Panasonic Viera TH-37PA60E User manual

©2006 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
TH-37PA60E
TH-37PD60B
TH-42PA60E
TH-42PD60B
GP9DE Chassis
Plasma Television
Specifications
Power Source
A
C 220-240 V, 50 / 60 Hz
Power Consumption
Average use 206 W (TH-37PA60E), 215 W (TH-37PD60B)
238 W (TH-42PA60E), 247 W (TH-42PD60B)
Standby condition 0.3 W (PA60E)
0.3 W (PD60B Without DVB recording), 20 W (PD60B With DVB recording)
Plasma Display panel
Drive method
A
Ctype
Aspect Ratio 16:9
Contrast Ratio Max 10000:1
Visible screen size
(No. of pixels) 94 cmV (37-inch), 106 cmV (42-inch)
818 mm (W) × 461 mm (H) × 939 mm (diagonal) (37-inch)
920 mm (W) × 518 mm (H) × 1,056 mm (diagonal) (42-inch)
408,960 (852 (W) × 480 (H)) [2,556 × 480 dots]
Sound
Speaker 12 cm × 6 cm × 2 pcs, 8 W
Audio Output 20 W (10 W + 10 W ), 10% THD
Receiving Systems /
Band name (PA60E) PAL B, G, H, I, SECAM B, G, SECAM L / L’
VHF E2 - E12
V
HF H1 - H2 (ITALY)
VHF A - H (ITALY) UHF E21 - E69
CATV (S01 - S05) CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2
V
HF R3 - R5
VHF R6 - R12 UHF E21 - E69
PAL 525/60
ORDER NO. PCZ0603011CE

1 Applicable signals 5 2 Safety Precautions 6
Playback of NTSC tape from some PAL Video recorders (VCR)
M.NTSC
Playback from M. NTSC Video recorders (VCR)
NTSC (AV input only)
Playback from NTSC Video recorders (VCR)
Receiving Systems /
Band name (PD60B) PAL I
UHF E21 - 68.
PAL 525/60
Playback of NTSC tape from some PAL Video recorders (VCR) or NTSC disc playback from DVD
player and recorder.
DVB
Digital terrestrial services via UHF aerial input.
M.NTSC
Playback from M.NTSC Video recorders (VCR).
NTSC (AV input only)
Playback from NTSC Video recorders (VCR).
Aerial - Rear VHF / UHF (PA60E)
UHF (PD60B)
Operating Conditions Temperature : 0°C-40°C
Humidity : 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Scart terminal) 21 Pin terminal (Audio / Video in, Audio / Video out, RGB in)
AV2 (Scart terminal) 21 Pin terminal (Audio / Video in, Audio / Video out, S-Video in, Q-Link)
AV3 (Scart terminal) 21 Pin terminal (Audio / Video in, Audio / Video out, RGB in, S-Video in, Q-Link)
Others COMPONENT Y
PB,P
R
1.0 V[p-p] (including synchronization)
±0.35 V[p-p]
HDMI TYPE A Connectors
AUDIO L - R RCA PIN Type × 2 0.5 V[rms]
Output AUDIO L - R RCA PIN Type × 2 0.5 V[rms] (high impedance)
Dimensions ( W × H × D )
968 mm × 641 mm × 97 mm (TV Set only) (37-inch)
968 mm × 704 mm × 320 mm (With Pedestal) (TH-37PA60E)
1,068 mm × 701 mm × 97 mm (TV Set only) (42-inch)
1,068 mm × 764 mm × 320 mm (With Pedestal) (TH-42PA60E)
Weight
25.0 kg Net (TV Set only) (37-inch)
27.0 kg Net (With Pedestal) (TH-37PA60E)
29.0 kg Net (TV Set only) (42-inch)
31.0 kg Net (With Pedestal) (TH-42PA60E)
Notes:
· Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.
· This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020.
CONTENTS
Page Page
2
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

2.1. General Guidelines 6
2.2. Touch-Current Check 6
3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 7
4 About lead free solder (PbF) 8
5 Service Hint 9
6 Plasma panel replacement method 10
6.1. Remove the Back cover 10
6.2. Remove the tuner cover 10
6.3. Remove the P-Board 10
6.4. Remove the PA-Board 10
6.5. Remove the tuner unit 11
6.6. Remove the XV-Board (PD60B) 11
6.7. Remove the DG-Board 11
6.8. Remove the TA-Board 12
6.9. Remove the H-Board 12
6.10. Remove the HC-Board 12
6.11. Remove the D-Board 12
6.12. Remove the SU-Board 13
6.13. Remove the SD-Board 13
6.14. Remove the SC-Board 14
6.15. Remove the SS-Board 14
6.16. Remove the C1-Board 14
6.17. Remove the C2-Board 15
6.18. Remove the speaker L, R 15
6.19. Remove the S-Board 16
6.20. Remove the K-Board 16
6.21. Remove the stand brackets 16
6.22. Remove the Plasma panel section from the Front frame
(glass) 17
6.23. Replace the plasma panel (finished) 17
7 Location of Lead Wiring 18
7.1. Lead of Wiring (1) 18
7.2. Lead of Wiring (2) 19
7.3. Lead of Wiring (3) 20
7.4. Lead of Wiring (4) 21
7.5. Lead of Wiring (5) 22
7.6. Lead of Wiring (6) 23
8 Self Check 24
8.1. Power LED Blinking timing chart 25
8.2. No Power 26
8.3. No Picture 27
8.4. Local screen failure 28
9 Service Mode Function 29
9.1. How to enter SERVICE 1 29
9.2. How to enter SERVICE 2 29
9.3. Option Description 31
10 Adjustment Procedure 33
10.1. Driver Set-up 33
10.2. Initialization Pulse Adjust 34
10.3. P.C.B. (Printed Circuit Board) exchange 34
10.4. Adjustment Volume Location 35
10.5. Test Point Location 35
11 Adjustment 36
11.1. PAL panel white balance adjustment 36
11.2. HD white balance adjustment 37
11.3. Sub bright adjustment 38
11.4. ABL adjustment 39
11.5. Sub-Contrast adjustment 40
12 Hotel mode 41
13 Conduct Views 43
13.1. P-Board (37inch) 43
13.2. P-Board (42inch) 46
13.3. PA-Board 49
13.4. H-Board 51
13.5. TA-Board 53
13.6. HC, K and S-Board 54
13.7. DG-Board 55
13.8. XV-Board (PD60B) 57
13.9. D-Board 59
13.10. C1-Board (37inch) 61
13.11. C1-Board (42inch) 62
13.12. C2-Board (37inch) 63
13.13. C2-Board (42inch) 64
13.14. SC-Board 65
13.15. SU-Board (37inch) 68
13.16. SU-Board (42inch) 69
13.17. SD-Board (37inch) 70
13.18. SD-Board (42inch) 71
13.19. SS-Board 72
14 Schematic and Block Diagram 75
14.1. Schematic Diagram Note 75
14.2. Main Block Diagram 76
14.3. P-Board Block Diagram (37inch) 77
14.4. P-Board (1 of 6) Schematic Diagram (37inch) 78
14.5. P-Board (2 of 6) Schematic Diagram (37inch) 79
14.6. P-Board (3 of 6) Schematic Diagram (37inch) 80
14.7. P-Board (4 of 6) Schematic Diagram (37inch) 81
14.8. P-Board (5 of 6) Schematic Diagram (37inch) 82
14.9. P-Board (6 of 6) Schematic Diagram (37inch) 83
14.10. P-Board Block Diagram (42inch) 84
14.11. P-Board (1 of 6) Schematic Diagram (42inch) 85
14.12. P-Board (2 of 6) Schematic Diagram (42inch) 86
14.13. P-Board (3 of 6) Schematic Diagram (42inch) 87
14.14. P-Board (4 of 6) Schematic Diagram (42inch) 88
14.15. P-Board (5 of 6) Schematic Diagram (42inch) 89
14.16. P-Board (6 of 6) Schematic Diagram (42inch) 90
14.17. PA-Board Block Diagram 91
14.18. PA-Board (1 of 2) Schematic Diagram 92
14.19. PA-Board (2 of 2) Schematic Diagram 93
14.20. H and TA-Board Block Diagram 94
14.21. HC and K-Board Block Diagram 95
14.22. H-Board (1 of 3) Schematic Diagram 96
14.23. H-Board (2 of 3) Schematic Diagram 97
14.24. H-Board (3 of 3) Schematic Diagram 98
14.25. HC, K and TA-Board Schematic Diagram 99
14.26. DG-Board (1 of 3) Block Diagram 100
14.27. DG-Board (2 of 3) Block Diagram 101
3
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

14.28. DG-Board (3 of 3) Block Diagram 102
14.29. DG-Board (1 of 8) Schematic Diagram 103
14.30. DG-Board (2 of 8) Schematic Diagram 104
14.31. DG-Board (3 of 8) Schematic Diagram 105
14.32. DG-Board (4 of 8) Schematic Diagram 106
14.33. DG-Board (5 of 8) Schematic Diagram 107
14.34. DG-Board (6 of 8) Schematic Diagram 108
14.35. DG-Board (7 of 8) Schematic Diagram 109
14.36. DG-Board (8 of 8) Schematic Diagram 110
14.37. XV-Board Block Diagram (PD60B) 111
14.38. XV-Board (1 of 5) Schematic Diagram (PD60B) 112
14.39. XV-Board (2 of 5) Schematic Diagram (PD60B) 113
14.40. XV-Board (3 of 5) Schematic Diagram (PD60B) 114
14.41. XV-Board (4 of 5) Schematic Diagram (PD60B) 115
14.42. XV-Board (5 of 5) Schematic Diagram (PD60B) 116
14.43. D-Board Block Diagram 117
14.44. D-Board (1 of 6) Schematic Diagram 118
14.45. D-Board (2 of 6) Schematic Diagram 119
14.46. D-Board (3 of 6) Schematic Diagram 120
14.47. D-Board (4 of 6) Schematic Diagram 121
14.48. D-Board (5 of 6) Schematic Diagram 122
14.49. D-Board (6 of 6) Schematic Diagram 123
14.50. C1 and C2 Block Diagram 124
14.51. C1-Board (1 of 2) Schematic Diagram (37inch) 125
14.52. C1-Board (2 of 2) Schematic Diagram (37inch) 126
14.53. C1-Board (1 of 2) Schematic Diagram (42inch) 127
14.54. C1-Board (2 of 2) Schematic Diagram (42inch) 128
14.55. C2-Board (1 of 2) Schematic Diagram (37inch) 129
14.56. C2-Board (2 of 2) Schematic Diagram (37inch) 130
14.57. C2-Board (1 of 2) Schematic Diagram (42inch) 131
14.58. C2-Board (2 of 2) Schematic Diagram (42inch) 132
14.59. SC, SU and SD-Board Block Diagram 133
14.60. SC-Board (1 of 2) Schematic Diagram 134
14.61. SC-Board (2 of 2) Schematic Diagram 135
14.62. SU-Board Schematic Diagram (37inch) 136
14.63. SU-Board Schematic Diagram (42inch) 137
14.64. SD-Board Schematic Diagram (37inch) 138
14.65. SD-Board Schematic Diagram (42inch) 139
14.66. SS and S-Board Block Diagram 140
14.67. SS and S-Board Schematic Diagram 141
15 Parts Location & Mechanical Replacement Parts List 143
15.1. Parts Location 143
15.2. Packing Exploded Views (1) 144
15.3. Packing Exploded Views (2) 145
15.4. Packing Exploded Views (3) 146
15.5. Packing Exploded Views (4) 147
15.6. Mechanical Replacement Parts List (PDP TV) 148
15.7. Mechanical Replacement Parts List (Stand) 150
16 Electrical Replacement Parts List 151
16.1. Replacement Parts List Notes 151
16.2. Electrical Replacement Parts List (37inch) 152
16.3. Electrical Replacement Parts List (42inch) 180
4
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

1 Applicable signals
5
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

2 Safety Precautions
2.1. General Guidelines
1.When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
2.After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
3.After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
2.2. Touch-Current Check
1.Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2.Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground such
as a water pipe, as shown in Figure 1.
3.Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4.Check each exposed metallic part, and measure the voltage at each point.
5.Reserve the AC plug in the AC outlet and repeat each of the above measure.
6.The potential at any point (TOUGH CURRENT) expressed as voltage U1and U2, does not exceed the following values:
For a. c.: U1= 35 V (peak) and U2= 0.35 V (peak);
For d. c.: U1=1.0V,
Note:
The limit value of U2= 0.35 V (peak) for a. c. and U1= 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0
mA d. c.
The limit value U1= 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.
7.In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the customer.
Figure 1
6
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electro static discharge (ESD).
1.Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2.After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alminum
foil, to prevent electrostatic charge buildup or exposure of the assembly.
3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4.Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, alminum foil or comparable
conductive material).
7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8.Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
7
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

4 About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol stamped on the back of PCB.
Caution
· Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
· Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
· After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto
the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
8
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

5 Service Hint
Board Name Function Board Name Function
PPower Supply C1 Data Driver (Lower Right)
PA DC-DC Converter, Speaker out, Audio AMP C2 Data Driver (Lower Left)
HAV Terminal, AV Switch, MSP SC Scan Drive
TA Tuner SU Scan out (Upper)
DG Digital Signal Processor, Micom, HDMI Interface SD Scan out (Lower)
XV D-TV Interface (PD60B only) SS Sustain Drive
DFormat Converter, Plasma AI, Sub-Field Processor KRemote receiver, Power LED, Key Switch
HC Jig Connection SPower Switch
9
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.1. Remove the Back cover
1.See Service Hint (Section 5)
6.2. Remove the tuner cover
1.Remove the screws (×9 ,×7 ,×2 ).
2.Remove the tuner cover.
6.3. Remove the P-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for
discharge from electrolysis capacitors.
1.Unlock the cable clampers to free the cable.
2.Disconnect the couplers (P2, P5, P9, P10, P11, P12, P23,
and P25).
3.Remove the screws (×7 ) and remove the P-Board.
6.4. Remove the PA-Board
1.Unlock the cable clampers to free the cable.
2.Disconnect the couplers (PA2, PA5, PA10 and PA40).
3.Disconnect the flexible cable (PA20).
4.Remove the screws (×4 ).
5.Remove the PA-Board.
6 Plasma panel replacement method
10
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.5. Remove the tuner unit
1.Unlock the cable clampers to free the cable.
2.Disconnect the couplers (DG5, H53 and PA40).
3.Disconnect the flexible cables (DG3 and PA20).
4.Remove the screws (×4 ) remove the tuner unit.
6.6. Remove the XV-Board (PD60B)
1.Unlock the cable clampers to free the cable.
2.Disconnect the tuner cable.
3.Remove the screws (×5 ) remove the XV-Board.
(Be careful the coupler (XV01-DG22) when remove the XV-
Board.)
6.7. Remove the DG-Board
1.Remove the XV-Board (PD60B). (See section 6.6.)
2.Remove the screws (×8 ) and remove the XV-Board
metal frame (PD60B).
3.Disconnect the coupler (DG2).
4.Disconnect the flexible cables (DG1, DG15 and DG20).
5.Remove the screw (×1 ) remove the DG-Board.
11
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.8. Remove the TA-Board
1.Disconnect the tuner cable.
2.Remove the screw (×1 ) and remove the TA-Board.
6.9. Remove the H-Board
1.Remove the TA-Board.
2.Unlock the cable clampers to free the cable.
3.Disconnect the couplers (H2 and H40).
4.Disconnect the flexible cable (H1).
5.Remove the screws (×5 ) and remove the H-Board.
6.10. Remove the HC-Board
1.Disconnect the flexible cable (HC15).
2.Remove the screws (×2 ) and remove the HC-Board.
6.11. Remove the D-Board
1.Remove the tuner unit. (See section 6.5.)
2.Disconnect the couplers (D5, D20 and D25).
3.Disconnect the flexible cables (D3, D31 and D32).
4.Remove the screws (×4 ) and remove the D-Board.
12
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.12. Remove the SU-Board
1.Remove the screws (×2 ).
2.Remove the flexible cables (SU1, SU2 and SU3) and
remove the bridge connector (SU45).
3.Slide the SU-Board to the left to disconnect from a coupler
(SC41-SU41) on the SC-Board and remove the SU-Board.
6.13. Remove the SD-Board
1.Remove the screws (×2 ).
2.Remove the flexible cables (SD1, SD2 and SD3) and
remove the bridge connector (SD46).
3.Slide the SD-Board to the left to disconnect from a coupler
(SC42-SD42) on the SC-Board and remove the SD-Board.
13
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.14. Remove the SC-Board
1.Unlock the cable clampers to free the cable.
2.Disconnect the couplers (SC2, SC20 and SC23).
3.Remove the screws (×6 ) and remove the SC-Board.
6.15. Remove the SS-Board
1.Disconnect the couplers (SS1, SS11, SS12 and SS23).
2.Disconnect the flexible cables (SS41A, SS42A, SS43A and
SS44A) (37inch).
Disconnect the flexible cables (SS41, SS42, SS43 and
SS44) (42inch).
3.Remove the screws (×6 ) and remove the SS-Board.
6.16. Remove the C1-Board
1.Remove the tuner unit. (See section 6.5.)
2.Unlock the cable clampers to free the cable.
3.Remove the flexible cables holder fastening screws (×6
).
4.Disconnect the flexible cables (CB1, CB2 and CB3).
5.Disconnect the flexible cables (C11 and C12).
6.Remove the screws (×3 ) and remove the C1-Board.
14
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.17. Remove the C2-Board
1.Remove the tuner unit. (See section 6.5.)
2.Unlock the cable clampers to free the cable.
3.Remove the flexible cables holder fastening screws (×8
).
4.Disconnect the flexible cables (CB4, CB5, CB6 and CB7).
5.Disconnect the flexible cables (C21 and C22).
6.Disconnect the coupler (C23).
7.Remove the screws (×4 ) and remove the C2-Board.
6.18. Remove the speaker L, R
1.Remove the sponge
2.Disconnect the relay couplers
3.Remove the screws (×4 each) and remove the speaker
L, R.
15
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.19. Remove the S-Board
1.Remove the screw (×2 ) and remove the S-Board unit.
2.Unlock the cable clampers to free the cable.
3.Disconnect the coupler (S1).
4.Remove the screws (×2 ) and remove the S-Board.
6.20. Remove the K-Board
1.Unlock the cable clampers to free the cable.
2.Disconnect the coupler (H53). (see section 6.5.)
3.Remove the screws (×3 ) and remove the K-Board.
6.21. Remove the stand brackets
1.Remove the plasma panel section from the servicing stand
and lay on a fiat surface such as a table (covered) with the
plasma panel surface facing downward.
2.Remove the stand brackets (left, right) fastening screws (×6
each) and remove the stand brackets (left, right).
16
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

6.22. Remove the Plasma panel
section from the Front frame
(glass)
1.Remove the front frame and the plasma panel fastening
screws (×8 ).
2.Remove the front frame and the stand brackets fastening
screws (×6 ).
3.For leaving the plasma panel from the front frame, pull the
bottom of the front frame forward, lift, and remove.
6.23. Replace the plasma panel
(finished)
1.Place the new plasma panel (finished) on the flat surface of
the table (covered by a soft cloth), with the plasma panel
surface facing downward.
2.Attach the C1-Board and the C2-Board, connect the flexible
cables (×7) from the Plasma panel to the C1-Board and the
C2-Board, and fit the flexible cable holders.
3.Attach the Hooks (left, right) and fit the stand brackets (L,
R) to the new plasma panel.
4.Place the plasma panel section on the servicing stand.
5.Attach the front frame and each P.C.Board and so on, to
the new plasma panel.
* When fitting the front frame, be careful to allow any
debris, dust or handling residue to remain between the
front glass and plasma panel.
17
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

7 Location of Lead Wiring
7.1. Lead of Wiring (1)
18
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

7.2. Lead of Wiring (2)
19
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B

7.3. Lead of Wiring (3)
20
TH-37PA60E / TH-37PD60B / TH-42PA60E / TH-42PD60B