Panasonic Lumix DMC-TZ2 User manual

VQT1B83
GN
Before use, please read these instructions completely.
This manual is based on the DMC-TZ3 model. Product illustrations
and screens may vary.
Operating Instructions
Digital Camera
Model No. DMC-TZ2
DMC-TZ3

2 VQT1B83
VQT1B83 3
Dear Customer,
We would like to take this opportunity to
thank you for purchasing this Panasonic
Digital Camera. Please read these
Operating Instructions carefully and keep
them handy for future reference.
Information for Your Safety
WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR PRODUCT
DAMAGE,
• DO NOT EXPOSE THISAPPARATUS
TO RAIN, MOISTURE, DRIPPING
OR SPLASHING AND THAT NO
OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHALL BE
PLACED ON THE APPARATUS.
• USE ONLY THE RECOMMENDED
ACCESSORIES.
• DO NOT REMOVE THE COVER
(OR BACK); THEREARE NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Carefully observe copyright laws.
Recording of pre-recorded tapes or
discs or other published or broadcast
material for purposes other than your
own private use may infringe copyright
laws. Even for the purpose of private
use, recording of certain material may
be restricted.
IF THE POWER CORD OF THIS
EQUIPMENT IS DAMAGED, IT MUST BE
REPLACED WITH AN ELECTRICALLY
APPROVED POWER CORD.
THE SOCKET OUTLET SHALL BE
INSTALLED NEAR THE EQUIPMENT
AND SHALL BE EASILYACCESSIBLE.
CAUTION
Danger of explosion if battery is
incorrectly replaced. Replace only
with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to
the manufacturer’s instructions.
Warning
Risk of fire, explosion and burns. Do
not disassemble, heat above 60 °C or
incinerate.
Product Identification Marking is located
on the bottom of units.
-If you see this symbol-
Information on Disposal in other
Countries outside the European
Union
This symbol is only valid in the
European Union.
If you wish to discard this product,
please contact your local authorities or
dealer and ask for the correct method of
disposal.

4 VQT1B83
VQT1B83 5
The battery is not charged
when the camera is
shipped. Charge the
battery and Set the clock
before use.
When you do not use the
card (optional), you can
record or play back pictures
on the built-in memory
(P.26).
Camera
ON/OFF Switch
Previous Next
Quick start guide
Note
Example screens displayed in this manual are for
DMC-TZ3 model.
Charge the battery
Insert the battery
and the card
Set the mode dial
to
Press the shutter button and
take pictures
To play back the pictures
1. Set the mode dial to .
2. Select the picture
you want to view.
3
1ST DAY
10:00 15.MAR.2007
DMC-TZ2:
About the battery charger
CAUTION!
• DO NOT INSTALL OR PLACE THIS
UNIT INA BOOKCASE, BUILT-IN
CABINET OR INANOTHER
CONFINED SPACE. ENSURE THE
UNIT IS WELL VENTILATED. TO
PREVENT RISK OF ELECTRIC
SHOCK OR FIRE HAZARD DUE
TO OVERHEATING, ENSURE
THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT
THE VENTILATION VENTS.
• DO NOT OBSTRUCT THE UNIT’S
VENTILATION OPENINGS WITH
NEWSPAPERS, TABLECLOTHS,
CURTAINS, AND SIMILAR ITEMS.
• DO NOT PLACE SOURCES OF
NAKED FLAMES, SUCH AS
LIGHTED CANDLES, ON THE UNIT.
• DISPOSE OF BATTERIES IN AN
ENVIRONMENTALLY FRIENDLY
MANNER.

6 VQT1B83
VQT1B83 7
Record, view, save those precious moments.
SD memory card
(Optional)
Zoomed-in pictures
Close-up pictures of people
in distance
[10x optical zoom] (P.27)
Clear pictures
Prevents blurring from shaky hands
[Optical Image Stabilizer] (P.39)
Beautiful pictures
Dark places, moving subjects
[Intelligent ISO] (P.46)
Motion pictures
Capture moving scenes
[Motion Picture Mode] (P.47)
Create photos (still pictures) from your favourite motion
pictures (P.63)
Holiday pictures
Useful features for travel – ‘TRAVEL DATE’ (P.48)
‘WORLD TIME’ (P.49)
‘CLIPBOARD’ (P.58)
Cards may be inserted directly
into devices with SD memory
card slots.
On TV screen
With your printer
Connect directly to easily print pictures at home (P.76)
Use a PictBridge-compatible printer.
At digital photo centre
Give card to shop assistant to print pictures. (P.68)
On computer
Send by e-mail, save to hard disk.
Print out pictures.
With DVD recorder
Save to DVD or hard disk
Save and enjoy your
pictures!
Record View
(Playback) on
large screen
(P.79)
Print
at home, or at
a digital photo centre
(P.68, 76)
(P.24)
Alternatively,
connect with AV
cable (supplied)
Alternatively,
connect with USB
connection cable
(supplied)
Alternatively,
connect with USB
connection cable
(supplied)
Alternatively,
connect with AV
cable (supplied)

8 VQT1B83
VQT1B83 9
Contents
Before use 10 Before use.......................................... 10
Read first (10)
To prevent damage and faults (10)
Standard Accessories....................... 11 Names of parts................................... 12
Mode dial (13)
Preparations 14 Charging battery............................... 14
Inserting battery and card ............... 15 Setting the clock............................... 16 Know the different menus ............... 17 Using menus..................................... 18 Using SETUP menu.......................... 20
Basics 24 Taking pictures ................................. 24
Adjusting the focus (25)
Problems with adjusting focus (25)
Checking remaining battery and memory
capacity (25)
Picture save destination (26)
Taking pictures with zoom............... 27
Taking pictures with SIMPLE MODE 28
Backlight compensation (28)
‘SIMPLE MODE’ menu (29)
Viewing your pictures instantly
(REVIEW)........................................... 30
Viewing your pictures (Play) ........... 31
Deleting pictures .............................. 32
Applications
(Record) 33 Changing recording information
display............................................... 33
Making LCD monitor easier to see.. 34
Taking pictures with self-timer........ 35
Taking pictures with flash................ 36
Taking pictures with exposure
compensation................................... 38
Optical image stabilizer ................... 39
Taking pictures according to the
scene ................................................. 40
Scene types (41)
Avoiding subject blurring
(Intelligent ISO)................................. 46
Taking close-up pictures
(MACRO mode)................................. 46
Taking motion pictures .................... 47
Useful features for travel................. 48
Recording holiday duration
(TRAVEL DATE) (48)
Registering local time at your overseas
destination (WORLD TIME) (49)
Using REC menu .............................. 50
W.BALANCE (50)
SENSITIVITY (51)
ASPECT RATIO (51)
PICT.MODE (52)
PICT.SIZE (52)
QUALITY (53)
AUDIO REC. (53)
METERING MODE (53)
AF MODE (54)
BURST (54)
CONT.AF (55)
AF ASSIST LAMP (56)
SLOW SHUTTER (56)
D.ZOOM (56)
COL. MODE (57)
CLOCK SET (57)
Quick setting (57)
Taking/viewing clipboard pictures
(CLIPBOARD).................................... 58
Taking clipboard pictures (58)
Viewing clipboard pictures (59)
CLIPBOARD menu (60)
Applications
(View pictures) 61 Viewing as list (Multi playback/
Calendar playback)........................... 61
Viewing motion pictures/
pictures with audio........................... 62
Creating still pictures from motion
pictures (DMC-TZ3 only).................. 63
Using PLAY menu............................. 64
DUAL DISPLAY (DMC-TZ3 only) (64)
SLIDE SHOW (64)
FAVORITE (65)
ROTATE DISP./ROTATE (66)
DATE STAMP (66)
DPOF PRINT (68)
PROTECT (69)
AUDIO DUB. (70)
RESIZE (70)
TRIMMING (71)
ASPECT CONV. (72)
COPY (73)
FORMAT (73)
Connecting with
other devices 74 Using with computer........................ 74
Folder and file names on computer (75) Printing.............................................. 76 Viewing on TV screen....................... 79
Others 80 List of LCD monitor displays........... 80
Message displays............................. 82 Q&A Troubleshooting........................ 84 Usage cautions and notes............... 90 Recording picture/time capacity..... 92 Specifications ................................... 94

10 VQT1B83
VQT1B83 11
To prevent damage and faults
Before use
Do a test shot first!
Check first to see if you can take
pictures and record sounds (motion
pictures/pictures with audio)
successfully.
We will not compensate for failed/
lost recording or for direct/indirect
damage.
Panasonic will not provide
compensation even if damage is
caused by faults with camera or card.
Certain pictures cannot be played
back
Pictures edited on a computer
Pictures taken or edited on a different
camera
(Pictures taken or edited on this camera
may also not be able to be played back
on other cameras)
Software on the CD-ROM supplied
The following actions are prohibited:
Making duplicates (copying) for sale or
rent
Copying onto networks
LCD monitor characteristics
Extremely high precision technology is
employed to produce the LCD monitor
screen. However there may be some dark
or bright spots (red, blue or green) on the
screen. This is not a malfunction.
The LCD monitor screen has more than
99.99% effective pixels with a mere
0.01% of the pixels inactive or always lit.
The spots will not be recorded on pictures
on the built-in memory or a card.
Avoid shocks, vibration, and pressure
Avoid exposing the camera to strong
vibration or shock; e.g. dropping or
hitting the camera, or sitting down with
the camera in your pocket.
Do not press the lens or the LCD monitor.
Do not get the camera wet or insert
foreign objects
Do not expose the camera to water,
rain, or seawater.
(If camera gets wet, wipe with a soft,
dry cloth. Wring cloth thoroughly first if
wet with seawater, etc)
Avoid exposing lens and socket to dust
or sand, and do not allow liquids to leak
into gaps around buttons.
Avoid condensation caused by sudden
changes in temperature and humidity
When moving between places of
different temperature or humidity, place
camera into a plastic bag and allow to
adjust to conditions before use.
If the lens clouds up, switch off the
power and leave for about two hours to
allow camera to adjust to conditions.
If the LCD monitor clouds up, wipe with
a soft, dry cloth.
When transporting
Switch off power.
We recommend using a genuine leather
case (DMW-CT3, optional).
Lens
ƔDo not leave in direct sunlight.
ƔIf dirty, clean with soft, dry cloth.
Standard accessories
Cards are optional. You can record or play
back pictures on the built-in memory when
you are not using a card. (P.26)
Consult the dealer or your nearest
servicentre if you lose the supplied
accessories. (You can purchase the
accessories separately.)
SDHC memory cards
New standards set in 2006 by SD
Association for high-capacity memory cards
exceeding 2GB.
Can be used on SDHC memory card-
compatible devices, but not on devices only
compatible with SD memory cards.
(referred to in this manual as ‘battery’)
Battery Pack
CGA-S007E
(P. 14)
(referred to in this manual as ‘charger’)
Battery Charger
DE-A46A
(P. 14)
AC Cable
K2CJ2DA00008
(P. 14)
Strap
VFC4090
(P. 12)
USB Connection
Cable
K1HA08CD0007
(P. 74, 76)
AV Cable
K1HA08CD0008
(P. 79)
CD-ROM
Part numbers are as of January 2007
Read first
Battery Carrying
Case
VYQ3680
(P. 91)
The following software on the CD-ROM
is referred to in this manual as ‘supplied
software’.
LUMIX Simple Viewer
PHOTOfunSTUDIO -viewer-

Mode dial
NORMAL PICTURE
12 VQT1B83
VQT1B83 13
Camera ON/OFF switch
(P.18)
Optical image stabilizer
button (P.39)
Lens barrel
Self-timer
indicator
(P.35)/AF
assist lamp
(P.56)
Release lever (P.15)
Names of parts
Speaker (P.22)
Microphone
(P.47, 53, 70)
Status indicator (P.15, 24)
DISPLAY/LCD MODE
button (P.33, 34)
FUNC (Quick setting P.57)/
delete (P.32) button
NORMAL PICTURE mode
Take pictures (P.24).
INTELLIGENT ISO mode
Take pictures according to motion
and brightness of subject (P.46).
PLAYBACK mode
View/edit pictures previously
taken (P.31, 61)
SIMPLE MODE
For beginners (P.28).
Tripod receptacle
Card/Battery door (P.15)
DIGITAL/AV OUT socket
(P.74, 76, 79)
DC IN socket (P.74, 76)
Always use a genuine Panasonic
AC adaptor (DMW-AC5G: optional).
LCD monitor
ƔChecking remaining battery/
memory capacity, etc (P.25)
ƔChanging display (P.33)
ƔDisplay contents list (P.80)
Align to correct mode
(Displayed on screen when
mode changed)
SCENE mode
Take pictures according to scene
(P.40).
CLIPBOARD mode
Take/view pictures as memos
(P.58).
PRINT mode
Print (P.76).
MOTION PICTURE mode
Take motion pictures (P.47).
MACRO mode
Take close-up pictures (P.46).
8SŸ
GRZQź
ULJKWŹŻOHIW
In this manual, direction buttons
to be pressed will be shown in
ZKLWHRUZLWKŸźŻŹ
Self-timer (P.35) ƔExposure
compensation (P.38)
ƔAuto bracket (P.38)
ƔWhite balance fine
adjustment (P.50)
ƔBacklight
compensation (P.28)
ƔFlash (P.36)
ƔMENU/SET
(menu display/set) (P.18)
View previously
taken picture
immediately
(Review) (P.30) DMC-TZ3 only
Strap eyelet
Strap
(supplied)
Shutter button (P.24)
Zoom lever (P.27)
Flash (P.36)
Lens (P.10)
Up/down/left/right
selection

14 VQT1B83
VQT1B83 15
Preparations 2Inserting battery and card
Preparations 1Charging battery
Always charge before first use! (not sold pre-charged)
Note
Battery will be warm during charging and for some time thereafter.
Battery will run out if not used for long periods of time, even after being charged.
Charge the battery with the charger indoors (10 °C-35 °C).
Do not disassemble or modify the charger.
Please purchase a new battery if battery life becomes significantly reduced.
The battery charger is in the standby condition when the AC power supply cord is connected.
The primary circuit is always "live" as long as the power cord is connected to an
electrical outlet.
Battery can be topped up even if not fully depleted.
Battery (model-specific)
Charging light (CHARGE)
On: Charging in progress (approx. 120 min.)
Off: Charging complete
If light is flashing…
Ɣ%DWWHU\WHPSHUDWXUHLVWRRKLJKWRRORZĺ
Battery may still be charged, but it will
take longer as it must adjust to the room
temperature.
Ɣ%DWWHU\FKDUJHUFRQQHFWRULVGLUW\ĺ
clean with dry cloth.
Approximate battery life
Number of pictures:
270 [300 2](at 30-sec intervals) 1(equivalent to approx. 135 [150 2] mins)
1Values based on CIPA standards. (P.91)
(Number reduced if intervals longer – 67 [75 2] pictures if 2-minute intervals)
Playback time: Approx. 260 [280 2] mins
Above figures may be reduced if intervals between recording are longer; if flash, zoom,
or POWER LCD are used frequently; or in colder climates (depends on actual usage).
2DMC-TZ2
Battery
(check orientation)
Card
(check orientation)
Do not touch
connector
Caution
Always use genuine Panasonic batteries.
If you use other batteries, we cannot guarantee the quality of this product.
Do not remove card or battery while power is ‘ON’ or while status indicator is on
(Camera may cease operating correctly, or card/recorded contents may be damaged).
The reading/writing speed of a MultiMediaCard is slower than an SD memory card.
When a MultiMediaCard is used, the performance of certain features may be slightly
slower than advertised.
Keep the Memory Card out of reach of children to prevent swallowing.
Compatible memory cards (optional)
The following SD standard-based cards (Panasonic brand
recommended)
ƔSD memory cards, 8MB-2GB
Ɣ6'+&PHPRU\FDUGV*%ĺ3
(4GB (or greater) cards without the SDHC logo are not of SD
standard.)
ĺ)RUUHFRUGLQJSLFWXUHWLPHFDSDFLW\VHH3
ĺ)RUPRGHOQXPEHUVDQGW\SHV
see http://panasonic.co.jp/pavc/global/cs (This Site is English only.)
MultiMediaCards (still images only)
Set the camera ON/OFF switch to
OFF
Slide to the ‘OPEN’ position and
open the lid
Completely insert battery and card
(both click into place)
Close lid
Slide to the ‘LOCK’ position.
To remove
To remove battery,
move lever in direction
of arrow.
lever
Insert the battery terminals
and attach the battery to the
charger
Ensure ‘LUMIX’ faces outwards.
Connect the AC cable
The AC cable
does not fit
entirely into the
AC input terminal.
A gap will remain as shown
right.
Detach the battery after
charging is complete
After charging is completed, be
sure to disconnect the AC cable
from the electrical outlet.
Charger (model-specific)
To remove card,
press down in centre.
Status indicator
SDHC logo
SDHC memory
card
OPEN
LOCK

16 VQT1B83
VQT1B83 17
Preparations 3Setting the clock
Preparations 4Know the different menus
to get more out of your camera
While this message is displayed
Press
Adjust year, month, date, time
Select
Adjust
Set
Press
Turn on power again and check time
display.
Note
Failure to set the clock will mean
correct date will not be printed
(P.76) when printing pictures in
digital photo centre or when using
DATE STAMP (P.66).
Time is displayed in 24-hour
format. Year can be set between
2000 and 2099.
Clock settings will be saved for
approx. 3 months even after
battery is removed, provided a
fully-charged battery was installed
in camera for the 24 hours
beforehand.
To change time setting
Select ‘CLOCK SET’ from SETUP
menu (P.18), perform and above,
and press .
To set local time at overseas
destination
‘WORLD TIME’ (P.49)
Set mode dial (P.13) to NORMAL PICTURE mode before turning on power.
‘PLEASE SET THE CLOCK’will be displayed when power is turned on for the first time. This camera contains a range of menus to enable you to set your photography and
playback preferences, and to make the camera easier and more fun to use.
The ‘SETUP’ menu in particular contains important functions, such as for time and power
source. Please check these settings before use.
Making the camera more convenient to use (SETUP menu) (P.20)
1/4
SELECT
CLOCK SET
SETUP
WORLD TIME
MONITOR
± 0
OFF
EXIT
GUIDE LINE
TRAVEL DATE
Make settings for ease of use such as adjusting the clock
and changing the beep sounds.
Applicable modes (P.13):
Changing photography preferences (REC menu) (P.50)
1/3
REC
SENSITIVITY
ASPECT RATIO
PICT.SIZE
QUALITY
W.BALANCE
AUTO
SELECT EXIT
AWB
Make settings such as white balance, sensitivity, aspect
ratio, and picture size.
Applicable modes (P.13):
(Screen example: DMC-TZ3)
Using your pictures (PLAY menu) (P.64)
FAVORITE
OFF
PLAY
1/3
ON
SELECT EXIT
ROTATE
SLIDE SHOW
DUAL DISPLAY
ROTATE DISP.
Make settings for using the pictures you have taken,
including rotating, protecting, trimming, and handy settings
for printing your pictures (DPOF).
Applicable modes (P.13):
(Screen example: DMC-TZ3)
The following menus are also included:
To make photography settings to fit certain scenes, e.g. night
 ĺ6&(1(PHQX(P.40)
To easily change settings such as picture quality, for beginners
 ĺ6,03/(02'(PHQX(P.29)
2007
000
MDY
:
JAN
.
1.
SETSELECT SET
CLOCK SET
CANCEL
Select to change
date format
Power

1/4
CLOCK SET
SETUP
WORLD TIME
MONITOR
± 0
OFF
EXITSELECT
GUIDE LINE
TRAVEL DATE
1/3
SENSITIVITY
ASPECT RATIO
PICT.SIZE
QUALITY
W.BALANCE
REC
AWB
AUTO
EXITSELECT
1/4
SELECT
CLOCK SET
SETUP
WORLD TIME
MONITOR
± 0
OFF
EXIT
GUIDE LINE
TRAVEL DATE
2/4
SETUP
ECONOMY
ZOOM RESUME
AUTO REVIEW
OFF
OFF
SELECT SET
5MIN.
1SEC.
BEEP
OFF
1MIN.
2MIN.
5MIN.
10MIN.
POWER SAVE
2/4
SETUP
ECONOMY
ZOOM RESUME
AUTO REVIEW
OFF
OFF
SELECT SET
5MIN.
1SEC.
BEEP
POWER SAVE
OFF
1MIN.
2MIN.
5MIN.
10MIN.
2/4
SELECT
SETUP
EXIT
ECONOMY
ZOOM RESUME
POWER SAVE
AUTO REVIEW
OFF
OFF
BEEP
2MIN.
1SEC.
2/4
SELECT
SETUP
EXIT
ECONOMY
ZOOM RESUME
POWER SAVE
AUTO REVIEW
5MIN.
OFF
1SEC.
OFF
BEEP
1/4
WORLD TIME
MONITOR
± 0
CLOCK SET
SETUP
GUIDE LINE
TRAVEL DATE
OFF
SELECT EXIT
18 VQT1B83
VQT1B83 19
Preparations 5Using menus Explanation of settings method for SETUP menu, REC menu, and PLAY menu.
(Screen example: DMC-TZ3)
Here is explained an example of changing the ‘POWER SAVE’ setting from ‘5 MIN.’ to ‘2
MIN.’ from SETUP menu.
(‘POWER SAVE’ is a function to extend battery life by automatically turning the camera
off if no operations are performed for a certain period.)
Turn on the power
Zoom lever
MENU/SET
Set to
Bring up the menu
Select SETUP menu
Note
7RUHVWRUHGHIDXOWVHWWLQJVĺµ5(6(7¶3
For certain items, there may be no settings selection (step ) (e.g. ‘ROTATE’ on PLAY
menu), or actual display may differ from that above (e.g. ‘WORLD TIME’on SETUP
menu).
Move across to the items
Select the correct item
Select this item
Select this setting
Select Select
Highlight ‘CLOCK SET’
3UHVVźDQGPRYHEH\RQGWKH
bottom item Move down to ‘POWER SAVE’
Page 2 displayed
Displays settings Highlight ‘2 MIN.’
Finish
Press
First page of three currently
displayed. (Zoom lever can be
used to scroll through pages.)
1/3
REC
SENSITIVITY
ASPECT RATIO
PICT.SIZE
QUALITY
W.BALANCE
AUTO
SELECT EXIT
AWB
REC menu is displayed.
SETUP menu
Applicable modes:
REC menu
Applicable modes:
PLAY menu
Applicable modes:

20 VQT1B83
VQT1B83 21
Preparations 6Using SETUP menu Make general camera settings such as adjusting the clock, extending the battery
life, and changing the beep sounds. 6HWWLQJVPHWKRGĺ3
Default setting outlined:
Item Uses, operations Settings, notes
CLOCK SET 1, 2 Set the date and time. Set the date/month/year and time (P.16).
WORLD TIME 1, 2 Set the local time at an overseas destination (P.49) (DESTINATION) / (HOME)
MONITOR 1, 2 Adjust the brightness of the LCD monitor (7 levels). -3 · ·
±0 · · +3
GUIDE LINE Change the pattern of the guide lines displayed when taking
pictures.
Display recording information or histogram together with guide
lines (P.33).
Recording information: OFF / ON Histogram: OFF / ON PATTERN: /
‘PATTERN’ cannot be selected in CLIPBOARD mode (P.58). Recording information and
histogram cannot be displayed.
Not displayed in SIMPLE MODE.
TRAVEL DATE
1, 2 Record the number of days elapsed in your travels.
OFF / SET (P.48)
AUTO REVIEW Automatically display pictures immediately after taking
them.
Select display time (seconds).
‘ZOOM’ is useful for checking focus.
OFF / 1SEC. / 3SEC. / ZOOM 3 (displays for 1 second, then at 4x zoom for 1
second)
In ‘SELF PORTRAIT’ scene mode (P.42), ‘AUTO BRACKET’ 3 (P.38), ‘BURST’ mode
(P.54), or pictures with audio (P.53, 70), auto review performed regardless of setting.
Motion pictures cannot be automatically reviewed.
POWER SAVE Automatically shut off power while not in use.
(Saves battery consumption)
To restore: Press the shutter button halfway, or turn on the
power again.
OFF / 1 MIN. / 2 MIN. / 5 MIN. / 10MIN. (Set time before POWER SAVE is initiated)
Cannot be used in the following cases:
When using AC adaptor (DMW-AC5G, optional), when connected to computer/printer,
during motion picture recording/playback, during slideshows (exception: set to 10
minutes while slideshow is paused and during ‘MANUAL’ slideshows)
Setting fixed to ‘2 MIN.’ in ‘ECONOMY’, and to ‘5 MIN.’in SIMPLE MODE (P.28) and
CLIPBOARD (P.58).
ZOOM RESUME
1, 2 Remember the zoom ratio when turning power off.
OFF / ON Focus position cannot be stored.
Released and cannot be set when using ‘SELF PORTRAIT’ scene mode.
ECONOMY
Restrict battery consumption when recording.
(Dims LCD monitor, automatically shuts off monitor when not
in use.)
Monitor also shut off during flash battery charging.
Status indicator is illuminated while monitor is off.
To restore: Press any button.
OFF / LEVEL 1 (turned off after approx. 15 seconds of inactivity)/LEVEL 2 (turned off
after approx. 15 seconds, or approx. 5 seconds of inactivity after recording)
Cannot be used in the following cases:
When using SIMPLE MODE, CLIPBOARD mode ,or AC adaptor (DMW-AC5G,
optional), when menu screen is displayed, when using self-timer setting or during
motion picture recording.
LCD monitor not dimmed when using ‘POWER LCD’ or ‘HIGHANGLE’ (P.34).
‘CLOCK SET’, ‘AUTO REVIEW’, ‘POWER SAVE’ and ‘ECONOMY’ are important for
clock setting and battery life. Be sure to check these before use. 1 Settings also reflected in SIMPLE MODE (P.28).
2 Settings also reflected in CLIPBOARD mode (P.58).
3 DMC-TZ3 only.

22 VQT1B83
VQT1B83 23
Preparations 6Using SETUP menu (Continued) Default setting outlined:
Item Uses, operations Settings, notes
BEEP 1, 2 Change or mute beep sounds. Volume: (mute) / (low) / (high) Tone: / /
SHUTTER 1, 2 Change or mute shutter sounds. Volume: (mute) / (low) / (high) Tone: / /
VOLUME 2Adjust volume of sound from speakers (7 levels). 0 · ·
LEVEL3 · · LEVEL6
Cannot be used to adjust TV speaker volume when connected to TV.
NO. RESET 1Reset image file numbers and start again from ‘0001’.
File numbers and folder numbers (P.75)
YES/NO
Numbers cannot be reset once folder number reaches 999. In this case, save all
necessary pictures to your computer, and format the built-in memory/card. (P.73)
To reset folder number to 100:
First, format (P.73) the built-in memory or card, and reset the file numbers using NO.
RESET. Then, select ‘YES’ on the folder number reset screen.
RESET 2Reset SETUP menu (P.20) and REC menu items (P.50) to
their default settings.
RESET REC. SETTINGS? (YES/NO) RESET SETUP PARAMETERS? (YES/NO)
Resetting SETUP parameters causes the following to be reset: Birthdays in BABY
(P.42) and PET modes (P.44), ‘TRAVEL DATE’ (P.48), ‘WORLD TIME’ (P.49), ‘ZOOM
RESUME’ (P.20), ‘FAVORITE’ in PLAY menu (set to ‘OFF’) (P.65), ‘ROTATE DISP.’ (set
to ‘ON’) (P.66), CLIPBOARD menu (INITIAL DISP.) (set to ‘OFF’) (P.60)
(Only ‘BEEP’ is reset in the SIMPLE MODE menu.)
Folder numbers and clock settings will not be reset.
VIDEO OUT Change the video output format when connected to a TV, etc.
(PLAYBACK mode only) NTSC /
PAL
TV ASPECT Change the aspect ratio when connected to a TV, etc
(PLAYBACK mode only). /
When set to , pictures will be displayed vertically long on LCD monitor when
connecting AV cable (supplied) (P.79).
SCENE MENU Display scene menu when mode dial is set to SCN1 or SCN2. OFF (use previously selected scene mode) /
AUTO (displays scene menu)
To display scene menu when set to ‘OFF’: Press ‘MENU/SET’.
DIAL DISPLAY 1, 2 Display mode dial operation on screen. OFF /
ON (display)
LANGUAGE 1, 2 Change display language.
ENGLISH / DEUTSCH (German) / FRANÇAIS (French) / ESPAÑOL (Spanish) /
ITALIANO (Italian) / 日本語 (Japanese)
1 Settings also reflected in SIMPLE MODE (P.28).
2 Settings also reflected in CLIPBOARD mode (P.58).

F3.3 1/30
NORMAL PICTURE
F3.3 1/30 F3.3 1/30
300
24 VQT1B83
VQT1B83 25
Basics 1Taking pictures Please set the clock before taking pictures (P.16).
Display on screen
Turn on the power
Adjust the focus
Take a picture
Press halfway
Take care not to shake the
camera.
Press fully
Holding the camera
When set to maximum W (1x):
Distance of at least 50 cm from
subject
Vertically ƔDo not block the flash or the lamp
(P.12). Do not look at them from close
range.
ƔDo not touch the lens.
ƔStand with your arms close to your
body and with your legs apart.
When set to maximum T
(maximum zoom): Distance of at
least 2 m from subject
Press the shutter button halfway, ensuring that the subject is aligned with the AF area.
Focus display
Shutter speedAperture
value
Focus In focus Not in focus
Focus display On Flashing
AF area Green Red/white
Sound Double beep Multiple beep
Images outside of the focus range may
not be in full focus even if the light
remains on.
Remaining battery
(Status indicator flashes when LCD monitor is off)
Recharge or replace battery (P.14).
Not displayed when using AC adaptor (DMW-AC5G,
optional).
(flashes red)
Horizontally
Flash Lamp
Zoom lever
AF area (normal)
AF area (when dark or
using digital zoom)
Adjusting the focus
Checking remaining battery and memory capacity
Zoom lever
When (jitter alert) is displayed
Use the Optical image stabilizer (P.39), a tripod, or the self-timer (P.35).
Focus range7RWDNHSLFWXUHVIURPFORVHUDQJHĺ3
,IUHG&RXOGQRWDFKLHYHRSWLPDOH[SRVXUHĺ8VHIODVK3RUFKDQJHµ6(16,7,9,7<¶
(P.51).)
Status indicator illuminated for
approx. 1 second.
Status indicator
To use flash (P.36)
Hold down
halfway
Readjust focus if not correctly adjusted initially.
Subjects/environments which may make focusing difficult:
ƔFast-moving or extremely bright objects, or objects with no colour contrast
ƔTaking pictures through glass or near objects emitting light. In dark, or with significant
jitter.
ƔWhen too close to object or when taking pictures of both distant and close objects
together in the same picture
Problems with adjusting focus (subject not in centre, etc)
Set to (NORMAL PICTURE mode)
Hold down
halfway
First adjust focus
according to subject Return to desired
composition
Press fully
Pictures remaining

300
26 VQT1B83
VQT1B83 27
Pictures may be copied between cards and the built-in memory (P.73).
It is recommended that you copy important pictures to your computer (as
electromagnetic waves, static electricity, or faults may cause data to be damaged).
Cards
Always format (P.73) cards in this camera before first use.
If the switch on the card is set to ‘LOCK’, operations such
as formatting, copying, and deleting cannot be performed.
&RPSDWLEOHPHPRU\FDUGVĺ3
 5HFRUGLQJSLFWXUHWLPHFDSDFLW\ĺ3
Built-in memory (approx. 12.7 MB)
Used as a temporary save destination when you have no card.
May take longer to access than cards.
Clipboard pictures (P.58) are saved to built-in memory.
Recording picture capacity estimates (default settings)
Save destination Built-in memory memory card (Example)
12.7 MB 256 MB 512 MB 1 GB 2 GB
Pictures (DMC-TZ3) 2 68 135 270 550
Pictures (DMC-TZ2) 3 81 160 320 660
The number of pictures that may be recorded varies greatly according - to aspect settings
(P.51), picture size (P.52), and quality (P.53) settings, in addition to the capacity of the
card. (For more details: P.92)
Basics 1Taking pictures(Continued)
Basics 2
Taking pictures with zoom
Subjects can be enlarged by ten times with ‘Optical zoom’ and up to 15 (13.8 ) times with
‘Extra optical zoom’. ‘Digital zoom’ can then be used to multiply this effect by four times
further. (28-280 mm: 35 mm film camera equivalent)
Zoom types
Type Optical zoom Extra optical zoom (EZ) Digital zoom
Max.
enlargement 10x 15x 1, 13.8x 2, 13x 1
12.6x 1, 12x, 11.6x 2 40x (including optical zoom: 10x)
60x
(including extra optical zoom: 15x)
Picture quality No loss No loss Deteriorates by factor of enlargement
Conditions None Select picture size
(P.52) marked with ‘D. ZOOM’ (P.56) set to ‘ON’ in REC
menu
Screen display displayed
Displays digital zoom area
Within digital zoom area AF area
becomes larger when pressing
shutter button halfway
1DMC-TZ3 only, 2DMC-TZ2 only (Zoom ratio depends onASPECT RATIO and PICT.SIZE.)
What is Extra optical zoom (EZ)?
If, for example, set to ‘3M EZ’ (equivalent to 3 million pixels), a picture will only be taken
of a 3M-sized central part of a 7M (equivalent to 7.2 million pixels) 3 area, meaning that
the picture can be enlarged further.
Entering digital zoom area
Once the bar stops before the digital zoom
area, continue to hold the zoom lever, or
release it once then push it again.
To recall zoom ratio from time power was turned off ‘ZOOM RESUME’ (P.20)
Enlarge (Tele) Restore (Wide)
Turn to W sideTurn to T side
The enlargement ratio displayed in the bar on screen is an estimate.
Adjust the focus after adjusting the zoom.
Do not block the lens barrel (P.12) movement while zooming.
Zoom cannot be adjusted during motion picture recording.
A greater degree of distortion may be generated by taking wider-angled pictures of
close objects, while using more telescopic zoom may result in more colouring appearing
around the outlines of objects.
The camera may make a rattling noise and vibrate when the zoom lever is operated – this
is
not a fault.
When using extra optical zoom, zoom movement may stop momentarily near maxim um
W (1x), but this is not a fault.
The Optical image stabilizer may be less effective when using digital zoom. It is
recommended that you use a tripod and the self-timer (P.35).
Picture save destination
Pictures will be saved to a card if one is inserted, or to the built-in memory if not.
This means that an operation is in progress, such as the
recording, reading, or deleting of pictures. Do not turn off the
power or remove the battery, card, or AC adaptor (DMW-
AC5G, optional) (this may cause damage to or loss of data).
Card
Built-in memory
Card Built-in memory
When in operation
are Illuminated red.
Bar stops momentarily
Digital zoom area
DMC-TZ2
Switch (LOCK)
3 DMC-TZ2: 6M

3
BACKLIGHT
28 VQT1B83
VQT1B83 29
Basics 3Taking pictures with SIMPLE
MODE This mode is designed for beginners to easily take pictures.
Only major functions and menu items are displayed.
The settings for the following functions are
fixed. Item Setting
SELFTIMER (P.35) OFF/10 SEC.
POWER SAVE (P.20) 5 MIN.
STABILIZER (P.39) MODE1
W.BALANCE (P.50) AWB
SENSITIVITY (P.51) 1
METERING MODE (P.53)
AF MODE (P.54)
AF ASSIST LAMP (P.56) ON
COL.MODE (P.57) STANDARD
1Same as with ISO LIMIT ‘800’ setting in
Intelligent ISO mode (P.46).
Prevents subjects being dark when background is light.
7RFDQFHOFRPSHQVDWLRQ3UHVVŸDJDLQ
Using flash (FORCED FLASH ON) is recommended
(P.36)
Adjust using ‘EXPOSURE’ (P.38), except for in SIMPLE
MODE.
Displayed when compensation is on.
Default setting outlined:
Item Setting
PICT.MODE
ENLARGE (4:3, 7M 1, Fine):
for printing to 8”x10”size, letter size etc.
4”x6”/10x15cm 2 (3:2, 2.5M EZ, Standard):
for printing regular sizes.
E-MAIL 2 (4:3, 0.3M EZ, Standard):
for attaching to emails or using in homepage.
AUTO REVIEW OFF / ON:
Displays picture for approx. 1 second after taking
BEEP 3 OFF / LOW / HIGH
CLOCK SET 3 Change the date and time (P.16)
1 6M for DMC-TZ2 model. 2 Extra optical zoom (P.27) available.
3 Settings changes reflected in other modes.
Flash can be set to ‘AUTO/RED-EYE’ or ‘FORCED OFF’ (‘FORCED FLASH ON’ or
‘FORCED OFF’ when using backlight compensation).
Recording picture capacity (P.92)
MENU/SET
Backlight compensation
Set to
Adjust the focus
Press halfway
Take a picture
Press fully
The following functions cannot be used.
Item
BURST mode (P.54)
Digital zoom (P.27)
Exposure compensation/AUTO BRACKET
2
(P.38)
White balance fine adjustment (P.50)
AUDIO REC. (P.53)
CONT.AF (P.55)
ECONOMY (P.20)
HIGH ANGLE (P.34)
GUIDE LINE (P.33)
2 DMC-TZ3 only
Green when
focus aligned
Backlight compensation (SIMPLE MODE only)
‘SIMPLE MODE’ menu
Use the menu to change settings such as picture quality and beep sounds.
Press Max. T: Distance of at least 1 m from subject
(displayed)
(2 m unless max.T)
Max. W: Distance of at least 5 cm
from subject
Zoom lever
Focus range
Display SIMPLE MODE
menu Select desired item
(Screen shows beep setting change)
SIMPLE MODE
BEEP
CLOCK SET
AUTO REVIEW
EXITSELECT
PICT.MODE
SIMPLE MODE
CLOCK SET
AUTO REVIEW
SELECT SET
PICT.MODE
BEEP OFF
LOW
HIGH
Select desired setting Finish
SIMPLE MODE
CLOCK SET
AUTO REVIEW
SELECT SET
PICT.MODE
BEEP OFF
LOW
HIGH

Deleting instantly
SET
DELETE SINGLE
DELETE THIS PICTURE?
NO
YES
SELECT MULTI/ALL
1/3
100-0001
10:00 15.MAR.2007
2X
4X
CANCEL
DELETE
30 VQT1B83
VQT1B83 31
Basics 4Viewing your pictures instantly
(REVIEW)
Pictures can be checked while still in a recording mode ( ).
Note
Deleted pictures cannot be recovered.
Motion pictures cannot be reviewed in this way. View in PLAYBACK mode (P.62).
Display picture
4X DELETE
REVIEW1X
EXIT
Most recently taken picture will be
displayed for about 10 seconds.
7RFORVH3UHVVźRUSUHVVWKHVKXWWHU
button halfway.
7RYLHZSUHYLRXVQH[WSLFWXUHŻŹ
Enlarge picture (4x/8x)
Turn to
T side
1X 8X
REVIEW4X
DELETE
Current zoom position (displayed
for 1 sec.)
Picture is enlarged as you turn zoom lever
towards T.
To reduce zoom: Turn lever towards W
side.
7RPRYH]RRPSRVLWLRQŸźŻŹ
To display portrait pictures vertically
(P.66)
While picture is
displayed
Select ‘YES’
Highlight ‘YES’ in orange
To delete several or all
(P.32)
Basics 5Viewing your pictures (Play)
Holding down increases the picture scroll rate.
Cannot be used when using ‘REVIEW’ (P.30) or
‘Multi playback’ (P.61).
To fast-forward (rewind)
To enlarge (playback zoom)
When there is no card inserted, the pictures played back from the built-in memory.
(Clipboard pictures can only be played back in CLIPBOARD mode (P.59).)
Set to
Scroll through pictures
File number
Previous Next
Picture number
Returns to the first picture after the final
picture.
Delete (P.32)
Change information
display (P.33)
Enlarge
View as list (P.61)
Hold down until the desired
picture number is displayed
Turn to
T side
Zoom ratio: 1x/2x/4x/8x/16x
To reduce zoom: Turn lever towards W side
0RYH]RRPSRVLWLRQŸźŻŹ
Enlarging picture will reduce display quality.
Current zoom position (displayed for 1 sec.)
To playback as list (P.61)
To display picture vertically (P.66)
To print
Using own printer:
Ɣ'LUHFWFRQQHFWLRQĺ3Ɣ&RQQHFWLRQYLDFRPSXWHUĺ3
$WSKRWRVKRSVĺ*LYHFDUGWRVKRSDVVLVWDQW

ALL DELETE
MULTI DELETE
SELECT SET CANCEL
MULTI/ALL DELETE
SET
DELETE SINGLE
DELETE THIS PICTURE?
NO
YES
SELECT MULTI/ALL
7
10 11 12
8 9
MULTI DELETE
SELECT
MARK/UNMARK EXIT
DELETE
NO
YES
32 VQT1B83
Basics 6
To delete 1 picture
While picture is
displayed (P.31) Select ‘YES’
Highlight ‘YES’
in orange
To delete multiple (up to 50) or all pictures
Select type of
deletion
Press twice
Skip to step if
selecting ‘ALL DELETE’
Select the pictures to
delete (Repeat)
Picture selected
Select ‘YES’ To cancel
To cancel ‘ALL DELETE’ or ‘ALL
DELETE EXCEPT ’, press
‘MENU/SET’.
Note
Deleted pictures cannot be recovered.
Do not turn off the power during deletion.
Use a sufficiently charged battery or an AC adaptor (DMW-AC5G, optional).
When deleting all pictures from built-in memory, pictures actually deleted differ
according to mode.
PLAYBACK mode : All pictures in built-in memory, except clipboard picture
If ‘FAVORITE’ (P.65) setting is ‘ON’, you can ‘ALL DELETE EXCEPT (FAVORITE)’.
CLIPBOARD mode : All clipboard pictures
Pictures cannot be deleted in the following cases:
ƔProtected pictures (P.69) (Release the protection before deleting)
ƔCard switch is in ‘LOCK’ position.
ƔPictures not of DCF standard (P.90)
May take time depending on number of pictures deleted.
Basics 6
Basics 6Deleting pictures
Set to PLAYBACK mode . Pictures deleted will be from card if card is inserted, or from
built-in memory if not. To delete clipboard pictures, set to CLIPBOARD mode .
Press
7RUHOHDVH3UHVVźDJDLQ
Highlight ‘YES’ in
orange
Press

1/3
10:00 15.MAR.2007
100-0001
1 month 10 days
3RD DAY
1/3
100-0001
100
ISO
AWB
1/30F3.3
10:00 15.MAR.2007
(Example)
OK Dark Bright
3
3
VQT1B83 33
Basics 1
No
display
Histogram During playback zoom (P.31), motion
picture playback (P.62), slideshow (P.64):
Display on/off
During multi playback, calendar playback
(P.61), DUAL DISPLAY (DMC-TZ3 only)
(P.64): Display cannot be changed
Display in PLAYBACK mode
Histogram
Shows brightness of subject as graph,
useful for exposure compensation (P.38),
etc. (Display shown is an estimate.)
Histogram from time of recording
is displayed in orange if different to
histogram in playback, for example when
recording with flash or in dark locations.
Histogram may differ between times of recording and playback, or from histograms
made with image editing software.
Guide lines
Reference for composition (e.g. balance) when recording.
‘GUIDE LINE’ settings (P.20)
Note
Display cannot be changed during menu (P.17) display.
In SIMPLE MODE, display can only be turned on and off.
Histograms cannot be displayed in SIMPLE MODE (P.28), MOTION PICTURE mode
(P.47), or CLIPBOARD mode (P.58).
Basics 1
Applications
(Record) 1Changing recording information
display
LCD monitor
Change between different LCD monitor displays, such as histograms.
Press to change display
Histogram (DMC-TZ3 only)
Guide lines
No display

34 VQT1B83
VQT1B83 35
Applications
(Record) 3Taking pictures with self-timer
Display ‘SELFTIMER’
Select time duration
OFF
10SEC.
2SEC.
10
2
SELFTIMER
SELECT SET
Displayed for approx. 5 sec.
&DQDOVREHVHOHFWHGZLWKŻ
Adjust focus
Press
halfway
Focus will be automatically
adjusted immediately before
recording if shutter button is
pressed fully here.
Take a picture
Press
fully
3
CANCEL
The self-timer indicator will flash, and the
picture will be taken after the selected
duration of time has elapsed.
To cancel while in operation: Press
‘MENU/SET’
This is also effective for correcting jitter when pressing the shutter button, by setting the
self timer to 2 seconds.
Self-timer indicator
MENU/SET
Applications
(Record) 2Making LCD monitor easier to
see
Make it easier to see the LCD monitor when taking pictures from high positions or in
bright outdoor conditions. Display ‘LCD MODE’
Hold down
Select mode
LCD
HIGH ANGLE
OFF
POWER LCD
LCD MODE
SELECT SET
POWER LCD
Makes screen brighter than normal (for
outdoor use).
HIGH ANGLE
Makes screen easier to see when taking
pictures from high positions.
(becomes harder to see from the front)
OFF: Normal
Note
‘HIGH ANGLE’ will be cancelled when power is turned off (including POWER SAVE).
Block out sunlight (with hand, etc) if reflection makes screen difficult to see.
‘HIGH ANGLE’ cannot be used in the following cases.
ƔSIMPLE MODE
ƔPLAYBACK mode
ƔPRINT mode
ƔDuring menu screen display
ƔWhile reviewing pictures
‘POWER LCD’ will be deactivated if no operations are performed for 30 seconds while
recording. (Brightness can be restored by pressing any button)
Brightness/colour of screen in ‘LCD MODE’ has no effect on pictures recorded.
LCD monitor
HIGH ANGLE
Note
This function cannot be used in the ‘UNDERWATER’ scene mode or in MOTION
PICTURE mode .
In some modes, only '2SEC.' or only '10SEC.' may be selected.
SIMPLE MODE: ‘10SEC.’
CLIPBOARD mode, SCENE mode ‘SELF PORTRAIT’: ‘2SEC.’

36 VQT1B83
VQT1B83 37
Available types in each mode (◎: default setting)
SCENE MODE
○−○○○○○◎◎−○−−−○−◎○
○○○○−◎◎○−−−−−◎−−−−
○−○○○○○○○−○−−○○◎○○
−−−−−−−−−−−○○−−−−−
○−○○−−−−−◎−◎○−−−−−
○○○○○○○○○○◎○◎○◎○○◎
Cannot be used with MOTION PICTURE mode and scene modes , , , ,
, , or .
Flash settings may be changed when changing recording mode.
Scene mode flash settings are restored to default when scene mode is changed.
Only or may be selected when using backlight compensation (P.28).
Note
If flash is to be emitted, flash type marks (e.g. ) will turn red when shutter button is
pressed halfway.
No pictures may be taken if these marks (e.g. ) are flashing (flash is charging).
Insufficient flash reach may be due to inadequately set exposure or white balance.
Flash effect may not be fully achieved with high shutter speeds.
Flash charging may take time if battery is low, or if using flash repeatedly.
When using ECONOMY (P.20), LCD monitor is shut off while flash is charging.
Focus range according to ISO sensitivity (‘SENSITIVITY’) (P.51) and zoom
(P.27).
AUTO Max. W:Approx. 0.6-4.2 m Max. T: Approx. 1.0-2.8 m
ISO100 Max. W:Approx. 0.6-1.6 m Max. T: Approx. 1.0-1.1 m
ISO200 Max. W:Approx. 0.6-2.3 m Max. T: Approx. 1.0-1.5 m
ISO400 Max. W:Approx. 0.6-3.3 m Max. T: Approx. 1.0-2.2 m
ISO800 Max. W:Approx. 0.8-4.7 m Max. T: Approx. 1.0-3.1 m
ISO1250 Max. W:Approx. 1.0-4.7 m Max. T: Approx. 1.0-3.1 m
Edges of picture may become slightly dark if using flash at short distances without using
zoom (close to max. W). This may be remedied by using a little zoom.
Maximum ISO sensitivity (‘ISO LIMIT’) (P.51) and focus range when using
Intelligent ISO (P.46).
ISO400 Max. W:Approx. 0.6-3.3 m Max. T: Approx. 1.0-2.2 m
ISO800/ISO1250 Max. W:Approx. 0.6-4.2 m Max. T: Approx. 1.0-2.8 m
Applications
(Record) 4Taking pictures with flash Available types vary depending on the mode in use.
Flash
Do not cover with hand. Do not
look at from close range (few cm).
Do not bring objects close (heat
and light may damage object).
Display ‘FLASH’
Select the desired type
SELECT SET
FORCED FLASH ON
SLOW SYNC./RED-EYE
FORCED OFF
AUTO/RED-EYE
FLASH
AUTO
Displayed for approx. 5 sec.
&DQDOVREHVHOHFWHGZLWKŹ
Types Type, operations Uses
AUTO Normal use
Automatic ON/OFF
AUTO/RED-EYE reduction Taking pictures of subjects in
dark places
Automatic ON/OFF
Reduces red-eye
FORCED FLASH ON
Taking pictures with backlight
or under bright lighting (e.g.
fluorescent)
Always on
FORCED FLASH ON/RED-EYE reduction
(For ‘PARTY’ and ‘CANDLE LIGHT’ scene modes only
(P.42))
Always on
Reduces red-eye
SLOW SYNC./RED-EYE reduction Taking pictures of subjects
against a nightscape (tripod
recommended)
Automatic ON/OFF
Reduces red-eye
Slows shutter speed to take brighter pictures
FORCED OFF Places where flash use is
prohibited
Always off
Two flashes are emitted when using red-eye reduction. Do not move until the second
flash is over. Effects may vary depending on the person.
Shutter speeds are as follows:
, , , : 1/30-1/2000th
, : 1/8 (changed by SLOW SHUTTER setting (P.56)) -1/2000th