE
• d) DMC-FS5GT/GK
• e) DMC-FS5PL/GC/PR/GJ
What is the difference is that the “INITIAL SETTINGS” data which is stored in Flash ROM mounted on Main PCB.
3.3.1. Defining methods:
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN PCB, be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site
in “TSN system”, together with Maintenance software.

10
3.3.2. INITIAL SETTINGS:
When you replace the Main PCB, be sure to perform the initial settings after achieving the adjustment by ordering the following pro-
cedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, be sure to read the following CAUTIONS.
2. PROCEDURES:
• Precautions: Proceed the picture back up from the unit. (Refer to above "CAUTION 2")
• Preparation. Set the Recording mode to "Normal Picture Mode".
Set the [REC]/[PLAYBACK] selector switch to "[REC] (Red camera mark)".
Turn on the power and then press the [MODE] button.
Select the "NORMAL PICTURE MODE" using "[UP] / [DOWN] of Cursor button".
Press [MENU/SET] button, then turn the power off.
•Step 1. The temporary cancellation of initial setting:
Set the [REC]/[PLAYBACK] selector switch to “[ REC ] (Red camera mark)”.
While keep pressing [ E.ZOOM ] and “[ UP ] of Cursor buttons” simultaneously, turn the Power on.
•Step 2. The cancellation of initial setting:
Set the [REC]/[PLAYBACK] selector switch to “[ PALYBACK ]”.
Press [ E.ZOOM ] and “[ UP ] of Cursor buttons” simultaneously, then turn the Power off.
•Step 3. Turn the Power on:
Set the [REC]/[PLAYBACK] selector switch to “[ REC ] (Red camera mark)”, and then turn the Power on.
•Step 4. Display the INITIAL SETTING:
While keep pressing [ MENU ] and “[ RIGHT ] of Cursor buttons” simultaneously, turn the Power off.

11
•Step 5. Set the INITIAL SETTING: (Refer to “CAUTION 1”)
[Caution for befor settings]
Once "NONE(JAPAN)" (Area for Japan) or "P" (Area for Noth America) is selected with "INITIAL SETTINGS", other areas will
not displayed even if "INITIAL SETTINGS" menu is displayed again, thus, the area can not be changed.
Select the area carefully.
Select the area with pressing “[ UP ] / [ DOWN ] of Cursor buttons”, and then press the “[ RIGHT ] of Cursor buttons”.
The only set area is displayed, and then press the “[ RIGHT ] of Cursor buttons” after confirmation.
(The unit is powered off automatically.)
Confirm the display of “PLEASE SET THE CLOCK” in English when the unit is turned on again.
•Step 6. CONFIRMATION:
The display shows “PLEASE SET THE CLOCK” when turn the Power on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)
1) As for your reference Default setting condition is given in the following table.
•Default setting (After “INITIAL SETTINGS”)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-FS5P/PC/PL NTSC English Month/Date/Year
b) DMC-FS5E/EB/EG/GC/GN/PR PAL English Date/Month/Year
c) DMC-FS5EF PAL French Date/Month/Year
d) DMC-FS5EE PAL Russian Date/Month/Year
e) DMC-FS5GK PAL Chinese (simplified) Year/Month/Date
f) DMC-FS5GT NTSC Chinese (traditional) Year/Month/Date
g) DMC-FS5GJ PAL Thai Date/Month/Year

12
4 Specifications

13
5 Service Fixture & Tools
5.1. When Replacing the Main PCB
After replacing the MAIN PCB, be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in
“TSN system”, together with Maintenance software.
5.2. Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
CAUTION-1. (When servicing FLASH TOP PCB)
1. Be sure to discharge the capacitor on FLASH TOP PCB.
Refer to “HOW TO DISCHARGE THE CAPACITOR ON FLASH TOP PCB”.
The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on FLASH TOP PCB.
3. DO NOT allow other parts to touch the high voltage circuit on FLASH TOP PCB.
No. Parts No. Connection Form
1 RFKZ0354 FP9103 (MAIN) - LCD UNIT 37PIN 0.3 FFC
2 VFK1974 FP9004 (MAIN) - LCD UNIT 4PIN 0.5 FFC
3 RFKZ0416 FP9001 (MAIN) - CCD UNIT 41PIN 0.3 FFC
4 RFKZ0477 FP9002 (MAIN) - LENS UNIT 45PIN 0.3 FFC
5 RFKZ0418 PP9001 (MAIN) - PS8001 (FLASH TOP) 30PIN B to B

14
6 Maintenace
6.1. Cleaning Lens and LCD Panel
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.

S-1
S1. About Indication of The Schematic Diagram............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Main P.C.B. ........................................................................... S-2
S3. Block Diagram.......................................................................... S-3
S3.1. System Control Block Diagram ............................................. S-3
S3.2. Video/Audio Process Block Diagram .................................... S-4
S3.3. Sensor Block Diagram .......................................................... S-5
S3.4. Lens Drive Block Diagram..................................................... S-6
S3.5. Power Block Diagram............................................................ S-7
S4. Schematic Diagram.................................................................. S-8
S4.1. Power(P) Schematic Diagram............................................... S-8
S4.2. Jack(J) Schematic Diagram ................................................ S-12
S4.3. Sensor(SE) Schematic Diagram ......................................... S-13
S4.4. LCD(L) Schematic Diagram ................................................ S-14
S4.5. Digital(D) Schematic Diagram............................................. S-16
S4.6. Gyro(GY) Schematic Diagram ............................................ S-20
S4.7. System Driver(SY) Schematic Diagram.............................. S-21
S4.8. Rear Operation(R) Schematic Diagram .............................. S-22
S4.9. Main Connection(MC) Schematic Diagram......................... S-24
S5. Print Circuit Board.................................................................. S-28
S5.1. Main P.C.B. ......................................................................... S-28
S5.1.1. Main P.C.B. ...................................................................... S-28
S5.1.2. Main P.C.B. Address Information ..................................... S-29
S6. Replacement Parts List...........................................................S-31
Table of contents
Service Manual
DSC0802006CE
Diagrams and Replacement
Parts List
Vol. 2
(S)...........Silver Type
Colour
(K)...........Black Type (except PR)
(A)...........Blue Type (only P)
(R)...........Red Type (except PC/PL/PR/EE/GN/GT)
Model No.
DMC-FS5P
DMC-FS5PC
DMC-FS5PL
DMC-FS5PR
DMC-FS5E
DMC-FS5EB
DMC-FS5EE
DMC-FS5EF
DMC-FS5EG
DMC-FS5GC
DMC-FS5GK
DMC-FS5GN
DMC-FS5GT
DMC-FS5GJ
Digital Camera
Name of Signal
OFTR FEP This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice

S-2
S2. Voltage Chart
S2.1. Main P.C.B.
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard.
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
REF No. PIN No. POWER ON
IC1001 1 2.9
IC1001 2 4.2
IC1001 3 3.2
IC1001 4 4.2
IC1001 5 1.7
IC1001 6 0
IC1001 7 1.3
IC1001 8 4.2
IC1001 9 4.2
IC1001 10 4.2
IC1001 11 6.6
IC1001 12 2.6
IC1001 13 2.8
IC1001 14 0
IC1001 15 2.8
IC1001 16 4.2
IC1001 17 0
IC1001 18 2.9
IC1001 19 2.6
IC1001 20 0
IC1001 21 0.2
IC1001 22 0.2
IC1001 23 0.3
IC1001 24 0
IC1001 25 0
IC1001 26 0
IC1001 27 1.2
IC1001 28 0
IC1001 29 4.2
IC1001 30 5.6
IC1001 31 6.7
IC1001 32 3.1
IC1001 33 1.2
IC1001 34 0
IC1001 35 0.3
IC1001 36 0.2
IC1001 37 0.3
IC1001 38 1.6
IC1001 39 4.4
IC1001 40 4.2
IC1001 41 4.4
IC1001 42 4.2
IC1001 43 0
IC1001 44 4
IC1210 1 2.8
IC1210 2 0
IC1210 3 2.1
IC1210 4 2.6
Q1040 1 0
Q1040 2 0
Q1040 3 1.7
Q1040 4 0
Q1040 5 0
Q1040 6 2.9
Q1050 1 3.2
Q1050 2 4.2
Q1050 3 -7.3
Q1050 4 0
Q1050 5 0
Q1050 6 0
QR6001 1 0
QR6001 2 0
QR6001 3 0.1
QR6001 4 3
QR6001 5 2.7
QR6001 6 1.9
REF No.
PIN No. POWER ON
QR7131 1 0
QR7131 2 0
QR7131 3 1.4
QR7131 4 0
QR7131 5 0
QR7131 6 1.4
Q1101 S 0
Q1101 D 0
Q1101 G 3.5
Q1102 E 0
Q1102 C 3.5
Q1102 B 0
QR1101 E 0
QR1101 C 0
QR1101 B 4.2
QR1102 E 0
QR1102 C 3.5
QR1102 B 0

S-3
S3. Block Diagram
S3.1. System Control Block Diagram
FULL
85
101
76
20
25
96
V24
U23
T21
P22
GPI01
AA16
ADC8
GPIO48
IC6001
(VENUS4)
GPIO43
IC6002
(SDRAM/256Mbit, NAND FLASH ROM/512Mbit)
DATA
ADDRESS
A20
L22
Bank Adr.
DATA
ADDRESS
130
108
A11
D13
DATA
34
IC9101
(SYSTEM IC)
SCCS
T5
47
SO
32
SCSI
B9101
Timer
Back UP
BATTERY
Y1
AA2
GPIO44
V4
GPIO42
U3
W1
GPIO49
J2
K4
FLASH TOP P.C.B.
7657
IC9101
(SYSTEM IC)
62 BATT
85
RESET OUT
36
SCSCLK
48
POWERSWONH POWERSWONL
SHUTTER 0SHUTTER HALF
84 RESET IND3V
3
2
4
1
T
W
ON
OFF
1
3
HALF
75
33 SHUTTER 1 V3
GPIO50 51
SHUTTER FULL
PP9001
23
PS8001
23
PP9001
10
PS8001
10
PP9001
7
PS8001
7
PP9001
6
PS8001
6
PS8001
3
1
4
2
5
6
PP9001
17
ADC11
21
4 3
2 1
4 3
2 1
4 3
2 1
4 3
2 1
4 3
2 1
4 3
2 1
4 3
S9506
LEFT
S9507
RIGHT
S9505
DOWN
S9504
UP
S9502
MENU
S9503
DELETE
S9501
DISPLAY
BA0D
BA1D
DRBA0
DRBA1 Bank Adr.
DQ31D
DQ5D
DRD31
DRD0
A5D
A3D
DRA0
DRA11
CPUD16
CPUD23
I/O3N
I/O4N
K3
P1
J1
K5
CL9002
S8003
T/W SW
S8002
POWER SW
S8001
SHUTTER SW
PS8001
17
PP9001
8,9,16
CL9003
DATA
CLEN
CEN
6
REN
7
10
9
WEN
16
WPN
RL6008
17
ALEN
19
R/BN
RL6007
RL6009
RL6010
8,9,16
TL8007
CL8011
TL8004
SAFETY GND
ET8003
SLEEVE GND
40
81
B21
DQM3D
DQM0D DRDQM0
36
CKED
55
65
61
75
84
SDRAM AREA/256Mbit
NAND FLASH ROM AREA/512Mbit
RASD
CLKD
CASD
CSD
WED
CL6005
RL6005
RL6003
RL6004
RL9106
RL9104
3
SYSCK
G24
DRCKE
G22
H22
L24
G23
F24
DRRASB
DRAMFCK
DRCASB
XDCS
DRWEB
B14
A10
D14
B11
D12
D11
E11
FR CLE
FROM CS
CPUREB
CPUWE2B
FR WP
FR ALE
FR RB
RSTB
P2
GPIO40
AA1
2 1
4 3
S8004
E.ZOOM
PP9001
11
PS8001
11
REC
PB
1
3
S8005
REC/PB SW
ADC9
AD16
AC16
GPIO56
GPIO57
GPIO59
AB15 ADC10
L5
GPIO61
GPIO60
GPIO62
GPIO58
2 1
4 3
S9508
MODE
J21
DRDQM3
OSC IN
X9101
(32.768KHz)
OSC OUT
61
63
4LEDOUT0 D9501
POWER LED
D3V
PP9001
28
D8001
1LEDOUT2
2LEDOUT1
AF ASSIST LED
D3V
PS8001
28
PS8001
27
PP9001
27
(CLK27 SYS)
(SYS RESET)
(S SYSCON CS)
(S SYSCON SI)
(S SYSCON SO)
(S SYSCON SCK)
(TELE/WIDE)
(REC PB MODE)
(E ZOOM)
(MODE)
(UP)
(DOWN)
(LEFT)
(DELETE)
(DISPLAY)
(MENU)
(RIGHT)
DMC-FS5 SYSTEM CONTROL BLOCK DIAGRAM

S-4
S3.2. Video/Audio Process Block Diagram
IC6002
IC6001
(VENUS4)
M3
N5
M1
N1
V22
3 5
4
IC2001
(VIDEO OUT)
T2
DATA
ADDRESS
M5
R3
M4 JK2001
(DIGITAL / AV OUT TERMINAL)
VIDEO OUT 2
USB+ 5
USB- 7
USB CAB IN
V21
QR6001
4
5
6
7
9
1
2
5
10
12
D0
D1
D2
D3
CMD
CLK
C.DET
WP
P6401
(SD CARD CONNECTOR)
F4
W2
LINE OUT 3
M 001
(MIC)
LPF
6
PP9001
2
PS 001
2
CL2001
CL200
CL2007
E6
H5
D1
L1
11
PP9001
3
PS 001
3
CL5003
CL5002 SPEAKER
PP9001
25
PS 001
25
PP9001
26
PS 001
26
ET 002
ET 001
CL5001
77
5
9
44
101
LCD
FP9103
16
9
FP9103
FP9103
7
MCU
(SDDAT2)
(SDDAT3)
(SDCMD)
(SDCLK)
SDCD
(SDWP)
USB SIGDM
SIG SW
G VIDEO OUT
GPIO
(SDDAT1)
(SDDAT0)
USB CAB IN
ADC5
GPIO69
GPIO46
INTERNAL BUS CONTROL
GPIO70
LCDOUT7
LCDOUT0
LCDCLK
GPIO2
PRE
PROCESS
BLOCK
YC
PROCESS
BLOCK
JPEG
PROCESS
BLOCK
VIDEO
OUTPUT
BLOCK
FLASH TOP P.C.B.
AB
CCD0
CCD11
AC
AD3
FCK(24.75MHz)
CCDHD
CCDVD
MCK4 I
AD10
AD9
X6001
(24MHz)
IC9101
(SYSTEM IC)
RESETOUT
CCD
SSG
CCD
CDS,
AGC
A/D
CDS Signal
(12Bit)
SENSOR SECTION
SDRAM AREA/256Mbit NAND FLASH ROM AREA/512Mbit
DATA
12bit 32bit bit
A0D A11D DQ0D DQ31D I/O0N I/O7N
DRA0 DRA11 DRD0 DRD31 CPUD16 CPUD23
AB24
AA24
MCK4 O
CLK
D7
D0
FP9103
4
RESET
FP9103
3
LOAD
FP9103
5
LCDHD
FP9103
6
LCDVD
G3
E1
LCDHD
LCDVD
Y1
V4
GPIO44
GPIO42
FP9103
1
S D ATA
FP9103
2
SCLK
AD20
GPIO25
GPIO26
GPIO27
GPIO2
GPIO24
GPIO23
GPIO22
SD CORE
USB I/F
FP9005
11
FP9005
10
FP9005
14
FP9005
13
FP9005
12
FP9005
5
FP9005
15
FP9005
9
AD11
4 3
16
5 2
A3.1V
SDDET IN
CL5006
MIC OUT
AUSEN
AUPWM IN
AD1
P2
RSTB
LINE OUT
99
MIC IN
3
SPPOS
79
SPNEG
(SDRAM/256Mbit, NAND FLASH ROM/512Mbit)
D2
USB SIG DP
AD12
(G AUD AD IN)
(S AUD CS)
(AUDIO PWM)
RL5001
CL2005
4 4
41
4
40
AUS CLKAU S D ATA
(LCD RESET)
(LCD CS)
(S SYSCON SO)
(S SYSCON SCK)
(VIDEO MUTE)
DMC-FS5 VIDEO/AUDIO PROCESS BLOCK DIAGRAM

S-5
S3.3. Sensor Block Diagram
To IC6001-AD3
(CLK45 FCK)
IC3001
SUBSW2
21
22
25
23
19
(CDS/AGC/AD/TG)
65
71
CDS VGA
INTERNAL
REGISTORS
A/D
(12bit)
3 2 1
D0 1
SUBCK
FP9001
36
FP9001
3
10
5
FP9001
34
FP9001
39
FP9001
3
FP9001
23
FP9001
11
7
SUB
72
GP03
SCK SDI SL
D11
GP02
21
64 RG
To IC6001-AD (AFE CS)
To IC6001-AA11 (AFE SDO)
To IC6001-AB10 (AFE SCK)
FP9001
37
20
V7B
V4
H1A
H2A
HL
RG
FP9001
1
FP9001
19
FP9001
24
FP9001
26
FP9001
13
FP9001
25
14 V1A
15 V1B
V5A
11 V3A
1V9
13 V2
CCD IN
CLI 6
FP9001
10
4V7A
30
35
FP9001
5
FP9001
15
V9R
V11
FP9001
17
FP9001
14
2V
6V6
2760pix
3760pix
3776pix
2776pix
V6A
2
V6B
29
V5A
26
V5B
27
V1
22
V15
3
V2
23
V3
24
V4
25
V7
30
V9
32
V11
34
V
31
63 HL
59 H1
60 H2
61 H3
62 H4 H-DRIVER
V-DRIVER V-TIMING
CONTROL To IC6001-AD10 (CCDVD OUT)
To IC6004-AD9 (CCDHD OUT)
HD 4
VD 5
To IC 001-2 (FLASH TRG)
SYNC
GENERATOR
FP9001
29
TIMING
GENERATOR
2 H1B
29 H2B
CL3007
12bit
(CCD0 - CCD11)
VO
17
Q3101
6
PW CCD PLUS 12.0V
5
4
1
2
3
VDD
16
3FP9001
16
V7S
FP9001
12
FP9001
9
36 V10
34 V12
FP9001
FP9001
6
31 V9L
33 V11L
V10
33
V12
35
V13
36
V16
39
V14
37
To IC6001-AB AC
CL3004
MSUB
27
FP9001
32 45 VMM
V7B
V4
V1A
V1B
V5AV5B
V3AV3B
V9
V2
V7A
V9R
V11
V
V6
V7S
V10
V12
V9L
V11L
FP9001
7
32 V11RV17
40
V11R
CL 004
(CCD IMAGE SENSOR)
9V5B
12 V3B
SUBSW1
24
FP9001
33 70 GP01
DMC-FS5 SENSOR BLOCK DIAGRAM

S-6
S3.4. Lens Drive Block Diagram
YPWM
FILTERCCD
M
FOCUS MOTOR
M
M
ZOOM MOTOR
ZOOM ENC
41
42
43
14
15
W4
AB2
Y8
GPIO31
GPIO30
GPIO29
6
18
7
52
13
16
LZCK
LZDI
LZLD
IC9101
(SYSTEM IC)
32
29
30
40
FP9802
34
37
35
38
2
3
M
SHUTTER MOTOR
CD BARREL & FOCUS ENC
GPIO7
1-LED CONT
2-LED CONT
1-ABS
2-ABS
T3
L4
K2
GPIO54
GPIO53
IC6001
(VENUS4)
AB1
31 GPIO39
ED
R4
GPIO3
26
23
22
19
11
10
55
58
MN
MP
AA6
GPIO33
EC1
Y4
GPIO34
EB
AB3
GPIO35
EA
HALL
SENSOR
HALL
SENSOR
OIS UNIT
LENS UNIT
DMP
DMN
YMP
YMN
XMP
XMN
108
111
YPOS
XPOS
FP9802
K1
ZHP
LED CONT
31
18
19
20
21
FP9802
FP9802
FP9802
FP9802
8
12
BMP
BMN
46
38
CMN1
CMP2
49
14
115
113
103
Y2
GPIO37
REFO
FP9802
XDRV-
XDRV+
XHO+
XHO-
YDRV-
YDRV+
YHO+
YHO-
2
1
3
4
T8001
1
4
256
3Q8009
PWMOUT
PP9001
1
PS8001
30
PP9001
29
PS8001
29
AMP
AMN
XHN
XINP
ABS
16
17
CL8004
BATT+
28
27
XFIL
YFIL
106
110
YHN
YINP
8
9
7
5
4
6
23
22
26
24
25
27
XV+
XV-
YV+
YV-
117
XVN
XVP
114
104
YVN
YVP
107
W5
GPIO36
21
XPWM
24
AB14
LENADC4
102
REFI
AA1
3GPIO40
SYSCK
QR7131
321
6 45
PP9001
30
PS8001
1
24
IC8001
(ST TRG AMP)
CL8003
CL8001
J4
FHP
D
S
G
F8001
3
44
45
CL7001
CL7002
S8003
(T/W SW)
ADC8 PS8001
23 3
2
4
1
W
T
PP9001
23
4
5
321
67
8
Q8001
1
2
FLASH
C8003
(For Flash
Charge)
CL8005
TL8002
FLASH TOP P.C.B.
1 5
PP9001
22
PS8001
22
IGBT VCC
VCC
CL8008
LENADC3 13 OUTb
IC7101
(GYRO SENSOR)
10 OUTa
H2
GYRO SW 16 HSCa
W24
GYRO STANBY 8SL
10
11
43
42
CMP1
CMN2
12
13
Y7
GPIO32
EC2 17
RL7007 30 XDA
RL7006 29 YDA
AD13
LENADC0
AD15
LENADC1
MCK48I
X6001
(24MHz)
AB24
AA24
MCK48O
J3
GYRO SW 6HSCb
AC14
AA15
LENADC2
AA16
ADC4
AC17
86
78
N3
GPIO14
PWMIN
F8021
CL8027
72
IC3001
(CDS/AGC/AD/TG)
GP03
3SL
1
2
SCK
SDI
AB10
AFE SCK
AA11
AFE SD0
AD8
AFE CS
FLASH TRG
(ZENC LED CONT)
(FZHP LED CONT)
(G ZENC 1)
(G ZENC 2)
(PWM FA)
(PWM FB)
(PWM IRISA)
(PWM IRISB)
(PWM SHUT)
(CLK27 SYS)
(S DAC CK)
(S DAC DI)
(S DAC LD)
(PWM XOIS)
(PWM YOIS)
(G MREF)
(G XPOS)
(G YPOS)
(STB PWM)
(G GYRO YO)
(G GYRO XO)
(TELE WIDE)
(S AFE CS)
(S AFE SD0)
(S AFE SCK)
(STB CHG LV)
TL8003
1
3
TL8001
2
L8001
IRIS MOTOR
DMC-FS5 LENS DRIVE BLOCK DIAGRAM