Panasonic CF-VDR301U User manual

E
D
F
J
Printed in Japan
HS1206-0
DFQX5627ZA
ENGLISH
OPERATING INSTRUCTIONS
Introduction....................................................5
Handling Precautions....................................6
Using the Drive...............................................8
Using the Software ......................................12
Troubleshooting...........................................21
Specifications...............................................22
DEUTSCH
BEDIENUNGSANLEITUNG
Einführung....................................................23
Vorsichtsmaßnahmen zum Gebrauch .......24
Gebrauch des Laufwerks ............................26
Gebrauch von Software...............................30
Störungsbehebung......................................39
Technische Daten ........................................40
FRANÇAIS
INSTRUCTIONS D’UTILISATION
Introduction..................................................41
Précautions de manipulation......................42
Utilisation du lecteur ...................................44
Utilisation du logiciel...................................48
Dépannage....................................................57
Spécifications...............................................58
日本語
取扱説明書
保証書付き （日本国内向け）
はじめに................................................................
59
安全上のご注意.....................................................
60
使用上のお願い.....................................................
61
ドライブを使う.....................................................
63
ソフトウェアを使う.............................................
67
困ったときの Q&A..............................................
76
仕様........................................................................
77
保証とアフターサービス.....................................
78
・ この取扱説明書をよくお読みのうえ、正し
くお使いください。特に「安全上のご注意」
（60 ページ）は、ご使用前に必ずお読
みいただき、安全にお使いください。お読
みになった後は、保証書と一緒に大切に保
管し、必要なときにお読みください。
・
 保証書は「お買い上げ日・販売店名」などの記
入を確かめ、販売店からお受け取りください。
DVD-ROM & CD-R/RW Drive Pack
DVD-ROM & CD-R/RW ドライブパック
Model No. CF-VDR301U
01CF-VDR301cover.indd101CF-VDR301cover.indd1 2006/12/0515:30:342006/12/0515:30:34

2
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RA-
DIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
12-E-1
WARNUNG!
DIESES PROUKT ERZEUGT LASERSTAHLUNG.
DURCHFÜHRUNG ANDERER VORGÄNGE ALS DER HIER ANGEGEBENEN
KANN ZU GEFÄHRLICHER STRAHLUNG FÜHREN.
REPARATUREN DÜRFEN NUR VON QUALIFIZIERTEM FACHPERSONAL
DURCHGEFÜHRT WERDEN.
12-G-1
AVERTISSEMENT!
CET APPAREIL UTILISE UN LASER.
L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉCUTION DE
PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER
UNE EXPOSITION À DES RADIATIONS DANGEREUSES.
NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOI-MÊME.
CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.
12-F-1
CLASS 1 LASER PRODUCT
LASER KLASSE 1
CF-VDR301.indb1CF-VDR301.indb1 2006/12/019:32:202006/12/019:32:20

3
For U.S.A.
Federal Communications Commission Radio Frequency Interference Statement
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiv-
er is connected.
Consult the Panasonic Service Center or an experienced radio/TV technician for help.
Warning
To assure continued compliance, use only shielded interface cables when connecting to a
computer or peripheral. Also, any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
This device is Class B verified to comply with Part 15 of FCC Rules when used with Pan-
asonic Notebook Computer.
Responsible Party: Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Tel No:1-800-LAPTOP5 (1-800-527-8675)
6-M-1
For Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
7-M-1
CF-VDR301.indb2CF-VDR301.indb2 2006/12/019:32:212006/12/019:32:21

4
Compliance Notice - CE Mark
This equipment is in conformance with the requirements of the European Council Direc-
tive listed below:
73/23/EEC Low Voltage Directive with amendment 93/68/EEC
89/336/EEC EMC Directive with amendments 92/31/EEC and 93/68/EEC
1999/5/EC R&TTE
21-E-1
Übereinstimmungserklärung - CE-Marke
Diese Ausrüstung erfüllt die Anforderungen der unten angegebenen EC-Direktive:
73/23/EEC Niederspannungsdirektive mit Abänderung 93/68/EEC
89/336/EEC EMC-Direktive mit Abänderungen 92/31/EEC und 93/68/EEC
1999/5/EC R&TTE
21-G-1
Avis de comformité - Marque CE
Cet équipement est conforme aux conditions des Directives de la Commission européenne
mentionnées ci-dessous:
73/23/EEC Directive sur la basse tension y compris la modification 93/68/EEC
89/336/EEC Directive CEM y compris les modifications 92/31/EEC et 93/68/EEC
1999/5/EC R&TTE
21-F-1
CF-VDR301.indb3CF-VDR301.indb3 2006/12/019:32:212006/12/019:32:21

5
E
Thank you for purchasing the DVD-ROM & CD-R/RW Drive Pack for the Panasonic
CF-30 notebook computer series*1.
This drive connects to the computer through the multimedia pocket.
Store this manual in a safe place after reading it.
*1For information about the computer(s) for which the DVD-ROM & CD-R/RW Drive Pack can be
used, refer to the catalogs, etc.
Introduction
Microsoft®and Windows®are registered trademarks of Microsoft Corporation in the United States
and/or other countries.
Roxio, the Roxio logo and EASY MEDIA CREATOR are trademarks of Roxio, Inc. which may be
registered in some jurisdictions.
WinDVD™is a trademark of InterVideo, Inc. which may be registered in some jurisdictions.
DVD-ROM & CD-R/RW Drive Pack ....1 Operating Instructions................1
DVD Drive Utility Disc *2.............1
NOTE
The DVD-ROM & CD-R/RW Drive Pack may also be referred to as the drive.
This manual explains the procedure for default settings. The procedure may differ
according to the settings.
: Page in these Operating Instructions or in the Reference Manual.
: Refers to the on-screen manuals.
*2 This contains the programs used to install “EASY MEDIA CREATOR™7 (hereafter, EASY
MEDIA CREATOR)” and “WinDVD™5 (OEM Version) (hereafter, WinDVD).”
CF-VDR301.indb1CF-VDR301.indb1 2006/12/019:32:212006/12/019:32:21

6
E
Handling Precautions
Do not expose the drive to excessive smoke that may leave a residue, e.g., oil smoke, or
tobacco smoke. Doing so can shorten the life of the drive lens.
We recommend cleaning the drive lens with an air puffer used for camera lenses.
(Do not use any spray-type of lens cleaning products.)
When opening/closing the tray
When the computer is on, use the eject button ( page 8) or eject through Windows.
When inserting or removing a disc, be careful not to touch the lens of the drive.
Do not leave the tray open and do not touch the lens.
The lens and disc can become dusty in some conditions. It may cause malfunction in
reading or writing.
Do not apply excessive force to the tray in the open position.
Never insert a foreign object such as a paper clip into the drive.
Doing so may cause malfunction.
Do not place items other than discs on the tray.
Do not access the drive until after the tray is closed and the multimedia pocket device
indicator is off.
While the drive is being accessed
Do not open the tray or move the computer while the drive is being accessed.
Doing so could cause the disc to shift position and this may damage the disc, or cause
the drive to malfunction.
In addition, after running an application involving access to a disc, close the application
before opening the tray or removing the disc.
Drive Handling Care
Do Not Look Into the CD/DVD Drive
Looking directly at the internal laser light source may result in damage to eyesight.
Do Not Use Discs That Are Cracked or Deformed
Because the discs rotate at high speeds, damaged discs may break apart causing injury.
Discs that are not round and discs that have been repaired using adhesives are similarly
dangerous, and so should not be used.
CF-VDR301.indb2CF-VDR301.indb2 2006/12/019:32:222006/12/019:32:22

7
E
Before using a disc, carefully read the operating/handling instructions and package of
the disc.
If the discs are not handled appropriately, they may become dirty or scratched. Further-
more the writing speed may get slower and the data may not be correctly written on or
read from the disc. Other damage may cause a drive failure.
Note the following precautions.
• Do not touch the disc surface (the side with no printing).
• Keep the disc surface clean and free from dirt, dust, fingerprints and scratches.
• Do not write on the surface of the disc with a ballpoint pen or other writing instrument.
• Do not attach stickers to discs.
• Do not drop, bend, or place heavy objects on top of discs.
•
Do not place or store discs in locations exposed to heat, direct sunlight, humidity or dust.
• If a disc is brought from a cold to a warm location, condensation may form on the disc.
For read-only discs, wipe off the condensation using a soft, dry, lint-free cloth before
using the disc. For recordable/rewritable discs, wait until the condensation dries.
•When not using discs, keep them in their protective cases or cartridges.
To clean discs
<For read-only discs>
Wipe discs with a dry, soft cloth from
the center toward the edge.
If discs get very dirty, wipe with a
moist, soft cloth from the center toward the edge, then wipe again with a dry cloth to
take up remaining moisture.
<For recordable/rewritable discs>
Use the Panasonic disc cleaner to clean these discs.
Do not use a cloth, CD cleaners or any other such cleaners under any circumstances.
How to hold a disc
Disc Handling Care
CF-VDR301.indb3CF-VDR301.indb3 2006/12/019:32:222006/12/019:32:22

8
E
Using the Drive
For details on how to insert and remove the drive, refer to “Multimedia Pocket” in the
Reference Manual included with your computer.
Inserting/Removing the Drive
Preparations
Confirm that [Transfer Mode] is set to [DMA if available] in [start] - [Control Panel] -
[Performance and Maintenance] - [System] - [Hardware] - [Device Manager] - [IDE ATA/
ATAPI controllers] - [Primary IDE Channel] - [Advanced Settings] - [Device 0]. Perform
this setting if it has not yet been made.
1 Turn on the computer.
2 Slide the latch (A) and open the cov-
er.
3 Press the eject button (B) and slowly
pull out the tray.
4 Insert/Remove the disc.
To insert
Set the disc with the label side up and press the
center of the disc until it clicks in place.
To remove
Press on the center spindle (C) and carefully lift up
the edge of the disc.
5 Close the tray.
Do not press the eject button.
Setting a Disc
CF-VDR301.indb4CF-VDR301.indb4 2006/12/019:32:222006/12/019:32:22

9
E
NOTE
To remove a disc when the computer is powered off, insert a pointed object (e.g.,
the bent-out tip of a paper clip) into the emergency hole (D). Pushing it to the end
allows the tray to come out.
If the vibration of the drive is excessive, check the disc. If the disc is normal and
is inserted correctly, set [DVD Drive Speed] to [Low] in the [Main] menu of the
Setup Utility ( Reference Manual “Setup Utility”).
For AutoPlay CD:
• If an AutoPlay CD does not start after the computer resumes from standby or hiber-
nation, remove the disc from the drive and then reinsert it after waiting 15 seconds.
• An AutoPlay CD may start during file access depending on the status of the disc.
When playing back video from a disc, playback may not be smooth in some conditions.
If the drive is not accessed for 30 seconds, the drive motor will automatically be shut
down to reduce the power consumption. When the drive is accessed again, the drive motor
is turned on. In this case, reading of the disc data will take approximately 30 seconds.
Power-saving Mode
CF-VDR301.indb5CF-VDR301.indb5 2006/12/019:32:222006/12/019:32:22

10
E
Information
NOTE
[Confirm Region] appears when the DVD-Video has only one region code and the
drive is set for another region code.
([Confirm Region] may not appear with some DVD-Video discs. To check the cur-
rent region code and the number of remaining times of changing the code, right-
click on the [WinDVD] screen and click [Setup] - [Region].)
You can change the region code setting up to five times including the initial setting.
Be extremely careful because you cannot change the region code anymore after the
fifth change, even if you reinstalled the operating system.
Any problem resulting from illegal changing or altering of the region code is the
user’s responsibility.
CAUTION
To play DVD-Video or MPEG2 files, install the DVD playback software using “DVD
Drive Utility Disc” (included).
For information on how to install the software, refer to page 18.
Region Code Setting
DVD-Video are allocated to region codes according to where they are sold. To play a
DVD-Video, the player’s software and the drive must have the corresponding region code.
e.g.,
For U.S.A. and Canada: “1”
For Europe: “2”
The region code of the drive is not set at purchase. The operation depends on the DVD-
Video that is first played.
• DVD-Video with a specific region code:
The drive will automatically be set at the same region code as the DVD-Video.
•DVD-Video with multiple region codes:
[Confirm Region] appears. Select the region code and click [OK]. Play now begins.
Using the Drive
CF-VDR301.indb6CF-VDR301.indb6 2006/12/019:32:222006/12/019:32:22

11
E
Writing to Discs
Writing software is required to write data to a disc.
Install “EASY MEDIA CREATOR” using “DVD Drive Utility Disc” (included).
( page 14)
Be sure to use discs conforming to the proper write speeds. ( page 22)
If the write operation is to involve a long period of time, be sure to connect the AC
adaptor of the computer. If the battery power runs low and the power of the computer is
cut, the write operation may end in failure.
You can read from/write to the following discs.
You can read from the following discs.
*1 DVD-RAM: Only non-cartridge type or removable cartridge type can be used.
*2 Does not support DVD-RW Ver.1.0.
<CD-R>
HITACHI MAXELL, Ltd.
MITSUBISHI KAGAKU MEDIA CO., Ltd.
RICOH Co., Ltd.
TAIYO YUDEN Co., Ltd.
<CD-RW/High-Speed CD-RW>
MITSUBISHI KAGAKU MEDIA CO., Ltd.
RICOH Co., Ltd.
<Ultra-Speed CD-RW>
MITSUBISHI KAGAKU MEDIA CO., Ltd.
Recommended discs for writing
• The quality of written data depends on the disc.
CF-VDR301.indb7CF-VDR301.indb7 2006/12/019:32:222006/12/019:32:22

12
E
Using the Software
Do not install the software using a drive other than this drive. Be sure to insert this
drive into your computer, and then insert the disc for installation.
Close all other software application before running the Setup program for the soft-
ware applications.
Log on to Windows as an administrator.
CAUTION
NOTE
To play a DVD-Video, use “WinDVD”. ( page 18)
Install the software application contained in the “DVD Drive Utility Disc” (supplied):
“EASY MEDIA CREATOR” and “WinDVD”
Insert the drive into the multimedia pocket. ( Reference Manual “Multimedia
Pocket”)
Before Installing the Software
CF-VDR301.indb8CF-VDR301.indb8 2006/12/019:32:232006/12/019:32:23

13
E
EASY MEDIA CREATOR
“EASY MEDIA CRAETOR” is CD writing software application developed by Roxio, Inc.
Here, explanations are given on general information about “EASY MEDIA CRAETOR,”
the installation procedure, and how to access the online manual. For further information,
refer to the online manual of “EASY MEDIA CREATOR” ( page 16).
General Information
What you can do with this software application
• Creation of music CDs and data CD: Use Creator Classic utility.
• Creation of back-up CD: Use Disc Copier utility.
• Creation of CD labels, etc.: Use Label Creator utility.
• Writing files to CD discs like writing to floppy disks, etc.: Use Drag-to-Disc Utility.
• Restoring the backup data divided into the multiple discs*1: Use Creator Classic Util-
ity.
• Restoring the data from the encrypted discs*1: Use Creator Classic Utility.
*1The Roxio Retrieve utility automatically starts up from these discs.
NOTE
For details on the functions of the software application and media, refer to the on-
line manual of the application as well.
About Copies
When writing to discs, make sure that you are not infringing any copyrights.
It is illegal to copy audio CDs for non-personal use.
When backing up software, make sure that you are not infringing any software copy-
rights for that product.
CF-VDR301.indb9CF-VDR301.indb9 2006/12/019:32:232006/12/019:32:23

14
E
Using the Software
1 GB of free space on the hard disk is needed to install all the components of “EASY
MEDIA CREATOR.”
Close all other software application before running the Setup program for “EASY
MEDIA CRAETOR.”
Log on to Windows as an administrator.
CAUTION
NOTE
Depending on the computer, preparatory steps may be necessary before installa-
tion. Before installing the application, be sure to read the Operating Instructions or
Reference Manual of the computer.
1Log on to Windows as an administrator.
2Set “DVD Drive Utility Disc” in the drive.
3At the confirmation message, click [OK].
[Utility Setup tool] screen will appear (allow some time for disc recognition).
When the setup program will not run automatically, input [x:\setuputil.exe]*1in [start]
- [Run] and click [OK].
*1 “x” is the drive letter. You can change the letter to suit your preference.
4Click [Easy Media Creator Setup].
5
Select your language at [Choose Setup Language], then click [OK].
Follow the on-screen instructions.
During the installation, you will be required to agree the License Agreement. After
reading the agreement, click [I accept the terms in the license agreement], then click
[Next].
6Click [Finish].
7A message appears advising that the computer must be restarted. Click [Yes].
The following settings are required to use discs containing data written using Drag-
to-Disc with Roxio’s DirectCD5 which has been installed on another computer.
ASelect on the [Drag-to-Disc] screen, and click [Settings].
BClick [Advanced Eject Settings], and click [UDF version on current disc] in
[Nonrewritable Media] and [Rewritable Media].
CClick [OK].
DClick [OK].
To install the software application, follow the procedure below.
Installing EASY MEDIA CREATOR
CF-VDR301.indb10CF-VDR301.indb10 2006/12/019:32:232006/12/019:32:23

15
E
Click [start] - [All Programs] - [Roxio Easy Media Creator 7 Basic Edition].
You can run each utility from the [Roxio Easy Media Creator 7 Basic Edition] screen. You
can also run each utility by following the procedure below.
Creator Classic
Click [start] - [All Programs] - [Roxio] - [Creator Classic].
Disc Copier
Click [start] - [All Programs] - [Roxio] - [Disc Copier].
Label Creator
Click [start] - [All Programs] - [Roxio] - [Label Creator].
Drag-to-Disc
Drag-to-Disc will automatically start up after “EASY MEDIA CREATOR” has been
installed or when Windows starts up.
To restart Drag-to-Disc after exiting:
Click [start] - [All Programs] - [Roxio] - [Drag-to-Disc].
Roxio Retrieve
Click [start] - [All Programs] - [Roxio] - [Roxio Retrieve].
Running EASY MEDIA CREATOR
CF-VDR301.indb11CF-VDR301.indb11 2006/12/019:32:232006/12/019:32:23

16
E
Using the Software
After running each utility, you can access the online manual.
Creator Classic
Click [Help] from the menu, and them click [Creator Classic Help Center].
Disc Copier
Click [Help] from the menu, and them click [Disc Copier Help Center].
Label Creator
Click [Help] from the menu, and them click [Label Creator Help Center].
Drag-to-Disc
Click on [Drag-to-Disc] screen.
Roxio Retrieve
Click on the top left of the corner, and then click [Roxio Retrieve Help Center].
How to access the Online Manual
After erasing the data in the disc following the order of [Disc and Device Utility] - [Erase/
Format...] - [Quick Erase/Format] - [Start], remove the disc once before reuse.
<When using Drag-to-Disc>
In the following cases, first log off and then log back on.
• When [Drag-to-Disc drive] does not appear on the menu even after right-clicking the
file and clicking [Send to].
• When an error message is displayed after right-clicking the file and clicking [Send to] -
[Drag-to-Disc drive]
Do not use Drag-to-Disc to write data on a disc which was formatted using software
other than Drag-to-Disc. You may not be able to write data on the disc using any other
software.
When a CD cannot be formatted with Drag-to-Disc, try formatting it with the adminis-
trator authority.
When using “EASY MEDIA CREATOR,” set the display resolution to 1024 × 768 or
more.
Cautions on Use
CF-VDR301.indb12CF-VDR301.indb12 2006/12/019:32:232006/12/019:32:23

17
E
If “EASY MEDIA CREATOR” does not operate properly, we recommend carefully
reading the online help file first for problems with the operating environment or opera-
tions.
Then install the latest Windows Service Pack.
If you still cannot troubleshoot the problem, contact Panasonic Technical Support.
For further information, refer to the following URL.
http://www.roxio.com/
Information
CF-VDR301.indb13CF-VDR301.indb13 2006/12/019:32:232006/12/019:32:23

18
E
Using the Software
You can run “WinDVD” using either of the following procedures.
Double-click on the desktop.
Click [start] - [All Programs] - [InterVideo WinDVD] - [InterVideo WinDVD].
Running WinDVD
WinDVD
Installing WinDVD
WinDVD is a software application for DVD playback.
Install “WinDVD” using “DVD Drive Utility Disc” ( below).
1Log on to Windows as an administrator.
2Set “DVD Drive Utility Disc” in the drive.
3At the confirmation message, click [OK].
[Utility Setup tool] screen will appear (allow some time for disc recognition).
When the setup program will not run automatically, input [x:\setuputil.exe]*1in [start]
- [Run] and click [OK].
*1 “x” is the drive letter. You can change the letter to suit your preference.
4Click [WinDVD Setup].
5Click [Next] at the Welcome Message.
6After reading the “License Agreement”*2, click [Yes] if you agree to the terms.
*2Refer to the “LIMITED USE LICENSE AGREEMENT” on the Operating Instruc-
tions of the computer.
7Follow the on-screen instructions and install “WinDVD”.
To access the Online Manual
Click “?” of the WinDVD control panel.
Right-click on the [WinDVD] screen and click [Help].
CF-VDR301.indb14CF-VDR301.indb14 2006/12/019:32:242006/12/019:32:24

19
E
NOTE
DVD-Audio cannot be played back using “WinDVD”.
Do not start “WinDVD” while the hard disk drive indicator is blinking immedi-
ately after the computer is turned on.
While “WinDVD” is running, do not:
• Enter standby or hibernation.
• Switch the display by pressing Fn + F3 .
During video playback, do not:
• Eject the disc.
• Use other applications or the Command Prompt.
• Change the settings of the screen properties.
If you maximize the video display window, you can return to the original window
size by double-clicking over the images.
When the number of display colors is increased, a message appears and the DVD
cannot be played:
• Reduce the number of display colors.
• Right-click on the desktop, click [Properties] - [Settings] - [Advanced Settings] -
[Troubleshoot] and maximize the value of [Hardware acceleration].
Immediately after resuming from a pause, frame dropping may occur depending
on the operating environment or DVD-Video (images or sounds are disrupted).
In the Extended Desktop or simultaneous (internal/external) display mode, there
are times when images or video are not displayed correctly.
During a prolonged period of rapid advance, the pause mode may be established at
some point. If this happens, exit “WinDVD”, and restart.
Do not install another player software together with “WinDVD”.
Doing so may interfere with smooth playback. Some DVD-Video discs contain the
player software and start installing. In this case, cancel the installation as soon as
possible. If you accidentally installed another player software and find a problem
in playback, try either of the following procedures.
• Uninstall the player software by clicking [start] - [Control Panel] -
[Add or Remove Programs].
• Set “WinDVD” as the playback software if you can select the option in the
player software settings.
CF-VDR301.indb15CF-VDR301.indb15 2006/12/019:32:242006/12/019:32:24

20
E
Using the Software
The following restrictions apply:
Depending on the condition (record quality, cracks, dirt, modification, copy protection,
type of drive/disc maker used when creating the disc, etc.) of a disc, it may not be pos-
sible to be read or play it correctly.
In order to play discs other than DVD-RAM, they must be finalized (a process that en-
ables it to play on other DVD players, etc.). For information on the finalizing method
used by your DVD recorder, refer to its operating instructions.
Media in which digital broadcasts have been recorded using copyright management
technologies such as CPRM (Content Protection for Recordable Media) cannot be
played back.
DVD Discs Created Using a DVD Recorder
SUPPORT INFORMATION
If “WinDVD” does not operate properly, we recommend carefully reading the online
help file first for problems with the operating environment or operations.
If you still cannot troubleshoot the problem, enter the required information in the in-
quiry form on the InterVideo, Inc. homepage (http://www.intervideo.com/), and sub-
mit the form.
CF-VDR301.indb16CF-VDR301.indb16 2006/12/019:32:242006/12/019:32:24