Panasonic ET-PFD510 User manual

ENGLISH
ENGLISH
FRANÇAIS
Thank you for purchasing this Panasonic product.
■Carefully read through these Operating Instructions and the operating instructions of the
projector to ensure safe and proper operation.
■Before using this product, be sure to read “Important Safety Notice” (page 3).
■Please save this manual for future use.
TQZJ436-3
Operating Instructions
Frame
Model No. ET-PFD510

2 - ENGLISH
Contents
Important Safety Notice .................................................................................... 3
Product description........................................................................................... 4
Finished assembly diagram ............................................................................. 4
Projection distances ......................................................................................... 5
Installation.......................................................................................................... 6
Attaching the frame to the projector ................................................................................... 6
Attaching the upper level projector ..................................................................................... 7
Adjusting the upper projector.......................................................................... 8
Dimensions ........................................................................................................ 9
Specications .................................................................................................... 9

ENGLISH - 3
Important Safety Notice
Dear Panasonic Customer:
This instruction booklet provides all the necessary operating information that you might require. We hope it will
help you to get the most performance out of new product, and that you will be pleased with your Panasonic
Projector Frame.
Precautions with regard to safety
■WARNING
Do not loosen or remove the unit screws unnecessarily.
zThe projector may fall down and an injury may result.
Do not install in a location that is not strong enough.
zIf the installation location is not strong enough, the unit may fall down and damage to the projector or an injury
may result.
Do not install the frame in humid or dusty locations or in locations where the frame may
come into contact with oily smoke or steam.
zUsing the projector under such conditions may result in re or electric shock. Also, the oil will cause the plastic
to deteriorate.
Do not allow children to reach the supplied screws and metal ttings.
zThe supplied screws and metal ttings can cause personal injury if swallowed.
zIf swallowed, seek medical advice immediately.
Do not stack any more than two frames on top of each other.
zThe frames may fall down and an injury may result.
Make sure that your footing is safe and secure during installation.
zIf your footing is not secure, you may trip or fall down, and an injury may result.
Mounting and installation must be carried out by two or more persons.
zConsidering the weight of the projector, make sure that mounting and installation are carried out by two or more
persons.
■CAUTION
Do not install the unit in a location that may impede projector ventilation.
zA re may result.
Note
zThis frame cannot be used when the separately sold ET-D75LE90 xed focus lens is attached to the projector.
Model number: ET-PFD510

4 - ENGLISH
Product description
This frame is exclusively for the installation of dual projectors.
■Structural components
Parts name Form (number of parts)
Frame
× 1
Screws and metal ttings
Hexagonal head bolt with washers (M6 × 30)…………… × 6
Hex nuts (M10) ……………………………………………… × 8
Flat washers (M10) ……………………………………… × 16
Bent washers (M10) …………………………………… × 16
Spring washers (M10) …………………………………… × 8
Adjustment nuts (M10) …………………………………… × 4
Hex head bolts (M10 × 140, for vertical xing) ………… × 4
zStore small parts in an appropriate manner, and keep them away from young children.
zThe tightening torque for the screws should be 4 ±0.5 N · m for the M6 screws and 20 ±1 N · m for the M10 screws.
zUse a torque driver, torque wrench or similar tool when tightening the bolts and nuts. Do not use electric
screwdrivers or impact screwdrivers.
Note
zFor dual stack installations, prepare a wrench and other tools in addition to the above.
Finished assembly diagram
Upper projector
Lower projector
ÚExample showing one projector stacked on top of
another projector.
Another separate frame is required when stacking two
frame together.

ENGLISH - 5
Projection distances
The dimensional relationship between the screen and the projector is shown below.
When planning the installation position of the projector, refer to the following gures and table for
reference. The zoom function of the lens allows you to adjust the projection distance. Fine adjust while
checking the projected image.
■Dimensional reationship diagram
L1L
SD
Conter of screen
Screen
B: 430 mm (16-15/16'')
A: 231.5 mm (9-1/8'')
Note
zThis illustration assumes that the projector will be installed so that the projected image lls the screen and is
properly aligned with it.
zThis drawing is not in exact scale.
L Projection distance
L1 Lens protrusion dimension (from front of set to tip of lens)
A From center of lower lens to lower frame installation surface
B From center of upper and lower lens to lower frame
SD Projected image size
Attention
zInstall the projector with a space more than 500 mm (1' 8'') behind it so as not to interfere with projector
ventilation.
zLeave a space of 500 mm (1' 8'') on each side of the projector.
zBefore proceeding with installation, carefully read through the section “Precautions for use” in the projector’s
operating instructions.
Note
zThe projectors depicted in this manual are sample images and may di󰀨er in dimensions from your projector
model.
■Dimensional relationship
For details on lens protrusion dimension (L1) values and calculation formulas for the projection distances (L) of
each projection lens, refer to the "Setting up" section of the operating instructions for your projector.

6 - ENGLISH
Installation
Attaching the frame to the projector
Nut
Hexagonal head
bolt with washer
Frame Bolt
1) Remove attachment plate from frame.
ÚRemove the four hexagonal head bolts
with washers (M6 × 16) used to secure the
attachment plate at the front and back. Remove
the bolt (M6) and nut (M6) attached to the front,
and remove the attachment plate from the frame.
Attention
zThe removed screws are needed for re-installation so
do not lose them.
Attachment plate 2) Place the projector with its base facing upwards on a
soft cloth.
3) Secure the attachment plate to the projector using
the six Hex-head bolt (M6 × 30) provided.
Nut
Hexagonal
head bolt with
washer
Bolt
4) Place the projector with its bottom face down, and
install the frame.
Secure the projector to the frame using the four
hexagonal head bolts with washers (M6 × 16), bolt
(M6) and nut (M6) which were removed in step 1).
Attention
zWhen installing the frame and securing it using the
bolts, take care not to pinch your hand or ngers.
5) Attach the projection lens. (For more information on
attaching, please refer to [Attaching/removing the
projection lens (optional accessory)] in the Operating
Instructions manual of the projector.)

ENGLISH - 7
Installation (continued)
Attaching the upper level projector
Another separate frame is required when stacking two frames together.
Refer to [Attaching the frame to the projector] for the installation procedure of a frame and a projector. (page 6 )
Spring washer
Adjustment feet
Hex nut
Hex nut
Hex head bolt
Upper frame
Lower frame
Flat washers
Adjustment nuts
Flat washer
Flat washer
Spring washer
Bent washer
Flat washer
Bent washer
1) Check the strength and stability of the installation
location. If there are no problems, rst adjust the
adjustment feet of the lower frame and install the
lower projector horizontally.
2) Install the hex head bolts (M10 × 140, for vertical
xing) into the four mounting holes in the lower frame
with the hex nut, spring washer, at washer and bent
washer. Use the hex nuts to secure the lower frame
and the hex head bolts (for vertical xing).
3) Place the adjustment nuts, at washer and bent
washer onto the hex head bolts (for vertical xing).
4) Align the four mounting holes in the upper frame for
the upper projector with the vertical xing hex head
bolts in the lower frame, and place the upper frame
onto the lower frame.
5) Secure the projector using the four adjustment nuts
so that it is horizontal.
6) Place the bent washer, at washer, spring washer
and hex nut (M10) onto the hex head bolts.
7) Use the hex nuts (M10) to secure rmly the upper
frame and the hex head bolts.
Attention
zThe mounting holes in the frames are used only to
attach one frame to the other. Do not use them for
any other purpose.
WARNING:
Mounting and installation must be carried out
by two or more persons.

8 - ENGLISH
Adjusting the upper projector
Follow the steps below to adjust the angle of the upper projector so that the image projected on the screen
matches that of the lower projector whereby the screen size, position, and focus is already adjusted to the screen.
Only the angle of the upper projector is adjustable.
zReferring to the Operating Instructions manual of the projector, project an image on the screen and then use
the zoom and focus functions to adjust its size and focus roughly before adjusting the angle.
zLoosen the securing hex nuts
A
of the upper frame and then adjust the adjustment nuts.
1) Adjusting the vertical angle
Turn the four adjustment bolts to adjust the vertical angle and correct the keystone distortion on the projection screen. Make sure to turn
the right and left adjustment bolts at the front, and the right and left adjustment bolts at the rear, by the same amount.
Spring washer
Movement of the projection screen
and the vertical angle of the upper
projector.
(frame omitted from illustration)
AHex nut
Hex head bolt
Upper Frame
Lower Frame
Flat washer
Flat washer
Flat washer
Projection screen
Flat washer
Adjustment nut
Hex nut
Spring washer
Bent washer
Bent washer
2) Adjusting right-left inclination
Turn the four adjustment bolts to adjust the right-left inclination and correct the rotational distortion on the projection screen.
Make sure to turn the front and rear adjustment bolts on the right, and the front and rear adjustment bolts on the left, by the same
amount.
Spring washer
Spring washer
Movement of the projection screen
and the left-right inclination of the
upper projector.
(frame omitted from illustration)
A
Hex nut
Hex head bolt
Upper frame
Lower frame
Flat washer
Flat washer
Flat washer
Flat washer
Projection screen
Adjustment nut
Hex nut
Bent washer
Bent washer
3) Repeat the steps 1), 2) to make ne adjustments.
4) When adjustment is complete, tighten the hex nuts to prevent the projector from
A
shifting.

ENGLISH - 9
Dimensions
(Units : mm)
932 (36-11/16'')
582 (22-29/32'') 681 (26-13/16'')
175
(6-7/8'')
712 (28-1/32'')
376.5
(14-13/16'')
32
(1-1/4'')
Front
Specications
Adjustable range Vertical angle correction : ± 1.5 °
Left and right inclination adjustment : ± 1.5 °
Assembled external dimensions
Width : 712 mm (28-1/32")
Height : 408.5 mm (16-3/32") (with legs at shortest position)
Depth : 932 mm (36-11/16")
Weight (excluding the projector) Approx. 19.4 kg (42.8 lbs.)

SS0512NK3048 -PJ
Printed in Japan
Attention
zDispose of the packaging materials properly after taking the product out of it.
■Disposal
When discarding this product, please contact your local authorities or dealer and ask for the correct method of
disposal.
Panasonic Corporation
Web Site : https://panasonic.net/cns/projector/
© Panasonic Corporation 2012