Panasonic CF-Y5LWVYZ1 TOUGHBOOK User manual

Order No. CPD0611208C1
Notebook Computer
CF-Y5
©2006 Matsushita Electric Industrial Co., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation of law.
This is the Service Manual for
the following areas.
M …for U.S.A. and Canada
Model No. CF-Y5LWVYZ 12
1: Operation System
B: Microsoft® Windows® XP Professional
2: Area
M: Refer to above area table

2
This apparatus must be earthed for your safety.
To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point
which is effectively earthed through the normal household wiring.
Extension cords used with the equipment must be three-core and be correctly wired to provide connec-
tion to earth. Wrongly wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply that the power point is earthed and
that the installation is completely safe.
For your safety if you have any doubt about the effective earthing of the power point consult a quali-
fied electrician.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 3 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 3 amps and
that it is approved by ASTA or BSI to BS 1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR
HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED
OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
Warning: THIS APPLIANCE MUST BE EARTHED.
Important
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug
which is marked by the letter E or by the safety earth symbol coloured GREEN or GREEN-and-
YELLOW.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or
coloured BLACK.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L
or coloured RED.
The mains plug on this equipment must be used to disconnect the mains power.
Please ensure that a socket outlet is available near the equipment and shall be easily accessible.
How to replace the fuse
Open the fuse compartment with a screw-
driver and replace the fuse.
Warnings
This equipment is not designed for connection to an IT power system.
(An IT system is a system having no direct connections between live parts and Earth; the exposed-conducive-
parts of the electrical installation are earthed.
An IT system is not permitted where the computer is directly connected to public supply systems in the U.K.)
Disconnect the mains plug from the supply socket when the computer is not in use.
This equipment is produced to BS800/1983.
For U.K.
WARNING

3
LASER SAFETY INFORMATION
For U.S.A.
Class 1 LASER-Product
This product is c rtifi d to comply with DHHS Rul s 21 CFR Subchapt r J.
This product compli s with Europ an Standard EN60825 (or IEC Publication 825)
For all ar as
This quipm nt is classifi d as a class 1 l v l LASER product and th r is no hazardous LASER radiation.
Caution:
(1) Us of controls or adjustm nts or p rformanc of proc dur s oth r than thos sp cifi d h r in may r sult in
hazardous radiation xposur .
(2) Th driv is d sign d to b incorporat d into a comput r-bas d syst m or unit which has an nclosing cov r.
It should n v r b us d as a stand alon driv .
Dang r:
Th s rvic man should not r mov th cov r of driv unit and should not s rvic b caus th driv unit is a non-
s rvic abl part.
Pl as ch ck DANGER lab l on PD-driv unit.
Unplug th AC pow r cord to th quipm nt b for op ning th top cov r of th driv .
Wh n th pow r switch it on, do not plac your y s clos to th front pan l door to look into th int rior of th unit.
LASER Sp cification
Class 1 l v l LASER Product
Wav L ngth: DVD 658–8 nm
CD 775~815 nm
Las r saf ty information is appropriat only wh n driv with las r is install d.

4

5

CONTENTS
1. Sp cifications 7
2. Nam s and Functions of Parts 10
3. Block Diagram 12
4. Diagnosis Proc dur 13
5. Pow r-On S lf T st (Boot Ch ck) 15
6. List of Error Cod s <Only wh n th port r plicator is conn ct d> 16
7. S lf Diagnosis T st 18
8. Wiring Conn ction Diagram 23
9. Disass mbly/R ass mbly 24
10. Explod d Vi w 80
11. R plac m nt Parts List 83

7
1 Specifications
Getting StartedUseful InformationTroubleshootingAppendix
Main Specifications
Model No. CF-Y5LWVYZBM
CPU/
Secondary cache memory Intel®Core™ Duo Processor Low Voltage L 2400 (1.66 GHz, 2 MB*1 L2 cache, 667
MHz FSB)
Chip Set Mobile Intel®945 GMS Express chip set
Main Memory 512 MB*1, DDR2 SDRAM (1536 MB*1 Max.)
Video Memory UMA (128 MB*1 Max.)*2
Hard Disk Drive 60 GB*3
CD/DVD Drive USB 2.0 connection interface
DVD MULTI Drive built-in, Buffer underrun error prevention function: Supported
Continuous Data Trans-
fer Speed*4*5 Reading*6 zDVD-RAM*7: 2X (4.7 GB*3)/1X (2.6 GB*3) zDVD-R*8: 4X (Max.) zDVD-RW: 4X
(Max.) zDVD-ROM: 8X (Max.) zCD-ROM: 24X (Max.) zCD-R: 24X (Max.) zCD-RW:
20X (Max.) z+R: 4X (Max.) z+R DL: 4X (Max.) z+RW: 4X (Max.)
Writing*9 zDVD-RAM*7: 2X (4.7GB*3) zDVD-R: 1X/2X/4X zDVD-RW: 1X/2X z+R: 2.4X/4X
z+RW: 2.4X zCD-R: 4X/8X/8-16X/8-24X zCD-RW: 4X zHigh-Speed CD-RW: 4X/8X/
10X zUltra-Speed CD-RW: 8X/10X
Supported Disks/For-
mat*5 Reading zDVD-ROM (Single Layer, Dual Layer) zDVD-Video zDVD-R*8(1.4 GB, 3.95 GB, 4.7
GB)*3 zDVD-RW (Ver.1.1/1.2 1.4 GB, 4.7 GB, 9.4 GB)*3 zDVD-RAM*7 (1.4 GB, 2.8 GB,
2.6 GB, 5.2 GB, 4.7 GB, 9.4 GB)*3 z+R (4.7 GB)*3 z+R DL (8.5 GB)*3 z+RW (4.7 GB)*3
zCD-Audio zCD-ROM (XA compatible) zCD-R zPhoto CD (multiple session compati-
ble) zVideo CD zCD-EXTRA zCD-RW zCD-TEXT
Writing zDVD-RAM*7 (1.4GB, 2.8GB, 4.7GB, 9.4GB)*3zDVD-R (1.4GB, 4.7GB for General)*3
z
DVD-RW (Ver.1.1/1.2 4.7 GB , 9.4 GB )
*3
z +R (4.7 GB
*3
) z +RW (4.7 GB
*3
) z CD-R z CD-RW
Display Method 14.1 SXGA+ type (TFT) (1400 × 1050 dots)
Internal LCD 65,536/16,777,216 colors (1400 × 1050 dots)*10
External Display*11 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 ×
1024 dots/1400 × 1050 dots/1600 × 1200 dots/2048 × 1536 dots (60 Hz)*12)
Simultaneous Display on LCD + Exter-
nal Display*11 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 ×
1024 dots/1400 × 1050 dots)*10
Wireless LAN Intel®PRO/Wireless 3945 ABG Network Connection(next page)
Bluetooth™ (next page)
LAN*13 IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX
Modem Data: 56 kbps (V.92) FAX: 14.4 kbps
Sound WAVE and MIDI playback, Intel®High Definition Audio subsystem support, Stereo
Speakers (built in)
Security Chip TPM (TCG V1.2 compliant)*14
Card Slots PC Card Slot × 1, Type I or Type II, Allowable current 3.3 V: 400 mA, 5 V: 400 mA
SD Memory Card Slot*15 × 1, Data transfer rate = 8 MB per second
RAM Module Slot × 1, DDR2 SDRAM, 172-pin, 1.8 V, Micro DIMM, PC2-4200 Compliant*16
Interface USB Ports × 2 (USB2.0 × 2)*17 / Modem Port (RJ-11) / LAN Port (RJ-45) *13 /
External Display Port: Mini Dsub 15-pin female / Microphone Jack: Miniature jack, 3.5
DIA / Headphone Jack: Miniature jack, 3.5 DIA / Mini Port Replicator connector: Dedi-
cated 50-pin male
Keyboard/Pointing Device 87 keys/Touch Pad
Power Supply AC adaptor or Battery pack
AC Adaptor*18 Input: 100 V - 240 V AC, 50 Hz/60 Hz
Output: 16 VDC, 3.75 A
Battery Pack Li-ion 10.65 V, 5.7 Ah
Operating Time*19 Approx. 5 hours - 8 hours*20 (Approx. 6 hours*21) (Disable Economy Mode (ECO))
Charging Time*22 Approx. 5 hours (Power off)/Approx. 6.5 hours (Power on)

8
Getting StartedUseful InformationTroubleshootingAppendix
*1 1 MB = 1,048,576 bytes
*2 A segment of the main memory is allotted automatically
depending on the computer’s operating status. The size of
the Video Memory cannot be set by the user.
*3 1 GB = 1,000,000,000 bytes. Your operating system or some
application software will report as fewer GB.
*4 Data transfer speeds indicate values measured by
Matsushita Electric Industrial Co., Ltd. The data transfer rate
of DVD per 1X speed is 1,350 KB/s. The data transfer rate of
CD per 1X speed is 150 KB/s.
*5 Performance of CD-R, CD-RW, DVD-RAM, DVD-R, DVD-
RW, +R, +R DL, and +RW cannot be guaranteed depending
on writing status and recording format. Also, some data can-
not be played back depending on the disk, settings, and
environment being used.
Does not support writing to DVD-R DL/+R DL (dual layer
disks) or reading from DVD-R DL.
*6 If an unbalanced disk (e.g., a disk with which the balance
has been displaced from the center) is inserted, the speed
may become slower if there are large vibrations while the
disk is rotating.
*7 Only non-cartridge type or removable cartridge type can be
used.
When writing to DVD-RAM, use only disks up to 3x. This
application cannot be used with 5x DVD-RAM media (2-5x
disks, etc.).
*8 DVD-R is compatible with 4.7 GB (for General) playback.
DVD-R (for Authoring) playback is compatible with disks
recorded using Disk-at-Once recording.
*9 Depending on the disk, the writing speed may become
slower.
*10 A 16,777,216 color display is achieved by using the dithering
function.
*11 Display may be impossible using some connected external
displays.
Power Consumption*23 Approx. 35 W*24 / Approx. 60 W(maximum when recharging in the ON state)
Physical Dimensions (W ×H×D) 309.6 mm ×28 mm (at the front)/44.5 mm (at the rear) ×245.5 mm (excluding protru-
sion) {12.2 " ×1.1 " / 1.8 " ×10.0 "}
Weight*25 Approx. 1530 g{3.4 lb.}
Environment Operation Temperature 5°Cto 35°C{41°Fto 95°F}
Humidity 30%to 80%RH (No condensation)
Storage Temperature -20°Cto 60°C{-4°Fto 140°F}
Humidity 30%to 90%RH (No condensation)
OS*26 Microsoft®Windows®XP Professional Service Pack 2 with Advanced Security Technol-
ogies (NTFS File system)
Pre-installed Software*26 Microsoft®Internet Explorer 6 Service Pack 2 / DirectX 9.0c /Microsoft®Windows®
Media Player 10 / Microsoft®Windows®Movie Maker 2.1 / Microsoft®.NET Framework
1.1 SP1/2.0 / Adobe Reader / Intel®PROSet/Wireless Software <Only for model with
wireless LAN> / SD Utility / Icon Enlarger / Loupe Utility / Touch Pad Utility / DMI Viewer
/ PC Information Viewer / WinDVD 5 (OEM Version) / B’s Recorder GOLD8 BASIC / B’s
CLiP 6*27 / Hotkey Settings / Optical Disc Drive Letter-Setting Utility / Optical Disc Drive
Power-Saving Utility / Wireless Switch Utility <Only for model with wireless LAN/Blue-
tooth> / Economy Mode (ECO) Setting Utility / Battery Recalibration Utility / Infineon
TPM Professional Package V2.5*28 / Recover Pro 6*28
Setup Utility / Hard Disk Data Erase Utility*29 / PC-Diagnostic Utility*30
Model No. CF-Y5LWVYZBM
Wireless LAN
Data Transfer Rates IEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched)*31
IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched)*31
IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched)*31
Standard Supported IEEE802.11a/IEEE802.11b/IEEE802.11g
Transmission Method OFDM system, DS-SS system
Wireless Channels Used IEEE802.11a: Channels 36/40/44/48/52/56/60/64/149/153/157/161/165
IEEE802.11b/ IEEE802.11g: Channels 1 to 11
RF Frequency Band IEEE802.11a: 5.18 - 5.32 GHz, 5.745 - 5.825 GHz
IEEE802.11b/ IEEE802.11g: 2412 - 2462 MHz
Bluetooth™
Bluetooth Version 2.0 + EDR
Transmission Method FHSS system
Wireless Channels Used Channels 1 to 79
RF Frequency Band 2.402-2.48 GHz
Power Class Class 1

9
Getting StartedUseful InformationTroubleshootingAppendix
*12 When using an external display with a resolution of 2048 x
1536 dots, use a display that supports a 60Hz refresh rate. If
an external display that does not support a 60Hz refresh rate
is used, images may not be displayed properly.
*13 Some devices cannot be used depending on the port type.
*14 For information on TPM, click [start] - [Run] and input
“c:\util\drivers\tpm\README.pdf”, and refer to the Installation
Manual of “Trusted Platform Module (TPM)”.
*15 Operation has been tested and confirmed using Panasonic
SD Memory Cards with a capacity of up to 2 GB.
The transfer rate using the SD Memory Card slot on this
computer is 8 MB per second. (This is a theoretical value,
and differs from actual speeds.)
The transfer rate is 8 MB per second even if you use an SD
Memory Card that supports high-speed transfer rates.
Operation on other SD equipment is not guaranteed.
This computer is not compatible with MultiMediaCards or
SDHC Memory Cards.
Do not insert these kinds of cards.
*16 Only a RAM module designed for DDR2 (PC2-4200) can be
added (Panasonic : CF-BAW0512U, CF-BAW1024U).
JEDEC standard 214 pin Micro DIMM cannot be used.
PC2100 / PC2700 172 pin Micro DIMM cannot be used.
If a PC2-3200 RAM module is installed, the main memory
processing speed may become slower.
*17
Does not guarantee operation of all USB-compatible peripherals.
*18 <Only for North America>
The AC adaptor is compatible with power sources up to
240 VAC adaptor. This computer is supplied with a 125 V
AC compatible AC cord.
20-M-2-1
*19
Varies depending on the usage conditions, or when an
optional device is attached. Measured when the power saving
function on the USB2.0 USB Root Hub is set to on. (At the
time of purchase, the power saving function is activated.)
When Economy Mode (ECO) is enabled, the operating time
becomes approximately 20
% shorter than when it is disabled.
*20 Measured using BatteryMark™Version 4.0.1 (LCD bright-
ness : Maximum - Minimum).
*21 Measured using MobileMark™2005 (LCD brightness : 60
cd/m2).
*22 Varies depending on the usage conditions, CPU speed, etc.
It may take a long time to charge a fully discharged battery.
*23 Approx. 1.5 Wwhen the battery pack is fully charged (or not
being charged) and the computer is off.
*24 Rated power consumption.
23-E-1
*25 Average value. May differ depending on models.
*26 Operations of this computer are not guaranteed except for
the pre-installed OS.
*27 Preinstalled B’s CLiP does not support CD-R, DVD-R, +R
and DVD-RAM.
*28 Must be installed before use.
*29 The Product Recovery DVD-ROM is required.
*30 For startup methods, refer to “Hardware Diagnostics”.
*31 These are speeds specified in IEEE802.11a+b+g standards.
Actual speeds may differ.

10
2 Names and Functions of Parts
A :Speakers
B :Function Key
C :Keyboard
D :LED Indicator
: Caps lock
: Numeric key (NumLk)
: Scroll lock (ScrLk)
: Hard disk drive status
ECO : Economy Mode (ECO)status
: Battery status
E :Power Switch
Power Indicator
• Off: Power off/Hibernation
• Green: Power on
• Blinking green: Standby
F : Wireless Switch
<Only for model with wireless LAN/Bluetooth>
“Wireless LAN”
G :Latch
When closing the display, press down firmly from
above until the latch is firmly closed (locked).
CAUTION When closing the disk
cover, press down near the
drive power/open switch
(position of the arrow) to
ensure that the cover is
locked.
H :CD/DVD Drive
I : CD/DVD Drive Power/Open Switch
• Slide the switch to the right to open the disk cover.
• Slide the switch to the left to turn on/off the drive power.
CD/DVD Drive Indicator
• Off: Drive power is off.
• Green: Drive power is on, but the drive is not accessed.
• Blinking green: Drive power is on, and the drive is
being accessed.
J : LCD
K :LAN Port
If the Mini Port Replicator is connected to the computer,
connect the LAN cable to the LAN port on the Mini Port
Replicator. You cannot use the LAN port on the computer.
L : Modem Port
• Be sure to use the included modem telephone cable,
and insert the ferrite core side of modem telephone
cable into the modem port on the computer.
• Do not move/remove the ferrite core of modem tele-
phone cable.
M :USB Ports
N :Security Lock
You can connect a Kensington cable. Refer to the instruc
-
tion manual of the cable. The security lock and cable is a
theft prevention device. Matsushita Electric Industrial Co.,
Ltd. will bear no responsibility in the event of theft.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
90 mm {3.5 "} or less

11
A
B
C
E
F
G
K
J
I
H
EXT.
D
M
N
A :DC-IN Jack
B :Ventilation Hole
C :External Display Port
If the Mini Port Replicator is connected to the com-
puter, connect the external display to the external dis-
play port on the Mini Port Replicator. You cannot use
the external display port on the computer.
D :Mini Port Replicator Connector
Connect the Mini Port Replicator (optional).
E :Microphone Jack
A condenser microphone can be used. If other types
of microphones are used, audio input may not be pos-
sible, or malfunctions may occur as a result.
• When recording in stereo using a stereo microphone
Double-click in the notification area, click
[Options] - [Properties], and add a check mark for
[Recording], click [OK] - [Options] - [Advanced Con-
trols] - [Advanced], remove a check mark for [Mono
Microphone], and then click [Close].
• When using a monaural microphone with a 2-terminal plug
With the settings outlined above, only audio on the
left track will be recorded.
When monitoring the microphone audio using head-
phones, sounds on the left track cannot be heard,
regardless of the above settings. This is a result of the
computer’s specifications, and is not a malfunction.
F : Headphone Jack
You can connect headphones or amplified speakers.
When they are connected, audio from the internal
speakers is not heard.
G :SD Memory Card Slot
H :Bluetooth Antenna
<Only for model with Bluetooth>
I : Wireless LAN Antenna
J : Touch Pad
K :PC Card Slot
L : SD Memory Card Indicat
Blinking: During access
M :Battery Latches
N :Battery Pack
O :Emergency Hole
P :RAM ModuleSlot

Port
Replicator
Processor
ProcessorProcessor
Processor
System
SystemSystem
System Bus
BusBus
Bus
Included
L2-Cache 2M
DRAM
Interface
HostHub Bridge
Graphics
Interface
AGTL+
64bit
64bit64bit
64bit
667MHz(LV)
667MHz(LV)667MHz(LV)
667MHz(LV)
533MHz
533MHz533MHz
533MHz(ULV)
(ULV)(ULV)
(ULV)
1.05V
1.05V1.05V
1.05V
Yonah
YonahYonah
Yonah LV
LVLV
LV Dual Core
Dual CoreDual Core
Dual Core
Yonah ULV Single Core
Yonah ULV Single CoreYonah ULV Single Core
Yonah ULV Single Core
(479pin
(479pin(479pin
(479pin 

FCBGA)
FCBGA)FCBGA)
FCBGA)
Internal Core Frequency
Internal Core FrequencyInternal Core Frequency
Internal Core Frequency
HFM=
HFM=HFM=
HFM=1.6
1.61.6
1.66
66
6 G
GG
GHz
HzHz
Hz/LFM=
/LFM=/LFM=
/LFM=1.0 G
1.0 G1.0 G
1.0 GHz (High Model)
Hz (High Model)Hz (High Model)
Hz (High Model)
HFM=
HFM=HFM=
HFM=1.2
1.21.2
1.2 GHz/LFM=
GHz/LFM=GHz/LFM=
GHz/LFM=800
800800
800 MHz (Low Model)
MHz (Low Model)MHz (Low Model)
MHz (Low Model)
VCC Core
VCC CoreVCC Core
VCC Core
HFM=
HFM=HFM=
HFM=1.0V
1.0V1.0V
1.0V-
--
-1
11
1.2125
.2125.2125
.2125V/ LFM=
V/ LFM=V/ LFM=
V/ LFM=0.7625V
0.7625V0.7625V
0.7625V-
--
-1.0
1.01.0
1.0V
VV
V
Deeper Sleep=
Deeper Sleep=Deeper Sleep=
Deeper Sleep=0.55V
0.55V0.55V
0.55V-
--
-0.85
0.850.85
0.85V
VV
V (H
(H(H
(High Model
igh Modeligh Model
igh Model)
))
)
HFM=
HFM=HFM=
HFM=0.85V
0.85V0.85V
0.85V-
--
-1.1
1.11.1
1.1V/ LFM=
V/ LFM=V/ LFM=
V/ LFM=0.8
0.80.8
0.8-
--
-1.
1.1.
1.0
00
0V
VV
V
Deeper Sleep=
Deeper Sleep=Deeper Sleep=
Deeper Sleep=0.55
0.550.55
0.55V
VV
V-
--
-0.85V
0.85V0.85V
0.85V (L
(L(L
(Low Model
ow Modelow Model
ow Model)
))
)
VCCP
VCCPVCCP
VCCP 1.05
1.051.05
1.05V
VV
V
1.8V
1.8V1.8V
1.8V
64bi
t
6
4bi
t6
4bi
t
64bi
t
533MHz
533MHz533MHz
533MHz
CRT
ICH7
ICH7ICH7
ICH7-
--
-M
MM
M
USB
Interface
PCI
Express
Bridge
PATA
Interface
DMI x
DMI xDMI x
DMI x 2
22
2
1.5V 66MHz
1.5V 66MHz1.5V 66MHz
1.5V 66MHz
HD Audio
Interface
LPC
Bridge
LPC
LPCLPC
LPC Bus
BusBus
Bus 3.3V
3.3V3.3V
3.3V
Main Memor
Main MemorMain Memor
Main Memory
yy
y (
((
(DDR2
DDR2DDR2
DDR2-
--
- 533
533533
533)
))
)
On Board 512MB
On Board 512MBOn Board 512MB
On Board 512MB,
,,
,1GB
1GB1GB
1GB
Exten
ExtenExten
Extended
dedded
ded Memory
MemoryMemory
Memory (
((
(PC2
PC2PC2
PC2-
--
-4200
42004200
4200 )
))
)
Mi
MiMi
Micro
crocro
cro-
--
-DIMM
DIMMDIMM
DIMM 

1 (MAX
1 (MAX1 (MAX
1 (MAX 2
22
2GB
GBGB
GB)
))
)
Micro
p
hone
Head
p
hone
S
p
eakers
LCD
(TMD 1
11
14.1
4.14.1
4.1”
””
”SXGA+/XGA
SXGA+/XGASXGA+/XGA
SXGA+/XGA TFT
TFTTFT
TFT)
Int KB
Flat Pad
Storage Device
TYPE(SLOT A)
RJ-11
Card Bus
R5C811A
RICOH
RJ-45
PCI 2.3
PCI 2.3PCI 2.3
PCI 2.3 Bus
BusBus
Bus 32bit
32bit32bit
32bit 33MHz 3.3V
33MHz 3.3V33MHz 3.3V
33MHz 3.3V
Antenna
LAN(100Base)
RTL8101L
RealTek
MDC
Soft Modem
USB4
USB5
HD Audio / AC97
HD Audio / AC97HD Audio / AC97
HD Audio / AC97
SD Slot
(
SLOT B
)
USB2.0
1.8V/0.9V
1.8V/0.9V1.8V/0.9V
1.8V/0.9V
Calistoga
CalistogaCalistoga
Calistoga-
--
-GMS
GMSGMS
GMS
LVDS
(1ch/2ch)
RGB
AMP
EC/KBDC
M306KA
FWH
SST49LF008A
-33-4C-WHE
STAC9200
Sigmatel
DVD Multi
Drive
P
PP
PATA
ATAATA
ATA
HDD
HDDHDD
HDD
60
6060
60G
GG
G/
//
/120G
120G120G
120G
SD-IO Not Support
TPM
1.2
P
PP
PATA
ATAATA
ATA
(IDE)
5.3GByte/Sec
4.3GByte/Sec
4.3GByte/Sec
3.2GByte/Sec
1GByte/Sec
SATA
Interface
PCI
Bridge
PCI
PCIPCI
PCI Express x 4
Express x 4Express x 4
Express x 4 1.25GHz 1.5V
1.25GHz 1.5V1.25GHz 1.5V
1.25GHz 1.5V
998pin FCBGA
998pin FCBGA998pin FCBGA
998pin FCBGA
1.05V
1.05V1.05V
1.05V
652
652652
652 pin
pinpin
pin
BGA
BGABGA
BGA
1.05V
1.05V1.05V
1.05V
133MByte/Sec
2.5GByte/Sec
33.3MByte/Sec
(Ultra DMA Mode 2)
480MByte/Sec
SPI
Interface
SPI
SPISPI
SPI Bus
BusBus
Bus 3.3V
3.3V3.3V
3.3V
SPI Flash
8Mbit
25PE08
USB0
USB6
USB7
Port Replicator
CRT
RJ-45
Port
Replicator
BlueTooth
Mini Express Card Slot
W-LAN Golan 11ABG
USB2.0
USB1
USB
ATA
P
PP
PATA
ATAATA
ATA
(IDE) (USB3)
USB2
USB0
USB3
USB2
12
3 Block Diagram

13
4 Diagnosis Procedure
4.1. Basic Procedures

14
4.2. Troubleshooting
Pl as tak not of th following two points with r gard to troubl shooting:
1. Know-how of diagnosis upon occurr nc of h avy troubl s, .g. S t cannot b turn d ON , S t fails to start , No display on
scr n , tc.
2. Explanation of ach troubl , mainly symptom of troubl in op ration.
Flow Chart
NG
NO
YES
NO
YES
NG
NO
YES NG
OK
OK
NO
YES
NG
OK
NG
OK
NO
YES
OK
OK
NG
START
START
Pay att ntion to th following points wh n in pursuit of th caus of a troubl shooting.
1. P riph ral apparatus conn ct d with th s t should all b r mov d b for op ration ch ck.
2. Mak sur that cabl s, boards, tc. ar not coming off, and r ch ck th contact condition.
S t cannot b suppli d with curr nt.
Pow r lamp fails to light up.
AC
Adaptor/Batt ry
Output voltag R plac AC Adaptor/Batt ry
R turn s t-up utility s tpoint to th stat of d liv ry from factory .
Mak sur of contact of K/B conn ctor in us .
R plac k yboard or main board.
R plac DVD driv .
R plac main board.
R install HDD.
R plac main board.
Pow r lamp
ch ck
Ch ck contact condition of pow r input t rminal. R plac i
f
d f ctiv .
Ch ck Pow r SW. R plac if d f ctiv .
Inv rt r board R plac inv rt r board.
Ch ck inv rt r cabl continuity. R plac if d f ctiv
R plac LCD back light.
BIOS op ration
ch c
k
R plac main board (Ch ck fus at pow r sourc ).
LCD unit
ch ck R plac LCD unit.
R sult of
POST
R f r to POST
rror cod tabl . R plac main board.
Main board
ch ck R plac main board
HDD acc ss
Ch ck HDD cabl conn ction and continuity.
R plac if d f ctiv .
R plac HDD & R install.
R plac main board.
S t-up utility
starting R plac main board.
Troubl
symptoms on som
of DVD or CD
Ch ck if th r ar any flaws on DVD or CD
m dia. Sinc flaws may app ar on sp cifi
c
m dia, DVD or CD m dia can b d f ctiv .
START
END
Dark display on scr n.
Scr n fails to display.
Failur in starting
Not display d prop rly on scr n.
Som or all k ys cannot b input.
DVD/CD CALL not practicabl .
Starts but op rat s unstably.
H avy troubl .g.,
S t cannot b turn d
ON , S t fails to start ,
No display on
scr n , tc.
Each kind of
troubl in
op ration.
*Cl an DVD-ROM driv with an applicator.
LCD back
light lighting

15
5 Power-On Self Test (Boot Check)
Outline of POST
Th s t has a boot ch ck function call d POST (Pow r-On S lf T st) in it.
Th condition of th main body is diagnos d by ch cking b p sound or rror cod .
Start .............T st b gins automatically wh n pow r switch is s t to ON.
Normal finish .....Aft r m mory ch cking, a b p sound is issu d onc and th s t is plac d into automatic stop.
Not : If no rror occurs, nothing is display d. (No display of OK, tc.)
Error Diagnosis by Checking Beep Signal Sound
Th b p sound is as follows:
= long sound (about 0.4 s c.), = short sound (about 0.2 s c.), L ngth b tw n sounds is about 0.1 s c.
Table of errors classified by beep sounds
(1 (long sound) -2-3-4)
(L ngth of bar shows l ngth of sound.)
Diagnosis B p signal sound Error m ssag
1(long sound)-2 BIOS ROM rror
BIOS ROM rror
RAM rror
K yboard controll r rror
RAM rror
RAM rror
RAM rror
1-2-2-3
1-3-1-1
1-3-1-3
1-3-4-1
1-3-4-3
1-4-1-1
BIOS ROM rror2-1-2-3
Occurr nc of un xp ct d off ring2-2-3-1
Main board
(Not ) A b p sound is also issu d in cas of oth r I/O troubl .

16
6 List of Error Codes <Only when the port replicator is connected>
The following is a list of the messages that BIOS can display. Most of them occur during
POST. Some of them display information about a hardware device e.g. the amount of memory
installed. Others may indicate a problem with a device such as the way it has been configured.
Following the list are explanations of the messages and remedies for reported problems.
If your system displays one of except the messages marked below with an asterisk (*) write
down the message and contact Panasonic Technical Support. If your system fails after you
make changes in the Setup menus reset the computer enter Setup and install Setup defaults
or correct the error.
0200 Failure Fixed Disk
Fixed disk in not working or not configured properly. Check to see if fixed disk is attached
properly. Run Setup. Find out if the fixed-disk type is correctly identified.
0210 Stuck key
Stuck key on keyboard.
0211 Keyboard error
Keyboard not working.
0212 Keyboard Controller Failed
Keyboard controller failed test. May require replacing keyboard controller.
0213 Keyboard locked - Unlock key switch
Unlock the system to proceed.
0230 System AM Failed at offset : nnnn
System RAM failed at offset nnnn of in the 64k block at which the error was detected.
0231 Shadow AM Failed at offset : nnnn
Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.
0232 Extended AM Failed at offset : nnnn
Extended memory not working or not configured properly at offset nnnn.
0250 System battery is dead - eplace and run SETUP
The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup
to reconfigure the system.
*0251 System CMOS checksum bad - Default configuration used
System CMOS has been corrupted or modified incorrectly perhaps by an application program
that changes data stored in CMOS. The BIOS installed Default SETUP Values. If you do not
want these values enter Setup and enter your own values. If the error persists check the system
battery or contact Panasonic Technical Support.
0260 System timer error
The timer test failed. Requires repair of system board.
0270 eal time clock error
Real-time clock fails BIOS test. May require board repair.
*0280 Previous boot incomplete - Default configuration used
Previous POST did not complete successfully. POST loads default values and offers to run
Setup. If the failure was caused by incorrect values and they are not corrected the next boot
will likely fail. On systems with control of wait states improper Setup settings can also termi-
nate POST and cause this error on the next boot. Run Setup and verify that the wait-state
configuration is correct. This error is cleared the next time the system is booted.
0281 Memory Size found by POST differed from EISA CMOS
Memory size found by POST differed from EISA CMOS.

17
Troubleshooting
02D0 System cache error - Cache disabled
Contact Panasonic Technical Support.
02F0: CPU ID:
CPU socket number for Multi-Processor error.
02F4: EISA CMOS not writable
ServerBIOS2 test error: Cannot write to EISA CMOS.
02F5: DMA Test Failed
ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.
02F6: Software NMI Failed
ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).
02F7: Fail - Safe Timer NMI Failed
ServerBIOS2 test error: Fail-Safe Timer takes too long.
device address Conflict
Address conflict for specified device.
Allocation Error for: device
Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device.
Failing Bits : nnnn
The hex number nnnn is a map of the bits at the RAM address which failed the memory test.
Each 1 (one) in the map indicates a failed bit. See error 230 231 or 232 for offset address of the
failure in System Extended or Shadow memory.
Invalid System Configuration Data
Problem with NVRAM (CMOS) data.
I/O device I Q conflict
I/O device IRQ conflict error.
Operating System not found
Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed
disk and drive A: are properly identified.
Parity Check 1 nnnn
Parity error found in the system bus. BIOS attempts to locate the address and display it on the
screen. If it cannot locate the address it displays ????. Parity is a method for checking errors
in binary data. A parity error indicates that some data has been corrupted.
Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the
screen. If it cannot locate the address it displays ????.
Press <F1> to resume, <F2> to Setup
Displayed after any recoverable error message. Press <F1> to start the boot process or <F2> to
enter a Setup and change the settings. Write down and follow the information shown on the
screen.

18
7 Self Diagnosis Test
As for th s lf-diagnosis t st(PC-Diagnostic utility) to us this mod l, a standard t st and th
nhancing t st by th modul of th main body building in ar possibl .
Th pow r supply of th comput r is turn d on.
" F2 " is push d on th scr n of "Panasonic" whil " pr ss <F2 to nt r S tup> " is display d.
Th s tup utility starts and th n tak s not s of th cont nt of th BIOS s tup of pr s nt s t.
" F9 " is push d, " Y s" is s l ct d on th scr n of " Is th d fault valu load d? ", and " Ent r"
is push d.
" F10 " is push d.
" Y s" is s l ct d on th scr n of th s tup confirmation, and " Ent r" is push d.
Th comput r starts automatically.
1.
2.
3.
4.
5.
6.
7.
1.
2.
Not s
1-1. Setting of content of setup
1. Beginning of self-diagnosis test
If th d vic which can b s t is s t to "Invalidity" by "Advanc d" or "S curity" m nu, b com s an
rror by "PC-Diagnostic utility".
(It is judg d that th d vic which can b s t to "Invalidity" by "Main" m nu such as "Flat pad" is
normal if th controll r op rat s normally though s ts to "Invalidity" by th s tup. )
In th mod l with built-in DVD of th USB conn ction, v n if DVD is normal, b com s an rror if
l gacy USB is s t to "Invalidity"
Att ntion
Att ntion
"Ctrl" + "F7" is push d whil th "Panasonic" start scr n is display d aft r th comput r is start d.
Th t st of all d vic s b gins automatically by "PC-Diagnostic utility"’s starting.
It is a t st which th custom r who bought PC can x cut . (As for HDD, th nhancing t st is also
possibl .)
A flat pad do s not work for a whil aft r starting "PC-Diagnostic utility".
Th mov m nt of a flat pad might b com abnormal If aft r RAM b gins from th CPU/Syst m
t st, a flat pad will b op rat d in about 30 s conds. In that cas ,r starts pushing"Alt" + "Ctrl" +
"D l" k y. Or, pl as start "PC-Diagnostic utility" again aft r doing th pow r supply switch in th
slid , and turning off th pow r supply.
1-2. When you execute an automatic test
1.
2.
Pl as l t m discontinu diagnosing clicking to nd an automatic t st.
Pl as click on th charact r of "D" "PC-Diagnostic utility" on th scr n whil pushing both of right
"Shift" and l ft "Shift" k ys.
All d vic s which can s l ct th nhancing t st mak th s tting of th nhancing t st possibl .
Th district d vic is mad "FULL" display ( nhancing t st).
Th t st b gins clicking .
1-3. When you execute the enhancing test
3.
4.
5.
D
*Pl as r f r to it m 4 for th rror r sult of ach t st and th division of th br akdown part.
To skip BIOS password
Us <Ctrl>+<F10> k y to skip BIOS password or auth ntication of fing rprint.
This k y is only for nt ring DIAG mod . Not availabl to boot th comput r.
If custom r s t "HDD Lock", th DIAG program cannot p rform HDD t st.
*This k y is for s rvic purpos only. Do not disclos this information to unr lat d oth rs.

19
-Only th d vic which can b insp ct d on th ntir scr n is display d.
-Th it m do s not app ar wh n th d vic of wir l ss LAN tc. is not physically conn ct d.
-Th mov m nt of th it m must us an arrow k y or a flat pad.
-As for th d vic und r th diagnosis, blu and y llow ar alt rnat ly display d at th l ft of th icon.
- Th diagnosis r sult of th d vic gr ns at th l ft of th icon wh n it is normal, and b com s r d wh n
abnormal.
-Pl as click whil diagnosing wh n b ing stop on th way by th tim th t st of all d vic s nds.
-Pl as click wh n you r start "PC-Diagnostic utility".
*Each d vic is t st d from th b ginning, and it is not possibl to r start on th way.
-Wh n th t st of all d vic s nds, th t st r sult is display d und r th right of th scr n.
2. Operation of PC-Diagnostic Utility

20
1.
2.
3.
4.
5.
Turn d on th comput r.
"F2" is push d on th scr n whil "Pr ss<F2>to nt r S tup" is display d of "Panasonic".
Push "F10", and on th scr n of "Is th chang in th s tting pr s rv d and do nd?"and th n "Y s"
is s l ct d, and "Ent r" is push d.
Th comput r r activat s automatically.
Th nd option is chos n by th start m nu, and th pow r supply of th comput r is turn d off.
Ex.Th standard wh n th standard <all d vic > is t st d b com s 1+2+3=6 minut s.
Th r is gr atly a diff r nc from RAM t st wh n th m mory is incr as d according to th p rform-
anc of th m mory occasionally.
Mor ov r, wh n th main body of PC und r th t st is a high t mp ratur , it occasionally tak s tim .
Th r is gr atly a diff r nc from HDD according to th p rformanc of th driv occasionally.
2-3.The content of the setup is returned to the setting of the user
Standard at t st tim
All d vic s oth r than RAM and HDD
RAM standard t st
HDD standard t st
HDD nhancing t st (60GB)
about 1 minut
1 - 2 minut s
2 - 3 minut s
about 40 minut s
-To t st only a sp cific d vic , "T st" and "Do not t st" of ach d vic can b s l ct d.
-Th d vic which can s l ct th nhancing t st chang s in ord r of "Th standard is t st d" and "Do not
t st" wh n v r th d vic icon is click d.
2-1. Selection of tested device
Wh n of "Clos " on th right of th scr n is click d, th comput r r activat s automatically. Or, th
pow r supply switch is don in th slid and th pow r supply is turn d off.
2-2. "PC-Diagnostic utility" End method
Pl as b gin t sting clicking if th s l ction of th t st d d vic nds.
Start th standard t st Do not t st