Panasonic PT-RW330U User manual

1-Chip DLP™Projectors
PT-RZ370
PT-RW330
Beyond Ordinary Projection—
Solid Reliability with the
LED/Laser-Combined Light Source

Start projecting as soon as you turn on the power
Many projector issues have
been addressed with the new
LED/Laser-combined light
source. From the moment you
turn on the projector, you’ll
notice the difference with the
quick on and immediate full
brightness. No more lamps
and air filters, which lets you enjoy maintenance-free use for about
20,000 hours*1while maintaining excellent brightness and picture
quality. To enhance permanent installation use, we’ve added DIGITAL
LINK support so you can transmit video, audio and control signals
up to 100 meters (328 feet)
over a single LAN cable.*2
System capabilities have also
been improved with 2×zoom
and an exceptionally wide
lens shift range, thus provid-
ing superb flexibility for easy
first time and replacement
installations. And the Total Cost of Ownership (TCO) has been
reduced because you no longer have to keep replacement lamps on
hand. The next-generation PT-RZ370/RW330 projectors have swept
away the weak points of conventional projectors.
SOLID SHINE series uses the newly developed LED/Laser-combined light source
SOLID SHINE series projectors provide solid
reliability and long-lasting brightness unprece-
dented by conventional lamp-based projectors.
Approximately 20,000 hours*1of maintenance-free operation
No need to replace the light source or air filter, providing a
dramatic reduction in the Total Cost of Ownership (TCO).
Long-lasting picture quality
Excellent picture quality and brightness are maintained for a
long time.
Superb color reproduction
Beautiful, vivid colors exceeding the levels of conventional pro-
jectors.
Quick start, quick off
The image appears almost instantly upon powering up, and
there is no need for cooling after turning the power off. The
power can be turned on immediately after being turned off, and
it can be turned on/off as many times as you want.
Full HD
PT-RZ370
3,500 lm
WXGA
PT-RW330
3,500 lm
PT-RZ370/RW330 Optical Structure Image
Phosphor wheel
(changes from
blue to green)
LED (blue)
LED (red)
Light sensor for
SOLID SHINE drive
Laser (blue)
DLP™ chip
Projection lens
Condenser
lens
1

The LED/Laser-Combined Light Source
Enables Approx. 20,000*1Hours of
Continuous Operation
This new light source requires no maintenance
for approximately 20,000 hours.
*1In many
cases, this means no maintenance until your
next refresh cycle. Naturally, there are no lamp
burnout problems during use, so reliability is
further increased. There is also no filter to clean
due to carefully engineered sealed optics. As
a consequence, running cost is dramatically
lowered because of the savings on lamp
costs, maintenance labor and hassle of
stocking lamps.
Bright, Beautiful Picture Quality for a
Long Period of Time
The PT-RZ370/RW330 features 3,500 lumens of
brightness. Rate of brightness deterioration in
the LED/Laser-combined light source is extreme-
ly slow compared to lamp based projectors. The
SOLID SHINE drive uses a built-in sensor to
constantly detect the light intensity of the light
source and correct corresponding changes in
white balance. This all helps to maintain excel-
lent picture quality for a long period of time.
Contrast is outstanding too, at 10,000:1, and
images are reproduced with a wide dynamic
range. The PT-RZ370 features a Full-HD (1920
×1080) DLP™chip, allowing highly detailed
Full-HD images without resizing.
Superior Color Reproduction
The LED/Laser-combined light source has a
higher level of color purity than an ordinary
lamp, allowing it to achieve color production
with wider color space. Colors are more vibrant
than those of conventional projectors.
30×Drive*3Switching Prevents Color
Breaking
In 1-chip DLP™system projectors with conven-
tional lamp, a color wheel is used for time-divi-
sion multiplexing in a method where the human
eye combines the result to achieve a full-color
palette. In the PT-RZ370/RW330, this is done by
on/off switching of the LED/Laser-combined light
source. A unique Panasonic power supply circuit
provides time-division multiplexing with ultrafast
30×drive.
*3The resulting, high-definition images
exhibit virtually no color breaking.*4
Heat Pipe Cooling System Maintains Stable
Operation up to 45 °C (113 °F)*5
Laser cooling is performed by releasing the heat
to cooling fins, then cooling with a heat pipe
cooling system. This suppresses temperature
rises inside the projector and allows stable
operation up to an ambient temperature of
45 °C (113 °F).*5The use of this heat pipe-
cooled system also achieves quiet operation of
29 dB,
*6enabling viewers to concentrate on the
presentation or on quiet movie scenes.
Dust-Resistant Structure with an Airtight
Optical Block
The area between the LED/Laser to the DLP™
chip and prism is hermetically sealed to form an
airtight structure for the optical block, the heart
of the projector. This resists the effects of dust
and other particles in the air, and enables use of
the projector in a wide range of environments.
The Daylight View Basic Ensures Clear
Images Even in Brightly Lit Rooms
0ANASONICS $AYLIGHT 6IEW "ASIC TECHNOLOGY
achieves sharp, easy-to-see images by clearly
reproducing the details in dark image areas,
which were previously difficult to see in brightly
lit rooms. A built-in sensor measures the ambi-
ent light, and the Daylight View Basic function
adjusts the halftone color and brightness level
according to the surrounding illumination.
DICOM Simulation Mode*7
This imaging mode is similar to DICOM part 14,
which is a medical imaging standard. It repro-
duces X-ray images with remarkable clarity.
Rec. 709 Mode for HDTV Projection
Optimal color reproduction can be achieved by
selecting this mode, compliant with ITU-R Rec-
ommendation BT.709, when images from an
HDTV source are projected.
BRIGHTNESS
HOURS
20,000 hrs
6,000 hrs
Lamp
LED/Laser-combined
light source
020,00010,000
100%
0%
Heat-pipe cooling system
Phosphor wheel
LaserLED (Red) LED (Blue)
Normal mode DICOM simulation mode
Brightness Deterioration Comparison
Comparison with a projector that has a lamp replacement
cycle of 6,000 hours.
Without Daylight View Basic
With Daylight View Basic
Long-Lasting Reliability and High Picture Quality
*1 A guideline for light source replacement. The maintenance-free period may be
shortened due to environmental conditions.
*2 Use a CAT5e (STP) cable or higher.
*3 Picture mode: Dynamic. 10×drive in other picture modes. The rate for each vertical
sync/blanking interval, with R/G/B light source switching set to 1×.
*4 A condition in which incorrect color expression causes color flickering.
*5 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when used in
locations from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level.
*6 LIGHT POWER mode: ECO. 35 dB with LIGHT POWER mode set to NORMAL.
*7 This product is not a medical instrument. Do not use it for actual medical diagnosis.
2

Versatile First-Time and Replacement
Installations
s2×Zoom Lens: For a 120-inch-diagonal
wide screen, the projection distance extends
from approximately 3.9 m (12.8 ft) to approx-
imately 7.8 m (25.7 ft).
sHorizontal/Vertical Lens Shift: The wide
shift range accommodates various room sizes
and shapes. When lights
or ventilation holes are
located in the ceiling
mounting site, you can
simply relocate the pro-
jector to avoid them.
sFlexible 360-Degree Installation: The pro-
jectors can be rotated
vertically. This means
you can install one at
any up-and-down angle
you want, to accommo-
date different installa-
tion conditions.
sLens-Centered Design: A lens-centered,
symmetrical design provides ease of
installation, eliminating
the need for any spe-
cial considerations
when planning the
installation site.
DIGITAL LINK Transmits Digital Signals up
to 100 m (328 ft) with a Single Cable*2
sOptional ET-YFB100G Digital Interface Box
for Easy Setup: By combining the optional
ET-YFB100G Digital Interface Box, with its
HDMI and other input terminals, uncom-
pressed HD digital video, audio and control
signals can be transmitted up to 100 m
(328 ft) over a single LAN cable.*2It allows
projector connection with only one cable,
making it ideal for ceiling-mounted and other
permanent installations. Also, because control
signals can be simultaneously transmitted, the
ET-YFB100G input signal can easily be
switched with the wireless remote control that
is included with the projector. The projector
can be controlled by either serial or LAN
communication.
sAlso Supports Other Manufacturers’
Peripheral Equipment: DIGITAL LINK is an
original function added to technology based
on the transmission standards used in Crest-
ron’s DigitalMedia 8G+, Extron’s XTP Sys-
tems, etc. Signals from the ET-YFB100G can
also be relayed to a non-DIGITAL LINK-ready
projector by using another manufacturer’s
equipment based on the same technology.*8
Abundant Connection Terminals,
Including HDMI
Interfaces include HDMI and DVI-I inputs. The
serial terminal (RS-232C) has an Emulate func-
tion that lets you continue using existing control
systems when replacing previous Panasonic
models. It is also possible to output audio dur-
ing STANDBY MODE.*9This is convenient when
connecting an external audio system through the
projector.*10 A closed caption decoder is built in.
Easy Remote Monitoring and Control
over a LAN
Web browser on a computer connected through
a wired LAN system lets you remotely operate
projectors and check their status. An e-mail
messaging function can also notify you the
overall projector status. In addition, Multi
Projector Monitoring and Control Software Ver.
2.8 is available for monitoring and controlling
multiple Panasonic projectors from a single PC.
The wired LAN terminal is compatible with
PJLink™(class 1), an open protocol that is used
by many manufacturers, to enable integrated
control of systems that contain different brands
of projectors.
Compatible with Crestron RoomView™
The LAN terminal allows a computer connected
to the network to use Crestron RoomView™
application software to manage and control
system devices.
DIGITAL LINK
Digital Interface Box
ET-YFB100G
1-Chip DLP™Projector
PT-RZ370/RW330
Input selection and other ET-YFB100G
operations can be performed with the
projector’s remote control.
CAT5e (STP) cable or higher: Video, audio
and control signals (up to 100 m / 328 ft)
Document
camera
Speaker
Notebook PCDesktop PCVCRHD visual
communication
system
Blu-ray disc
player
VideoRGB signalRGB signal
S-Video/
audio signal
HDMI signal
(video/audio)
HDMI signal
(video/audio)
120-inch
wide screen
Approx. 3.9 m
Approx. 7.8 m
PT-RZ370
ET-YFB100G terminals
PT-RZ370
360°
&OR DETAILS ON OTHER MANUFACTURERS EQUIP-
MENT VISIT OUR 0ROJECTOR 'LOBAL 7EB 3ITE
panasonic.net/avc/projector
Lecture room
Auditorium
Classroom
Seminar room
The projection lens is
placed at the center.
Flexible Installation with Clean DIGITAL LINK Wiring
*8 Input selection and other ET-YFB100G operations can be performed only when connecting to a DIGITAL LINK compatible projector.
*9 Requires menu selection.
*10 Audio monitoring requires external speakers and an audio amplifier.
3

Image Appears Immediately—No Need for
Cooling after Use
Images do not appear quickly with lamp-based
projectors because the projector requires time to
warm up. With the PT-RZ370/RW330, the image
appears almost instantly. There’s also no cooling
time required when turning the power off, so
you can quickly turn the projector on and off as
many times as needed.
24/7 Operation
Ordinary lamps are not well suited to continuous
operation. Because the PT-RZ370/RW330 does
not use a lamp, has efficient cooling system and
uses DLP™chip that has a long life, they are
capable of 24/7 operation.
Scheduling Function
Scheduled operation is possible using the built-
in timer function, without having to use a PC
and software.
Effective Theft Prevention with the
Startup Logo
You can change the default Panasonic start up
logo to any logo you want. A new logo can be
easily uploaded by connecting a computer to the
PT-RZ370/RW330 through the LAN or serial
connection by using the Logo Transfer Soft-
ware.
*11 An abundance of other security mea-
sures are also includ-
ed, such as a security
bar, Key lock, and
Security Password. This
is very effective for
preventing theft.
15 m (49 ft) Long-Range
Wireless Remote Control
A unique ID number can be assigned
to each projector using the supplied
wireless remote control unit. This
allows operation of a desired projec-
tor when multiple units are set up at
the same location. Three frequently
used functions can be assigned to the Function
buttons for instant recall.
Eco Management Functions
A number of functions are provided to reduce
power consumption. You can easily set the Eco
Management functions according to operating
conditions by using the “ECO” button on the
remote control.
sSelectable light source modes:
NORMAL: Prioritizes brightness. ECO SAVE 1:
Reduces power consumption by approximately
20% on average while leaving brightness
almost unchanged. ECO SAVE 2: Minimizes
brightness reduction while reducing power
consumption by approximately 30% on aver-
age. LOW: Prioritizes low power consumption.
sAdjusts the brightness according to ambient
light conditions, and reduces the light source
power.
sReduces the light source power when there is
no signal input or the projector is in AV
Mute mode.
Operation Friendly
*11 Still images that can be uploaded are limited to 1024 ×768 pixel bitmap files. Also,
the application will reduce the number of colors to 191.
Ecology-Conscious Design
sLamp-free (no mercury)
sLow heat dissipation
sRoHS Directive compliant
sNo halogenated flame retardants are used in the cabinet.
sNon-coated cabinet for easy recycling.
sLead-free glass is used for the lens.
sLight source mode is selectable to reduce power consumption.
s“ECO” button on the remote control for easy setting up of Eco Management
functions.
sStandby power consumption of only 0.5 W has been achieved. (STANDBY MODE:
ECO)
sAn Auto Off Timer switches the projector to standby mode when no input
signal is received for a preset time.
ET-PKR100H
Ceiling mount bracket
for high ceilings
Options
ET-PKR100S
Ceiling mount bracket
for low ceilings
ET-YFB100G
Digital interface box
Brackets included for various installation needs,
including server rack (EIA standards) mounting.
PT-RZ370 (16:9 aspect ratio)
PT-RW330 (16:10 aspect ratio)
PT-RW330 (16:9 aspect ratio)
UNIT METERS FEET
Projection Distance
1.02
1.52
2.03
2.54
3.05
3.81
5.08
7.62
1.3
1.9
2.6
3.2
3.9
4.9
6.5
9.8
2.6
3.9
5.2
6.5
7.8
9.8
13.1
19.6
-0.12
-0.17
-0.23
-0.29
-0.34
-0.43
-0.57
-0.86
0.49
0.73
0.98
1.22
1.46
1.83
2.44
3.66
−
−
−
−
−
−
−
−
40
60
80
100
120
150
200
300
/
/
/
/
/
/
/
/
(4.1)
(6.3)
(8.5)
(10.6)
(12.8)
(16.0)
(21.4)
(32.2)
(8.5)
(12.8)
(17.1)
(21.4)
(25.7)
(32.1)
(42.9)
(64.4)
(-0.4
(-0.6
(-0.8
(-0.9
(-1.1
(-1.4
(-1.9
(-2.8
1.6)
2.4)
3.2)
4.0)
4.8)
6.0)
8.0)
12.0)
−
−
−
−
−
−
−
−
Projection size
[diagonal]
[m] [in]
Projection distance
Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens
1.02
1.52
2.03
2.54
3.05
3.81
5.08
7.62
1.3
2.0
2.6
3.3
4.0
5.0
6.7
10.0
2.6
4.0
5.3
6.7
8.0
10.0
13.4
20.1
-0.10
-0.15
-0.21
-0.26
-0.31
-0.38
-0.51
-0.77
0.52
0.78
1.03
1.29
1.55
1.94
2.59
3.88
−
−
−
−
−
−
−
−
40
60
80
100
120
150
200
300
/
/
/
/
/
/
/
/
(4.2)
(6.4)
(8.6)
(10.9)
(13.1)
(16.4)
(21.9)
(32.9)
(8.7)
(13.1)
(17.5)
(21.8)
(26.2)
(32.8)
(43.8)
(65.8)
(-0.3
(-0.5
(-0.7
(-0.8
(-1.0
(-1.3
(-1.7
(-2.5
1.7)
2.5)
3.4)
4.2)
5.1)
6.4)
8.5)
12.7)
−
−
−
−
−
−
−
−
Projection size
[diagonal]
[m] [in]
Projection distance
Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens
1.02
1.52
2.03
2.54
3.05
3.81
5.08
7.62
1.3
2.0
2.7
3.4
4.1
5.1
6.9
10.3
2.7
4.1
5.5
6.8
8.2
10.3
13.7
20.6
-0.05
-0.08
-0.10
-0.13
-0.15
-0.19
-0.25
-0.37
0.48
0.71
0.95
1.19
1.43
1.79
2.38
3.57
−
−
−
−
−
−
−
−
40
60
80
100
120
150
200
300
/
/
/
/
/
/
/
/
(4.4)
(6.6)
(8.9)
(11.2)
(13.5)
(16.9)
(22.5)
(33.9)
(8.9)
(13.4)
(17.9)
(22.4)
(27.0)
(33.7)
(45.0)
(67.6)
(-0.2
(-0.2
(-0.3
(-0.4
(-0.5
(-0.6
(-0.8
(-1.2
1.6)
2.3)
3.1)
3.9)
4.7)
5.9)
7.8)
11.7)
−
−
−
−
−
−
−
−
Projection size
[diagonal]
[m] [in]
Projection distance
Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens
4

Weights and dimensions shown are approximate. Specifications and appearance are subject to
change without notice. Product availability differs depending on region and country. This product
may be subject to export control regulations. DLP, DLP logo and DLP Medallion logo are trademarks
or registered trademarks of Texas Instruments. The projection distances and throw ratios given in
this leaflet are for use only as guidelines. For more detailed information, please consult the dealer
from whom you are purchasing the product. The PJLink trademark is an application trademark in
Japan, the United States, and other countries and regions or registered trademarks. HDMI, the
HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.All other trademarks are the property
of their respective trademark owners. Projection images simulated.
© 2012 Panasonic Corporation. All rights reserved. PT-RZ370G1 Printed in Japan.
All information included here is valid as of December 2012.
For more information about Panasonic projectors, please visit:
Projector Global Web Site – panasonic.net/avc/projector
Facebook – www.facebook.com/panasonicprojector
YouTube – www.youtube.com/user/PanasonicProjector
*1In STANDARD/GRAPHIC picture mode. Measured based on the power consumption rate and a measurement method
for the TV receiver.
*2When the STANDBY MODE is set to ECO, network functions such as power on over the LAN network will not operate.
Also, only certain commands can be received for external control using the serial terminal.
*3Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video
Timing-Reduced Blanking).
*5With legs at shortest position.
*6Average value. May differ depending on the actual unit.
*70–40 °C (32–104 °F) between 1,400 m and 2,700 m (4,593 ft and 8,858 ft) above sea level. If the ambient
temperature exceeds 35 °C (95 °F), the light output may be reduced to protect the projector.
*8Power cords available (×2) for the PT-RZ370EA/RW330EA.
Specifications
fH: 15.75 kHz, fV: 60 Hz [480i (525i)]
fH: 15.63 kHz, fV: 50 Hz [576i (625i)]
fH: 31.50 kHz, fV: 60 Hz [480p (525p)]
fH: 31.25 kHz, fV: 50 Hz [576p (625p)]
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p]
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p]
fH: 33.75 kHz, fV: 60 Hz [1035/60i]
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i]
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i]
fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p]
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p]
fH: 27.00 kHz, fV: 48 Hz [1080 (1125)/24sF]
fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p]
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p]
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
16.5 mm (0.65 in) diagonal (16:9 aspect ratio)
DLP™chip ×1, DLP™projection system
2,073,600 (1,920 ×1,080) ×1, total of 2,073,600 pixels
1.4 6–2.94:1
1.02–7.6 2 m ( 4 0–300 inches) diagonally, 16:9 aspect ratio
1,920 ×1,080 pixels ( Input signals that exceed this resolution will be converted
to 1,920 ×1,080 pixels.)
Vertical: +73%, -48% (manual), horizontal: +27%, -35% (manual)
16.5 mm (0.65 in) diagonal (16:10 aspect ratio)
DLP™chip ×1, DLP™projection system
1,024,000 (1,280 ×800 ) ×1, total of 1,024,000 pixels
1.5–3.1:1
1.02–7.6 2 m ( 4 0–300 inches) diagonally, 16:10 aspect ratio
1,280 ×800 pixels ( Input signals that exceed this resolution will be converted
to 1,280 ×800 pixels.)
–
Vertical: +69%, -46% (manual), horizontal: +28%, -37% (manual)
100–240 V AC, 5.2–2.0 A, 50/60 Hz
460 W (470 VA)(250 W*1with LIGHT POWER set to NORMAL, 200 W*1with LIGHT POWER set to Ecosave1, 178 W*1with LIGHT POWER set to Ecosave2)
(0.5 W with STANDBY MODE set to ECO*2, 8 W with STANDBY MODE set to NORMAL)
Manual zoom (2.0×), manual focus, F 2.0–3.4, f 21.5–43.0 mm
LED/Laser-combined (R, B: LED; G: Laser diode)
3,500 lm
90 %
10,000:1 (full on/off)
fH: 27–100 kHz, fv: 24–120 Hz, dot clock: 25–162 MHz
fH: 15–100 kHz, fv: 24–120 Hz, dot clock: 162 MHz or lower
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Vertical: ±40°
Ceiling/floor, front/rear
HDMI 19-pin ×1 (Deep Color, compatible with HDCP)
480p(525p),576p(625p),720(750)/60p,720(750)/50p,1080(1125)/60i,1080(1125)/50i,1080(1125)/25p,1080(1125)/24p,1080(1125)/24sF,
1080 (1125)/30p, 1080 (1125)/60p, 1080 (1125) /50p, VGA (640 ×4 80 ) –WU XGA*4(1,920 ×1,200), compatible with non-interlaced signals only,
dot clock: 25–162 MHz, audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
DVI-I 29-pin ×1
(DVI 1.0 compliant, compatible with HDCP, compatible with single link only) 480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1080 (1125)/60i,
1080 (1125)/50i, 1080 (1125)/25p, 1080 (1125 )/24p, 1080 (1125)/24sF, 1080 (1125 )/30p, 1080 (1125 )/60p, 1080 (1125)/50p,
VGA (640 ×480)–WUXGA*4(1,920 ×1,200), compatible with non-interlaced signals only, dot clock: 25–162 MHz
R/B: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, HD/VD, SYNC: TTL, high impedance, positive/negative automatic
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
D-Sub HD 15-pin (female) ×1 (RGB/YPBPR/YCBCR×1)
Pin jack ×1
M3 (L, R) ×1
M3 (L, R) ×1
D-sub 9-pin (female) ×1 for external control (RS-232C compliant)
RJ-45 ×1
(for network and DIGITAL LINK (video/audio/network/serial control) connection, 100Base-TX, compatible with PJLink™, HDCP compatible, Deep Color compatible)
1080(1125)/50i,1080(1125)/25p,1080(1125)/24p,1080(1125)/24sF,1080(1125)/30p,1080(1125)/60p,1080(1125)/50p,
VGA (640 ×480)–WUXGA*4(1,920 ×1,200), compatible with non-interlaced signals only, dot clock: 25–162 MHz
Molded plastic
455 ×137*5×415 mm (17-29/32 ×5-13/32*5×16-11/32 in) (lens incuded)
Approximately 11.0 kg (24.3 lbs)
35 dB (LIGHT POWER mode: NORMAL), 29 dB (LIGHT POWER mode: LOW)
Operating temperature: 0–45 °C*7(32–113 °F*7), operating humidity: 20– 80 % (no condensation)
Power cord (with secure lock) ×1*8, wireless remote control unit, batteries for remote control (R6/LR6/AA type ×2), software CD-ROM (Logo Transfer
Software, Multi Projector Monitoring & Control Software)
Model
Power supply
Power consumption
DLP™ chip
Lens
Throw ratio
Light source
Screen size (diagonal)
Brightness*3
Center-to-corner uniformity*3
Contrast*3
Resolution
Scanning frequency
Optical axis shift
Keystone correction range
Installation
Terminals
Cabinet materials
Dimensions (W ×H ×D)
Weight*6
Operation noise*3
Operating environment
Supplied accessories
Panel size
Display method
Pixels
HDMI/DVI-I (digital)
DVI-I (analog)/RGB
YPBPR(YCBCR)
Video
HDMI IN
DVI-D IN
Digital
RGB
YPBPR/YCBCR
COMPUTER (RGB) IN
VIDEO IN
AUDIO IN
AUDIO OUT
SERIAL IN
LAN / DIGITAL LINK
PT-RW330PT-RZ370
455 (17-29/32) 415 (16-11/32)
137
(5-13/32)
Dimensions unit: mm (inches)
1. Do not install the projector in locations that are subject to excessive water, humidity, steam, or
oily smoke. Doing so may result in fire, malfunction, or electric shock.
2. Please observe the following precautions:
s.EVER PLACE OBJECTS ON TOP OF THE PROJECTOR WHILE IT IS OPERATION
s-AKE SURE THERE IS AN UNOBSTRUCTED SPACE OF  MM  FT  IN OR MORE AROUND THE PROJECTORS
exhaust openings.
s$O NOT STACK PROJECTOR UNITS DIRECTLY ON TOP OF ONE ANOTHER FOR THE PURPOSE OF MULTIPLE STACKED
projection. When stacking projector units, be sure to provide the amount of space indicated below
between them. These space requirements also apply to installations where only one projec tor unit
is operating at one time and the other unit is used as a backup.
s-AKE SURE THAT NOTHING BLOCKS THE PROJECTORS AIR INTAKE AND EXHAUST OPENINGS !LSO INSTALL THE
projector so that cool or hot air from other air conditioning equipment does not flow directly
TOWARD THE PROJECTORS AIR INTAKE OR EXHAUST OPENINGS
s$O NOT INSTALL THE PROJECTOR IN AN ENCLOSED SPACE )F IT IS NECESSARY TO INSTALL IT IN AN ENCLOSED
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at
THE INTAKE OPENING 4HIS MAY CAUSE THE PROJECTORS PROTECTIVE CIRCUIT TO INTERRUPT PROJECTOR OPERA-
tion.
s)F THE PROJECTOR IS PLACED IN A BOX ENSURE THAT THE PROJECTORS INTAKE AND EXHAUST OPENINGS ARE NOT
blocked. Take par ticular care to ensure that hot air from the exhaust openings is not sucked into
the intake openings.
s4O INSTALL AND USE THE PROJECTOR VIA A METHOD THAT DOES NOT USE THE ADJUSTABLE FEET IN A FLOOR
standing installation, fix the projector using the four screw holes for ceiling mounting. ( Screw
diameter: M4, tapping depth inside the set: 7 mm, torque: 1.25 ± 0.2 N·m)
NOTES ON USE