10
RQTX1328
Getting StartedPlaying DiscsOther OperationsReference
Up to 30 stations can be set.
≥“SET OK” is displayed when the stations are set, and the radio tunes to
the last preset station.
≥“ERROR” is displayed when auto presetting is unsuccessful. Preset the
stations manually (Bbelow).
≥The FM setting is also shown on the TV display.
To cancel the mode, press and hold the button again until “AUTO ST” is
displayed.
≥The mode is also cancelled when you change the frequency.
Up to 30 stations can be set.
A station previously stored is overwritten when another station is stored in
the same channel preset.
You can select desired source, change the settings, access playback/
menus, etc., by using the START menu.
When “Input Selection” is selected
You can select a desired source from the menu.
≥DVD/CD (B12), FM RADIO (Bleft), AUX§(Bbelow), ARC§
(Bbelow),
USB
(B16)
§“(TV)” will appear beside “AUX” or “ARC”, indicating the TV audio
setting for VIERA Link “HDAVI Control” (B15).
When “Setup” is selected
You can change the settings for this unit. (B16)
Other selectable items
The items that are displayed will vary depending on the media and
source.
When a disc is loaded or an USB device is connected, you can also
access playback or menus from the START menu.
e.g. [DVD-V]
When the on-screen control panel appears
e.g. [DVD-V] (when “Playback Disc” is selected from the START menu)
You can operate the playback with the indicated controls.
Confirm the audio connection to the AUX or HDMI AV OUT terminal on the
main unit when you select the corresponding sources (B8). Reduce the
volume on the TV to its minimum, and then adjust the volume of the main unit.
Listening to the radio
Presetting stations automatically
1Press [RADIO]4to select “FM”.
2Press [MENU]C.
Each time you press the button:
LOWEST (factory preset):
To begin auto preset with the lowest frequency.
CURRENT:
To begin auto preset with the current frequency.§
§ To change the frequency, refer to “Manual tuning” (Bbelow).
3Press and hold [OK]8.
Release the button when “FM AUTO” is displayed.
The tuner starts to preset all the stations it can receive into the
channels in ascending order.
Listening/confirming the preset channels
1Press [RADIO]4to select “FM”.
2Press the numbered buttons to select a channel.
≥To select a 2-digit number
e.g. 12: [S10]2B[1] B[2]
Alternatively, press [X,W]@.
If noise is excessive
Press and hold [PLAY MODE]9to display “MONO”.
Manual tuning
1Press [RADIO]4to select “FM”.
2Press [SEARCH6, SEARCH5]?to select the
frequency.
≥To start auto tuning, press and hold [SEARCH6,
SEARCH5]?until the frequency starts scrolling. Tuning stops
when a station is found.
Presetting stations manually
1 While listening to the radio broadcast
Press [OK]8.
2 While the frequency is flashing on the display
Press the numbered buttons to select a channel.
≥To select a 2-digit number
e.g. 12: [S10]2B[1] B[2]
Alternatively, press [X,W]@, and then press [OK]8.
Using the START menu
1Press [START]Bto show the START menu.
≥When using VIERA Link “HDAVI Control”, the TV also turns on
when the START menu is displayed.
2Press [3,4]8to select an item and press [OK]8.
≥To exit, press [START]B.
3Press [3,4,2,1]8to make the setting and press
[OK]8.
Selecting the source using the remote control
Press To select
[DVD]4DVD/CD
[RADIO]4FM (Bleft)
[EXT-IN]4Each time you press the button:
AUX:
ARC:
USB:
For audio input through the AUX terminal.
For audio input through the HDMI AV OUT terminal.
(B16)
Input Selection
Setup
DVD/CD Home Cinema
DVD/CD Home Cinema
Input Selection
Setup
Playback Disc
TOP MENU(DVD)
MENU(DVD)
SC-XH55-50 GSGAGWGN_RQTX1328-1B_eng.book Page 10 Wednesday, March 2, 2011 5:33 PM
