Paradise Datacom 205486 REV F User manual

Compact Outdoor
Solid State Power Amplifier
Operations Manual
208495 REV B ECO 16449 08/30/2011
Teledyne Paradise Datacom LLC Phone: [phone]
328 Innovation Blvd., Suite 100 Fax: [phone]
State College, PA 16803 USA Web: www.paradisedata.com
Email: [email protected]

2 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
Teledyne Paradise Datacom LLC, a Teledyne Telecommunications company, is a single source for high power
solid state amplifiers (SSPAs), Low Noise Amplifiers (LNAs), Block Up Converters (BUCs), and Modem
products. Operating out of two primary locations, Witham, United Kingdom, and State College, PA, USA,
Teledyne Paradise Datacom has a 20 year history of providing innovative solutions to enable satellite uplinks,
battlefield communications, and cellular backhaul.
Teledyne Paradise Datacom LLC Teledyne Paradise Datacom Ltd.
328 Innovation Blvd., Suite 100 2-3 The Matchyns, London Road, Rivenhall End
State College, PA 16803 USA Witham, Essex CM8 3HA United Kingdom
[phone] (switchboard) [phone]
[phone] (fax) [phone] (fax)
Information in this document is subject to change without notice. The latest revision of this document may be
downloaded from the company web site: http://www.paradisedata.com.
No part of this document may be reproduced or transmitted in any form without the written permission of
Teledyne Paradise Datacom LLC.
All rights are reserved in this document, which is property of Teledyne Paradise Datacom LLC. This document
contains proprietary information and is supplied on the express condition that it may not be disclosed,
reproduced or transmitted in any form without the written permission of Teledyne Paradise Datacom LLC.
All other company names and product names in this document are property of the respective
companies.
© 2011 Teledyne Paradise Datacom LLC
Printed in the USA

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 3
Section 1: General Information ........................................................................................ 11
1.0 Introduction ......................................................................................................... 11
1.1 Description .......................................................................................................... 11
1.2 Specifications...................................................................................................... 11
1.3 Equipment Supplied............................................................................................ 11
1.4 Safety Considerations......................................................................................... 12
1.4.1 High Voltage Hazards ...................................................................................... 12
1.4.2 RF Transmission Hazards ............................................................................... 12
Section 2: Installation........................................................................................................ 13
2.0 Introduction ......................................................................................................... 13
2.1 Inspection ........................................................................................................... 13
2.2 Prime Power Connection [MS3102E20-3P] ........................................................ 13
2.3 DC Input Option [MS3102E-20-29P]................................................................... 15
2.4 Summary Alarm Indicator ................................................................................... 15
2.5 Cable Connections.............................................................................................. 15
2.5.1 RF Input (J1) [N-type (F)]................................................................................. 16
2.5.2 Monitor & Control Connector (J4) [MS3112E18-32S] ...................................... 16
2.5.3 Link Port (J5) [MS3112E10-6S] ....................................................................... 16
2.5.4 Switch Port (J6) [MS3112E10-6S] ................................................................... 17
2.5.5 RF Output (J2) ................................................................................................. 17
2.5.6 RF Output Sample Port (J3) [N-type (F)] ......................................................... 18
2.5.7 AC Input (J7) .................................................................................................. 18
2.5.8 15 VDC Output Port (J8) [MS3112E10-6S]...................................................... 18
2.5.9 Chassis Ground Terminal ................................................................................ 18
2.6 Airflow ................................................................................................................. 19
2.7 Unit Weights........................................................................................................ 19
2.8 Compact Outdoor Mounting Kit Installation......................................................... 21
2.8.1 Safety Considerations...................................................................................... 21
2.8.2 Inspection......................................................................................................... 21
2.8.3 Installation........................................................................................................ 21
Section 3: Quick Start & Operation.................................................................................. 25
3.0 Introduction ......................................................................................................... 25
3.0.1 Remote Communications Connections............................................................ 25
3.0.2 Legacy Compact Outdoor SSPAs.................................................................... 26
3.0.3 Compact Outdoor SSPAs in Legacy Systems ................................................. 27
3.1 Port J4 Pin-Outs.................................................................................................. 28
3.2 Quick Start Cables .............................................................................................. 30
3.3 Quick Start Connections ..................................................................................... 31
3.3.1 Set PC Configuration ....................................................................................... 31
3.3.2 Quick Start Ethernet Connection...................................................................... 31
3.3.3 Quick Start RS-232 Connection ....................................................................... 32
3.4 Universal M&C Operation ................................................................................... 33
3.4.1 Universal M&C Status Window ........................................................................ 34
Table of Contents

4 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
3.4.1.1 Signal Indicators............................................................................................ 34
3.4.1.2 Fault Status Indicators .................................................................................. 35
3.4.1.3 Voltage, Current and Temperature Display................................................... 36
3.4.1.4 Gain Adjustment............................................................................................ 36
3.4.1.5 RF Power Indicator ....................................................................................... 36
3.4.2 Universal M&C Settings Window...................................................................... 37
3.4.2.1 Power Up Settings ........................................................................................ 37
3.4.3 IP Setup Window.............................................................................................. 39
3.4.4 Universal M&C Preferences............................................................................. 40
3.5 Web-based M&C................................................................................................. 41
3.5.1 Navigating the Web M&C................................................................................. 42
Section 4: Operation.......................................................................................................... 47
4.0 Introduction ......................................................................................................... 47
4.1 AC / DC Converter .............................................................................................. 48
4.2 DC / DC Converter .............................................................................................. 48
4.3 Solid State Power Amplifier Module .................................................................... 48
4.3.1 RF Input (J1) .................................................................................................... 48
4.3.2 RF Output (J2) ................................................................................................. 49
4.3.3 Amplifier Enable (Mute/Unmute) (J4) ............................................................... 49
4.3.4 Alarms (J4)....................................................................................................... 49
4.3.4.1 Summary Alarm (J4) Form C Contacts ......................................................... 49
4.3.4.2 Auxiliary Alarm (J4) Form C Contacts ........................................................... 49
4.3.4.3 Open Collector Alarm Outputs (J4) ............................................................... 50
4.3.5 RF Power Detector (J4) ................................................................................... 50
4.3.6 RF Output Sample (J3) .................................................................................... 50
4.3.7 Gain Adjust Input (J4) ...................................................................................... 50
4.3.8 Serial I/O Control (J4) ...................................................................................... 51
4.4 Fan Boost Converter ........................................................................................... 51
4.5 Cooling System................................................................................................... 51
Section 5: L Band Operation............................................................................................. 55
5.0 Block Up Converter Overview ............................................................................. 55
5.1 ZBUC Features ................................................................................................... 56
5.2 ZBUC Converter Theory of Operation................................................................. 57
5.3 Smart Reference Technology ............................................................................. 57
5.4 ZBUC FSK Monitor and Control.......................................................................... 58
5.5 Typical System Configuration ............................................................................. 59
5.6 IFL Cable Considerations.................................................................................... 59
Section 6: Fiber-Optic Option ........................................................................................... 61
6.0 Fiber-Optic Option............................................................................................... 61
6.0.1 RCPF-1000 Fiber Optic Controller ................................................................... 61
6.0.2 External L-Band to Fiber Interface ................................................................... 62

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 5
Section 7: Performance Tests .......................................................................................... 65
7.0 Introduction ......................................................................................................... 65
7.1 Standard tests..................................................................................................... 65
7.1.1 Swept Gain ..................................................................................................... 65
7.1.2 Spurious.......................................................................................................... 66
7.1.3 Input Return Loss............................................................................................ 66
7.1.4 Output Return Loss......................................................................................... 66
7.1.5 Intermodulation Distortion ............................................................................... 67
7.1.6 Power Requirements ...................................................................................... 67
7.1.7 Earth Ground .................................................................................................. 68
7.1.8 Sample Port .................................................................................................. 68
7.1.9 P1dB and Psat ............................................................................................... 68
7.1.10 I/O Test ......................................................................................................... 68
7.1.11 Ethernet (if equipped) ................................................................................... 68
7.2 Tests for units with integrated zBUC................................................................... 69
7.2.1 Reference Lock................................................................................................ 69
7.2.2 FSK.................................................................................................................. 69
7.2.3 Phase Noise..................................................................................................... 69
7.2.4 Microphonics.................................................................................................... 69
7.3 Optional Tests..................................................................................................... 70
7.3.1 Noise Figure..................................................................................................... 70
7.3.2 Group Delay..................................................................................................... 70
7.3.3 AM/PM ............................................................................................................. 70
7.3.4 Noise Power..................................................................................................... 70
7.3.5 Harmonics........................................................................................................ 70
Section 8: Maintenance & Troubleshooting .................................................................... 71
8.0 Introduction ......................................................................................................... 71
8.1 Cooling System Maintenance ............................................................................. 71
8.2 Fan Removal and Heatsink Cleaning.................................................................. 71
8.2.1 Fan Replacement............................................................................................. 72
8.3 Troubleshooting guide ........................................................................................ 72
8.3.1 Unit doesn’t power up ...................................................................................... 72
8.3.2 Unit powers on, LED lamp glows red ............................................................... 72
8.3.3 SSPA unit powers up, LED lamp glows green, but no RF output is present .... 73
8.3.4 Cannot connect to SSPA through remote control interface.............................. 73
8.3.5 The FSK link between a modem and the SSPB unit is not working ................. 74
Section 9: Redundant System Operation ........................................................................ 75
9.0 Redundant System Concepts ............................................................................. 75
9.1 Compact Outdoor Amplifier in 1:1 Redundancy.................................................. 77
9.1.1 Hardware Setup ............................................................................................... 78
9.1.2 Software Setup ................................................................................................ 79
9.1.2.1 Stand-Alone 1:1 Redundant System............................................................. 79
9.1.2.2 PC Control using RS232 and Paradise M&C Software................................ 82
9.1.2.3 PC Control using RS-485 and Paradise M&C Software............................... 87
9.2 1:2 Redundant Systems...................................................................................... 89
9.3 1:2 Redundant Systems with L-Band Input......................................................... 92

6 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
Section 10: Fixed Phase Combined Redundant Systems .............................................. 97
10.0 Phase Combining Overview.............................................................................. 97
10.1 1:1 Fixed Phase Combined System Components............................................. 99
10.1.1 Signal Box Assembly ..................................................................................... 99
10.2 1:1 Fixed Phase Combined System Operation with the FPRC-1100 .............. 101
10.3 1:1 Fixed Phase Combined System with L-Band Input ................................... 102
10.3.1 1:1 Fixed Phase Combined System with L-Band Input Components ........... 103
10.3.2 Signal Box Assembly ................................................................................... 103
10.3.3 Redundant BUC Operation .......................................................................... 103
10.3.4 Adjusting the Phase Combining .................................................................. 103
10.4 1:2 Fixed Phase Combined Systems .............................................................. 105
10.4.1 1:2 Fixed Phase Combined System Components........................................ 106
10.4.2 Signal Box Assembly ................................................................................... 106
10.5 1:2 Fixed Phase Combined System Operation with FPRC-1200 .................... 108
10.5.1 Phase Adjustment ........................................................................................ 109
Section 11: Remote Control Interface............................................................................ 111
11.0 Serial Protocol Overview................................................................................. 111
11.1 Serial communication...................................................................................... 113
11.1.1 Header Packet ............................................................................................. 113
11.1.1.1 Frame Sync Word ..................................................................................... 113
11.1.1.2 Destination Address .................................................................................. 113
11.1.1.3 Source Address......................................................................................... 114
11.1.2 Data Packet ................................................................................................. 114
11.1.2.1 Protocol ID ................................................................................................ 114
11.1.2.2 Request ID ................................................................................................ 114
11.1.2.3 Command ................................................................................................. 114
11.1.2.4 Data Tag ................................................................................................... 115
11.1.2.5 Data Address / Error Status / Local Port Frame Length ............................ 116
11.1.2.6 Data Length............................................................................................... 116
11.2.7 Data Field..................................................................................................... 116
11.1.3 Trailer Packet............................................................................................... 117
11.1.3.1 Frame Check............................................................................................. 117
11.1.4 Timing issues ............................................................................................... 117
11.1.5 Serial Communications Protocol .................................................................. 118
11.1.6 Serial Communication Examples ................................................................. 122
11.2 Ethernet Interface............................................................................................ 127
11.2.1 Overview ...................................................................................................... 127
11.2.2 IPNet Interface ............................................................................................. 127
11.2.2.1 General Concept ....................................................................................... 127
11.2.2.2 Setting IPNet interface .............................................................................. 129
11.2.2.3 Troubleshooting IP connectivity ................................................................ 129
11.2.4 SNMP interface ............................................................................................ 130
11.2.4.1 SNMP MIB tree ......................................................................................... 131
11.2.4.2 Description of MIB entities ........................................................................ 132
11.3 M&C via SNMP ............................................................................................... 136
11.3.1 Connecting to a MIB browser....................................................................... 137

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 7
Appendix A: Quick Start Cable....................................................................................... 139
Appendix B: Alternate System Configurations............................................................. 141
Appendix C: Documentation .......................................................................................... 143
Figures
Figure 2-1: Outline, Compact Outdoor Solid State Amplifier..................................... 15
Figure 2-2: Input Side, Compact Outdoor Amplifier .................................................. 16
Figure 2-3: RF Output Side of C Band Compact Outdoor SSPA .............................. 17
Figure 2-4: Bottom View, Compact Outdoor Amplifier ............................................. 18
Figure 2-5: Improper mounting ................................................................................. 19
Figure 2-6: Bolt Mounting Bracket to Unit ................................................................. 22
Figure 2-7: Unit Ready for Boom Installation ............................................................ 22
Figure 2-8: CO Mount Completed............................................................................. 23
Figure 3-1: J4 Connections for Ethernet Communications........................................ 25
Figure 3-2: J4 Connections for RS-485 Communications ......................................... 26
Figure 3-3: J4 Connections for RS-232 Communications ......................................... 26
Figure 3-4: J4 Connections for RS-485 Communications for S/N <300,000 ............ 26
Figure 3-5: J4 Connections for RS-232 Communications for S/N <300,000 ............ 27
Figure 3-6: J4 Connections for RS-485 Comms using older M&C cables ................ 27
Figure 3-7: Ethernet Quick Start Cable, 207755 ....................................................... 30
Figure 3-8: RS-232 Quick Start Cable, 207998 ........................................................ 30
Figure 3-9: Universal M&C Add Unit menu ............................................................... 33
Figure 3-10: Add Compact Outdoor SSPA window, via Serial or Internet ................ 33
Figure 3-11: Universal M&C Status Window............................................................. 34
Figure 3-12: Fault Indicators ..................................................................................... 35
Figure 3-13: Universal M&C, Settings....................................................................... 37
Figure 3-14: Spare Fault Wizard............................................................................... 38
Figure 3-15: Universal M&C, IP Setup ...................................................................... 39
Figure 3-16: Preferences Window............................................................................. 40
Figure 3-17: Example, Log entry............................................................................... 40
Figure 3-18: Enter IP address for Compact Outdoor SSPA (default is 192.168.0.9) 41
Figure 3-19: M&C Applet loading into browser window............................................. 41
Figure 3-20: Enter password (default is “paradise”).................................................. 42
Figure 3-21: Status and Faults window descriptions................................................. 42
Figure 3-22: Communication Settings window descriptions...................................... 43
Figure 3-23: General Settings window descriptions.................................................. 44
Figure 3-24: Fault Settings window descriptions....................................................... 45
Figure 4-1: Block Diagram, Compact Outdoor Amplifier ........................................... 47
Figure 4-2: Schematic, Non-Ethernet Compact Outdoor SSPA................................ 52
Figure 4-3: Schematic, Ethernet capable Compact Outdoor SSPA .......................... 53
Figure 4-4: Schematic, 48 VDC Ethernet Compact Outdoor SSPA .......................... 54
Figure 5-1: Configuration Matrix, Compact Outdoor SSPA, BUC Options ................ 55
Figure 5-2: Compact Outdoor Block Diagram of BUC / SSPA System ..................... 56
Figure 5-3: Compact Outdoor SSPB with PD25 Evolution Modem........................... 59
Figure 6-1: RCPF-1000 front, rear panels................................................................. 61
Figure 6-2: Outline Drawing, External L-Band to fiber interface................................ 62
Figure 6-3: Block Diagram, Compact Outdoor with external fiber transceiver........... 63
Figure 6-4: System example, SSPA with External Fiber to L-Band Converter.......... 64
Figure 7-1: Spurious and Gain Data ......................................................................... 65

8 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
Figure 7-2: Return Loss, Intermodulation and Phase Noise Data ............................. 66
Figure 7-3: M&C, Output Power, Ground, Phase Lock and Misc. Data .................... 67
Figure 8-1: Fan Removal from Amplifier Assembly................................................... 71
Figure 9-1: Standard 1:1 Redundant System with coaxial and waveguide switches. 75
Figure 9-2: 1:1 Redundant System with input splitter substituted for input switch..... 75
Figure 9-3: 1:1 Redundant System with L Band input............................................... 76
Figure 9-4: Typical 1:1 Redundant System Outline................................................... 77
Figure 9-5: 1:1 Redundant System with Link Cable and Switch Cable installed ....... 78
Figure 9-6: 1:1 System with RS-232 Communication to each Amplifier.................... 79
Figure 9-7: M&C Program "SSPA Settings" window ................................................. 80
Figure 9-8: Adding a SSPA Monitor and Control Window ......................................... 82
Figure 9-9: Add New Compact Outdoor SSPA window............................................. 83
Figure 9-10: Individual SSPA Operation Window...................................................... 83
Figure 9-11: Paradise Datacom Universal M&C, Add Unit Menu Tree...................... 84
Figure 9-12: Add 1:1 Redundant System Window .................................................... 84
Figure 9-13: Redundant Control Panel showing configured 1:1 Redundant System 85
Figure 9-14: Dialog window, Affirm mute of on-line amplifier .................................... 85
Figure 9-15: Control Panel showing Unit 1 faulted and signal routed to Unit 2 ......... 86
Figure 9-16: Unit1 Status panel showing Summary and Temperature Faults ........... 86
Figure 9-17: 1:1 Redundant System with RS-485 Full Duplex Communication ........ 87
Figure 9-18: 1:1 Redundant System with RS-485 Half Duplex Communication........ 88
Figure 9-19: 1:2 Redundant System ......................................................................... 89
Figure 9-20: 1:2 Redundant System Block Diagram ................................................. 89
Figure 9-21: Outline, 1:2 Redundant System ............................................................ 90
Figure 9-22: Schematic, 1:2 Redundant System....................................................... 91
Figure 9-23: 1:2 System with L Band Input and Internal Reference BUCs................ 92
Figure 9-24: 1:2 System showing absence of reference to stand-by BUC ................ 93
Figure 9-25: 1:2 Redundant System with (3) 10MHz inputs through input switches . 94
Figure 9-26: 1:2 Redundant System with Reference Combiner Assembly................ 95
Figure 10-1: Phase Combined Amplifier System ...................................................... 97
Figure 10-2: 1:1 Fixed Phase Combined System with FPRC-1100 controller........... 98
Figure 10-3: Outline, 1:1 Fixed Phase Combined System ...................................... 100
Figure 10-4: FPRC-1100 Phase Combined System Controller ............................... 101
Figure 10-5: 1:1 Phase Combined System with HPA control of BUC redundancy.. 102
Figure 10-6: Connect to coupler.............................................................................. 103
Figure 10-7: Outline, 1:1 Fixed Phase Combined System with L-Band Input.......... 104
Figure 10-8: Phase adjuster.................................................................................... 105
Figure 10-9: Block Diagram, 1:2 Fixed Phase Combined System .......................... 105
Figure 10-10: Outline, 1:2 Fixed Phase Combined System, C-Band ...................... 107
Figure 10-11: FPRC-1200 1:2 Phase Combined Redundant Controller ................. 108
Figure 10-12: HPA #1 & HPA #3 on line with HPA #2 on standby .......................... 108
Figure 11-1: Compact Outdoor remote control interface stack................................ 111
Figure 11-2: Basic Communication Packet ............................................................. 113
Figure 11-3: Header Sub-Packet ............................................................................ 113
Figure 11-4: Data Sub-Packet................................................................................. 114
Figure 11-5: Trailer Sub-Packet .............................................................................. 117
Figure 11-6: UDP Redirect Frame Example............................................................ 128
Figure 11-7: Universal M&C, IP Setup tab .............................................................. 136
Figure 11-8: Universal M&C, Settings tab ............................................................... 136

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 9
Figure 11-9: GetIF Application Parameters Tab ..................................................... 137
Figure 11-10: Getif MBrowser window, with update data in output data box .......... 137
Figure A-1: Ethernet Quick Start Cable................................................................... 139
Figure A-2: RS-232 Quick Start Cable, 207998 ...................................................... 140
Figure B-1: Mixed Redundant System using New and Old CO Amplifiers .............. 141
Figure B-2: Redundant System using RCP2-1100 Controller ................................. 142
Tables
Table 2-1: AC Line Input Connector.......................................................................... 13
Table 2-2: Compact Outdoor Amplifier Prime Power Summary............................... 14
Table 2-3: DC Input Connector, MS3102E-20-29P.................................................. 15
Table 2-4: Link Port (J5) Pin-Outs............................................................................. 16
Table 2-5 Switch Port (J6) Pin-Outs.......................................................................... 17
Table 2-6: +15 VDC Output Port (J8) Pin-Outs......................................................... 18
Table 2-7: Compact Outdoor SSPA Weights ............................................................ 20
Table 2-8: Mounting Kit Parts List............................................................................. 21
Table 3-1: Monitor & Control Connector (J4) Pin-Out (Ethernet capable)................. 28
Table 3-2: Monitor & Control Connector (J4) Pin-Out (Non-Ethernet)....................... 29
Table 5-1: ZBUC Converter Frequency Specifications ............................................. 56
Table 5-2: ZBUC RF output phase noise specification ............................................. 57
Table 5-3: Common Coaxial Cable Characteristics ................................................. 59
Table 9-1: Returning Amp 2 to Stand-by Mode After Fault on Thread 1 or 3............ 95
Table 11-1: Interface Selection ............................................................................... 112
Table 11-2: Command Byte Values ........................................................................ 115
Table 11-3: Data Tag Byte Values.......................................................................... 115
Table 11-4: Error Status Bytes................................................................................ 116
Table 11-5: Request Frame Structure..................................................................... 118
Table 11-6: Response Frame Structure.................................................................. 118
Table 11-7: System Settings Data Values .............................................................. 119
Table 11-8: System Threshold Data Values ........................................................... 120
Table 11-9: System Condition Addressing............................................................. 121
Table 11-10: OSI Model for Compact Outdoor SSPA Ethernet IP Interface ........... 128
Table 11-11: Detailed Settings for CO SSPA mode (Device Type=2) .................... 133
Table 11-12: Detailed Thresholds ........................................................................... 135
Table 11-13: Detailed Conditions............................................................................ 135
Table A-1: Wiring Chart, Ethernet Quick Start Cable .............................................. 139
Table A-2: Wiring Chart, RS-232 Quick Start Cable ............................................... 140

10 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
THIS PAGE INTENTIONALLY LEFT BLANK

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 11
1.0 Introduction
This section provides the general information for the Teledyne Paradise Datacom LLC line of
Compact Outdoor Solid State Power Amplifiers. The Compact Outdoor SSPA has been
designed and manufactured to be an extremely robust and reliable amplifier. It is well suited
for harsh outdoor environments.
1.1 Description
The Compact Outdoor SSPA is a one-piece integrated Satcom amplifier system. It includes
the AC/DC power supply, microwave amplifier module, microprocessor based monitor and
control circuitry, and an efficient thermal management system.
The reduced size and weight of this amplifier system allow it to be used in a wide variety of
installations; many of which historically precluded the use of Solid State power amplifiers.
This amplifier is ideal for mounting on the boom of small antennas or anywhere that size and
weight are a major concern.
Features include:
• Compact Size: 10.0 in x 19.5 in x 6.50 in. (254 mm x 495 mm x 165 mm)
• Very light weight: Base units weigh as little as 36 lb. (16.4 kg)
• Auto-Sensing Power Factor Corrected Power Supply
• RF Gain Adjustment: 55 dB to 75 dB minimum with 0.1 dB resolution
• Output Power Detection
• Output Power Sample Port
• Internal 1:1 Redundant Capability
• Optional L-Band Input Capability
• Serial (RS-232 / RS-485), Ethernet or Parallel Monitor & Control Circuitry
• Windows Monitor & Control Software
1.2 Specifications
Refer to Appendix C for full specifications of the Compact Outdoor SSPA.
1.3 Equipment Supplied
The following equipment is supplied with each unit:
• The Compact Outdoor Amplifier Assembly;
• Prime power mating connector: AC - MS3106E20-3S; DC - MS3106F20-29S
• Quick Start Serial (Ethernet) Communication Cable, L207755-2, -OR-
Quick Start Serial (RS-232 / RS-485) Communication Cable, L207998-2
Section 1: General Information

12 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
• Product Guide CD with SSPA Monitor & Control Software
• M&C (J4) Mating Connector, MS3116F18-32P
• Waveguide gaskets (dependent on frequency band)
• Sealing tape (87F730)
1.4 Safety Considerations
Potential safety hazards exist unless proper precautions are observed when working with this
unit. To ensure safe operation, the user must follow the information, cautions, and warnings
provided in this manual as well as the warning labels placed on the unit itself.
1.4.1 High Voltage Hazards
Only qualified service personnel should service the internal electronic
circuitry of the Compact Outdoor Amplifier. High DC voltages (300 VDC) are
present in the power supply section of the amplifier. Care must be taken
when working with devices that operate at this high voltage levels. It is
recommended to never work on the unit or supply prime AC power to the unit
while the cover is removed.
1.4.2 RF Transmission Hazards
RF transmissions at high power levels may cause eyesight damage and skin
burns. Prolonged exposure to high levels of RF energy has been linked to a
variety of health issues. Please use the following precautions with high levels
of RF power.
• Always terminate the RF input and output connector prior to applying prime AC
input power.
• Never look directly into the RF output waveguide
• Maintain a suitable distance from the source of the transmission such that the power
density is below recommended guidelines in ANSI/IEEE C95.1. The power density
specified in ANSI/IEEE C95.1-1992 is 10 mW/cm2. These requirements adhere to OSHA
Standard 1910.97.
• When a safe distance is not practical, RF shielding should be used to achieve the
recommended power density levels.

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 13
2.0 Introduction
This section provides information for the initial inspection, installation, external connections,
and shipment of the Compact Outdoor SSPA unit.
2.1 Inspection
When the unit is received, an initial inspection should be completed. First ensure that the
shipping container is not damaged. If it is, have a representative from the shipping company
present when the container is opened. Perform a visual inspection of the Compact Outdoor
Amplifier to make sure that all items on the packing list are enclosed. If any damage has
occurred or if items are missing, contact:
Teledyne Paradise Datacom LLC
328 Innovation Park, Suite 100
State College, PA 16803
Phone: [phone]
Fax: [phone]
2.2 Prime Power Connection [MS3102E20-3P]
The Prime power connector is a 3-pin circular connector, J7. The power supplies provide
universal AC input by using auto-sensing power supplies. The AC input can operate over a
range of 90-265 VAC, at 47 to 63 Hz. The power supply is also power factor corrected,
enabling the unit to achieve a power factor greater than 0.93.
The highest output power levels, >70 W @ Ku-Band and >100 W @ C-Band should be
powered only from a 180–265 VAC source. This will keep AC line currents to safe operating
levels for the internal EMI filter and associated circuitry. The AC Line input connector
configuration is given in Table 2-1. The prime power vs. RF output power is summarized in
Table 2-2. An option for 110 VAC prime power is available for the higher-powered units.
WARNING! Always terminate the RF input and output connectors prior to
applying prime AC input power!
Pin # on J7 Connection
A L1
B GND
C L2/N
Table 2-1: AC Line Input Connector
Section 2: Installation

14 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
Band Model RF Output Power AC Input Voltage AC Input Power
Psat / P1dB Operating Range Maximum
C-Band
5.850 - 6.425 GHz
HPAC2030ACXXXXX 45.0/44.8 dBm 90 – 265 vac 250 W
HPAC2040ACXXXXX 46.0/45.8 dBm 90 – 265 vac 300 W
HPAC2050ACXXXXX 47.0/46.8 dBm 90 – 265 vac 400 W
HPAC2075ACXXXXX 48.8/48.5 dBm 90 – 265 vac 450 W
HPAC2100ACXXXXX 50.0/49.5 dBm 90 – 265 vac 700 W
HPAC2140ACXXXXX 51.5/51.0 dBm 180 – 265 vac* 850 W
HPAC2200ACXXXXX 53.0/52.3 dBm 180 – 265 vac* 1000 W
HPAC2250ACXXXXX 53.9/53.0 dBm 180 – 265 vac* 1300 W
HPAC2300ACXXXXX 54.7/54.0 dBm 180 – 265 vac* 1700 W
Ku-Band
14.000 - 14.500 GHz
HPAK2010ACXXXXX 40.0/39.0 dBm 90 – 265 vac 220 W
HPAK2020ACXXXXX 43.0/42.0 dBm 90 – 265 vac 250 W
HPAK2025ACXXXXX 44.0/43.0 dBm 90 – 265 vac 320 W
HPAK2035ACXXXXX 45.5/44.5 dBm 90 – 265 vac 350 W
HPAK2040ACXXXXX 46.0/45.0 dBm 90 – 265 vac 550 W
HPAK2050ACXXXXX 47.0/46.0 dBm 90 – 265 vac 600 W
HPAK2070ACXXXXX 48.5/47.5 dBm 90 – 265 vac 650 W
HPAK2100ACXXXXX 50.0/49.0 dBm 180 – 265 vac* 1000 W
HPAK2125ACXXXXX 51.0/50.0 dBm 180 – 265 vac* 1150 W
HPAKG200ACXXXXX◊56.0 dBm (P3dB) 90 – 265 vac 2000 W
X-Band
7.900 - 8.400 GHz
HPAX2060ACXXXXX 47.5/47.3 dBm 90 – 265 vac 650 W
HPAX2075ACXXXXX 48.8/48.3 dBm 90 – 265 vac 700 W
HPAX2100ACXXXXX 50.0/49.5 dBm 90 – 265 vac 750 W
HPAX2140ACXXXXX 51.4/50.8 dBm 180 – 265 vac 1225 W
HPAX2200ACXXXXX 53.0/51.8 dBm 180 – 265 vac* 1370 W
HPAX2250ACXXXXX 54.0/53.0 dBm 180 – 265 vac* 1550 W
S-Band
2.020 - 2.120 GHz
(unless otherwise indicated)
HPAS2050ACXXXXX 47.5/47.0 dBm 90 – 265 vac 425 W
HPAS2100ACXXXXX 50.5/50.0 dBm 90 – 265 vac 650 W
HPAS2200ACXXXXX** 53.5/53.0 dBm 180 – 265 vac* 1000 W
HPAS2200ACXXXXX*** 53.0/52.5 dBm 180 – 265 vac* 1000 W
HPAS2300ACXXXXX** 55.0/54.5 dBm 180 – 265 vac* 1600 W
HPAS2300ACXXXXX*** 54.4/54.0 dBm 180 – 265 vac* 1600 W
HPAS2050BCXXXXX@47.5/47.0 dBm 90 – 265 vac 425 W
HPAS2100BCXXXXX@50.5/50.0 dBm 90 – 265 vac 650 W
HPAS2200BCXXXXX@53.5/53.0 dBm 180 – 265 vac* 1000 W
HPAS2300BCXXXXX@55.0/54.5 dBm 180 – 265 vac* 1600 W
HPAKA040ACXXXXX 43.0/— dBm 90 – 265 vac 280 W
HPAKA080ACXXXXX 46.0/— dBm 90 – 265 vac 520 W
* Optional 110 vac operation available; ** 2.020 - 2.090 GHz; *** 2.095 - 2.120 GHz @ 2.200 - 2.300 GHz ◊GaN module (P3dB only)
Ka-
Band
30.0 -
31.0
GHz
Table 2-2: Compact Outdoor Amplifier Prime Power Summary

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 15
2.3 DC Input Option [MS3102E-20-29P]
The Compact Outdoor Amplifier can also be configured with a DC Input Voltage power
supply. The DC Input Voltage can range from 42-60 VDC. When using a DC input voltage
the input power connector, J7, is configured per Table 2-3.
2.4 Summary Alarm Indicator
A summary alarm indicator LED is located on the input side of the amplifier. When the SSPA
is online, this indicator illuminates GREEN. When in a fault condition, it illuminates RED.
2.5 Cable Connections
Figure 2-1 shows the overall dimensioned outline of the Compact Outdoor Amplifier. The
connector locations can be found in Figures 2-2 through 2-4.
Pin # on J7 Connection
B +48 V
C +48 V
D +48 V
K -48 V
Connection
-48 V
-48 V
GND
Pin # on J7
L
M
N
Table 2-3: DC Input Connector, MS3102E-20-29P
Figure 2-1: Outline, Compact Outdoor Solid State Amplifier
SWITCH
M & C
J4
STATUS
SSPA
RF IN
J6
J1
J5
LINK
AUX POWER
J8
MODEL:XX XXXXXXXXXX
P/N:LXXXXXX-X
S/N: XXXX
SAMPLE
J3
J7
RF OUT
J2
AC IN
RF OUT
J2

16 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
2.5.1 RF Input (J1) [N-type (F)]
The RF Input connector is a type N female connector. Nominal RF input levels are approxi-
mately -28 dBm depending on the output power level of the unit. The maximum allowable RF
input signal should be limited to +15 dBm.
Figure 2-2 shows the input side of the Compact Outdoor Amplifier. This side contains the RF
input (J1), M&C input (J4), and the Interface connections (J5, J6).
2.5.2 Monitor & Control Connector (J4) [MS3112E18-32S]
The M&C, Monitor and Control, connector is the primary input for controlling the amplifier and
monitoring fault conditions. It is a 32-pin circular connector, MS3112E18-32S. It requires a
mating connector, MS3116F18-32P, which is supplied with the unit. The pin-out for this
connector is described in Section 3, Table 3-2.
2.5.3 Link Port (J5) [MS3112E10-6S]
The interface connector is used to connect between two Compact Outdoor Amplifiers when
used in a 1:1 redundant system. It is a 6 pin circular connector, MS3112E10-6S. It requires a
mating connector, MS3116F10-6P. A link cable is provided with a 1:1 Redundancy Kit which
can be purchased separately. See Table 2-4.
Table 2-4: Link Port (J5) Pin-Outs
Pin # on J5 Connection Pin # on J5 Connection
A LINK OUT D N/C
B LINK IN E N/C
C N/C F GND
Figure 2-2: Input Side, Compact Outdoor Amplifier
SWITCH
M & C
J4
STATUS
SSPA
RF IN
J6
J1
J5
LINK

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 17
2.5.4 Switch Port (J6) [MS3112E10-6S]
When used in a 1:1 redundant system, the waveguide switch must be connected to the switch
port of each amplifier (MS3112E10-6S). See Table 2-5. It mates with MS3116F10-6P.
2.5.5 RF Output (J2)
The RF Output is brought out through waveguide in the Compact Outdoor Amplifier. Figure
2-3 shows the output of a C-Band Compact Outdoor Amplifier. The Ku-Band amplifiers have a
WR75 grooved flange, while the C-Band and X-Band amplifiers have CPR style grooved
flanges (CPRG-137 for C-Band; CPRG-112 for X-Band). Ka-Band amplifiers utilize a WR28
grooved flange. S-Band units are fitted with Type N (F) connectors at the RF Output.
Table 2-5 Switch Port (J6) Pin-Outs
Pin # on J6 Connection Pin # on J6 Connection
A N/C D N/C
B N/C E POS 2
C +28 VDC F POS 1
Figure 2-3: RF Output Side of C Band Compact Outdoor SSPA
RF OUT
J2
Warning! Radiation hazard when un-terminated. Do not
operate the SSPA without terminating the RF Output
(J2). Do not look directly into the RF Output waveguide.

18 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
2.5.6 RF Output Sample Port (J3) [N-type (F)]
The RF Output Sample port, J3, is located on the bottom of the amplifier as shown in Figure
2-4. This connector provides a -40 dBc sample of the amplifier’s output signal. It is a N-type
female connector.
2.5.7 AC Input (J7)
The AC Input connector, J7, is located on the bottom side of the Compact Outdoor Amplifier
package (see Figure 2-4). There are also two alternate placements for this connector on the
RF Output end of the amplifier as shown in Figure 2-3. This connector is a 3-pin circular
connector, MS3102E20-3P. The mating connector (MS3106F20-3S) is shipped with the unit.
The pin out for this connector is given in Table 2-1.
2.5.8 15 VDC Output Port (J8) [MS3112E10-6S]
The 15 VDC Output, J8, is located on the bottom side of the amplifier as shown in Figure 2-3.
This provides +15 VDC and up to 1 Amp current to any external equipment. It is a 6-pin
MS-type connector (see Table 2-6 for pin-outs) and mates with MS3116F10-6P.
2.5.9 Chassis Ground Terminal
A Chassis ground terminal is provided on the bottom side of the amplifier. A ¼ - 20 threaded
terminal is provided for equipment grounding.
Table 2-6: +15 VDC Output Port (J8) Pin-Outs
Pin # on J8 Connection Pin # on J8 Connection
A EXTERNAL FAULT IN D GND
B FAULT PULLUP E +15V EXTERNAL
C +15V LNA F GND
Figure 2-4: Bottom View, Compact Outdoor Amplifier
AUX POWER
J8
MODEL: XXXX XXXXXXXX
P/N: LXXX XXX-X
S/N: XXXX
SAMPLE
J3
J7
AC IN

Operations Manual, HPA2, Compact Outdoor SSPA 208495 REV B 19
2.6 Airflow
The air intake and exhaust are both located on the bottom side of the amplifier. The intake is
brought through three fans while the exhaust is along the two rows of heatsink fins as seen in
Figure 2-4. A minimum clearance of 6 inches (152 mm) should be maintained between
the bottom of the amplifier and any mounting surface. This will ensure that there is no forced
re-circulation of airflow from exhaust to intake.
The Compact Outdoor SSPA should NEVER be mounted with the fans facing up.
The fans should be examined periodically and any
obstruction or debris should be cleared. Inadequate air
flow can cause the amplifier to overheat and cause a
temperature fault. See Section 6: Maintenance for
instructions on how to clean the fan assembly and
heatsink.
In system configurations, ensure that each unit in the
system has sufficient ambient airflow, and adequate
space to maintain the fans for each unit. Figure 2-5
shows an improper method for mounting a Compact
Outdoor SSPA system. Not only do the fans oppose
each other, thereby potentially causing thermal issues,
but the configuration leaves insufficient space to remove
the fans to periodically clean the heatsink.
The fans provide a maximum air flow of 103 CFM each (maximum air pressure of 0.691
inches H2O at zero air flow) and produce 54.0 dB-A measured at a distance of 1 meter from
the fan intake.
2.7 Unit Weights
The Compact Outdoor SSPA is available in a variety of frequency bands and power levels,
and have a multitude of options which makes each unit weigh slightly different from another.
The following chart, Table 2-7, outlines the weights for the most common power levels of
Compact Outdoor SSPA and additional weight add-ons for common options.
Figure 2-5: Improper mounting

20 208495 REV B Operations Manual, HPA2, Compact Outdoor SSPA
Table 2-7: Compact Outdoor SSPA Weights
Band Model Base Weight
lbs (kg)
With zBUC
lbs (kg)
With 110 VAC Option
lbs (kg)
C-Band
HPAC2030AC... 36.5 (16.6) +1.7 (+0.8) N/A
HPAC2040AC... 36.5 (16.6) +1.7 (+0.8) N/A
HPAC2050AC... 36.5 (16.6) +1.7 (+0.8) N/A
HPAC2075AC... 36.5 (16.6) +1.7 (+0.8) N/A
HPAC2100AC... 36.8 (16.7) +1.7 (+0.8) N/A
HPAC2140AC... 37.0 (16.8) +1.7 (+0.8) +1.9 (+0.9)
HPAC2200AC... 37.8 (17.2) +1.7 (+0.8) +1.2 (+0.6)
HPAC2250AC... 45.4 (20.6) +1.7 (+0.8) +1.2 (+0.6)
HPAC2300AC... 46.9 (21.3) +1.7 (+0.8) N/A
Ku-Band
HPAK2010AC... 35.1 (16.0) +1.7 (+0.8) N/A
HPAK2020AC... 35.1 (16.0) +1.7 (+0.8) N/A
HPAK2025AC... 35.1 (16.0) +1.7 (+0.8) N/A
HPAK2035AC... 35.1 (16.0) +1.7 (+0.8) N/A
HPAK2040AC... 35.3 (16.1) +1.7 (+0.8) N/A
HPAK2050AC... 35.7 (16.2) +1.7 (+0.8) N/A
HPAK2070AC... 35.7 (16.2) +1.7 (+0.8) N/A
HPAK2100AC... 42.5 (19.3) +1.7 (+0.8) +1.2 (+0.6)
HPAK2125AC... 42.5 (19.3) +1.7 (+0.8) +1.2 (+0.6)
X-Band
HPAX2060AC... 46.3 (21.1) +1.7 (+0.8) N/A
HPAX2075AC... 46.7 (21.2) +1.7 (+0.8) N/A
HPAX2100AC... 46.7 (21.2) +1.7 (+0.8) N/A
HPAX2140AC... 47.5 (21.6) +1.7 (+0.8) +1.2 (+0.6)
HPAX2200AC... 54.9 (25.0) +1.7 (+0.8) +1.2 (+0.6)
HPAX2250AC... 56.4 (25.6) +1.7 (+0.8) N/A
S-Band
HPAS2050AC... 36.0 (16.4) N/A N/A
HPAS2100AC... 36.0 (16.4) N/A N/A
HPAS2200AC... 44.0 (20.0) N/A N/A
HPAS2300AC... 44.0 (20.0) N/A N/A
Ka-
Band
HPAKA040AC… 44.3 (20.2) +1.7 (+0.8) N/A
HPAKA080AC... 44.3 (20.2) +1.7 (+0.8) N/A