ParaZero SafeAir M600 User manual

SafeAir Installation Guide
PZ-GE-035
Number of pages: 16
Last update: 31.12.2017
SafeAir
INSTALLATION GUIDE
M600

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 2of 16
Table of Contents
Referenced Documents ............................................................................................................................... 3
Safety Instructions ......................................................................................................................................... 3
In the Box ........................................................................................................................................................ 4
12 Installation steps........................................................................................................................................ 5
1. Connecting the legs and buzzer to the SafeAir plate ............................................................ 5
2. Connecting the TerminateAir to the DJI M-600 ....................................................................... 6
3. Connecting the RC cable to the PWM channels in the AP ................................................... 8
4. Connecting the parachute system to the air vehicle ............................................................ 9
5. Connect the power cable and the RC cable to the SMARTAIR ........................................... 9
6. Configuring the DJI M600 RC extension to enable Arm\Disarm & manual trigger of the
unit .............................................................................................................................................. 10
7. Activating the system ............................................................................................................... 12
8. The first flight ............................................................................................................................... 13
Take Off ........................................................................................................................................................ 15
Before Landing ............................................................................................................................................. 15
After Landing ................................................................................................................................................ 15
Normal Operational Guide......................................................................................................................... 16
1. Regular pre-flight (From the second flight and on) .............................................................. 16
2. Take off ....................................................................................................................................... 16
3. Before landing ............................................................................................................................ 16
4. After landing ............................................................................................................................... 16

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 3of 16
This guidebook will guide you through the installation of the ParaZero SafeAir M600 safety
recovery system on your DJI Matric 600\600Pro air vehicle.
Reference Documents
SmartAir user guide
Safety Instructions
Before you start the installation, please read these safety instructions carefully!
Following these instructions carefully, in the exact order they are written, is vital for
your own safety and safety of others.
The ParaZero SafeAir M600 is a safety system, designed to deploy almost instantaneously, by
using a special pyrotechnic mechanism, which must be handled with care.
The system incorporates two safety elements:
a. Safety pin (as seen below)
The safety pin electrically prevents the activation of the system. The system is packed and
shipped with the safety pin connected to the system. Do not remove the safety pin,until
specifically instructed in this guide.
b. Safety cover (as seen before)
The safety cover physically prevents the deployment of the parachute, in case of an
unintended triggering. It is designed for safety during transportation, storage and should be
applied at the end of each flight day. The cover will also provide an extra layer of protection
for your product against external damage. The system is packaged and shipped with the cover
stretched over the parachute canister.
Do not remove it until you finish the installation, and you are ready to fly.

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 4of 16
10
9
In the Box
The package you received includes the following parts (see image with numbering):
1. The main parachute system, including the parachute, a mounting plate
including the SmartAir,the electric wires, safety pin and safety cover.
All are already connected and ready to use.
2. The TerminateAir M600 with one cable connected to it.
3. 4 mounting legs.
4. 1 indication buzzer with electric cable connected to it.
5. 1 RC cable with two PWM connectors at the end.
6. 8+1(screws + washers + nuts) for connecting the legs to the mounting plate.
7. 12+1 M4 Screws for connection to the M-600 mounting plate (they replace
the existing screws) + a syringe with Loctite adhesive.
8. 12+1 M3 nylock nuts to connect the TerminateAir electric connection to
the bottom electric board
9. Pyro-dummy
10. 6+1 M3\8 screws and washers for physical connection of the TerminateAir
to the body of the M-600 (They replace the original DJI screws that
connected the cables).
11. Syringe with Loctite.
12. A set of tools for the connection.
12
9

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 5of 16
12 Installation Steps
1) Connecting the legs and buzzer to the SafeAir plate
a. Connect the leg that is
connected with the buzzer to the
front left leg (the LED on the
canister is the backside).
i. Before connecting the leg
with the buzzer, insert the
electric cable wire through
the upper rib, as shown.
ii. Insert the screws through the
buzzer and close. Make sure
to put washers on both sides
of the plate.
b. Connect the three remaining
legs to the plate as shown in the
picture.

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 6of 16
c. Connect the Buzzer connector
to the SMARTAIR, as shown.
Make sure to check the
alignment of the connector pins.
2) Connecting the TerminateAir to the DJI M-600
At all these stages make sure:
1. Not to connect the batteries to the Air vehicle!
2. The safety pin is secure in place
3. The safety cover stays attached to the plate!
Make sure the batteries are not connected to the air vehicle, if they are - remove
them. Then gently turn over the Air vehicle. In order to connect the TerminateAir, go
through the following steps:
a. Disconnect the landing gear
power cable
b. Remove the bottom plastic cover.
gently pull it upwards along the
“Pull” indications stickers.

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 7of 16
c. Open the six screws connecting the
power cables (each connects two
power cables for two engine
controllers), spread in a hexagon
shape. Then move the cables to the
sides.
d. Insert the TerminateAir above the
screws
e. Return the 12 power cables back to
their original place. Only this time it is
above the TerminateAir. Each has its
own screw. Make sure you connect it
to the right screw, as shown in the
figure below. Pay special attention to
the marking on the board, indicating
the GND and VOUT and connect
accordingly: Red wire to the VOUT,
and black wire to the GND.
Failing to do so, may create a shorten
the power supply and damage the
air vehicle.
f. Secure each terminal with a M3
nylock (8)
g. Connect the TerminateAir to the
body of the drone, by inserting the six
screws (10) and washers included in
the package. Make sure to apply
Loctite (11) to each screw before
inserting it.
Go through all the screws and nuts to verify they are firmly connected.

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 8of 16
h. Pull the cable attached to the
TerminateAir along the M5 arm.
i. Put back and attach the plastic
cover. Make sure to pull the landing
gear power cable through the plastic
cover as shown, and make sure that
the TerminateAir cable comes out
through the corner of the cover
pointing the M5 arm.
At all these stages make sure:
1. Not to connect the batteries to the Air vehicle!
2. The safety pin is in its place
3. The safety cover stays attached to the plate!
3) Connecting the RC cable to the PWM channels in the AP
a. Remove the upper cover
from the top of the drone, by
opening the top 5 screws.
b. Connect the two RC
connectors to two available
RC connections in the AP.
c. Write down the number of
channel you connected the
ARM connector (Fx), and the
Fire (triggering) connector
(Fy).
d. Put the back of the cable
alongside the GPS antenna
cable (Near battery
number).
e. Close the plastic cover.

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 9of 16
4) Connecting the parachute system to the air vehicle
a. Gently turn back the air
vehicle on its legs.
b. Position the parachute system
above the center plate, in the
correct orientation as seen in
the picture below. The two
motors colored in red, and the
arrows on the GPS antenna
show the front side of the
M-600.
The SmartAir computer is on
the back side of the canister.
c. Extract the original screws
near the arms positioned near
each of the SafeAir 600 legs.
d. Connect all 4 legs to the main
plate of the Air vehicle, each
with 3 screws. Before screwing
them, apply some Loctite to
the screws.
5) Connect the power cable and the RC cable to the SmartAir
a) Connect the power cable to the 6
pins connector with the circular icon
above it.
b) Connect the RC cable to the 6 pins
connector with the label “RC” above
it.
Be advised that mixing these cables
can permanently damage the
SmartAir.

SAFEAIR Installation Guide – M600
THIS DOCUMENT AND THE INFORMATION CONTAINED IN IT ARE PROPRIETARY AND COMMERCIALLY CONFIDENTIAL TO PARAZERO LTD. ANY
USE, DISCLOSURE, REPRODUCTION OR COPY BY ANY METHOD OF THIS DOCUMENT OR PARTS THEREOF, IS NOT ALLOWED EXCEPT BY THE
PRIOR WRITTEN AUTHORIZATION OF PARAZERO, AND THEN ONLY TO THE EXTENT AUTHORIZED.
Page 10 of 16
6) Configuring the DJI M600 RC extension to enable Arm\Disarm and manual
trigger of the unit
Step 1: Connect the drone and open DJI Assistant 2
Step 2: Select DJI M600 Pro and proceed to the next screen