Parker PVD 3642-EN User manual

 Copyright 2011 Parker Hannifin Manufacturing Limited
All rights strictly reserved. o part of this document may be stored in a retrieval system, or
transmitted in any form or by any means to persons not employed by a Parker Hannifin
Manufacturing Limited company without written permission from Parker Hannifin Manufacturing Ltd.
Although every effort has been taken to ensure the accuracy of this document it may be
necessary, without notice, to make amendments or correct omissions. Parker Hannifin
Manufacturing Limited cannot accept responsibility for damage, injury, or expenses resulting
therefrom.
i
WARRA TY
Refer to Parker Hannifin Manufacturing Limited Terms and Conditions of Sale. These documents are available on
request at www.parker.com.
Parker Hannifin Manufacturing Limited reserves the right to change the content and product specification without
notice.
IA387648C225 Issue C
Supporting Title - e.g. software version
PVD 3642-E
(5703-2)

1
5703
57035703
5703-
--
-2
22
2 I
II
I NSTALLATION
NSTALLATIONNSTALLATION
NSTALLATION
Description :
Example for two drives (590P) Example for more than two drives (590P)
The
5703
-
2
unit provides the facility to
run a line of drives in speed-lock.For
accurate speed holding, encoder
feedback is required.
The 5703-2 unit converts the signal into a
fibre optic signal for transmission and
when receiving converts the optical signal
to RS232 signal.
The 5703-2 is simply an electric signal to
light converter and does not alter the
signal in any way.
5703/2 Wiring Diagram :
Fibre optic cable
4 ways cable Rs 232
Rx
Tx1
Tx1
Rx
Tx1
Tx2
Tx1
Rx
Rx
Rx
Fibre optic cable

2
Configuration
Example for two drives (690P)
TX1
Rx
Fibre optic cable
With a 690P you must
connect the terminal 20
of the drive with the
+24V of the unit
4 ways cable Rs 232
Fibre optic cable
Rx Rx
Tx1
Rx
Tx1
Tx2
Example for more than two drives (690P)
The jumper position determines the signal transmitted
by TX2.
Two cases :
-When the jumper connects Pin1 and 2 , TX2 re-
transmits the input received from RX.
- When the jumper connects Pin2 and 3, TX2 transmits
the same signal as TX1.
The signal between SK1 and TX1 is not configurable

3
5703
57035703
5703-
--
-2
22
2 HARDWARE
HARDWARE HARDWARE
HARDWARE D
DD
D ESCRIPTION
ESCRIPTIONESCRIPTION
ESCRIPTION
The 5703-2 is intended for DIN rail mounting . It operates using a +24V dc supply.
Each unit is fitted with one fibre optic receiver and two fibre optic transmitters:
. The Receiver accepts data from the precedent unit.
. Transmitter 1 sends data to the following unit.
. Transmitter 2 can be selected to send either the incoming signal, or to repeat the output signal.
The P3 port must be configured for 5703 support on each drive.
Use the MMI , or a suitable programming tool.
Refer to the (software) Product Manual: “Programming Your Application”.
Mechanic
Level of Protection : IP20
Weight : 100 gr
Dimension : H:127 mm W:22 mm D: 152 mm
Mounting : Din rail mounting (symmetric and asymmetric)
Mounting of the unit on the rail DIN
Dismounting of the unit on the rail DIN
Push in the direction of the arrow

4
5703
57035703
5703-
--
-2
22
2 T
TT
T ECHNICAL
ECHNICAL ECHNICAL
ECHNICAL S
SS
S PECIFICATIONS
PECIFICATIONSPECIFICATIONS
PECIFICATIONS
Environmental
Temperature : -10 °C to +60° C
Humidity : 10 to 90% non condensating
Power Supply
Voltage : 21V to 26V dc
Supply : - by the 4 ways cable R232 (1&2) 60 cm MAX
- by the connector at the bottom of the unit
Module Current: 79 mA max (all the I/O active)
Fuse: 160 mA 250V Fast
Unit is powered: Green Led on front
Electrical Specifications
Type of Connector : RS232 (female) for male connector RJ11
Type of signal : RS232 Bi directional 2400 to 38000 bit/s
Port 5703/2 : Drive Port :
Optical specifications
Connector type : Fast less crimping Serial:HFBR453X(HP)
Number of connector : 3 connectors (1 input, 2 outputs) see configuration
Wavelength of signal : 660 nm (Red visible)
Length of fibre between two module : 40 centimeters to 25 meters
+24V
TX
0V
RX