Panasonic TH-50PX60U User manual

©2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
TH-50PX60U
GP9DU Chassis
Digital High Definition Plasma Television
Specifications
Power Source AC 120 V, 50/60 Hz
Power Consumption
Maximum 515 W
Standby condition 0.2 W
Plasma Display panel
Drive method AC type
Aspect Ratio 16 : 9
Contrast Ratio 3000 : 1
Visible screen size
(No. of pixels) 127 cmV
43.6 ” × 24.5 ” × 50.0 ” (1,106 mm × 622 mm × 1,269 mm)
1,049,088 (1,366 (W) × 768 (H)) [4,098 × 768 dots]
Sound
Speaker 4.8 ” × 2.4 ” (120 mm × 60 mm) × 2 pcs, 8W
Audio Output 20 W [10 W + 10 W] (10 % THD)
Channel Capability (Digital/Analog) VHF/UHF: 2 - 69, CATV: 1 - 135
Operating Conditions Temperature: 32 °F - 104 °F (0 °C - 40 °C)
Humidity: 20 % - 80 % RH (non-condensing)
Connection Terminals
INPUT 1-3 VIDEO: RCA PIN Type × 1 1.0 V [p-p] (75 W)
S-VIDEO: Mini DIN 4-pin Y: 1.0 V [p-p] (75 W) C: 0.286 V [p-p] (75 W)
AUDIO L-R: RCA PIN Type × 2 0.5 V [rms]
COMPONENT VIDEO
INPUT 1-2 Y: 1.0 V [p-p] (including synchronization)
PB,P
R:± 0.35 V [p-p]
AUDIO L-R: RCA PIN Type × 2 0.5 V [rms]
HDMI 1-2 TYPE A Connector
AUDIO L-R: RCA PIN Type × 2 0.5 V [rms]
Card slot SD CARD slot × 1
AV PROG. OUT VIDEO: RCA PIN Type × 1 1.0 V [p-p] (75 W)
ORDERNO.MTNC060264CE
B19Canada: B07

1 Applicable signals 4
2 Safety Precautions 4
2.1. General Guidelines 4
3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 5
4 About lead free solder (PbF) 6
5 Service Hint 7
6 Plasma panel replacement method 8
6.1. Remove the Back cover 8
6.2. Remove the fan 8
6.3. Remove the rear terminal cover 8
6.4. Remove the P-Board 8
6.5. Remove the PA-Board 9
6.6. Remove the tuner unit 9
6.7. Remove the DT-Board 10
6.8. Remove the DG-Board 10
6.9. Remove the H-Board 11
6.10. Remove the HC-Board 11
6.11. Remove the D-Board 11
6.12. Remove the SU-Board 11
6.13. Remove the SD-Board 12
6.14. Remove the SC-Board 12
6.15. Remove the SS2-Board 12
6.16. Remove the SS3-Board 12
6.17. Remove the SS-Board 13
6.18. Remove the C1-Board 13
6.19. Remove the C2-Board 13
6.20. Remove the C3-Board 13
6.21. Remove the stand brackets 14
6.22. Remove the C4-Board 14
6.23. Remove the C5-Board 14
6.24. Remove the C6-Board 14
6.25. Remove the front bracket 15
6.26. Remove the G-Board, GK-Board and GS-Board 15
6.27. Remove the speaker L, R 15
6.28. Remove the S-Board 15
6.29. Remove the K-Board 16
6.30. Remove the Plasma panel section from the Front frame
(glass) 16
6.31. Replace the plasma panel (finished) 16
7 Location of Lead Wiring 17
7.1. Lead of Wiring (1) 17
7.2. Lead of Wiring (2) 18
7.3. Lead of Wiring (3) 19
7.4. Lead of Wiring (4) 20
7.5. Lead of Wiring (5) 21
7.6. Lead of Wiring (6) 22
8 Self-check Function 23
8.1. Check of the IIC bus lines 23
8.2. Power LED Blinking timing chart 25
8.3. No Power 26
8.4. No Picture 27
8.5. Local screen failure 28
9 Serviceman Mode 29
9.1. How to enter into Serviceman Mode 29
9.2. Contents of adjustment mode 29
9.3. Memory edit mode 30
9.4. Device data mode 31
10 Adjustment Procedure 32
10.1. Driver Set-up 32
10.2. Initialization Pulse Adjust 33
10.3. P.C.B. (Printed Circuit Board) exchange 33
AUDIO L-R: RCA PIN Type × 2 0.5 V [rms]
DIGITAL AUDIO OUT PCM/Dolby Digital, Fiber Optic
FEATURES 3D Y/C FILTER
CLOSED CAPTION V-Chip
Photo Viewer
Dimensions (W × H × D)
Including pedestal 47.7 ” × 34.8 ” × 14.6 ” (1,210 mm × 882 mm × 371 mm)
TV Set only 47.7 ” × 32.2 ” × 3.8 ” (1,210 mm × 818 mm × 95 mm)
Weight
Including pedestal 93.7 lb. (42.5 kg)
TV Set only 88.2 lb. (40 kg)
Note:
Design and Specifications are subject change without notice.
Weight and Dimensions shown are approximate.
CONTENTS
Page Page
2
TH-50PX60U

10.4. Adjustment Volume Location 34
10.5. Test Point Location 34
11 Adjustment 35
11.1. White balance adjustment 35
11.2. Sub bright adjustment 37
11.3. ABL operation level adjustment 38
12 Hotel mode 39
13 Conduct Views 41
13.1. P-Board 41
13.2. PA-Board 44
13.3. H-Board 46
13.4. G and GS-Board 48
13.5. GK, HC, K and S-Board 49
13.6. DG-Board 50
13.7. DT-Board 52
13.8. D-Board 54
13.9. C1-Board 56
13.10. C2-Board 57
13.11. C3-Board 58
13.12. C4-Board 59
13.13. C5-Board 60
13.14. C6-Board 61
13.15. SC-Board 62
13.16. SU-Board 65
13.17. SD-Board 66
13.18. SS-Board 67
13.19. SS-Board 69
14 Block and Schematic Diagram 71
14.1. Schematic Diagram Note 71
14.2. Main Block Diagram 72
14.3. P-Board Block Diagram 73
14.4. P-Board (1 of 2) Schematic Diagram 74
14.5. P-Board (2 of 2) Schematic Diagram 75
14.6. PA-Board Block Diagram 76
14.7. PA-Board (1 of 3) Schematic Diagram 77
14.8. PA-Board (2 of 3) Schematic Diagram 78
14.9. PA-Board (3 of 3) Schematic Diagram 79
14.10. H-Board Block Diagram 80
14.11. H-Board (1 of 3) Schematic Diagram 81
14.12. H-Board (2 of 3) Schematic Diagram 82
14.13. H-Board (3 of 3) Schematic Diagram 83
14.14. G, GK, HC, K and S-Board Block Diagram 84
14.15. G-Board Schematic Diagram 85
14.16. GK, K, HC and S-Board Schematic Diagram 86
14.17. DG-Board (1 of 3) Block Diagram 87
14.18. DG-Board (2 of 3) Block Diagram 88
14.19. DG-Board (3 of 3) Block Diagram 89
14.20. DG-Board (1 of 8) Schematic Diagram 90
14.21. DG-Board (2 of 8) Schematic Diagram 91
14.22. DG-Board (3 of 8) Schematic Diagram 92
14.23. DG-Board (4 of 8) Schematic Diagram 93
14.24. DG-Board (5 of 8) Schematic Diagram 94
14.25. DG-Board (6 of 8) Schematic Diagram 95
14.26. DG-Board (7 of 8) Schematic Diagram 96
14.27. DG-Board (8 of 8) Schematic Diagram 97
14.28. DT and GS-Board Block Diagram 98
14.29. DT-Board (1 of 6) Schematic Diagram 99
14.30. DT-Board (2 of 6) Schematic Diagram 100
14.31. DT-Board (3 of 6) Schematic Diagram 101
14.32. DT-Board (4 of 6) Schematic Diagram 102
14.33. DT-Board (5 of 6) Schematic Diagram 103
14.34. DT-Board (6 of 6) Schematic Diagram 104
14.35. D-Board (1 of 2) Block Diagram 105
14.36. D-Board (2 of 2) Block Diagram 106
14.37. D-Board (1 of 8) Schematic Diagram 107
14.38. D-Board (2 of 8) Schematic Diagram 108
14.39. D-Board (3 of 8) Schematic Diagram 109
14.40. D-Board (4 of 8) Schematic Diagram 110
14.41. D-Board (5 of 8) Schematic Diagram 111
14.42. D-Board (6 of 8) Schematic Diagram 112
14.43. D-Board (7 of 8) Schematic Diagram 113
14.44. D-Board (8 of 8) Schematic Diagram 114
14.45. C1, C2, C5 and C6-Block Diagram 115
14.46. C3, C4, SS, SS2 and SS3-Board Block Diagram 116
14.47. C1-Board (1 of 2) Schematic Diagram 117
14.48. C1-Board (2 of 2) Schematic Diagram 118
14.49. C2-Board (1 of 3) Schematic Diagram 119
14.50. C2-Board (2 of 3) Schematic Diagram 120
14.51. C2-Board (3 of 3) Schematic Diagram 121
14.52. C3-Board (1 of 2) Schematic Diagram 122
14.53. C3-Board (2 of 2) Schematic Diagram 123
14.54. C4-Board (1 of 2) Schematic Diagram 124
14.55. C4-Board (2 of 2) Schematic Diagram 125
14.56. C5-Board (1 of 3) Schematic Diagram 126
14.57. C5-Board (2 of 3) Schematic Diagram 127
14.58. C5-Board (3 of 3) Schematic Diagram 128
14.59. C6-Board (1 of 2) Schematic Diagram 129
14.60. C6-Board (2 of 2) Schematic Diagram 130
14.61. SS, SS2 and SS3-Board Schematic Diagram 131
14.62. SC, SU and SD-Board Block Diagram 132
14.63. SC-Board (1 of 2) Schematic Diagram 133
14.64. SC-Board (2 of 2) Schematic Diagram 134
14.65. SU-Board (1 of 2) Schematic Diagram 135
14.66. SU-Board (2 of 2) Schematic Diagram 136
14.67. SD-Board (1 of 2) Schematic Diagram 137
14.68. SD-Board (2 of 2) Schematic Diagram 138
15 Parts Location & Mechanical Replacement Parts List 139
15.1. Parts Location 139
15.2. Packing Exploded Views 140
15.3. Mechanical Replacement Parts List 141
16 Electrical Replacement Parts List 142
16.1. Replacement Parts List Notes 142
16.2. Electrical Replacement Parts List 143
3
TH-50PX60U

2.1.1. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two
prongs on the plug.
2. Measure the resistance value, with an ohmmeter, between
the jumpered AC plug and each exposed metallic cabinet
part on the equipment such as screwheads, connectors,
control shafts, etc. When the exposed metallic part has a
return path to the chassis, the reading should be between
1MWand 5.2MW.
When the exposed metal does not have a return path to
the chassis, the reading must be .
Figure 1
2.1.2. Leakage Current Hot Check (See
Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use an
isolation transformer for this check.
2. Connect a 1.5kW, 10 watts resistor, in parallel with a 0.15µF
capacitors, between each exposed metallic part on the set
and a good earth ground such as a water pipe, as shown in
Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more
sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of the
above measurements.
6. The potential at any point should not exceed 0.75 volts
RMS. A leakage current tester (Simpson Model 229 or
equivalent) may be used to make the hot checks, leakage
current must not exceed 1/2 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the
customer.
1 Applicable signals
2 Safety Precautions
2.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
4
TH-50PX60U

3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum
foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
5
TH-50PX60U

4 About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol stamped on the back of PCB.
Caution
· Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
· Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
· After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto
the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
6
TH-50PX60U

5 Service Hint
Board Name Function Board Name Function
PPower Supply C1 Data Driver (Upper Right)
PA DC-DC Converter
Speaker out, Audio AMP, Fan Control
C2 Data Driver (Upper Center)
C3 Data Driver (Upper Left)
HAV Terminal, AV Switch C4 Data Driver (Lower Left)
DG Digital Signal Processor, Micom, HDMI Interface C5 Data Driver (Lower Center)
DT ATSC Interface C6 Data Driver (Lower Right)
DFormat Converter, Plasma AI, Sub-Field Processor SC Scan Drive
GS SD Card Slot SU Scan out (Upper)
KRemote receiver, Power LED SD Scan out (Lower)
SPower Switch SS Sustain Drive
GFront Terminal SS2 Sustain Connector (Upper)
GK Key Switch SS3 Sustain Connector (Lower)
HC Jig Connection
7
TH-50PX60U

6.1. Remove the Back cover
1. See Service Hint (Section 5)
6.2. Remove the fan
1. Disconnect the relay couplers.
2. Remove the screws (×3 each) and remove the fans.
6.3. Remove the rear terminal
cover
1. Remove the screws (×8 ,×5 ,×2 ).
2. Remove the rear terminal cover.
6.4. Remove the P-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for
discharge from electrolysis capacitors.
1. Disconnect the couplers (P2, P5, P9, P10, P11, P12, P23
and P25).
2. Remove the screws (×6 ) and remove the P-Board unit.
3. Remove the screws (×9 ) on the back side.
6 Plasma panel replacement method
8
TH-50PX60U

4. Remove the screws (×5 ).
5. Remove the molding props (×8 ).
6. Remove the P-Board.
Note:
When assembling the P-Board, the position of each hole of
the insulation sheets (A and B) is set to the position of each
hole of the P-Board, then assemble them. ( marks
indicate setting positions.)
6.5. Remove the PA-Board
1. Unlock the cable clampers to free the cable.
2. Disconnect the couplers (PA2, PA5, PA10, PA31, PA32,
PA33, PA34 and PA40).
3. Disconnect the flexible cable (PA20).
4. Remove the screws (×4 ) and remove the earth cable.
5. Remove the PA-Board.
6.6. Remove the tuner unit
1. Unlock the cable clampers to free the cable.
2. Disconnect the couplers (DG5, G51, GS52, PA40 and earth
cable).
3. Disconnect the flexible cables (DG3 and PA20).
4. Remove the screws (×4 ) remove the tuner unit.
9
TH-50PX60U

6.7. Remove the DT-Board
1. Unlock the cable clampers to free the cable.
2. Disconnect the couplers (HC06 and DT10).
3. Remove the screws (×5 ) remove the DT-Board unit.
(Be careful the coupler (DT12-DG22) when remove the DT-
Board unit.)
4. Disconnect the coupler (DT07).
5. Remove the screws (×2 ).
6. Remove the DT-Board metal cover and DT-Board.
6.8. Remove the DG-Board
1. Remove the DT-Board. (See section 6.7.)
2. Remove the screws (×8 ) and remove the DT-Board
metal frame.
3. Disconnect the coupler (DG2).
4. Disconnect the flexible cables (DG1, DG15 and DG20).
5. Remove the screw (×1 ) remove the DG-Board.
10
TH-50PX60U

6.9. Remove the H-Board
1. Unlock the cable clampers to free the cable.
2. Disconnect the couplers (H2, H40 and H51).
3. Disconnect the flexible cable (H1).
4. Remove the screws (×6 ) and remove the H-Board.
6.10. Remove the HC-Board
1. Disconnect the couple (HC06).
2. Disconnect the flexible cable (HC15).
3. Remove the screws (×2 ) and remove the HC-Board.
6.11. Remove the D-Board
1. Remove the tuner unit. (See section 6.6.)
2. Disconnect the couplers (D5, D20 and D25).
3. Disconnect the flexible cables (D3, D31, D32, D33 and
D34).
4. Remove the screws (×4 ) and remove the D-Board.
6.12. Remove the SU-Board
1. Remove the screws (×3 ).
2. Remove the flexible cables (SU1, SU2, SU3 and SU4) and
remove the bridge connector (SU45).
3. Slide the SU-Board to the left to disconnect from a coupler
(SC41-SU41) on the SC-Board and remove the SU-Board.
11
TH-50PX60U

6.13. Remove the SD-Board
1. Remove the screws (×3 ).
2. Remove the flexible cables (SD1, SD2, SD3 and SD4) and
remove the bridge connector (SD46).
3. Slide the SD-Board to the left to disconnect from a coupler
(SC42-SD42) on the SC-Board and remove the SD-Board.
6.14. Remove the SC-Board
1. Unlock the cable clampers to free the cable.
2. Disconnect the couplers (SC2, SC20 and SC23).
3. Remove the screws (×9 ) and remove the SC-Board.
6.15. Remove the SS2-Board
1. Disconnect the coupler (SS23) and disconnect the flexible
cable (SS55).
2. Remove the screws (×2 ) and remove the SS2-Board.
6.16. Remove the SS3-Board
1. Disconnect the coupler (SS22) and disconnect the flexible
cable (SS56).
2. Remove the screws (×2 ) and remove the SS3-Board.
12
TH-50PX60U

6.17. Remove the SS-Board
1. Remove the SS2-Board and SS3-Board. (See section 6.15.
and 6.16)
2. Disconnect the couplers (SS11, SS12, SS33, SS43 and
SS44).
3. Disconnect the flexible cables (SS51, SS52, SS53 and
SS54).
4. Remove the screws (×7 ) and remove the SS-Board.
6.18. Remove the C1-Board
1. Remove the flexible cables holder fastening screws (×6
).
2. Disconnect the flexible cables (CA1, CA2 and CA3).
3. Disconnect the flexible cable (C10).
4. Remove the screws (×5 ) and remove the C1-Board.
6.19. Remove the C2-Board
1. Remove the flexible cables holder fastening screws (×8
).
2. Disconnect the flexible cables (CA4, CA5, CA6 and CA7).
3. Disconnect the flexible cables (C20, C21 and C22).
4. Remove the screws (×5 ) and remove the C2-Board.
6.20. Remove the C3-Board
1. Remove the flexible cables holder fastening screws (×8
).
2. Disconnect the flexible cables (CA8, CA9, CA10 and
CA11).
3. Disconnect the flexible cables (C31 and C32).
4. Disconnect the coupler (C33).
5. Remove the screws (×5 ) and remove the C3-Board.
13
TH-50PX60U

6.21. Remove the stand brackets
1. Remove the plasma panel section from the servicing stand
and lay on a fiat surface such as a table (covered) with the
plasma panel surface facing downward.
2. Remove the stand brackets (left, right) fastening screws (×6
each) and remove the stand brackets (left, right).
6.22. Remove the C4-Board
1. Remove the stand bracket (left). (See section 6.21.)
2. Remove the flexible cables holder fastening screws (×8
).
3. Disconnect the flexible cables (CB8, CB9, CB10 and
CB11).
4. Disconnect the flexible cables (C41 and C42).
5. Disconnect the couplers (C43 and C44).
6. Remove the screws (×5 ) and remove the C4-Board.
6.23. Remove the C5-Board
1. Remove the flexible cables holder fastening screws (×8
).
2. Disconnect the flexible cables (CB4, CB5, CB6 and CB7).
3. Disconnect the flexible cables (C50, C51 and C52).
4. Remove the screws (×5 ) and remove the C5-Board.
6.24. Remove the C6-Board
1. Remove the stand bracket (right). (See section 6.21.)
2. Remove the flexible cables holder fastening screws (×6
).
3. Disconnect the flexible cables (CB1, CB2 and CB3).
4. Disconnect the flexible cable (C60).
5. Remove the screws (×5 ) and remove the C6-Board.
14
TH-50PX60U

6.25. Remove the front bracket
1. Unlock the cable clampers to free the cable.
2. Disconnect the couplers (GS52, G1 and G51).
3. Remove the screws (×5 ) and remove the front bracket.
6.26. Remove the G-Board, GK-
Board and GS-Board
1. Remove the front bracket. (See section 6.25.)
2. Remove the screws (×3 ) and remove the metal cover.
3. Remove the screws (×3 ) from front side and remove the
front side metal frame.
4. Remove the screws (×5 ) and disconnect the couplers
(G3-GK3).
5. Remove the G-Board, GK-Board and GS-Board.
6.27. Remove the speaker L, R
1. Remove the screws (×2 each) and remove the speaker
L, R.
6.28. Remove the S-Board
1. Disconnect the coupler (S1).
2. Remove the screws (×2 ) and remove the S-Board metal
frame.
3. Remove the screws (×2 ) and remove the S-Board.
15
TH-50PX60U

6.29. Remove the K-Board
1. Unlock the cable clampers to free the cable.
2. Disconnect the couplers (G1 and S1). (See section 6.25.
and 6.28.)
3. Remove the screws (×2 ) and remove the K-Board.
6.30. Remove the Plasma panel
section from the Front frame
(glass)
1. Remove the front frame and the plasma panel fastening
screws (×6 ).
2. Remove the front frame and the stand brackets fastening
screws (×4 ).
3. For leaving the plasma panel from the front frame, pull the
bottom of the front frame forward, lift, and remove.
6.31. Replace the plasma panel
(finished)
1. Place the new plasma panel (finished) on the flat surface of
the table (covered by a soft cloth), with the plasma panel
surface facing downward.
2. Attach the C1, C2, C3, C4, C5 and the C6-Board, connect
the flexible cables (×22) from the Plasma panel to the C1,
C2, C3, C4, C5 and the C6-Board, and fit the flexible cable
holders.
3. Attach the Hooks (left, right) and fit the stand brackets (L,
R) to the new plasma panel.
4. Place the plasma panel section on the servicing stand.
5. Attach the front frame and each P.C.Board and so on, to
the new plasma panel.
* When fitting the front frame, be careful to allow any
debris, dust or handling residue to remain between the
front glass and plasma panel.
16
TH-50PX60U

7 Location of Lead Wiring
7.1. Lead of Wiring (1)
17
TH-50PX60U

7.2. Lead of Wiring (2)
18
TH-50PX60U

7.3. Lead of Wiring (3)
19
TH-50PX60U

7.4. Lead of Wiring (4)
20
TH-50PX60U