Panasonic ER-GB37 User manual

© Panasonic Corporation 2014 Unauthorized copy-
ing and distribution is a violation of law.
ORDER NO. SD1408A54CE
Rechargeable Beard Trimmer
Model No. ER-GB37
Asia
Middle East
TABLE OF CONTENTS
PAGE
1 Warning -------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide ----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------- 6
6 Schematic Diagram ---------------------------------------------- 6
7 Exploded View and Replacement Parts List ------------ 7

ER-GB37
2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70F (30 - 40) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20F (400 ± 10). In case of using high temperature soldering
iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100F / 600C).
2 Specifications
Power source Asia AC 220-240V, 50Hz
India AC 230V, 50Hz
Middle East AC 220-240V, 50-60Hz
Motor voltage 1.2V
Charging time Approx. 8-10 hours
Weight 150g (excluding comb attachment)
Supplied accessories Comb attachment
Cleaning brush
Oil

ER-GB37
3
3 Troubleshooting Guide
(Refer to WIRING CONNECTION DIAGRAM)

ER-GB37
4
4 Disassembly and Assembly Instructions
4.1. Disassembly Instuctions
Follow the procedure below to disassemble the main unit.
1. Remove the comb attachment and the blade.
2. Loosen two screws and remove the blade holder.
3. Loosen a screw from bottom cover.
4. Take out the front panel from the housing.
5. Take out the dial from the unit.
6. Loosen 8 screws.

ER-GB37
5
7. Separate the housing B from the housing A.
8. Loosen 2 screws.
9. Remove the battery from the chassis.
10. Remove the motor.
4.2. Cautions in Assembly
NOTE:
When reassembling, replace the new waterproof rubber.
Make sure whether there is NO foreign substance sticking
around a part covered with water seal.
NOTE:
Make sure to assemble the battery last in order to avoid
short-circuit.
4.2.1. Motor
Place the red mark on upper side. Fit the shape of motor bal-
ancer and the hole of housing A and insert into housing A.
4.2.2. Battery case
Align the projection of switch select button on housing A with
the groove of switch plate on battery case.
NOTE:
Make sure to assemble the washer and O-ring into the bat-
tery and lever.

ER-GB37
6
5 Wiring Connection Diagram
6 Schematic Diagram

ER-GB37
7
7 Exploded View and Replacement Parts List
7.1. Exploded View

ER-GB37
8
7.2. Replacement Parts List
Safety Ref.
No.
Part No. Part Name & Description Quan-
tity
Remarks
1 WER9605E BLADE BLOCK 1
2 WES7025L9707 SCREW 2
3 WER217L0967 O-RING B 2 (6PCS/PK)
4 WER504L0166 SPRING FOR CUTTER 2 (2PCS/PK)
5 WERGB37K1588 BLADE HOLDER 1
6 WERGB37K3288 ADJUSTING DIAL 1
7 WERGB37K3968 FRONT PANEL 1
8 WERGB37K3058 HOUSING A 1
9 WERGB37K3068 HOUSING B 1
9 WERGB37K3069 HOUSING B 1 only for India
10 WERGB37L0588 HOUSING O-RING 1
11 WERGB40L0458 CLICK BUTTON 1
12 WERGB40L0178 SPRING A 1
13 WERGB37L1008 MOTOR ASSEMBLY 1
14 WESRW35L2508 RECHARGEABLE BATTERY 1 Ni-MH Type, (2PCS/PK)
15 WESRW30L0977 WASHER & O-RING SET 1
16 WESRW30L0237 BATTERY HOLDER 1
17 WES8176L6056 TAPPING SCREW 11 K2-8
18 WERGB37K3038 BODY BLOCK 1
18 WERGB37K3031 BODY BLOCK 1 only for India
19 WERGB37K7398 COMB ATTACHMENT 1
20 WERGB37K7676 AC ADAPTOR 1 C-2 PLUG
20 WERGB37K7675 AC ADAPTOR 1 BF3 PLUG
20 WERGB37K7655 AC ADAPTOR 1 C-2 PLUG, only for India
21 WERGB30H7048 CLEANING BRUSH 1
22 WERGC20X7918 OIL 1
- WERGB37K8008 INDIVIDUAL BOX 1 only for BF3 Plug model
- WERGB37K8009 INDIVIDUAL BOX 1
- WERGB37K8000 INDIVIDUAL BOX 1 only for India
- WERGB37K8108 OPERATING INSTRUCTIONS 1
- WERGB37K8109 OPERATING INSTRUCTIONS 1 only for India