Panasonic Viera TH-58PZ700B User manual

©2007 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
GPF10DE Chassis
Plasma Television
Specifications
Powe
r
Source
A
C 220-240 V, 50
/
60 Hz
Powe
r
Consumption
Aver
a
ge use 675 W
Standby condition 0.4 W (Without DVB recording)
20 W (With DVB recording)
Displa
y
panel
Aspect Ratio 16 : 9
V
isible screen size 147 cm (diagonal)
1,284 mm (W) × 723 mm (H)
Numbe
r
o
f
pixels 2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots]
Sound
Speake
r
Woofe
r
( 80 mm) × 2 pcs, Tweeter (23 mm × 100 mm) × 2 pcs
Audio Output 31 W [15.5 W + 15.5 W], 10 % THD
Headphones M3 (3.5 mm) stereo mini Jack × 1
PC signals VGA, SVGA, XGA
SXGA ...... (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems/Band name PAL B, G, H, I, SEC
A
M B, G, SEC
A
ML
/
L’
(Except B model) VHF E2 - E12 VHF H1 - H2 (ITALY)
VHF A - H (ITALY) UHF E21 - E69
CATV (S01 - S05) CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)
PAL D, K, SEC
A
MD,
K
VHF R1 - R2 VHF R3 - R5
VHF R6 - R12 UHF E21 - E69
PAL 525/60 Playback of NTSC tape from some PAL Video recorders
(VCR)
ORDERNO.PCZ0708082CE

1 Applicable signals 5
2 Safety Precautions 6
2.1. General Guidelines 6
2.2. Touch-Current Check 6
3 Prevention of Electrostatic Discharge (ESD) to
Electrostatically Sensitive (ES) Devices 7
4 About lead free solder (PbF) 8
5 Service Hint 9
6 Plasma panel replacement method 10
DVB (E model only) Digital terrestrial services via VHF / UHF aerial input.
M.NTSC Playback from M. NTSC Video recorders (VCR)
NTSC (A
V
input only) Playback from NTSC Video recorders (VCR)
lTV signals ma
y
not be received in some areas.
Receiving Systems
/
Band name PAL I UHF E21-68
(B model) PAL 525/60 Playback of NTSC tape from some PAL Video recorders
(VCR) or NTSC disc playback from DVD player and
recorder.
DVB Digital terrestrial services via UHF aerial input.
M.NTSC Playback from M. NTSC Video recorders (VCR)
NTSC (A
V
input only) Playback from NTSC Video recorders (VCR)
Aerial - Rea
r
VHF / UHF (Except B model), UHF (B)
Operating Conditions Temperatu
r
e:0C-35C
Humidity: 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Sca
r
t terminal) 21 Pin terminal (Audio
/
Video in, Audio
/
Video out, RGB in)
AV2 (Sca
r
t terminal) 21 Pin terminal (Audio
/
Video in, Audio
/
Video out, S-Video in, Q-Link)
AV3 (Sca
r
t terminal) 21 Pin terminal (Audio
/
Video in, Audio
/
Video out, RGB in, S-Video in, Q-Link)
AV
4
V
IDEO RCA PIN Type × 1 1.0 V [p-p] (75 ohm)
S-
V
IDEO Mini DIN 4-pin Y: 1.0 V [p-p] (75 ohm) C: 0286V [p-p] (75 ohm)
AUDIO L-R RCA PIN Type × 2 0.5 V [rms]
COMPONENT
V
IDEO
Y
Y: 1.0 V [p-p] (including synchronization)
PB
/
PR± 0.35 V [p-p]
AUDIO L-R RCA PIN Type × 2 0.5 V [rms]
Others
HDMI 1/2/3 Input TYPE A Connectors
·
This TV supports “HDAVI Cont
r
ol 2” function
PC HIGH-DENSITY D-SUB 15PIN R,G,B
/
0.7 V [p-p] (75 ohm)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
Card slot SD CARD slot × 1
Output
AUDIO L-R RCA PIN Type × 2 0.5 V[rms] (high impedance)
DIGITAL AUDIO OUT PCM / Dolb
y
Digital, Fibe
r
optic
Dimensions (W × H × D) 1,454 mm × 918 mm × 144 mm
Mass 65.0 kg Net
Note:
· Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.
· This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.
CONTENTS
Page Page
2
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.1. Remove the Back cover 10
6.2. Remove the fan 10
6.3. Remove the rear terminal cover 10
6.4. Remove the P-Board 10
6.5. Remove the tuner unit 12
6.6. Remove the DH-Board 12
6.7. Remove the DG-Board 13
6.8. Remove the H-Board 13
6.9. Remove the speaker box assy (left, right) 13
6.10. Remove the JG-Board 14
6.11. Remove the PA-Board 14
6.12. Remove the D-Board 14
6.13. Remove the SU-Board 15
6.14. Remove the SD-Board 15
6.15. Remove the SC-Board 15
6.16. Remove the SS2-Board 15
6.17. Remove the SS3-Board 16
6.18. Remove the SS-Board 16
6.19. Remove the C1-Board 16
6.20. Remove the C2-Board 16
6.21. Remove the C3-Board 17
6.22. Remove the C4-Board 17
6.23. Remove the C5-Board 17
6.24. Remove the C6-Board 17
6.25. Remove the stand brackets and rear mounting metals 18
6.26. Remove the front bracket 18
6.27. Remove the G-Board and GH-Board 18
6.28. Remove the GS-Board 18
6.29. Remove the S-Board 19
6.30. Remove the K-Board 19
6.31. Remove the Plasma panel section from the Cabinet assy
(glass) 19
6.32. Remove the squawker speaker 20
6.33. Replace the plasma panel (finished) 20
7 Caution statement 21
7.1. Caution statement. 21
8 Location of Lead Wiring 22
8.1. Lead of Wiring (1) 22
8.2. Lead of Wiring (2) 23
9 Self-check Function 24
9.1. Check of the IIC bus lines 24
9.2. Power LED Blinking timing chart 25
9.3. No Power 26
9.4. No Picture 27
9.5. Local screen failure 28
10 Service Mode 29
10.1. How to enter into Service Mode 29
10.2. Service tool mode 31
11 Adjustment Procedure 32
11.1. Driver Set-up 32
11.2. Initialization Pulse Adjust 33
11.3. P.C.B. (Printed Circuit Board) exchange 33
11.4. Adjustment Volume Location 34
11.5. Test Point Location 34
12 Adjustment 35
12.1. Sub-Contrast adjustment 35
12.2. PAL panel white balance adjustment 36
12.3. HD white balance adjustment 37
13 Hotel mode 38
14 Conductor Views 39
14.1. P(1)-Board 39
14.2. P(2)-Board 42
14.3. PA-Board 45
14.4. G-Board 46
14.5. H-Board 47
14.6. GH and GS-Board 49
14.7. JG-Board 50
14.8. DG-Board 52
14.9. DH-Board 55
14.10. D-Board 56
14.11. C1-Board 58
14.12. C2-Board 59
14.13. C3-Board 60
14.14. C4-Board 61
14.15. C5-Board 62
14.16. C6-Board 63
14.17. SC-Board 64
14.18. SU-Board 67
14.19. SD-Board 68
14.20. SS-Board 69
14.21. K and S-Board 72
15 Schematic and Block Diagram 73
15.1. Schematic Diagram Note 73
15.2. Main Block Diagram 74
15.3. P-Board (1 of 2) Block Diagram 75
15.4. P-Board (2 of 2) Block Diagram 76
15.5. P-Board (1 of 2) Schematic Diagram 77
15.6. P-Board (2 of 2) Schematic Diagram 78
15.7. PA-Board Block Diagram 79
15.8. PA-Board (1 of 2) Schematic Diagram 80
15.9. PA-Board (2 of 2) Schematic Diagram 81
15.10. G, and S-Board Schematic Diagram 82
15.11. H-Board (1 of 2) Block Diagram 83
15.12. H-Board (2 of 2) Block Diagram 84
15.13. H-Board (1 of 5) Schematic Diagram 85
15.14. H-Board (2 of 5) Schematic Diagram 86
15.15. H-Board (3 of 5) Schematic Diagram 87
15.16. H-Board (4 of 5) Schematic Diagram 88
15.17. H-Board (5 of 5) Schematic Diagram 89
15.18. GH and K-Board Schematic Diagram 90
15.19. GS-Board Block Diagram 91
15.20. GS-Board Schematic Diagram 92
15.21. JG-Board Block Diagram 93
15.22. JG-Board (1 of 5) Schematic Diagram 94
15.23. JG-Board (2 of 5) Schematic Diagram 95
15.24. JG-Board (3 of 5) Schematic Diagram 96
15.25. JG-Board (4 of 5) Schematic Diagram 97
15.26. JG-Board (5 of 5) Schematic Diagram 98
3
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

15.27. DG-Board (1 of 3) Block Diagram 99
15.28. DG-Board (2 of 3) Block Diagram 100
15.29. DG-Board (3 of 3) Block Diagram 101
15.30. DG-Board (1 of 12) Schematic Diagram 102
15.31. DG-Board (2 of 12) Schematic Diagram 103
15.32. DG-Board (3 of 12) Schematic Diagram 104
15.33. DG-Board (4 of 12) Schematic Diagram 105
15.34. DG-Board (5 of 12) Schematic Diagram 106
15.35. DG-Board (6 of 12) Schematic Diagram 107
15.36. DG-Board (7 of 12) Schematic Diagram 108
15.37. DG-Board (8 of 12) Schematic Diagram 109
15.38. DG-Board (9 of 12) Schematic Diagram 110
15.39. DG-Board (10 of 12) Schematic Diagram 111
15.40. DG-Board (11 of 12) Schematic Diagram 112
15.41. DG-Board (12 of 12) Schematic Diagram 113
15.42. DH-Board Block Diagram 114
15.43. DH-Board (1 of 4) Schematic Diagram 115
15.44. DH-Board (2 of 4) Schematic Diagram 116
15.45. DH-Board (3 of 4) Schematic Diagram 117
15.46. DH-Board (4 of 4) Schematic Diagram 118
15.47. D-Board (1 of 2) Block Diagram 119
15.48. D-Board (2 of 2) Block Diagram 120
15.49. D-Board (1 of 8) Schematic Diagram 121
15.50. D-Board (2 of 8) Schematic Diagram 122
15.51. D-Board (3 of 8) Schematic Diagram 123
15.52. D-Board (4 of 8) Schematic Diagram 124
15.53. D-Board (5 of 8) Schematic Diagram 125
15.54. D-Board (6 of 8) Schematic Diagram 126
15.55. D-Board (7 of 8) Schematic Diagram 127
15.56. D-Board (8 of 8) Schematic Diagram 128
15.57. C1, C2, C5 and C6-Board Block Diagram 129
15.58. C2, C3, C4 and C5-Board Block Diagram 130
15.59. C1-Board (1 of 2) Schematic Diagram 131
15.60. C1-Board (2 of 2) Schematic Diagram 132
15.61. C2-Board (1 of 2) Schematic Diagram 133
15.62. C2-Board (2 of 2) Schematic Diagram 134
15.63. C3-Board (1 of 2) Schematic Diagram 135
15.64. C3-Board (2 of 2) Schematic Diagram 136
15.65. C4-Board (1 of 2) Schematic Diagram 137
15.66. C4-Board (2 of 2) Schematic Diagram 138
15.67. C5-Board (1 of 2) Schematic Diagram 139
15.68. C5-Board (2 of 2) Schematic Diagram 140
15.69. C6-Board (1 of 2) Schematic Diagram 141
15.70. C6-Board (2 of 2) Schematic Diagram 142
15.71. SC-Board Block Diagram 143
15.72. SC-Board (1 of 2) Schematic Diagram 144
15.73. SC-Board (2 of 2) Schematic Diagram 145
15.74. SU and SD-Board Block Diagram 146
15.75. SU-Board (1 of 3) Schematic Diagram 147
15.76. SU-Board (2 of 3) Schematic Diagram 148
15.77. SU-Board (3 of 3) Schematic Diagram 149
15.78. SD-Board (1 of 3) Schematic Diagram 150
15.79. SD-Board (2 of 3) Schematic Diagram 151
15.80. SD-Board (3 of 3) Schematic Diagram 152
15.81. SS, SS2 and SS3-Board Block Diagram 153
15.82. SS-Board (1 of 2) Schematic Diagram 154
15.83. SS-Board (2 of 2), SS2 and SS3 Schematic Diagram 155
16 Exploded Views & Replacement Parts List 157
16.1. Exploded Views 157
16.2. Fan Exploded Views 158
16.3. Packing Exploded Views (1) 159
16.4. Packing Exploded Views (2) 160
16.5. Packing Exploded Views (3) 161
16.6. Replacement Parts List Notes 162
16.7. Mechanical Replacement Parts List 163
16.8. Electrical Replacement Parts List 165
4
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

1 Applicable signals
5
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

2 Safety Precautions
2.1. General Guidelines
1.When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.
2.When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the wires
have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.
3.When conducting repairs and servicing, do not twist the Faston connectors but plug them straight in or unplug them straight out.
4.When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.
5.After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.
6.After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
2.2. Touch-Current Check
1.Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.
2.Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground such
as a water pipe, as shown in Figure 1.
3.Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network.
4.Check each exposed metallic part, and measure the voltage at each point.
5.Reserve the AC plug in the AC outlet and repeat each of the above measure.
6.The potential at any point (TOUGH CURRENT) expressed as voltage U1and U2, does not exceed the following values:
For a. c.: U1= 35 V (peak) and U2= 0.35 V (peak);
For d. c.: U1= 1.0 V,
Note:
The limit value of U2= 0.35 V (peak) for a. c. and U1= 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0
mA d. c.
The limit value U1= 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz.
7.In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be
repaired and rechecked before it is returned to the customer.
Figure 1
6
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

3 Prevention of Electrostatic Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1.Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2.After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3.Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4.Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5.Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6.Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable
conductive material).
7.Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8.Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
7
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

4 About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
· Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher.
Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
· Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb
solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
· After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto
the opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder.
However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
8
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

Remove the Rear Cover
5 Service Hint
Board Name Function Board Name Function
P Power Supply D Format Converter, Plasma AI, Sub-Field Processor
PA Fan control C1 Data Driver (Upper Right)
H Speaker out, Sound Processor
AV Terminal, AV Switch C2 Data Driver (Upper Center)
C3 Data Driver (Upper Left)
DG DC-DC Converter
Digital Signal Processor, Microcomputer
HDMI Interface, Peaks Lite 2
C4 Data Driver (Lower Left)
C5 Data Driver (Lower Center)
C6 Data Driver (Lower Right)
DH Full HD SC Scan Drive
G Front terminal, Key Switch SU Scan out (Upper)
K Remote receiver, Power LED SD Scan out (Lower)
S Power Switch SS Sustain Drive
GS SD Card Slot SS2 Sustain Connector (Upper)
JG H264 Decorder SS3 Sustain Connector (Lower)
GH HDMI3 terminal
9
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.1. Remove the Back cover
1.See Service Hint. (Section 5)
6.2. Remove the fan
1.Disconnect the relay connectors.
2.Remove the screws (×3 each) and remove the fan A and
fan B.
6.3. Remove the rear terminal
cover
1.Remove the screws (×6 , ×12 ,×2 ).
2.Remove the rear terminal cover.
6.4. Remove the P-Board
Caution:
To remove P.C.B. wait 1 minute after power was off for
discharge from electrolysis capacitors.
1.Unlock the cable clampers to free the cable.
2.Disconnect the connectors (P2, P5, P9, P10, P11, P12, P23
and P25).
3.Remove the screws (×8 ) and remove the P-Board unit.
4.Remove the screws (×28 ) on the back side.
6 Plasma panel replacement method
10
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

5.Disconnect the connectors (CN06-CN02, CN08-CN1602
and CN1701-CN1601).
6.Remove the screws (×12 ).
7.Remove the molding props (×8 ).
8.Remove the P(Multi)-Board.
9.Remove the molding props (×13 ).
10.Remove the P(Sus)-Board.
Note:
When assembling the P(Multi)-Board and the P(Sus)-
Board, the position of each hole of the insulation sheets(A,
B, C, D) is set to the position of each hole of the P(Multi)-
Board and the P(Sus)-Board and then assemble them. (
marks indicate setting positions.)
P-Board back side
11
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

P-Board back side
6.5. Remove the tuner unit
1.Unlock the cable clampers to free the cable.
2.Disconnect the connectors (DG1, DG11, DG23, DG35,
DG52, DH5, DH8, H3, H8, H11, H12 and H51).
3.Remove the screws (×4 ) and remove the tuner unit.
6.6. Remove the DH-Board
1.Remove the tuner unit. (See section 6.5.)
2.Remove the screws (×4 ) and remove the DH-Board
cover and DH-Board.
(Be careful the connector (DH25-DG25) when remove the
DH-Board.)
3.Remove the screw (×1 ) and remove the DH-Board from
DH-Board cover.
4.Remove the screws (×4 ) and remove the DH-Board
frame.
12
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.7. Remove the DG-Board
1.Remove the tuner unit. (See section 6.5.)
2.Remove the DH-Board and the DH-Board frame. (See
section 6.6.)
3.Disconnect the connector (DG2 and DG6).
4.Remove the screws (×7 ) and remove the DG-Board.
6.8. Remove the H-Board
1.Remove the tuner unit. (See section 6.5.)
2.Remove the DH-Board and the DH-Board frame. (See
section 6.6.)
3.Remove the screws (×1 ,×1 ) and remove the tuner
fixing metal.
4.Disconnect the connector (H2 and H6).
5.Remove the screws (×7 ) and remove the H-Board.
6.9. Remove the speaker box assy
(left, right)
1.Unlock the cable clampers to free the cable.
2.Disconnect the relay connectors.
3.Remove the screw (×1 ) and remove the speaker box
assy (left, right).
13
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.10. Remove the JG-Board
1.Disconnect the connector (JG8, JG9, JG10 and JG19).
2.Remove the screws (×4 ) and remove the JG-Board.
6.11. Remove the PA-Board
1.Unlock the cable clampers to free the cable.
2.Disconnect the connectors (PA3, PA5, PA9, PA10, PA34,
PA35 and PA38).
3.Remove the screws (×4 ) and remove the PB-Board.
4.Remove the JG-Board. (See section 6.10.)
5.Remove the screws (×4 ) and remove the PA-Board
fixing metal.
6.12. Remove the D-Board
1.Remove the PA-Board fixing metal. (See section 6.11.)
2.Disconnect the connectors (D3, D5, D20 and D25).
3.Disconnect the flexible cables (D31, D32, D33, D34, D35
and D36).
4.Remove the screws (×4 ) and remove the D-Board.
14
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.13. Remove the SU-Board
1.Remove the screws (×4 ).
2.Remove the flexible cables (SU1, SU2, SU3, SU4 and SU5)
connected to the SU-Board and remove the connectors
(SC45-SU45).
3.Slide the SU-Board to the left to disconnect from
connectors (SC41-SU41 and SC42-SU42) on the SC-Board
and remove the SU-Board.
6.14. Remove the SD-Board
1.Remove the screws (×4 ).
2.Remove the flexible cables (SD1, SD2, SD3, SD4 and SD5)
connected to the SD-Board and remove the connector
(SC46-SD46).
3.Slide the SD-Board to the left to disconnect from
connectors (SC43-SD43 and SC44-SD44) on the SC-Board
and remove the SD-Board.
6.15. Remove the SC-Board
1.Unlock the cable clampers to free the cable.
2.Remove the SU-Board and SD-Board. (See section 6.13.
and 6.14.)
3.Disconnect the connectors (SC2, SC20 and SC23).
4.Remove the screws (×10 ) and remove the SC-Board.
6.16. Remove the SS2-Board
1.Disconnect the connector (SS23) and disconnect the
flexible cable (SS55).
2.Remove the screws (×2 ) and remove the SS2-Board.
15
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.17. Remove the SS3-Board
1.Disconnect the connector (SS22) and disconnect the
flexible cable (SS56).
2.Remove the screws (×2 ) and remove the SS3-Board.
6.18. Remove the SS-Board
1.Disconnect the connectors (SS11, SS12, SS22, SS23,
SS35, SS42 and SS44).
2.Remove a short-jumper connector SS34 and re-use for new
SS-Board.
3.Disconnect the flexible cables (SS53, SS54, SS55 and
SS56).
4.Remove the screws (×10 ) and remove the SS-Board.
6.19. Remove the C1-Board
1.Remove the fan. (See section 6.2.)
2.Remove the flexible cables holder fastening screws (×10
).
3.Disconnect the flexible cables (CA1, CA2, CA3, CA4, and
CA5).
4.Disconnect the flexible cables (C10 and C11).
5.Remove the screws (×6 ) and remove the C1-Board.
6.20. Remove the C2-Board
1.Remove the fans. (See section 6.2.)
2.Remove the flexible cables holder fastening screws (×10
).
3.Disconnect the flexible cables (CA6, CA7, CA8, CA9 and
CA10).
4.Disconnect the flexible cables (C21, C22, C24 and C25).
5.Remove the screws (×6 ) and remove the C2-Board.
16
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.21. Remove the C3-Board
1.Remove the fans. (See section 6.2.)
2.Remove the flexible cables holder fastening screws (×10
).
3.Disconnect the flexible cables (CA11, CA12, CA13, CA14
and CA15).
4.Disconnect the flexible cable (C31).
5.Disconnect the connector (C35).
6.Remove the screws (×6 ) and remove the C3-Board.
6.22. Remove the C4-Board
1.Remove the speaker box assy left. (See section 6.9.)
2.Remove the flexible cables holder fastening screws (×10
).
3.Disconnect the flexible cables (CB11, CB12, CB13, CB14
and CB15).
4.Disconnect the flexible cable (C41).
5.Disconnect the connectors (C42 and C44).
6.Remove the screws (×6 ) and remove the C4-Board.
6.23. Remove the C5-Board
1.Remove the tuner unit. (See section 6.5.)
2.Remove the flexible cables holder fastening screws (×10
).
3.Disconnect the flexible cables (CB6, CB7, CB8, CB9 and
CB10).
4.Disconnect the flexible cables (C51, C52, C54 and C55).
5.Remove the screws (×6 ) and remove the C5-Board.
6.24. Remove the C6-Board
1.Remove the speaker box assy right. (See section 6.9.)
2.Remove the flexible cables holder fastening screws (×10
).
3.Disconnect the flexible cables (CB1, CB2, CB3, CB4 and
CB5).
4.Disconnect the flexible cables (C60 and C61).
5.Remove the screws (×6 ) and remove the C6-Board.
17
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.25. Remove the stand brackets
and rear mounting metals
1.Remove the plasma panel section from the servicing stand
and lay on a flat surface such as a table (covered) with the
plasma panel surface facing downward.
2.Remove the stand brackets (left, right) fastening screw (×
1each).
3.Remove the rear mounting metals (left, right) fastening
screws (×4 each).
4.Remove the stand brackets and rear mounting metals.
5.Remove the fastening screws (×4 each).
6.Remove the stand brackets from rear mounting metals.
6.26. Remove the front bracket
1.Unlock the cable clampers to free the cable.
2.Remove the screws (×3 ) and remove the front bracket.
6.27. Remove the G-Board and GH-
Board
1.Remove the front bracket. (See section 6.26.)
2.Remove the screws (×4 ) and remove the front shield
case (front).
3.Remove the screws (×4 ) and disconnect the connector
(G51, G52 and GH11).
4.Remove the G-Board and GH-Board.
6.28. Remove the GS-Board
1.Remove the stand bracket right and rear mounting metal
right. (See section 6.25.)
2.Unlock the cable clampers to free the cable.
3.Remove the screws (×2 ).
4.Remove the SD card unit.
5.Disconnect the connector (GS09 and GS52).
6.Remove the screw (×1 ).
7.Remove the GS-Board.
18
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.29. Remove the S-Board
1.Remove the speaker box assy left. (See section 6.9.)
2.Remove the screws (×2 ) and remove the S-Board unit.
3.Disconnect the connector (S1).
4.Remove the screws (×2 ) and remove the S-Board.
6.30. Remove the K-Board
1.Remove the speaker box assy left. (See section 6.9.)
2.Unlock the cable clampers to free the cable.
3.Remove the screws (×2 ).
4.Disconnect the connectors (K1) and remove the K-Board.
6.31. Remove the Plasma panel
section from the Cabinet assy
(glass)
1.Remove the stand brackets (left, right) fastening screw (×1
each).
2.Remove the cabinet assy and the plasma panel fastening
screws (×14 ).
3.For leaving the plasma panel from the cabinet assy, pull the
bottom of the front frame forward, lift, and remove.
19
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P

6.32. Remove the squawker speaker
1.Remove the cabinet assy. (See section 6.31.)
2.Disconnect the relay connectors.
3.Remove the screws (×12 ).
4.Remove the glass holders (left, right).
5.Remove the screws (×2 ).
6.Remove the squawker speaker.
6.33. Replace the plasma panel
(finished)
1.Place the new plasma panel (finished) on the flat surface of
the table (covered by a soft cloth), with the plasma panel
surface facing downward.
2.Attach the C1, C2, C3,C4,C5-Board and the C6-Board,
connect the flexible cables (×30) from the Plasma panel to
the C1, C2, C3,C4,C5-Board and the C6-Board, and fit the
flexible cable holders.
3.Attach the Hooks (left, right) and fit the Reinforcement
Angles (L, R) and the Connection Plate (A, B, C, D) to the
new plasma panel.
4.Place the plasma panel section on the servicing stand.
5.Attach the cabinet assy and each P.C.Board and so on, to
the new plasma panel.
* When fitting the cabinet assy, be careful not to allow
any debris, dust or handling residue to remain between
the front glass and plasma panel.
20
TH-58PZ700B / TH-58PZ700E / TH-58PY700F / TH-58PY700P