Panasonic TX-P50S20B User manual

© Panasonic Corporation 2010.
Unauthorized copying and distribution is a violation
of law.
ORDER NO.PCZ1003023CE
Plasma Television
Model No. TX-P50S20B
GPF13DE Chassis

2
TABLE OF CONTENTS PAGE PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Touch-Current Check--------------------------------------3
2Warning--------------------------------------------------------------4
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------4
2.2. About lead free solder (PbF) ----------------------------5
3 Service Navigation------------------------------------------------6
3.1. PCB Layout--------------------------------------------------6
3.2. Applicable signals------------------------------------------7
4 Specifications ------------------------------------------------------8
5 Technical Descriptions------------------------------------------9
5.1. Specification of KEY for CI Plus, DTCP-IP and
One-to-One--------------------------------------------------9
6 Service Mode-----------------------------------------------------10
6.1. How to enter into Service Mode----------------------10
6.2. Option - Mirror---------------------------------------------12
6.3. Service tool mode----------------------------------------12
6.4. Hotel mode-------------------------------------------------13
6.5. Data Copy by SD Card ---------------------------------14
7 Troubleshooting Guide----------------------------------------17
7.1. Check of the IIC bus lines------------------------------17
7.2. Power LED Blinking timing chart---------------------18
7.3. No Power---------------------------------------------------19
7.4. No Picture--------------------------------------------------20
7.5. Local screen failure--------------------------------------21
8 Service Fixture & Tools ---------------------------------------22
8.1. SC jig--------------------------------------------------------22
9 Disassembly and Assembly Instructions---------------23
9.1. Remove the Rear cover --------------------------------23
9.2. Remove the AC inlet ------------------------------------23
9.3. Remove the P-Board------------------------------------23
9.4. Remove the Side terminal cover and the Side
shield metal------------------------------------------------23
9.5. Remove the Tuner unit ---------------------------------23
9.6. Remove the A-Board------------------------------------24
9.7. Remove the XW-Board---------------------------------24
9.8. Remove the Speakers ----------------------------------25
9.9. Remove the SU-Board----------------------------------25
9.10. Remove the SD-Board----------------------------------25
9.11. Remove the SC-Board----------------------------------25
9.12. Remove the SS2-Board --------------------------------26
9.13. Remove the SS-Board----------------------------------26
9.14. Remove the Hanger metals and the Stand
brackets-----------------------------------------------------26
9.15. Remove the C1-Board----------------------------------27
9.16. Remove the C2-Board----------------------------------27
9.17. Remove the C3-Board----------------------------------27
9.18. Remove the Plasma panel section from the
Cabinet assy (glass)-------------------------------------27
9.19. Remove the Glass holders ----------------------------28
9.20. Remove the K-Board------------------------------------28
9.21. Replace the plasma panel -----------------------------28
10 Measurements and Adjustments --------------------------29
10.1. Adjustment-------------------------------------------------29
11 Block Diagram ---------------------------------------------------33
11.1. Main Block Diagram-------------------------------------33
11.2. Block (1/5) Diagram -------------------------------------34
11.3. Block (2/5) Diagram -------------------------------------35
11.4. Block (3/5) Diagram -------------------------------------36
11.5. Block (4/5) Diagram -------------------------------------37
11.6. Block (5/5) Diagram -------------------------------------38
12 Wiring Connection Diagram---------------------------------39
12.1. Caution statement.---------------------------------------39
12.2. Wiring (1) -------------------------------------------------- 39
12.3. Wiring (2) -------------------------------------------------- 40
12.4. Wiring (3) -------------------------------------------------- 41
13 Schematic Diagram -------------------------------------------- 43
13.1. Schematic Diagram Note------------------------------ 43
13.2. P-Board (1/3) Schematic Diagram ------------------ 44
13.3. P-Board (2/3) Schematic Diagram ------------------ 45
13.4. P-Board (3/3) Schematic Diagram ------------------ 46
13.5. A-Board (1/22) Schematic Diagram----------------- 47
13.6. A-Board (2/22) Schematic Diagram----------------- 48
13.7. A-Board (3/22) Schematic Diagram----------------- 49
13.8. A-Board (4/22) Schematic Diagram----------------- 50
13.9. A-Board (5/22) Schematic Diagram----------------- 51
13.10. A-Board (6/22) Schematic Diagram----------------- 52
13.11. A-Board (7/22) Schematic Diagram----------------- 53
13.12. A-Board (8/22) Schematic Diagram----------------- 54
13.13. A-Board (9/22) Schematic Diagram----------------- 55
13.14. A-Board (10/22) Schematic Diagram--------------- 56
13.15. A-Board (11/22) Schematic Diagram --------------- 57
13.16. A-Board (12/22) Schematic Diagram--------------- 58
13.17. A-Board (13/22) Schematic Diagram--------------- 59
13.18. A-Board (14/22) Schematic Diagram--------------- 60
13.19. A-Board (15/22) Schematic Diagram--------------- 61
13.20. A-Board (16/22) Schematic Diagram--------------- 62
13.21. A-Board (17/22) Schematic Diagram--------------- 63
13.22. A-Board (18/22) and K-Board Schematic
Diagram---------------------------------------------------- 64
13.23. A-Board (19/22) Schematic Diagram--------------- 65
13.24. A-Board (20/22) Schematic Diagram--------------- 66
13.25. A-Board (21/22) Schematic Diagram--------------- 67
13.26. A-Board (22/22) Schematic Diagram--------------- 68
13.27. XW-Board Schematic Diagram----------------------- 69
13.28. C1-Board Schematic Diagram ----------------------- 70
13.29. C2-Board (1/2) Schematic Diagram ---------------- 71
13.30. C2-Board (2/2) Schematic Diagram ---------------- 72
13.31. C3-Board (1/2) Schematic Diagram ---------------- 73
13.32. C3-Board (2/2) Schematic Diagram ---------------- 74
13.33. SC-Board (1/4) Schematic Diagram ---------------- 75
13.34. SC-Board (2/4) Schematic Diagram ---------------- 76
13.35. SC-Board (3/4) Schematic Diagram ---------------- 77
13.36. SC-Board (4/4) Schematic Diagram ---------------- 78
13.37. SS-Board (1/2) Schematic Diagram ---------------- 79
13.38. SS-Board (2/2) and SS2-Board Schematic
Diagram---------------------------------------------------- 80
14 Printed Circuit Board------------------------------------------ 81
14.1. P-Board ---------------------------------------------------- 81
14.2. K and SS2-Board---------------------------------------- 84
14.3. A-Board ---------------------------------------------------- 85
14.4. XW-Board-------------------------------------------------- 87
14.5. C1-Board--------------------------------------------------- 88
14.6. C2-Board--------------------------------------------------- 89
14.7. C3-Board--------------------------------------------------- 90
14.8. SC-Board -------------------------------------------------- 91
14.9. SS-Board -------------------------------------------------- 93
15 Exploded View and Replacement Parts List----------- 95
15.1. Exploded View and Mechanical Replacement
Parts List--------------------------------------------------- 95
15.2. Electrical Replacement Parts List ------------------102

3
1 Safety Precautions
1.1. General Guidelines
1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.2. Touch-Current Check
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground
such as a water pipe, as shown in Figure 1.
3. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reserve the AC plug in the AC outlet and repeat each of the above measure.
6. The potential at any point (TOUGH CURRENT) expressed as voltage U1and U2, does not exceed the following values:
For a. c.: U1= 35 V (peak) and U2= 0.35 V (peak);
For d. c.: U1= 1.0 V,
Note:
The limit value of U2= 0.35 V (peak) for a. c. and U1= 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0
mA d. c.
The limit value U1= 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.
7. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the customer.
Figure 1

4
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-
ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient
to damage an ES device).

5
2.2. About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please
use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-
der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the
opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-
ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

6
3 Service Navigation
3.1. PCB Layout
Board Name Function Board Name Function
P Power Supply C1 Data Driver (Lower Right)
C2 Data Driver (Lower Center)
A DC-DC Converter, Tuner
Speaker out, AV Terminal, HDMI in, SD Card
Digital Signal Processor, PEAKS-LDA2
Format Converter, Plasma AI, Sub-Field Processor
Power Switch, Key Switch
C3 Data Driver (Lower Left)
SC Scan Drive
SS Sustain Drive
SS2 Sustain out (Lower)
SU Scan out (Upper)
Non serviceable.
SU-Board should be exchanged for service.
SD Scan out (Lower)
Non serviceable.
SD-Board should be exchanged for service.
K Remote receiver, Power LED, C.A.T.S sensor
XW DVB Tuner

7
3.2. Applicable signals
COMPONENT (Y, PB, PR), HDMI
* Mark: Applicable input signal for Component (Y, PB, PR) and HDMI
PC (from HDMI terminal)
Applicable input signal for PC is basically compatible to HDMI standard timing.
Note
• Signals other than above may not be displayed properly.
• The above signals are reformatted for optimal viewing on your display.
• PC signal is magnified or compressed for display, so that it may not be possible to show fine detail with sufficient clarity.
Signal name COMPONENT HDMI
525 (480) / 60i * *
525 (480) / 60p * *
625 (576) / 50i * *
625 (576) / 50p * *
750 (720) / 60p * *
750 (720) / 50p * *
1,125 (1,080) / 60i * *
1,125 (1,080) / 50i * *
1,125 (1,080) / 60p *
1,125 (1,080) / 50p *
1,125 (1,080) / 24p *
Signal name Horizontal frequency (kHz) Vertical frequency (Hz)
640 ×480 @60 Hz 31.47 60.00
750 (720) / 60p 45.00 60.00
1,125 (1,080) / 60p 67.50 60.00

8
4 Specifications
Power Source AC 220-240 V, 50 / 60 Hz
Power Consumption 320 W
Power Consumption in Standby mode 0.4 W (Without monitor out recording)
16 W (With monitor out recording)
Display panel
Aspect Ratio 16:9
Visible screen size 127 cm (diagonal)
1,105 mm (W) ×622 mm (H)
Number of pixels 2,073,600 (1,920 (W) ×1,080 (H)) [5,760 ×1,080 dots]
Sound Speaker 160 mm ×40 mm ×2 pcs, 6 Ω
Audio Output 20 W ( 10 W + 10 W )
Headphones M3 (3.5 mm) stereo mini Jack ×1
Receiving Systems / Band name DVB-T/T2 : Digital terrestrial services via UHF aerial input.
PAL I : UHF E21-68
PAL 525/60 : Playback of NTSC tape from some PAL Video recorders (VCR)
or NTSC disc playback from DVD player and recorder.
M.NTSC : Playback from M.NTSC Video recorders (VCR).
NTSC (AV input only) : Playback from NTSC Video recorders (VCR).
Aerial - input UHF
Operating Conditions Temperature: 0 °C - 35 °C
Humidity: 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)
AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
AV3 VIDEO RCA PIN Type ×1 1.0 V [p-p] (75 Ω)
AUDIO L - R RCA PIN Type ×2 0.5 V [rms]
COMPONENT
VIDEO Y 1.0 V [p-p] (including synchronization)
PB, PR± 0.35 V [p-p]
AUDIO L - R RCA PIN Type ×2 0.5 V [rms]
Others
HDMI1 / 2 / 3 TYPE A Connectors
HDMI1 / 3 : HDMI (Version 1.4 with Content Type) and
HDMI (Version 1.3a with Deep Colour, x.v.Colour™)
HDMI2 : HDMI (Version 1.4 with Content Type, Audio Return Channel)
and HDMI (Version 1.3a with Deep Colour, x.v.Colour™)
• This TV supports [ HDAVI Control 5 ] function.
Card slot SD Card slot ×1
Common Interface slot ×1
ETHERNET RJ45, IEEE802.3 10BASE-T / 100BASE-TX
Output
AUDIO L - R RCA PIN Type ×2 0.5 V [rms] (high impedance)
DIGITAL AUDIO OUT PCM / Dolby Digital / DTS, Fiber optic
Dimensions (W ×H ×D) 1,218 mm ×814 mm ×401 mm (With Pedestal)
1,218 mm ×769 mm ×93 mm (TV only)
Mass 31.0 kg Net (With Pedestal)
29.0 kg Net (TV only)
Note
• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3.

9
5 Technical Descriptions
5.1. Specification of KEY for CI Plus, DTCP-IP and One-to-One
5.1.1. General information:
1. EEPROM (IC8950) for spare parts has the seed of KEY for each.
2. The final KEY data will be generated by Peaks IC (IC8000) when SELF CHECK was done and are stored in both Peaks IC
(IC8000) and EEPROM (IC8950).
Three KEY are not generated for all models.
The necessary KEY are only generated and stored depend on the feature of models.
5.1.2. Replacement of ICs:
When Peaks IC (IC8000) is replaced, EEPROM (IC8950) should be also replaced with new one the same time.
When EEPROM (IC8950) is replaced, Peaks IC (IC8000) is not necessary to be replaced the same time.
After the replacement of IC, SELF CHECK should be done to generate the final KEY data.
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more
than 3 seconds.
TV will be forced to the factory shipment setting after this SELF CHECK.
5.1.3. Model and Keys:
Model No. Keys
CI Plus DTCP-IP One-to-One
(For USB Rec.)
TX-P50S20B None None None

10
6 Service Mode
6.1. How to enter into Service Mode
While pressing [VOLUME ( - )] button of the main unit, press [0] button of the remote control three times within 2 seconds.
6.1.1. Key command
[1] button...Main items Selection in forward direction
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[RED] button...All Sub items Selection in forward direction
[GREEN] button...All Sub items Selection in reverse direction
[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )

11
6.1.2. Contents of adjustment mode
• Value is shown as a hexadecimal number.
• Preset value differs depending on models.
• After entering the adjustment mode, take note of the value in each item before starting adjustment.
6.1.3. How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.

12
6.2. Option - Mirror
Picture can be reversed left and right or up and down.
00 : Default (Normal picture is displayed)
01 : Picture is reversed left and right.
02 : Picture is reversed up and down.
Hint : If the defective symptom (e.g. Vertical bar or Horizontal bar) is moved by selection of this mirror, the possible cause is in
A-board.
6.3. Service tool mode
6.3.1. How to access
1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.
6.3.2. Display of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication will be cleared by [Self-check indication and forced to factory shipment setting].
6.3.3. POWER ON Time, On/Off
Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3sec.
Time : Cumulative power on time, indicated hour : minute by decimal
On/Off : Number of On/Off switching by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
6.3.4. Exit
1. Disconnect the AC cord from wall outlet or switch off the power with [ Power ] button on the main unit.

13
6.4. Hotel mode
1. Purpose
Restrict a function for hotels.
2. Access command to the Hotel mode setup menu
In order to display the Hotel mode setup menu, please
enter the following command (within 2 second).
[TV] : Vol. [Down] + [REMOTE] : AV (3 times)
Then, the Hotel mode setup menu is displayed.
3. To exit the Hotel mode setup menu
Disconnect AC power cord from wall outlet.
4. Explain the Hotel mode setup menu
item Function
Hotel Mode Select hotel mode ON/OFF
Initial INPUT Select input signal modes.
Set the input, when each time power is switched
on.
Selection :
Off/Analog/DVB/AV1/AV2/AV2S/AV3/COMPO-
NENT/HDMI1/HDMI2/HDMI3
• Off: give priority to a last memory. However,
Euro model is compulsorily set to TV.
• AVnS/AVnC: only Euro model selectable
• PC: selectable with VGA option
Initial POS Select programme number.
Selection :
Off/0 to 99
• Off: give priority to a last memory
Initial VOL level Adjust the volume when each time power is
switched on.
Selection/Range :
Off/0 to 100
• Off: give priority to a last memory
Maximum VOL
level Adjust maximum volume. Range :
0 to 100
Button lock Select local key conditions.
Selection :
Off/SETUP/MENU/ALL
• Off: altogether valid
• SETUP: only F-key is invalid
(Tuning guide (menu) can not be selected.)
• MENU: only F-key is invalid
(only Volume/Mute can be selected.)
• ALL: altogether invalid.
Remote lock Select remote control key conditions.
Selection :
Off/SETUP/MENU
• Off: altogether valid
• SETUP: only Setup menu is invalid
• MENU: Picture/Sound/Setup menu are invalid

14
6.5. Data Copy by SD Card
6.5.1. Purpose
(a) Board replacement (Copy the data when exchanging A-board):
When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board.
(b) Hotel (Copy the data when installing a number of units in hotel or any facility):
When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and then copy to other
TVs.
6.5.2. Preparation
Make pwd file as startup file for (a) or (b) in a empty SD card.
1. Insert a empty SD card to your PC.
2. Right-click a blank area in a SD card window, point to New, and then click text document. A new file is created by default
(New Text Document.txt).
3. Right-click the new text document that you just created and select rename, and then change the name and extension of the
file to the following file name for (a) or (b) and press ENTER.
File name:
(a) For Board replacement : boardreplace.pwd
(b) For Hotel : hotel.pwd
Note:
Please make only one file to prevent the operation error.
No any other file should not be in SD card.

15
6.5.3. Data copy from TV set to SD Card
1. Turn on the TV set.
2. Insert SD card with a startup file (pwd file) to SD slot.
On-screen Display will be appeared according to the startup file automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement : 2770
(b) For Hotel : 4850
Data will be copied from TV set to SD card.
It takes around 2 to 6 minutes maximum for copying.
4. After the completion of copying to SD card, remove SD card from TV set.
5. Turn off the TV set.
Note:
Following new folder will be created in SD card for data from TV set.
(a) For Board replacement : user_setup
(b) For Hotel : hotel

16
6.5.4. Data copy from to SD Card to TV set
1. Turn on the TV set.
2. Insert SD card with Data to SD slot.
On-screen Display will be appeared according to the Data folder automatically.
3. Input a following password for (a) or (b) by using remote control.
(a) For Board replacement : 2771
(b) For Hotel : 4851
Data will be copied from SD card to TV set.
4. After the completion of copying to SD card, remove SD card from TV set.
(a) For Board replacement : Data will be deleted after copying (Limited one copy).
(b) For Hotel : Data will not be deleted and can be used for other TVs.
5. Turn off the TV set.
Note:
1. Depending on the failure of boards, function of Data copy for board replacement does not work.
2. This function can be effective among the same model numbers.

17
7 Troubleshooting Guide
Use the self-check function to test the unit.
1. Checking the IIC bus lines
2. Power LED Blinking timing
7.1. Check of the IIC bus lines
7.1.1. How to access
7.1.1.1. Self-check indication only:
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control
for more than 3 seconds.
7.1.1.2. Self-check indication and forced to factory shipment setting:
Caution:
New key will be generated and previous TV programmes recorded in USB HDD will not be viewed. (See Chap.5)
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote con-
trol for more than 3 seconds.
7.1.2. Screen display
7.1.3. Check Point
Confirm the following parts if NG was displayed.
7.1.4. Exit
Disconnect the AC cord from wall outlet or switch off the power with [ Power ] button on the main unit.

18
7.2. Power LED Blinking timing chart
1. Subject
Information of LED Flashing timing chart.
2. Contents
When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the
defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.

19
7.3. No Power
First check point
There are following 2 states of No Power indication by power LED.
1. No lit
2. Red is lit then turns red blinking a few seconds later. (See 6.2.)

20
7.4. No Picture