Panasonic TH-32H410K User manual

-
LED TV
For the purpose of recycling to facilitate effective utilization of
Resources, please return this product to a nearby authorized collection
center, registered dismantler
or recycler, or Panasonic service center
when disposing
of this product.
Thank you for purchasing this Panasonic product.
Please read these instructions carefully before operating this product and
retain them for future reference.
The images shown
in this manual are for Illustrative purposes only.
English
Panasonic
Model No.:
TH-32H410K
TH-43H410K
Homr
The Adopted Trademarks HDMI, HDMI High-Definition
Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing Administrator, Inc.
in the United States and other countries.
ttDolby
AUDIO
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio and the double-D symbol are trademarks
of Dolby Laboratories Licensing Corporation.

Table of Contents
Chapter 1: Introduction
Warning ................................................................................................................................................ 3
Use Environment .................................................................................................................................. 4
Cleaning ............................................................................................................................................... 4
Hanging the
TV Set on the Wall ........................................................................................................... 4
Caution ................................................................................................................................................. 4
Symbol ................................................................................................................................................. 6
Precautions
for Using Remote Control ...... ................. .. . .. . .. . .. . .. . .. . .. . .. . .. . .. . .. ............... .. . .. . .. . .. . .. . .. . .. ... .. 6
Standard Accessories ........................................................................................................................... 7
Optional Accessories ............................................................................................................................ 7
Base Installation ................................................................................................................................... a
TV Controls .......................................................................................................................................... g
Installing/Removing Remote's Batteries ·····························································································
11
Remote Control.................................................................................................................................... 11
Chapter 2: Watching TV
Turning on or offthe TV ..................................• •·· •··· • •·· •··· •·· • •·· •··· • •·· •··· •·· • •·· • ··· • •·· •··· ··· · •·· •··· · ··· ···· ··· · •·· · ··· 12
Selecting the Input Source .................................................................................................................. 12
Selecting the Channel .......................................................................................................................12
Main Menu Operation ..........................................................................................................................12
Picture Menu ....................................................................................................................................... 12
Sound Menu ....................................................................................................................................... 13
Timer Menu ........................................................................................................................................ 14
Setup Menu ········
·· · ·· ··········· ·· · ·· · ·· ········ ·· · ·· · ·· · ·· ········ ·· · ·· · ·· · ·· ········ ·· · ·· · ·· · ·· ········ ·· · ·· · ·· · ·· ········ ·· · ·· · ·· · ·· ·········· 14
Lock Menu .
... . ... .... ... . ... ..... ... .... ... . ... ..... ... .... ... . ... ..... ... . ...... . ... ..... ... . ... .... ... ..... ... . ... .... ... ..... ... . ... .... ... . ... 15
Channel Menu ...................................................................................................................................
·· 15
Chapter 3: Using Media Player
Preparation ..........................................................................................................................................16
Media Operation...................................................................................................................................15
Photo Control Menu..............................................................................................................................16
Movie Control Menu ·····························································································································16
Music Control Menu:
.. ,..........................................................................................................................17
Chapter 4: Technical Information
Supported File Format in Media Player .............................................................................................. 18
Maintenance ....................................................................................................................................... 20
Troubleshooting .................................................................................................................................. 20
Specifications ......................................................................................................................................
21
Note:
1. The graphics in this manual are only forreference.
2. Your TV may be slightlydifferent from that shown in this manual.
3. Designs andspecifications are subject to change without notice.
4. In dry environment due to static electricity, the product may restart and return to the main OSD
interface, USB playerinterface or the previous source mode. It is normal andplease continue to
operate the
TV.
2

Introduction
.A. Warning
Handling the mains plug and lead
Insert the mains plug fully into the socket outlet. (Ifthe mains plug is loose, it could generate heat and cause fire.)
Ensure that the mains plug is easily accessible.
Do not touch the mains plug with a wet hand. (This may cause electrical shock.)
Do not use any mains lead other than that provided with this TV. (This may cause fire or electrical shock.)
Do not damage the mains lead.
(A damaged lead may cause fire or electrical shock.)
• Do not move the
TV with the lead plugged in the socket outlet.
• Do not place a heavy object on the lead
or place the lead near a high-temperature object.
• Do not twist the lead, bend it excessively
or stretch it.
•Do not pull
on the lead. Hold onto the mains plug body when disconnecting the lead.
• Do not use a damaged mains plug
or socket outlet.
100 - 240V -50 / 60 Hz
If you find any 1111
abnormality, remove the 8111 -~
mains plug immediately! .... ~ ..
• Mains plug types vary between countries.
Power source Do not insert external objects into the TV
•This TV is designed to operate on • Do not allow any objects to drop into the TV through the
•
100 - 240V - 50/60 Hz
air vents. (Fire or electrical shock may result.)
•
Table-top use/Wall hanging
Do not place the TV on sloped or unstable
Do not use External Voltage Stabilizer with surfaces, and ensure that the TV does not
the TV set hang over the edge of the base
•Inferior Quality stabilizer may cause damage to the TV. •The
TV may fall off or tip over.
•Warranty is not valid
if external stabilizer is used. Use only the dedicated pedestals/
Do not remove covers and NEVER modify mounting equipment
• Using an unapproved pedestal or other fixtures may
the TV by yourself make the
TV unstable, risking injury. Be sure to ask your
•Do not remove the rear cover as live parts are accessible local Panasonic dealerto perform setup.
when it is removed. There are no user serviceable parts • When mounting the product on a wall
or ceiling,
inside. (High-voltage components may cause serious be sure to install the product according to the
electrical shock.) method recommended by the manufacturer. This
• Have the
TV checked, adjusted, or repaired at your local
is a safety feature.
Panasonic dealer. • Only use attachments/accessories specified
or
• Please refer the information on exterior back enclosure provided by the manufacturer (such as the exclusive
for electrical and safety information before installing supply adapter, battery etc).
or operating the apparatus.
• The mains plug
is used as disconnect device, the Do not expose to direct sunlight and other
disconnect device shall remain readily operable. sources
of heat
Do not expose to rain or excessive • Avoid exposing the
TV to direct sunlight and other
sources
of heat.
moisture © To
prevent the spread of
•To prevent damage which might result in electric shock or
fire, do not expose this TV to rain or excessive moisture. fire,
keep candles or other
This TV must not be exposed to dripping or splashing
open flames away from
water and objects filled with liquid, such as vases, must
this product at all times.
not be placed on top of or above the TV.
3

Use Environment
A Stability Hazard
A television set may fall, causing serious personal injury or
death. Many injuries, particularly to children, can
be avoided by
taking simple precautions such as:
ALWAYS use cabinets orstands or mounting methods
recommended by the manufacturer ofthe television set.
ALWAYS use furniture that can safely support the television
set.
ALWAYS ensure the television set is not overhanging the
edge ofthe supporting furniture.
ALWAYS educate children about the dangers ofclimbing on
furniture to reach the television set or its controls.
ALWAYS route cords and cables connected to your
television so they cannot
be tripped over, pulled or grabbed.
NEVER place a television set
in an unstable location.
NEVER place the television set
on tall furniture (for
example, cupboards or bookcases) without anchoring both
the furniture and the television set
to a suitable support.
NEVER place the television set
on cloth or other materials
that may
be located between the television set and
supporting furniture.
NEVER place items that might tempt children
to climb, such
as toys and remote controls,
on the top ofthe televison or
furniture
on which the television is placed.
Ifthe existing television set
is being retained and relocated, the
same considerations as above should
be applied.
Cleaning
• Do not spray water or
detergent directly
on TV
screen for cleaning purpose.
Leaking liquid substance will
cause damage to TV.
• Be careful of cats, rats or other (S)tO]
animals that may urinate on
the TV (front and rear). It may
lead to TV failure.
•
Do not use sharp or hard objects (finger nails, knife
and etc.) on TV screen. This may cause damage to
the screen surface.
Hanging the TV Set on the Wall
• Check that the wall can support the weight of the TV set
and wall mount assembly.
• Follow the mounting instructions provided with the wall
mount.
• The
TV set must be installed on a vertical wall.
• Make sure to use only screws suitable for the material
of
the wall.
• Make sure that the TV set cables are placed so that there
is not danger of tripping over them.
All other safety instructions about our
TV sets are also
applicable here.
Warning: This operation requires two people.
To ensure a safe installation, observe the following safety.
A Caution
1.Read these instructions---AII operating instructions
must be read and understood before the product is
operated.
4
2.Keep these instructions---These safety and
operating instructions must be kept in a safe place for
future reference.
3. Read all warnings---AII warnings on the product and
in the instructions must be observed closely.
4.Follow all instructions--AII operating instructions
must be followed.
5.Attachments---Only use attachments/ accessories
specified by the manufacturer. Do not use attachments
not recommended by the manufacturer. Use of
improper attachments can result in accidents.
6.Power source---This product is intended to be
supplied by a listed power supply indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or
local power company. For added protection for this
product during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the cable
system.
Do not defeat the safety purpose of the polarized or
grounding plug. A polarized plug has two blades with one
wider than the other. A grounding plug has two blades and
a third grounding prong. The wide blade
or the third prong
is provided for your safety. Ifthe provided plug does not fit
into your outlet, consult
an electrician for replacement of
the obsolete outlet.
7.Power cord protection--.Protect the power cord from
being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they
exit from the apparatus.
Note: Where the mains plug or an appliance
coupleris used
as the disconnect device, the
disconnect device shall remain readily operable.
8.Overloading---Do not overload wall outlets, extension
cords, or convenience receptacles on other equipment
as this can result in a risk of fire or electric shock.
9.Servicing---Refer all servicing to qualified service
personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
10.Damage requiring service---lf any of the following
conditions occurs, unplug the power cord from the AC
outlet, and request a qualified service person to
perform repairs.
a.When the power cord or plug is damaged.
b.When a liquid is spilled on the product or when objects
have fallen into the product.

c.When the product has been exposed to rain or water.
d.When the product does not operate properly as
described in the operating instructions.
Do not touch the controls other than those described in
the operating instructions. Improper adjustment of
controls not described in the instructions can cause
damage, which often requires extensive adjustment
work by a qualified technician.
e.lf the product has been dropped or the cabinet has
been damaged in any way.
f.When the product displays an abnormal condition
or
exhibits a distinct change in performance. Any
noticeable abnormality
in the product indicates that the
product needs servicing.
11.Replacement parts---ln case the product needs
replacement parts, make sure that the service person
uses replacement parts specified by the
manufacturer,
or those with the same characteristics
and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock
and/or other danger.
12.Safety checks--Upon completion
of service or
repair work, request the service technician to perform
safety checks to ensure that the product is
in proper
operating condition.
13. Stand---Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold with
the apparatus. Do not place the product on an
unstable trolley, stand, tripod or table. Placing the
product on an unstable base can cause the product
to fall, resulting
in serious personal injuries as well as
damage to the product. When mounting the product
on a wall,
be sure to follow the manufacturer's
instructions. Use only the mounting hardware
recommended by the manufacturer.
14.Careful move--When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from lip-over. Sudden stops, excessive
force and uneven floor surfaces can cause the
product to fall from the trolley.
Neverattempt to move the TV unless the AC power
cord has been disconnected.
5
15.Lightning---Unplug this apparatus during lightning
storms or when unused for long periods
of time.
For added protection for this television equipment
during a lightning storm,
or when it is left unattended
and unused for long periods
of time, unplug it from
the wall outlet and disconnect the antenna. This will
prevent damage to the equipment due to lightning
and power-line surges.
16.Panel protection---The display panel used
in this
product is made
of glass. Therefore, it can break
when the product is dropped or impacted upon by
otherobjects. Be careful not to be injured by broken
glass pieces
in case the display panel breaks.
17.Pixel defect---The display panel
is a very high
technology product, giving you finely detailed pictures.
Occasionally, a few non-active pixels may appear on
the screen as a fixed point
of blue, green or red.
Please note that this does not affect the performance
of your product.
18. Do not block the rear air vents
• Adequate ventilation is essential to prevent failure
of
electronic components.
• Ventilation should not be impeded by covering the
ventilation openings with items such as newspapers,
table cloths and curtains.
•We recommended that a gap of at least 10 cm is left all
around this
TV even when placed inside a cabinet or
between shelves.
•When using the pedestal, keep the space between the
bottom
of the TV and the surface where the TV is set.
•If pedestal is not used, ensure the vents is the bottom of
the TV are not blocked.
• Do not install this equipment in a confined or building-in
space such as a book case or similar unit, and remain a
well ventilation conditions
at open site.
Minimum distance
D E
(cm)
Note: The picture is only for reference.
19. Do not ingest the battery, Chemical Burn Hazard--
Keep new and used batteries away from children. If the
battery compartment does not close securely, stop using
the product and keep it away from children. If you think
batteries might have
been swallowed or placed inside any
part ofthe
body, seek immediate medical attention.

20. Listening--- Listening to music at high volume levels
and for extended durations can damage one"s hearing.
In order to reduce the risk of damage to hearing, one
should lower the volume to a safe, comfortable level,
and reduce the amount oftime listening at high levels.
Symbol
For the terminals marked with symbol of" i"may be of
sufficient magnitude to constitute a risk of electric shock.
The external wiring connected to the terminals requires
installation by an instructed person
or the used of
ready-made leads or cords.
If the product has the symbol
[g] in its rating label and
the power cord has two pins, it means that the equipment
is a Class
II or double insulated electrical appliance. It
has been designed in such a way that it does not require
a safety connection to electrical earth.
The following information are recommended to be
included where applicable:
...,. Refers to alternating current(AC).
Refers to direct current(DC).
1§1 Refers to Classll equipment.
<.!) Refers to stand-by.
I Refers to power ON.
7 Refers to dangerous voltage.
ATTENTION:RISQUE DE CHOC EL.ECTRIQUE-NE PAS OUVRIR.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence
of non-insulated "dangerous voltage" within
the product's enclosure that may be
of sufficient
magnitude to constitute a risk
of electric shock.
To reduce the risk of electric shock. Do not remove
cover (
or back). No user serviceable parts inside.
Refer to qualified service personnel.
The exclamation point within an equilateral triangle is
intended to alert the userto the presence
of important
operating and maintenance instructions in the literature
accompanying the appliance.
6
Precautions for Using Remote Control
Use the remote control by pointing it towards the
remote sensor. The items between the remote
control and the remote sensorwill interfere the
normal operation.
Do not make remote control vibrate violently. Also,
do not splash liquid on the remote control, also do
not put the remote control in high humidity place.
Do not place remote control under direct sunlight
which will cause deformation
of the unit by heat.
When the remote sensor
is under direct sunlight or
strong lighting, the remote control will do not work.
If so please change the lighting or TV's position, or
operate the remote control closer to the remote
sensor.

Standard Accessories
Remote Control Pedestal (2) Screws (214) Batteries (2) Operating
(AA size) Instructions
I
!\
32.\
~
~~
~
•
) \ 32": 2 PCS
43": 4 PCS
~-:==
43"
Note:
1) The pictures are onlyfor reference.
2) Accessories may notbe placedall together. Take care not to throw them away unintentionally.
3) This product contains possibly dangerous parts (such as plastic bags), that can be breathed in or swallowed by young
children accidentally. Keep these parts out
of reach of young children.
Optional Accessories
Please contact your local Panasonic dealer to purchase the recommended optional accessories. For additional details,
please read the manual of optional accessories.
Wall-hanging bracket
Please contact your local Panasonic dealerto purchase the recommended wall-hanging bracket.
• Screw Specifications
Screw Spec.
32"
43"
Top Down Top
E "Diameter" (mm) M4
M4 MS
D "Depth" I Max. 9 9
15
(mm)
I Min. 7 7
12
Quantity 2 2 2
• VESA
Size
32" 43"
a(mm) 200 200
b(mm) 200 200
Note: The graphics are only for reference.
A.(Warning)
Down
MS
15
12
2
Failure to use a Panasonic bracket or choosing to mount the unit yourself will be done at the risk of the consumer.
Always
be sure to ask a qualified technician to carry out set up. Incorrect fitting may cause equipment to fall, resulting
in injuryand product damage. Any damage resulting from not having a professional installer mount your unit will void
your warranty.
•When any optional accessories
or wall hanging brackets are used, always ensure that the instructions provided are
followed fully.
•Do not mount the unit directly below ceiling lights (such as spotlights
or halogen lights) which typically give off high
heat. Doing so may warp
or damage plastic cabinet parts.
•Take care when fixing wall brackets to the wall. Wall mounted equipment shall not be grounded by metal within the wall.
Always ensure that there are no electrical cables
or pipes in the wall before hanging bracket.
•To prevent fall and injury, remove the TV from its fixed wall position when it is no longer
in use.
7

Base Installation
.A. (Warning )
Do
not disassemble or modify the pedestal.
• Otherwise the TV may fall over and become damaged, and
personal injury may result.
.A. ( Caution )
Do
not use any pedestal other than the one provided
with this TV.
• Otherwise the TV may fall over and become damaged, and
personal injury may result.
Do not use the pedestal if it becomes warped or
physically damaged.
• If you use the pedestal while it is physically damaged,
personal injury may result. Contact your local Panasonic
dealer immediately.
During set-up, make sure that all screws are securely
tightened.
• If insufficient care is taken to ensure screws are properly
tightened during assembly, the pedestal will not
be
strong enough to support the TV, and ii might fall over
and become damaged, and personal injury may result.
Ensure that the TV does not fall over.
• Ifthe TV is knocked or children climb onto the pedestal
with the
TV installed, the TV may fall over and personal
injury may result.
Two or more people are required to install and
remove the TV.
• If two or more people are not present, the TV may be
dropped, and personal injury may result.
When removing the pedestal from the TV, do not
remove the pedestal by the methods other than the
specified procedure.
• Otherwise the TV and / or pedestal may fall over and
become damaged, and personal injury may result.
Appearance of the product in illustrations may differ
from
your actual product, and is for reference
purposes only.
Removing the pedestal from the
TV
Be sure to remove the pedestal in the following way when
using the wall-hanging bracket
or repacking the TV.
1 Remove the assembly screws from the TV.
2 Remove the pedestal from the TV.
8
1. Please take out the accessory bag from the package
and check ifall bellow parts exist without missing,
ifnot, please contact your local dealer.
Base A Base B Base A Base B
Screw (2 pcs) Screw (4 pcs)
Note: The pictures are only for reference.
2. Take out the TV and carefully put it (screen downward)
on a stable and flat table with a soft cloth
or cushion on
it.
3. Connect the TV and base by putting and fastening
matched screws into the holes.
(32")
(43")

TV Controls
• Power Indicator
Front View
Power Indicator
Note: The picture is onlyforreference.
• Lit in red: Standby mode.
• Lit in green: Working status.
• Unlit: Powered off.
• Rocker Button
Bottom View
\ I
., _::rnr: :::;; : :! ;\ : ;; ; ::: '' .; .: : .. i: ::f/
F;; ~ Middle
Left - I.' ,.\. { j; ).. :,- ,Right
Backward
Note: The picture is onlyforreference.
• Press Middle:
1. In standby mode, press it to turn on the TV.
2. Without OSD, short press itto access source
menu; long press to turn the
TV to standby mode.
3. With OSD, short press itto confirm a selection;
long press it to exit the OSD.
• Push Left: Decrease volume or goto left.
• Push Right: Increase volume orgo to right.
• Push Backward: Channel up or go to above.
• Push Forward: Channel down orgo to below.
9
• TV Terminals
2
Back View
4
6
"!I
NI
.. ,
"' '
"'
;;
~
Ns
~j
z
:!
w~
Z=>
:,o
Note: The picture is onlyforreference.
1. USB 1
Connect USB devices to the TV.
ml
l
i
'
Note:
1) The picture is only for reference.
3
5
2) Neverremove the USB device or turn off the N
while using the USB device.
2. ANTENNA
IN
Connect a coaxial cable to receive signal from
the antenna
or cable.
Antenna or cable TV
Note:
1) The picture is onlyforreference.
2) Do not place the RF cable underthe N.
3) To obtain the optimum quality of picture and sound,
the correct cable
(750 coaxial} and the correct
terminal are required.
4)
If a communityantenna system is used, you may require
the correct connection cable
and plug between the wall
aerialsocket
and the N.

5) Yourlocal Television Service Center or dealer may be
able to assist you in obtaining the correct aerialsystem
for your particular area and the accessories required.
6) Any matters regarding aerial installation, upgrading of
existing systems or accessories required, and the costs
incurred, are the responsibility
of you, the customer.
3. DIGITAL AUDIO OUT
Output the TV's digital audio signal to a compatible
audio receiver.
ra,
l!!.I
Digital audio device
Note: The picture is only for reference.
4. HDMI 1/2
Receive HDMI input signal from signal source
such as DVD.
Recorder/Player
Camoorder
Note:
1) The picture is only for reference.
2)
If the external device has a OVI output only, use a
OVI to HOM/ adapter cable to connect to the HOM/
terminal.
3)
For the audio receivercontrol Sound Out, firstly you
must have a device which supports HOM/ Sound Out,
then connect
it to the HOM/2 port. When "Sound Out"
setting is enabled on your T\I, the TV's speakers will
be muted automatically and audio will be outputted
on your sound device system.
10
5.AVIN
Receive audio and video signal from signal source
such as DVD.
~:. I L::j
VCR
Game console
Note: The picture is only for reference.
6. LINE OUT
Speakers won't be muted, and sound level is fixed.
~
:,
0
Note:
1) The picture is only for reference.
~
~
Analogue audio device
2) When using a headphone, adjustits volume to avoid
excessive volume levels, as hearing damage may result.
• Power Connection
Note: The picture is only for reference.
Connect the power cord to the power outlet
(100-240V - 50/60Hz).

Installing/Removing Remote's Batteries
2
11] _____ _
Match the correct polarity(+/-)
A. ( Caution )
• Incorrect installation may cause battery leakage and corrosion, resulting in damage to the
remote control.
• Do not mix old and new batteries.
• Replace only with same
or equivalent type. Do not mix different battery types (such as
alkaline and manganese batteries).
• Do not use rechargeable (Ni-Cd) batteries.
• Do not burn
or break up batteries.
• Do not expose batteries to excessive heat such as sunshine, fire
or the like.
• Make sure you dispose
of batteries correctly.
Note: The picture is only
for reference.
• Ensure batteries are replaced correctly, there is danger
of explosion and fire ifbattery is
reversed.
• Do not disassemble
or modify the remote control.
Remote Control
1. POWER: Turn on the TV or turn it to standby mode.
2. AV: Select the input source.
3. MEDIA PLAYER: Access the interface of media player.
4. TV: Change to the TV source.
5. MENU: Access the main menu.
6. GUIDE: Access the electronic program guide.
7. TEXT: Turn on or turn offthe teletext function.
8. STTUAD: Turn on or turn offthe function of subtitle or
audio description.
9. INFO: Show the detailed information.
10. EXIT: Exit the current operation.
11. Navigation Buttons (iii.IT/•/• ): Navigate the menu.
12. OK: Enter, confirm or execute your selection.
13. OPTION: Access the quick menu.
. 2abc 3def \ 14: RETURN: Back to the upper-level menu. 15: Color Buttons (RED/GREEN/YELLOW/BLUE):
L______J I....__________ ~
Sjkl· 6mno \
~ ..___________, ~
Execute the prompt function in specific mode.
16. VOL+/-: Increase or decrease the sound volume.
&uv 9wxyz I
L________J ~ •
.............. .,.
17. CH A/V: Change to the next or previous channel.
18. ASPECT: Select the aspect ratio.
STILL : O : O 19. MUTE: Mute or restore the sound.
,............; bi:STVIEW
20. Number Buttons (0-9) or Letter Buttons (a-z):
Input the numbers or alphabetical letters.
21. STILL: Freeze or unfreeze the picture.
22. LAST VIEW: Return to the previously-viewed channel.
Note: The picture is only for reference.
11

Watching TV
Turning on or offthe TV
1. Connect the power cord to the power outlet.
2. In standby mode, press POWER button to turn on the TV.
3. In working status, press POWER button to turn the TV to
standby mode.
4. Disconnect the power cord to power off the TV
completely.
Selecting the Input Source
1. Press AV button to access the list of input sources.
2. Press J,,,/T or AV button to select the desired input
source.
3. Press OK button to access the selected input source.
Input
Note: The picture is onlyforreference.
Selecting the Channel
1. Press Number Buttons (0-9) to change to the desired
channel directly.
2. Press CH A/v button to change to the next or previous
channel.
3. While watching DTV programs, press GUIDE button to
access the program guide which will show the program
list
of different channels of eight days from the current
date on.
• Press YELLOW button to change to the previous day.
• Press BLUE button to change to the next day.
• Press J,,,/T button to select the desired channel.
4. While watching TV programs, press OK button to access
the channel list. Press
1,,,/T button to select the desired
channel.
12
Main Menu Operation
Step 1: Press MENU button to access the main menu.
Step 2: Press J,,,/T button to select a submenu: Picture,
Sound, Timer, Setup, Lock
or Channel, and
press OK button to enter.
Step 3: Press J,,,/T button to select an item, and press OK
button to enter.
Step 4: Press J,,,/T or •/• button to adjust the selected
item.
Step 5: Press RETURN button to back to the upper-level
menu.
Step 6: Press EXIT button to exit the main menu operation.
Note: Some items may not be available for some countries,
some models or some sources.
Picture Menu
~- ""
""""o: '.'.',',"'
~,lef1
"""o: '.'.',',"'
Note: The pictures are only forreferences.

• Picture Mode
Select the desired picture mode. Choices are Standard
Mild, User and Dynamic. It will automatically skip to "U~er"
mode if you adjust one
of the following 6 items including
Contrast, Brightness, Colour, Tint, Sharpness and
Backlight.
• Contrast
Adjust the difference between light and dark areas of the
picture.
• Brightness
Adjust the lightness of the picture.
• Colour
Adjust the colour richness of the picture.
• Tint
Adjust the colour tint of the picture. It is only available for
NTSC system.
• Sharpness
Adjust the edge of the picture.
• Backlight
Adjust the brightness of the screen.
• Colour Temperature
Adjust the overall colour tone ofthe picture. Choices are
Medium, Warm and Cool.
• Aspect Ratio
Select the desired aspect ratio. The choices differ by
different input sources.
• For DTV, choices are: 16:9/Zoom1/Zoom2/Auto/4:3.
• For ATV &AV, choices are 16:9/Zoom1/Zoom2/4:3.
• For HDMI, choices are 16:9/Zoom1/Zoom 2/4:3/
Just Scan.
• For USB, the choices are 16:9/4:3/Auto.
• Noise Reduction
Reduce the noise in the picture signal. Choices are Middle
High, Off and Low. '
• MPEG Noise Reduction
Reduce the noise created while converting or compressing
MPEG picture signal. Choices are Middle, High, Off and
Low.
• Reset to Defaults
Reset picture settings of the current source to default values.
13
Sound Menu
,,1en
, · --·•: '.'. ' ,',"
Note: The picture is onlyforreference.
• Sound Mode
Select the desired sound mode. Choices are Standard
News, User, Music and Movie. It will automatically skip to
"User" mode
if you adjust one of the following 3 items
including Bass, Treble and Balance.
• Bass
Adjust the lowerfrequency of the sound.
• Treble
Adjust the higher frequency ofthe sound.
• Balance
Control the balance between left and right speakers.
• Auto Volume
Turn on to adjust the sound volume depending on the input
signal.
• Surround
Help to create rich and wider sound from stereo sound
sources.
• SPDIF MODE
Select the desired SPDIF mode between PCM and Auto.
• Reset to Defaults
Reset all sound settings to the default values.

Timer Menu
Sele'1
"'"o: ;: ·: "
Note: The picture is only for reference.
• Timezone
Select the time zone.
•Auto Sync
Select to adjust the TV clock automatically or manually.
• Clock
Setup or display the date and time.
• Sleep Timer
Setup the timer to turn offthe TV automatically. Choices
are Off, 15min, 30min, 45min, 60min, 120min and
180min.
•Auto Sleep
Setup the timer to turn offthe TV automatically when there
is no operation during the selected time. Choices are Off,
4Hours, 6Hours and 8Hours.
• OSDTimer
Select the time to keep the menu display without
disappearing. Choices are
55,105,205, 25S and 305.
14
Setup Menu
Note: The picture is only forreference.
• OSD Language
Select the desired OSD language.
• Audio Languages
Select the primary and secondary audio languages. It is
only available for DTV source.
• Subtitle Languages
Select the primary and secondary subtitle languages. It is
only available for DTV source.
• Restore Factory Default
Reset all menu settings to the default values.
Note:
All user data will be lost after operating this function.
• Link
Setup to control the connected HDMI device.
• HDMI Link: Turn on or turn offthe HDMI link function.
• Sound Out: Turn on or turn offthe function of Sound
Out
in HDMl2.
• Auto Standby: Turn the connected HDMI device to
standby mode automatically when you turn offthe
TV.
• Device List: Display the list of HDMI devices
connected to the
TV.
• Location
Select the TV environment between Shop and Home.
• Home Mode:
You would be able to view the standard
settings for Picture and Sound modes.
• Shop Mode: You can enjoy enhanced setting for
Picture and Sound modes.
• Software Update (USB)
Update the TV software system by connecting an USB
device with new software.
• Input
Select the input sources.
• Standby Auto Tuning
Search for DTV programs automatically when the TV turns
standby. It is only available for some countries.

Lock Menu
S 1. ,
"'""@" '""
•i,!]lk'
Note: The picture is only for reference.
• Lock System
Turn on
or turn offthe lock system.
• Set Password
Change the password as you like. The default password
is
0000.
Note:
If you change the password and forget it, you can
use the superpassword 8899 to enter the lock system.
• Channel Lock
Restrict unauthorized access to specific channels based
on the channel information. Password
is needed to view
locked channels. It is only available for TV source.
• Key Lock
Disable the function
of rocker button.
• Parental Guidance
Restrict unauthorized access to programs which are not
suitable for children based on age rating. Password
is
needed to view locked programs. It is only available for
TV source.
Channel Menu
,,10,
,, .... : '.'.','."
Note: The picture is onlyforreference.
15
• Auto Tuning
Search for channels automatically. Before searching, you
may need to adjust some settings ( select tune type, select
your country
or input your local postal codes) which may
vary by different countries. Press EXIT button select
whether
or not to exit auto tuning. The searched channels
will be saved
in the TV automatically after auto tuning is
finished.
• DTV Manual Tuning
Search for DTV channels Manually. Before searching, you
may need to select the channel number. The search stops
automatically when a program is found and the program
will be saved
in the selected channel position automatically.
Press EXIT button to exit DTV Manual Tuning.
• ATV Manual Tuning
Search forATV channels manually. Before searching, you
may need to select the channel number (Storage
To &
Current CH)
or Sound_Standard. Select Scan Search
and press
•/• button to start the search.
• Press • button to search towards the lowerfrequency.
• Press • button to search towards the higher frequency.
The search stops automatically when a program is found
and press RED button to save the program. Press EXIT
button to exit ATV Manual Tuning.
• Fine Tuning: Select aATV channel you want, press
•/• button to make small adjustments until the picture
and sound are as good as you like. Fine tune is not
necessary under normal conditions. However,
in area
of inferior broadcast conditions where adjustments are
necessary for a better picture and sound, please use
fine tune.
• Programme Edit
Press color buttons to edit the programs.
• Press RED button to delete a program.
• Press GREEN button to rename a program. This
is only
available forATV source.
• Press YELLOW button to move a program.
• Press BLUE button to skip a program.
• Signal Information
Show the detailed information of current signal. It
is only
available for DTV source.
• Software Update (OAD)
Turn on to update the
TV software system by OAD code
stream over the air. II is only available for DTV source.
• OAD Scan
Scan for available OAD code stream. It is only available
when Software Update (OAD)
is turned on. It is only
available for DTV source.
• EWS Local Postal Codes
Use number buttons
(0-9) to input your local postal codes.
It is only available for Indonesia.

Using Media Player
Preparation
• Insert your USB device on the TV to view compatible
photo and movie
on the TV screen or play compatible
music through the
TV.
• If the connected USB hard disk does not have an
external power source, it may not be detected. Be sure
to connect the external power source.
•
To avoid losing the data on your USB device or damaging
your USB device, it is recommended that
you back up all
data on your USB device.
• The control menu displays
in media player may differ by
different regions or models. And please take your actual
TV as the standard.
• If you want to pull out your USB device, please exit USB
mode firstly.
• For instructions
on using your USB device, refer to the
owner's manual
of your USB device.
• Never remove the USB device or turn off the TV while
using the USB device. Doing so may result
in loss of data
or damage to the USB device or the
TV.
• Certain types of USB devices may not be compatible
with the
TV.
Media Operation
Note: The picture is only for reference.
Step 1: Press MEDIA PLAYER button to enter the
interface of media player. Or select USB
source in input source list and press OK button
to enter.
Step 2: Press •/• and OK buttons to select and enter
a media type: PHOTO, MOVIE or MUSIC.
Step 3: Press J,,,/T / •/• and OK buttons to select the
desired media file with the same type as you
have
selected in Step 2.
Step 4: Press OK button to start playing the media file.
Step 5: Press EXIT button to exit the playing.
16
Photo Control Menu
While browsing a photo, press OK button to
display the photo control menu, and press T button to
exit it. Press •/• button to select the icon of desired
function and press OK button to execute it.
Play/ Pause
Go to the previous / next photo.
Stop playing.
Repeat mode selection. Highlight this icon and
continue pressing OK to select Repeat
1,
RepeatALL or Repeat NONE.
Display the current photo information.
Rotate the photo clockwise / counterclockwise
by
90 degrees every time the button is pressed.
•• Zoom in / zoom out the photo.
Move View (left, right,
up, down). You can use
Move View only when the photo is magnified.
Note: The pictures are only forreferences.
Movie Control Menu
While watching a movie, press OK button to
display the movie control menu, and press T button to
exit ii. Press •/• button to select the icon of desired
function and press OK button to execute it.

Play/ Pause
Fast backward I fast forward.
Go to the previous/ next movie.
Stop playing.
Repeat mode selection. Highlight this icon and
continue pressing OK to select Repeat
1,
RepeatALL or Repeat NONE.
Display the current movie file information.
Input the time you want and skip to play from
the input time.
Setup the aspect ratio.
Note: The pictures are onlyforreference.
Music Control Menu
While playing music, press OK button to
display the music control menu, and press T button to
exit it. Press •/• button to select the icon of desired
function and press OK button to execute it.
Play/ Pause
Fast backward I fast forward.
Go to the previous/ next music.
Stop playing.
Repeat mode selection. Highlight this icon and
continue pressing OK to select Repeat
1,
RepeatAll or Repeat None.
Display the current music file information.
Note: The pictures are onlyforreference.
17
Note:
1. Underthe following conditions, this system cannot
decode the file
and the file cannotbe played normally:
-The parameters
of file, such as the pixel of picture,
code rate
of audio and video file, sampling rate of
audio file, exceed the limit of the system;
-The format
of file is notmatched or the file is harmed.
Note: The code rate this system supports does not
exceed 20Mbps.
2. Hotplug: Do not disconnect when the system is
reading
or transmitting data, avoiddamaging the
system
or the device.
3. Pay attention to the power supply of the device when
you are using a mobile hard disk
or a digital camera.
If the power supplyis not sufficient or not stable, you
may encounterproblems during operating or can not
operate
at all. In this case, please restart the device,
or unplug the device and plug it again, and ensure that
its
power supplyis normal.
4. The system supports standard USB1.1 and USB2.0
devices, such as standard U-disks, MP3 players,
mobile hard disks, etc
..
5. For obtaining betteraudio and video quality, It is
suggested to use the external device which accords
with USB2.0 standard.
6. When playing the video with high compression ratio,
these phenomenons, such as picture standstill
and
menu long time response, are normal.
7. For some USB device with power supply, such as large
size hard disk, MP4, etc., Suggest using it with
power
to avoid electric power shortage.
8. The file may not be playednormallybecause its
parameters, such as the pixel
of picture, code rate of
audio and video file, sampling rate of audio file, exceed
the limit
of the system.

Technical Information
Supported File Format in Media Player
Video:
--Codoc(llloilPOI
Flo--
.....,... __
-- -
MPG
Mpeg1, Mpeg2 .dat .mpg.mpeg 1080P
@30fps 20Mbps Main Profile
MPEG
MPEG2-PS MPEG2 .vob 1080P @30fps 20Mbps MPEG2: MP@HL
Mpeg4 Simple Profile and Advanced Simple
20Mbps Profile @Level 5
H.264
1080P @30fps
Main Profile and High Profile@Level
MP4
.mp4
4.0
Motion JPEG
680X480 @ 30fps 10Mbps
MPEG2: MP@HL
Mpeg1,2,4 MPEG4: Simple Profile and
20Mbps Advanced
Simple Profile @Level 5
1 0B0P @ 30fps Main Profile and High Profile@Level
MKV
H.264
.mkv
4.0
Motion JPEG 680X480 @ 30fps 10Mbps
MPEG2: MP@HL
Mpeg2,4 MPEG4: Simple Profile and
1080P @30fps
20Mbps Advanced
Simple Profile @Level 5
AVI .avi Main Profile and High Profile@Level
H.264
4.0
Motion JPEG 680X480 @ 30fps 10Mbps
Audio:
-CodlclllloilPOI
,.. __
--
MPEG1 Layer2 32Kbps -448Kbps(Bit rate)
32KHz -4BKHz(Sampling rate)
.MP3
MPEG1 Layer3 32Kbps -320Kbps(Bit rate)
32KHz -48KHz(Sampling rate)
AAC, HEAAC .m4a.aac 24Kbps -384Kbps(Bit rate)
8KHz -48KHz(Sampling rate)
Bitrate: 64Kbps -1.5Mbps
LPCM Sampling Rate:
8KHz - 48Khz
IMA-ADPCM/MS-ADPCM Bitrate: 384Kbps
N/A
Sampling Rate: 8KHz - 48Khz
(work with video files only)
AC3 Bi1rate: 32Kbps -640Kbps
Sampling Rate: 32KHz,44.1Khz, 48Khz
EAC3 Bitrate: 32Kbps -
6Mbps
Sampling Rate: 32KHz,44.1Khz , 48Khz
18

Photo:
-
Flo--
--
Base-line
15360x8640
.jpeg
{1920X81080X8)
Progressive 1024x768
JPEG
15360x8640
.jpg
Base-line
(1920X8 1080X8)
Progressive 1024x768
non-interlace
9600x6400
PNG
.png
interlace 1200x800
BMP .bmp 9600x6400
( Note)
• Some files may not be played back even if they fulfil these conditions.
• The device may become unusable with this
TV ifthe file or folder names are changed.
19

Maintenance
First, remove the mains plug from the socket outlet.
Regular care:
Gently wipe the surface
of the display panel, cabinet, or
pedestal by using a soft cloth to clean the dirt or
fingerprints.
For stubborn dirt:
First clean the dust on the surface. Dampen a soft cloth
with clean water
or diluted neutral detergent ( 1 part
detergent to 100 parts water).
Wring the cloth and wipe the surface.
Finally, wipe away all the moisture.
Mains plug
Wipe the mains plug with a dry cloth at regular intervals.
Moisture and dust may lead to fire
or electrical shock.
A. ( Caution )
Do not use a hard cloth
or rub the surface too hard,
otherwise this may cause scratches on the surface.
• Take care not to subject the TV' surfaces to water
or
detergent Liquid inside the TV could lead to product
failure.
• Take care not to subject the surface to insect repellent,
solvent, thinner
or other volatile substances. This may
degrade surface quality
or cause peeling pf the paint.
• The surface
of the display panel is specially treated and
may be easily damaged. Take care not to tap
or scratch
the surface with your fingernail
or other hard objects.
• Do not allow the cabinet and pedestal to make contact
with a rubber
or PVC substance for a long time.
This may degrade surface quality.
20
Troubleshooting
Most problems you encounterwith your TV can be
corrected by consulting the following troubleshooting list.
No picture, no sound
• Check ifthe fuse
or circuit breaker is working.
• Plug another electrical device into the outlet to make
sure it
is working or turned on.
• Power plug
is in a bad contact with the outlet.
• Check the signal source.
No colour
• Adjust the saturation.
Remote control does not work
• Change the batteries.
• Batteries are not installed correctly.
• Main power
is not connected.
No picture, normal sound
• Adjust the brightness and contrast.
Normal picture, no sound
• Press the Vol+ button to increase volume.
• Volume is set to mute, press the mute button to restore
sound.
Radio frequency interference
This interference produces moving ripples
or diagonal
streaks, and
in some case, loss of contrast in the picture.
Find out and remove the radio interference source.