Pard TA32 User manual

—2——3—
—1—
Operation manual
TA32 / 37 / 62 THERMAL IMAGING DEVICES
Usage and Precautions
◇
◇
TA Series products can be used on day time and at night. Please use 3.7V lithium
ion rechargeable battery.
User needs to remove the protection tape at battery, and charge battery until
full before first time use.
◇ Device maintenance or repairing work should be conducted by PARD official
authorized technicians, DO NOT open device case by any unrecognized technicians.
In case of failure, please contact your domestic Distributors at once for after sales
service. If any unauthorized mechanical work applied to the device will treat as
abandoning the warranty service.
◇ Do not have the device focus directly at high-intensity radiation sources such as
the sun, electric welding and strong laser. Detector will be damaged under direct
To users
Dear user
Thank you very much for choosing PARD infrared thermal imaging device.
Please read this manual carefully before your first use;
After you read, please keep this manual properly for easy reference in case of
problems during use afterwards.
Please read this user manual carefully and be sure to follow the procedures
elaborated in this manual to avoid components damage caused by improper
operation.
If this manual has any amendments due to any software version upgrade or any
other reasons, PARD will not provide separate notice to individual users, users are
recommended to visit PARD official website periodically for update information.

—6——7—
—5—
1、Product Overview
This product is a compact and lightweight multifunctional thermal imaging
device. Proving users high sensitivity, high refresh rate and high stability, which
suitable to use in natural observation, outdoor hunting and exploration, security
monitoring and marine operation, night patrol in different occasions.
Please do the following before using this product:
A. Open the package box, take out the equipment and accessories.
B. Check and confirm there has no missing parts.
C. Check the equipment body, objective lens, operation button, etc. are not
damaged.
D. Ensure all objective lenses and eyepieces clean and can be used properly.
Note: if any parts are missing or damaged, please contact our after-sales
department at once.
2、 Performance parameters
Model
Detector
NETD
Camera lens
Frame
rate
Optical
Magnificati
on
Field angle
Dimension (mm)
Detection
distance
Weight
(excluding
battery)
TA37
17μm
384*288
≦40mK
19/25/35mm
50Hz
1.7/2.2/3x
19.5º/14.9º
/10.7º
145/153/159*68*44
0.8/1.2/1.5km
288/300/328g
TA32
12μm
384*288
≦25mK
19/25/35mm
50Hz
2.7/3.5
/4.5x
13.8º/10.6º
/7.5º
145/153/159*68*44
1.2/1.6/2km
288/300/328g
TA62
12μm
640*480
≦25mK
25/35mm
30Hz
2/2.8x
17.5º/12.5º
153/158*68*44
1.5/1.8km
300/328g
General parameters
Digital zoom
1/2/4/6/8x
Focusing
range
1m-∞
Exit pupil distance
15mm
Diopter
adjustment
±5D
Battery
Li18650*1
Eyepiece
resolution
1024*768
OLED
Operating
Temperatur
e
- ∽30ºC +60ºC
Transmission mode
WiFi/HDMI
Protective
performanc
e
IP67
Storage type
TF Card
(max128G)
Frame rate
30 fps
Battery life
5H(Max)
Video format
MP4
Casing
material
AL6061 + Plastic
Voltage
3.7V
Video
resolution
1440*1080
Charging port type
TYPE-C
Image mode
White Hot/RedHot/BlackHot
/Edge/Sky/IronHot
Power Button
+ Key Menu Button - Key
Red dot indicator
Objective focusing wheel
Battery Compartment Cap
Data storage
Indicator light
Eyepiece focusing
wheel
—4—
focused at strong light source, and such corresponding defects will not under
warranty service.
◇ Please keep the device in temperature between - 40 º C to 60 º C.
◇ Original packaging must be used and cannot open during transportation.
◇
◇
◇
Recommend to keep the device in a place of cool, dry and ventilated environment
without strong electromagnetic field.
Avoid oil stains or any kinds of chemicals from contaminating and damaging the
lens surface.
After use, please put on the lens cover at once.

—9—
—11—
—10—
3.Press the [power key] to start up. In the power on status (after 15 seconds),
press the [power key], internal screen will enter in sleep mode, press [power key]
again to switch on the screen, long press [power key] to shut down.
1.Eyepiece focusing, also known as diopter adjustment, aim at enable users
with different vision conditions can clearly see the displayed content.
2.Turn the focusing wheel until you can see the text or icon on the screen
clearly.
3.
(the image
may not be clear when the objective lens is not well focused), this procedure is
done.
Eyepiece focusing
Please note that the image is not clearly visible after eyepiece focusing
adjustment, as long as the words on the display screen are clearly visible
Objective focusing
1.Before the objective lens focusing, please make sure you have the eyepiece
focusing (diopter adjustment) completed.
2.Focus at the target you want and adjust the focusing wheel of the objective
lens until you can see the target image sharply.
3.Generally, the focusing position of the objective lens is placed at objects
located far away from you.
Non menu mode (shortcut)
After startup, without pressing the [menu key] machine is in non menu mode
(15 seconds after startup)
1.Press [power key] to sleep / wake up the device; long press to shutdown.
4.Thermal imaging has the least focusing distance. It is normal an object may
not be able to see sharply within 3 meters.
5.Objects behind glasses cannot be detected.
There are two controlling key arrangements at the thermal imaging device,
which are
1: non menu mode (shortcut key mode)
2: menu mode (enter normal setting mode)
Key and interface operation method
Eyepiece focusing wheel
Objective focusing wheel
—8—
For the first time you use the device, follow the below steps: install the battery
> eyepiece focusing > objective focusing.
Install the battery
1.Please use 18650 lithium ion rechargeable 3.7V battery.
2.Press the battery compartment cover to open, install the battery positive
electrode towards the front objective lens. Put on the battery compartment cover
and well fasten it.
3、Installation and basic operation methods
push

—13—
—15—
—14—
Menu mode (setup mode)
Press [menu key] to enter the menu setting mode, and the interface is shown
as pictures below (at this time, the shortcut key is not function)
the target option value. Long press [menu key] to exit.
Image default settings:
The contrast value is 90, the brightness value is 65, the sharpness value is 2,
and the mode is 0.
2. Display setting: press [+ key] [- key] to move the cursor to the display setting
option, and press [menu key] to switch the contrast/ brightness / color option,
press [+ key] [- key] to adjust the option value. Long press [menu key] to exit.
Default value:
contrast is 3, brightness is 3, and color temperature is 3
3.Magnify Center Position: press [+ key] [- key] to move the cursor to the
magnify center position, press [menu key] to switch the X / Y axis option, press /
long press [+ key] [- key] to adjust the option value. Long press [menu key] to exit.
4. Picture in picture: press [+ key] [- key] to move the cursor to the picture in
picture option, and press [+ key] [- key] to select on/off the shortcut [+ key] picture
in picture function, press [menu key] to save and exit.
1. Image setting: press [+ key] [- key] move the cursor to the image setting
option, and press [menu key] to enter the sub menu, press [menu key] to switch the
contrast / brightness / sharpness / mode options, and press [+ key] [- key] to adjust
5.Shutter Correction: press [+ key] [- key] to move the cursor to the shutter
correction option, and press [menu key] to enter picture correction. Manual picture
correction can obtain better picture effect.
6. Hot Track: press [+ key] [- key] to move the cursor to the hot track option,
and press [menu key] to enter sub-menu. Press [+ key] [- key] to switch on and off
the thermal imaging tracking function. Press [menu key] to confirm and exit.
7.Auto Recording: press [+ key] [- key] to move the cursor to the automatic
video recording option, and press [menu key] to enter the sub-menu. Press [+ key] [-
key] to select on / off automatic video recording option, press [menu key] to
confirm and exit.
8.Loop Recording: press [+ key] [- key] to move the cursor to the loop recording
option, press [menu key] to enter the sub-menu, press [+ key] [- key] to select cyclic
recording off / 3minutes / 5minutes / 10minutes, press [menu key] to confirm and
exit.
1/3
Menu
Image Setting
Hot Track
Magnify Center Position
Display Setting
Picture In Picture
Shutter Correction
Auto Recording
Loop Recording
Long press MENU button to exit
—12—
2.Press the [+ key] to switch magnification function : 1,2,4,6,8 times. When the
picture in picture function is on, press the [+ key] to switch between magnifications
of 1,2,4,6,8; long press to enter the playback function menu.
In the playback interface menu, press [+ key] [- key] to switch the video /
picture mode in the TF card. When the interface is in video, press [menu key] can
play video. Press [+ key] [- key] to adjust the playback speed accordingly.
When playing video, press [menu key] to pause, press [+ key] [- key] to play by
frame, long press [menu key] exit to the previous folder to switch files, and long
press [menu key] again exit to the display interface.
3.Press [menu key] to enter the menu interface; long press to turn on / off the
video recording function.
4.Press [- key] to turn on / off the red dot indicator; long press to switch display
mode.

—18——19—
14.Date/Time: press [+ key] [- key] to move the cursor to the date/time, and
press [menu key] to enter the sub-menu, press [+ key] [- key] to adjust the setting
time value, press [menu key] to switch options, and long press [menu key] to exit
and save.
15.Format: press [+ key] [- key] to move the cursor to the format option, press
[menu key] to enter the sub-menu, press [+ key] [- key] to select Cancel / confirm,
and press [menu key] to confirm and exit the menu interface.
"Formatting will delete all data", please consider carefully before you confirm!
Data cannot be recovered after deleted.
16. Blind Pixel Compensation: press the [+ key] [- key] to move the cursor to
the blind spot repair option, and press the [menu key] to enter. You can see the
prompt.
Please put the lens cover on before blind spot repair, press the [menu key] to
—17—
11. Beep Sound for HDMI: press [+ key] [- key] to move the cursor to the beep
sound for HDMI option, and press [menu key] Enter the sub-menu, press [+ key] [-
key] to select on / off HDMI prompt tone, press [menu key] to confirm and exit.
12.WiFi: press [+ key] [- key] to move the cursor to the WiFi option, press
[menu key] to enter the sub-menu, and press [+ key] [- key] to select on / off WiFi
function, press [menu key] to confirm and exit.
The menu interface cannot be opened after the WiFi function is turned on.
Please turn off the WiFi hotspot by long pressing [+ key].
WiFi account is a string of characters starting with PARD, and the password is
12345678.
13.Language setting: press [+ key] [- key] to move the cursor to the language
setting option, press [menu key] to enter the sub-menu, press [+ key] [- key] to
select "English" / ""Français" /"Español" /"Português" "Deutsch"/ "Italiano"
/"Русский"/"Cesky" language, press [menu key] to confirm and exit.
start blind spot repair, which will be completed within ten seconds. After the repair
is completed, you can choose to save or cancel. If you cancel blind spot repair, long
press the [menu key].
17.Restore factory default setting: press [+ key] [- key] to move the cursor to
the restore default setting option, press [menu key] to enter the restore default
setting page, press [+ key] [- key] to select Cancel / confirm to restore the default
setting, press [menu key] to confirm and exit.
3/3
Menu
Default Setting
Version
Long press MENU button to exit
—16—
10:15
10. Record Audio: press [+ key] [- key] to move the cursor to the record audio
option, and press [menu key] to enter the sub-menu, press [+ key] [- key] to
select on / off recording audio, press [menu key] to confirm and exit.
2/3
Menu
Date Stamp
Date/Time
Beep Sound for HDMI
Record Audio
WiFi
Language
Format
Blind Pixel Compensatin
Long press MENU button to exit
9. Date Stamp: press [+ key] [- key] to move the cursor to the date stamp
option, press [menu key] to enter the sub-menu, press [+ key] [- key] to select on /
off date stamp, and press [menu key] to confirm and exit.

—22—
—21—
manufacturer at once. Maintenance, modification or product sealing sticker
rupture without the approval of PARD are not within the scope of warranty.
(2) Damage caused by human factors or accidents, including use under
abnormal working environment, damage caused by man-made failure to use and
install not according to the instructions, etc., are not within the scope of warranty.
(3) PARD reserves the right to modify and interpret the terms in this user
menu.
5、After sales support
PARD provides users with after-sales support services for the company's
products. If you need after-sales service support, please log on to our official
website www.pard-tech.com/support to fill in and submit the information. We will
get back to you within one working day.
In order to provide you with better service, we need you to fill in and submit
the following information:
1. Where you bought the machine
2. Your country/name/email address/telephone number
3. Machine models that need after-sales support
4. The SN code of the machine
5. Describe the problem encountered
—20—
4、Warranty description
Thank you for purchasing PARD product. During the warranty period, we will
provide you a quality after-sales service, in accordance with this warranty clause.
1： Warranty policy
PARD guarantees users of this product can get effective warranty under the
following conditions.
(1) This warranty card shall be provided at the same time.
(2) During the warranty period, faults caused under normal operation, not
man-made damages, shall be repaired and replaced free of charge.
2： Warranty limitations
When product is damaged and cannot be used due to the following reasons,
will not within the scope of warranty.
(1) Disassemble the machine by yourself. In case of failure, please contact the
—23—
6、Packing Contents
Item No.
Packing Contents
Quantity
Remark
1
Thermal imaging device
1
2
Shoulder bag
1
3
Hand strap
1
4
Type-C cable
1
5
Li-ion 18650 3.7V rechargeable battery
1
6
User manual
1
7
Warranty card
1
8
Cloth bag
1
9
Lens cap
1

Telephone：[phone]
Add:Building A Hengxingchang Industrial Park, Baoshi East Road,
Shiyan, Baoan,Shenzhen,518000, China
Website：www.pard-tech.com
联系电话：400-099-2599
网址：www.puleide.com
地址：深圳市宝安区宝石东路328号A栋