Parkside PABS 20-LI B2 User manual

IAN 274864
CORDLESS DRILL PABS 20-LI B2
CORDLESS DRILL
Translation of the original instructions BATTERIDREVET BORE-/
SKRUEMASKINE
Oversættelse af den originale driftsvejledning
AKKU-BOHRSCHRAUBER
Originalbetriebsanleitung
PERCEUSE-VISSEUSE SANS FIL
Traduction des instructions d’origine
ACCUBOORSCHROEFMACHINE
Vertaling van de originele gebruiksaanwijzing

GB Translation of the original instructions Page 1
DK Oversættelse af den originale driftsvejledning Side 11
FR/BE Traduction des instructions d’origine Page 23
NL/BE Vertaling van de originele gebruiksaanwijzing Pagina 35
DE/AT / CH Originalbetriebsanleitung Seite 47
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
device.
Før du læser, vend begge sidene med billeder frem og bliv bekendt med alle apparatets funktioner.
Avant de lire le mode d’emploi, ouvrez les deux pages contenant les illustrations et familiarisez-vous
ensuite avec toutes les fonctions de l’appareil.
Vouw vóór het lezen de beide pagina‘s met de afbeeldingen open en maak u vertrouwd met alle functies
van het apparaat.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Gerätes vertraut.

A

B C
D E
F G

H I
J K
L

PABS 20-LI B2 GB │ 1 ■
Contents
Introduction......................................................2
Intended use................................................................ 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical details ............................................................. 2
General Power Tool Safety Warnings ................................3
1. Work area safety.......................................................... 3
2. Electrical safety ........................................................... 3
3. Personal safety............................................................ 4
4. Power tool use and care .................................................... 4
5. Use and handling of the cordless electrical power tool............................. 5
6. Service .................................................................. 5
Safety guidelines for cordless screw drivers........................................ 5
Safety guidelines for battery chargers ............................................ 5
Before use .......................................................6
Charging the battery pack (see fig. A)............................................ 6
Attaching/disconnecting the battery pack to/from the appliance....................... 6
Checking the battery charge level ............................................... 6
Changing tools.............................................................. 6
Torque selection ring/drill setting ................................................ 6
2 speed gearbox ............................................................ 6
Operation .......................................................7
Switching on and off ......................................................... 7
Adjusting the rotational speed .................................................. 7
Changing the direction of rotation ............................................... 7
Tips and tricks............................................................... 7
Maintenance and cleaning..........................................8
Kompernass Handels GmbH warranty ...............................8
Service..........................................................9
Importer ........................................................9
Disposal........................................................10
Translation of the original Conformity Declaration .....................10

PABS 20-LI B2
■ 2 │ GB
CORDLESS DRILL PABS 20-LI B2
Introduction
Congratulations on the purchase of your new ap-
pliance. You have selected a high-quality product.
The operating instructions are part of this product.
They contain important information about safety,
usage and disposal. Before using the product, please
familiarise yourself with all operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
This appliance is designed for screwing and drill-
ing into wood, plastic and metal. Use this product
only as described and for the areas of applications
specified. Any other usage of or modification to the
appliance is deemed to be improper and carries a
significant risk of accidents. The manufacturer ac-
cepts no responsibility for damage(s) attributable
to misuse. This appliance is not intended for com-
mercial use.
Features
Gear selector
Bit holder (magnetic)
Rotational direction switch/lock
ON/OFF switch/speed control
Belt clip
Battery charge level button
Battery display LED
Battery pack
Release button for battery pack
LED work light
Chuck
Torque selection ring
High-speed charger
Red charge control LED
Green charge control LED
Package contents
1 cordless drill PABS 20-Li B2
1 high-speed battery charger PABS 20-Li B2-2
1 battery pack PABS 20-Li B2-1
1 bit PH2 50 mm
1 carrying case
1 set of operating instructions
Technical details
Cordless drill: PABS 20-Li B2
Rated voltage: 20 V (DC)
Rated idle speed: 1st gear: n00–400 rpm
2nd gear: n00–1400 rpm
Chuck clamping
range : max. Ø 13 mm
Max. drill diameter: Steel: 13 mm
Wood: 30 mm
Battery: PABS 20-Li B2-1
Type: LITHIUM ION
Cells 5
Rated voltage: 20 V (DC)
Capacity: 2.0 Ah
Energy value: 40 Wh
High-speed battery charger: PABS 20-Li B2-2
INPUT:
Rated voltage: 230–240 V ~, 50 Hz
(AC)
Rated power
consumption: 65 W
Fuse (internal): 2 A T2A
OUTPUT:
Rated voltage: 21,5 V (DC)
Rated current: 2.3 A
Charging time: approx. 60min.
Protection class: II/ (double insulation)

PABS 20-LI B2 GB │ 3 ■
Noise emission value:
Noise measurement value determined in accord-
ance with EN 60745. The A-rated noise level
of the power tool is typically as follows:
Sound pressure level: LpA = 68.5 dB(A)
Uncertainty K: KpA = 3 dB
Sound power level: LWA = 79.5 dB(A)
Uncertainty K: KWA = 3 dB
Vibration emission value:
Total vibration values (vector total of three directions)
determined in accordance with EN 60745:
Screwing: Vibration emission value
ah: 0.601 m/s2
Uncertainty K = 1.5 m/s2
Drilling in metal: Vibration emission value
ah,D : 1.070 m/s2
Uncertainty K = 1.5 m/s2
NOTE
► The vibration level specified in these instruc-
tions has been measured in accordance with
the standardised measuring procedure speci-
fied and can be used to make equipment
comparisons. The specified vibration emission
value can also be used to make an initial
exposure estimate.
WARNING!
► The vibration level varies in accordance with
the use of the power tool and may be higher
than the value specified in these instructions
in some cases. Regular use of the electric
tool in such a way may cause the user to
underestimate the vibration. Try to keep the
vibration loads as low as possible. Measures
to reduce the vibration load are, e.g. wearing
gloves and limiting the working time. Wherein
all states of operation must be included (e.g.
times when the power tool is switched off and
times where the power tool is switched on but
running without load).
General Power Tool
Safety Warnings
WARNING!
► Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts.Damaged or entangled
cords increase the risk of electric shock.

PABS 20-LI B2
■ 4 │ GB
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.Use of an RCD re-
duces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing ac-
cessories or storing power tools. Such preven-
tive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many ac-
cidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits,
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.

PABS 20-LI B2 GB │ 5 ■
5. Use and handling of the cordless
electrical power tool
a) Charge a rechargeable battery unit using only
the charger recommended by the manufactur-
er. Chargers are often designed for a particular
type of rechargeable battery unit. There is the
danger of fire if other types of rechargeable
battery units are used.
b) Only the rechargeable battery units supplied
are to be used with an electrical power tool.
The use of other rechargeable battery units may
lead to the danger of injury or fire.
c) When they are not being used, store recharge-
able battery units away from paperclips, coins,
keys, nails, screws or other small metal objects
that could cause the contacts to be bridged.
Short-circuiting the contacts of a rechargeable
battery unit may result in heat damage or fire.
d) Fluids may leak out of rechargeable battery
units if they are misused. If this happens, avoid
contact with the fluid. If contact occurs, flush
the affected area with water. Seek additional
medical help if any of the fluid gets into your
eyes. Escaping battery fluid may cause skin
irritation or burns.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries!
Protect the rechargeable battery from
heat, for example from continuous
exposure to sunlight, fire, water and
moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Safety guidelines for cordless screw
drivers
WARNING!
■Hold the power tool by the insulated
gripping surfaces when performing an
operation where the screw or attached tool
could come into contact with hidden wiring.
Contact between the screw or attached tool
and a live wire may cause exposed metal
parts of the power tool to become live and
give the operator an electric shock.
Safety guidelines for battery chargers
■ This appliance may be used by chil-
dren aged 8 years and above and
by persons with limited physical,
sensory or mental capabilities or
lack of experience and knowledge,
provided that they are under super-
vision or have been told how to use
the appliance safely and are aware
of the potential risks. Children must
not play with the appliance. Clean-
ing and user maintenance tasks
may not be carried out by children
unless they are supervised.
The charger is suitable for in-
door use only.
WARNING!
■ To avoid potential risks, damaged mains cables
should be replaced by the manufacturer or
the manufacturer’s customer service depart-
ment or a similarly qualified person.

PABS 20-LI B2
■ 6 │ GB
Before use
Charging the battery pack (see fig. A)
CAUTION!
► Always pull out the plug before you remove
the battery pack from or connect the
battery pack to the charger.
■ Never charge the battery pack when the
ambient temperature is below 10°C or above
40°C.
♦ Connect the battery pack to the rapid bat-
tery charger (see Fig. A).
♦ Insert the power plug into the socket. The con-
trol LED lights up red to indicate that the
appliance is charging.
♦ The green control LED indicates that the
charging process is complete and the battery
pack is ready.
♦ Insert the battery pack back into the appli-
ance (see Fig. B).
Attaching/disconnecting the battery
pack to/from the appliance
Inserting the battery pack:
♦ Push the rotation direction switch into the
middle position (lock) (see Fig. C). Allow the bat-
tery pack to click into the handle (see Fig. B).
Removing the battery pack:
♦ Press the release button and remove the bat-
tery pack (see Fig. D).
Checking the battery charge level
♦ Press the battery charge level button to check
the charge level of the battery (see Fig. E). The
status/remaining charge will be shown on the
battery display LED as follows:
♦ GREEN/RED/ORANGE = maximum charge/
performance
RED/ORANGE = medium charge/performance
RED = low charge – charge the battery
Changing tools
Your cordless drill has a fully automatic spindle
lock .
When the motor is stopped, the power train locks
so that the chuck can be opened by turning
it . After you have attached the desired tool
and tightened it by turning the chuck , you can
continue working (see Fig. F). The spindle lock is
automatically released when the motor starts (ON/
OFF switch pressed).
Torque selection ring/drill setting
You can set the torque using the torque selection
ring (see Fig. G).
♦ Select a low level for small screws or soft materials.
♦ Select a high level for large screws, hard materi-
als or removing screws.
♦ Select the drill setting for drilling work by adjust-
ing the torque selection ring to the position
(see Fig. H).
2 speed gearbox
CAUTION!
► Only operate the gear selection switch
when the appliance is at a standstill. Other-
wise the appliance can be damaged.
In first gear (gear selector switch in posi-
tion: 1) (see Fig. I)
you can reach a speed of approx. 400 rpm and a
high torque. This setting is suitable for all screwing
jobs.
In second gear (gear selector switch in
position: 2) (see Fig. J)
you can reach a speed of approx. 1400 rpm for
carrying out drilling work.

PABS 20-LI B2 GB │ 7 ■
Operation
Switching on and off
Switching on:
♦ To start the appliance, press the ON/OFF
switch and keep it pressed in (see Fig. K).
The LED work light lights up when the ON/
OFF switch is depressed lightly or fully. This
allows for illumination of the work area in low
lighting.
Switching off:
♦ Release the appliance's ON/OFF switch to
switch off the appliance.
Adjusting the rotational speed
The ON/OFF switch has a variable speed con-
trol. Pressing the ON/OFF switch lightly yields a
low speed. Increasing pressure increases the speed
(see Fig. K).
NOTE
► The integrated motor brake ensures rapid
stoppage.
Changing the direction of rotation
♦ Change the direction of rotation by pressing the
rotational direction switch towards the left or
right (see Fig. L).
Tips and tricks
Tip! This symbol indicates proper be-
haviour!
♦ Before operation, check whether the screw or
drill bit is correctly positioned, i.e. centred in the
drill chuck.
♦ Screw bits are labelled according to their di-
mensions and their shape. If you are uncertain,
always check whether the bit fits tightly in the
screw head without any free play.
Torque:
♦ Smaller screws/bits can be damaged if you set
the torque or rotational speed too high.
Hard screw joints (in metal):
♦ Particularly high torques occur, for example, in
metal screw joints made using drive sockets.
Select a low rotational speed.
Soft screw joints (e.g. in soft wood):
♦ Again, use a low rotational speed, to avoid e.g.
damaging the surface of the wood upon contact
with the screw head. Use a countersink.
When drilling in wood, metal and other
materials, observe the following:
♦ Use a high speed for drill bits with small diameter
and a low speed for drill bits with large diameter.
♦ Select a low speed for hard materials and a
high speed for soft materials.
♦ Secure or fasten the workpiece in a clamp or
vice (if possible).
♦ Mark the spot where you want to drill using a
centre punch or nail. Select a low rotational
speed when starting.
♦ Pull the rotating drill bit from the hole repeatedly
to remove dust and chips and clear the hole.

PABS 20-LI B2
■ 8 │ GB
Drilling in metal:
♦ Use a metal drill (HSS). For optimum results,
cool the drill bit with cutting oil. Metal drill bits
can also be used to drill into plastics. Start with
a 3 mm diameter drill bit and then increase the
size until the desired hole diameter is achieved.
Drilling in wood:
♦ Use a wood drill with a lathe centre; for deep
holes, use an auger bit; for large-diameter
holes, use a Forstner bit. Small screws can be
screwed directly into soft wood.
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch the appliance off and remove
the battery before carrying out any
work on the appliance.
The cordless drill is maintenance-free.
■ The appliance must always be kept clean, dry
and free from oil or grease.
■ Never allow liquids to get into the appliance.
■ Use a soft, dry cloth to clean the housing.
Never use petrol, solvents or cleansers which
can damage plastic.
■ If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The optimum storage
environment is cool and dry.
NOTE
► Replacement parts not listed (such as batter-
ies, switches) can be ordered via our service
hotline.
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.
If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is depend-
ent on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.
If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.
Warranty period and statutory
claims for defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.

PABS 20-LI B2 GB │ 9 ■
Scope of the warranty
This appliance has been manufactured in accord-
ance with strict quality guidelines and inspected
meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product
parts subject to normal wear and tear or fragile
parts such as switches, batteries, baking moulds or
parts made of glass.
The warranty does not apply if the product has been
damaged, improperly used or improperly main-
tained. The directions in the operating instructions
for the product regarding proper use of the product
are to be strictly followed. Uses and actions that are
discouraged in the operating instructions or which
are warned against must be avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper handling,
use of force and modifications/repairs which have
not been carried out by one of our authorised
Service centres.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
▯ Please have the till receipt and the item number
(e.g. IAN 12345) available as proof of purchase.
▯ You will find the item number on the type plate,
an engraving on the front page of the instructions
(bottom left), or as a sticker on the rear or bottom
of the appliance.
▯ If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
▯ You can return a defective product to us free of
charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about
what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and software on
www.lidl-service.com.
Service
WARNING!
►Have the power tool repaired by the Service
centre or a qualified electrician and only
using genuine replacement parts.This will
ensure that the safety of the appliance is
maintained.
►Always ensure that the power plug or
the mains cable is replaced only by the
manufacturer of the appliance or by an
approved customer service provider.This
will ensure that the safety of the appliance is
maintained.
Service Great Britain
Tel.: [phone] (£ 0.10/Min.)
E-Mail: k[email protected]
IAN 274864
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com

PABS 20-LI B2
■ 10 │ GB
Disposal
The packaging is made from environmen-
tally friendly material and can be dis-
posed of at your local recycling plant.
Do not dispose of power tools in
your normal household waste!
European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.
Do not dispose of batteries in your
normal domestic waste!
Defective or worn-out rechargeable batteries must
be recycled according to Directive 2006/66/EC.
Take the battery pack and/or appliance to a
nearby collection facility.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
Translation of the original
Conformity Declaration
We, KOMPERNASS HANDELS GMBH, docu-
ments officer: Mr. Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, GERMANY, hereby declare that
this product complies with the following standards,
normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EC Low Voltage Directive
(2014/35/EU)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)
Applied harmonised standards:
EN 60745-1:2009/A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
EN 60335-1:2012/A11:2014
EN 60335-2-29:2004/A2:2010
EN 62233:2008
EN 55014-1:2006/A2:2011
EN 55014-2:1997/A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
Type/appliance designation:
Cordless drill PABS 20-Li B2
Year of manufacture: 04- 2016
Serial number: IAN 274864
Bochum, 05/02/2016
Semi Uguzlu
- Quality Manager -
Subject to technical changes due to product devel-
opment.

PABS 20-Li B2 DK │ 11 ■
Indholdsfortegnelse
Indledning ......................................................12
Anvendelsesområde......................................................... 12
Udstyr....................................................................12
Pakkens indhold ............................................................12
Tekniske data ..............................................................12
Generelle sikkerhedsanvisninger til elværktøjer ......................13
1. Sikkerhed på arbejdspladsen ............................................... 13
2. Elektrisk sikkerhed ........................................................14
3. Personsikkerhed .......................................................... 14
4. Anvendelse og behandling af elværktøjet ......................................15
5. Anvendelse og behandling af det genopladelige værktøj.......................... 15
6. Service .................................................................15
Sikkerhedsanvisninger for skruemaskiner .........................................16
Sikkerhedsanvisninger for opladere .............................................16
Førførstebrug ..................................................16
Opladning af batteripakke (se fig. A) ........................................... 16
Indsætning / udtagning af batteripakke .........................................16
Kontrol af det genopladelige batteris tilstand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Skift af værktøj .............................................................17
Forvalg af drejningsmoment/boretrin............................................ 17
2-trins gear ................................................................17
Førstebrug .....................................................17
Tænd / sluk ...............................................................17
Indstilling af omdrejningstal ................................................... 17
Omskiftning af omdrejningsretning.............................................. 17
Tips og tricks...............................................................18
Vedligeholdelse og rengøring......................................18
Garanti for Kompernass Handels GmbH .............................19
Service.........................................................20
Importør .......................................................20
Bortskaffelse....................................................20
Oversættelse af den originale overensstemmelseserklæring ............21

PABS 20-Li B2
■ 12 │ DK
BATTERIDREVET BORE-/
SKRUEMASKINE PABS 20-LI B2
Indledning
Tillykke med købet af dit nye produkt. Du har valgt
et produkt af høj kvalitet. Betjeningsvejledningen
er en del af dette produkt. Den indeholder vigtige
informationer om sikkerhed, anvendelse og bort-
skaffelse. Du bør sætte dig ind i alle produktets
betjenings- og sikkerhedsanvisninger før brug. Brug
kun produktet som beskrevet og kun til de angivne
anvendelsesområder. Lad vejledningen følge med
produktet, hvis du giver det videre til andre.
Anvendelsesområde
Dette produkt er beregnet til at bore og skrue i træ,
plast og metal. Brug kun produktet som beskrevet
og kun til de angivne anvendelsesområder. Enhver
anden anvendelse eller ændring af produktet anses
for at være uden for anvendelsesområdet og in-
debærer betydelige farer for uheld. Producenten
påtager sig intet ansvar for skader, der opstår som
følge af anvendelse uden for anvendelsesområdet.
Produktet er ikke beregnet til erhvervsmæssig brug.
Udstyr
Gearvælgerknap
Bit-holder (magnetisk)
Rotationsretningsomskifter / spærring
TÆND-/SLUK-knap / hastighedsregulator
Bælteholder
Batterikontrolknap
Genopladeligt batteri-display-LED
Batteripakke
Knap til frigørelse af batteripakke
LED-arbejdslys
Borepatron
Forvalg af drejningsmoment
Hurtigoplader
Rød LED til kontrol af opladning
Grøn ladekontrol-LED
Pakkens indhold
1 batteridrevet bore-/skruemaskine PABS 20-Li B2
1 hurtigoplader PABS 20-Li B2-2
1 batteripakke PABS 20-Li B2-1
1 bit PH2 50 mm
1 kuffert
1 betjeningsvejledning
Tekniske data
Batteridrevet bore-/skruemaskine: PABS 20-Li B2
Mærkespænding: 20 V
(jævnstrøm)
Nominel
tomgangshastighed: 1. gear: n00 - 400 min-1
2. gear: n00 - 1400 min-1
Borepatronens
spændeområde : maks. Ø 13 mm
Maks. borediameter: Stål: 13 mm
Træ: 30 mm
Genopladeligt batteri: PABS 20-Li B2-1
Type: LITHIUM-ION
Celler 5
Mærkespænding: 20 V
(jævnstrøm)
Kapacitet: 2,0 Ah
Energiindhold: 40 Wh
Hurtigoplader til genopladelige
batterier: PABS 20-Li B2-2
INDGANG/input:
Mærkespænding: 230 - 240 V ~, 50 Hz
(Vekselspænding)
Nominelt effektforbrug: 65 W
Sikring (indeni): 2 A T2A
UDGANG/output:
Mærkespænding: 21,5 V
(jævnstrøm)
Mærkestrøm: 2,3 A
Opladningstid: ca. 60 min
Beskyttelsesklasse: II/
(dobbeltisolering)

PABS 20-Li B2 DK │ 13 ■
Støjemissionsværdi:
Måleværdi for støj beregnet iht. ENISO 60745.
Det A-vægtede støjniveau for elværktøjet er typisk
som følger:
Lydtrykniveau: LPA = 68,5 dB (A)
Usikkerhed K: KPA = 3 dB (A)
Lydeffektniveau: LWA = 79,5 dB (A)
Usikkerhed K: KWA = 3 dB (A)
Vibrationsemissionsværdi:
Samlede vibrationsværdier (vektorsum i tre retninger)
beregnet iht. EN60745:
Skruning: Vibrationsemissionsværdi
ah: 0,601 m/s2
Usikkerhed K = 1,5 m/s2
Boring i metal: Vibrationsemissionsværdi
ah,D: 1,070 m/s2
Usikkerhed K = 1,5 m/s2
BEMÆRK
► Vibrationsniveauet, som er angivet i disse an-
visninger, er målt med en standard-måleme-
tode og kan anvendes til sammenligning af
elværktøjer. Den angivne vibrationsemissions-
værdi kan også anvendes til en indledende
vurdering af faren ved vibrationsniveauet.
ADVARSEL!
► Vibrationsniveauet ændrer sig afhængigt
af elværktøjets anvendelse og kan i mange
tilfælde ligge over den værdi, som er angivet
i disse anvisninger. Vibrationsbelastningen
kan undervurderes, hvis elværktøjet jævnligt
anvendes på denne måde. Prøv at holde
belastningen forårsaget af vibrationer så
lav som muligt. Vibrationsbelastningen kan
f.eks. reduceres ved brug af handsker under
anvendelse af værktøjet samt ved nedsæt-
telse af den tid, hvor værktøjet bruges. Her
skal der tages hensyn til hele driftscyklussen
(f.eks. perioder, hvor elværktøjet er slukket,
og perioder, hvor det er tændt, men kører
uden belastning).
Generelle sikkerheds-
anvisninger til
elværktøjer
ADVARSEL!
► Læs alle sikkerhedsanvisninger og -instruktio-
ner. Hvis de angivne sikkerhedsanvisninger
og -instruktioner ikke overholdes, kan det
medføre elektrisk stød, brand og/eller alvor-
lige kvæstelser.
Opbevar sikkerhedsanvisningerne og
-instruktionerne til senere brug.
Begrebet "elværktøj", der anvendes i sikkerheds-
anvisningerne, henviser både til elværktøj, der
anvendes med ledning til lysnettet, og batteridrevet
elværktøj (uden strømledning).
1. Sikkerhed på arbejdspladsen
a) Hold arbejdspladsen ren og godt oplyst. Rod
og dårligt oplyste arbejdspladser kan medføre
uheld.
b) Arbejd aldrig med elværktøj i eksplosionsfar-
lige omgivelser, hvor der befinder sig brænd-
bare væsker, gasser eller støv. Elværktøj danner
gnister, som kan antænde støvet eller dampene.
c) Hold børn og andre personer på afstand, når
elværktøjet bruges. Hvis du bliver distraheret,
kan du miste kontrollen over produktet.

PABS 20-Li B2
■ 14 │ DK
2. Elektrisk sikkerhed
a) Elværktøjets tilslutningsstik skal passe til stik-
kontakten. Stikket må ikke ændres på nogen
måde. Der må ikke bruges adapterstik sam-
men med beskyttelsesjordet elværktøj. Uæn-
drede stik og de rigtige stikkontakter reducerer
risikoen for elektrisk stød.
b) Undgå kropskontakt med jordforbundne over-
flader som f.eks. rør, radiatorer, komfurer og
køleskabe. Der er øget risiko for elektrisk stød,
hvis din krop har jordforbindelse.
c) Hold elværktøjet væk fra regn og fugt. Hvis
der trænger vand ind i elværktøjet, øges risikoen
for elektrisk stød.
d) Brug ikke ledningen til noget, den ikke er
beregnet til, f.eks. til at bære eller hænge
værktøjet op i eller til at trække stikket ud af
stikkontakten. Hold ledningen på afstand af
varme, olie, skarpe kanter eller produktets
bevægelige dele. Beskadigede eller sammenfil-
trede ledninger øger risikoen for elektrisk stød.
e) Hvis du anvender elværktøj udendørs, skal
der bruges en forlængerledning, som er god-
kendt til brug udendørs. Når du anvender en
forlængerledning, der er beregnet til udendørs
brug, reduceres risikoen for elektrisk stød.
f) Hvis det ikke er muligt at undgå at bruge
elværktøjet i fugtige omgivelser, skal der
installeres en fejlstrømsafbryder. Installation
af en fejlstrømsafbryder reducerer risikoen for
elektrisk stød.
3. Personsikkerhed
a) Vær altid opmærksom og bevidst om, hvad du
laver, og arbejd fornuftigt med elværktøjet.
Brug ikke elværktøjet, hvis du er ukoncentreret
eller påvirket af narkotika, alkohol eller medi-
cin. Selv et øjebliks uopmærksomhed ved brug
af elværktøjet kan medføre alvorlige kvæstelser.
b) Brug personligt beskyttelsesudstyr, og bær
altid beskyttelsesbriller. Når du bruger per-
sonligt beskyttelsesudstyr som f.eks. støvmaske,
skridsikre sikkerhedssko, beskyttelseshandsker,
sikkerhedshjelm og høreværn afhængigt af
elværktøjets type og anvendelse, reduceres
risikoen for kvæstelser.
c) Undgå utilsigtet igangsætning. Kontrollér at
elværktøjet er slukket, før du forbinder det
med elforsyningen og/eller tilslutter batteriet,
tager elværktøjet op eller bærer det. Hvis du
bærer elværktøjet rundt med fingeren på kon-
takten, eller hvis elværktøjet sluttes til strømfor-
syningen, mens det allerede er tændt, kan der
opstå uheld.
d) Fjern indstillingsværktøj eller skruenøgler,
før du tænder elværktøjet. Hvis der sidder et
værktøj eller en skruenøgle på en roterende del
af elværktøjet, kan det medføre personskader.
e) Undgå unormale kropsstillinger. Sørg for, at
du står sikkert, og hold altid balancen.
Derved kan du bedre kontrollere elværktøjet i
uventede situationer.
f) Bær velegnet påklædning. Bær ikke løstsid-
dende tøj eller smykker. Hold hår, tøj og
handsker på afstand af dele, der bevæger
sig. Løst tøj, smykker eller hår kan gribe fat i
dele, der bevæger sig.
g) Hvis der monteres opsugnings- og opsam-
lingsanordninger, skal disse tilsluttes og
anvendes korrekt. Anvendelse af denne type
anordninger nedsætter støvrisikoen.

PABS 20-Li B2 DK │ 15 ■
4. Anvendelse og behandling af
elværktøjet
a) Overbelast ikke elværktøjet. Brug et elværktøj,
der er egnet til arbejdet. Du arbejder bedre
og mere sikkert i det angivne effektområde,
hvis du bruger det rigtige elværktøj.
b) Brug ikke elværktøj med defekt kontakt.
Elværktøj, som ikke længere kan tændes og
slukkes, er farligt og skal repareres.
c) Træk stikket ud af stikkontakten, og/eller fjern
det genopladelige batteri, før du foretager
indstillinger på elværktøjet eller tilbehørsde-
lene eller lægger elværktøjet fra dig. Disse
forholdsregler forhindrer, at elværktøjet starter
ved en fejl.
d) Opbevar elværktøj uden for børns række-
vidde, når værktøjet ikke anvendes. Personer,
som ikke kender produktet, eller som ikke har
læst disse anvisninger, må ikke bruge produk-
tet. Elværktøj er farligt, hvis det anvendes af
uerfarne personer.
e) Vedligehold elværktøjet omhyggeligt. Kon-
trollér, om bevægelige dele fungerer, som
de skal og ikke sætter sig fast, om dele er
defekte eller så beskadigede, at elværktøjets
funktion er påvirket. Få beskadigede dele
repareret, inden du bruger produktet. Mange
uheld skyldes dårligt vedligeholdt elværktøj.
f) Hold skærende værktøjer skarpe og rene.
Omhyggeligt vedligeholdt værktøj med skarpe
skær sætter sig ikke så ofte fast og er lettere at
styre.
g) Brug elværktøj, tilbehør, udskiftelige dele osv.
iht. disse anvisninger. Tag hensyn til arbejds-
betingelserne og det arbejde, der skal udfø-
res. Anvendelse af elværktøj til andet end de
tiltænkte anvendelsesområder kan føre til farlige
situationer.
5. Anvendelse og behandling af det
genopladelige værktøj
a) Oplad kun batterierne i opladere, som produ-
centen har anbefalet. Hvis der bruges andre
genopladelige batterier til opladeren, end dem
opladeren er beregnet til, er der fare for brand.
b) Brug kun genopladelige batterier, der er
beregnet til elværktøj. Anvendelse af andre
genopladelige batterier kan medføre person-
skader og brandfare.
c) Når det genopladelige batteri ikke benyttes,
skal det holdes borte fra kontorclips, mønter,
nøgler, søm, skruer eller andre små metal-
genstande, som kan forårsage en kortslutning
mellem kontakterne. En kortslutning mellem det
genopladelige batteris kontakter kan medføre
forbrændinger og brand.
d) Ved forkert anvendelse kan der trænge væske
ud af det genopladelige batteri. Undgå
kontakt med denne væske. Skyl efter med
vand, hvis du alligevel kommer i kontakt med
væsken. Hvis væsken kommer i øjnene, skal
du søge læge. Batterivæske, der løber ud, kan
medføre hudirritationer eller forbrændinger.
FORSIGTIG! EKSPLOSIONSFARE!
Oplad aldrig batterier, der ikke er
beregnet til det.
Beskyt det genopladelige batteri
mod varme på grund af f.eks. ved-
varende solstråler, ild, vand og fugt.
Fare for eksplosion.
6. Service
a) Lad kun en kvalificeret reparatør reparere dit
elværktøj og kun med originale reservedele.
Derved garanteres det, at elværktøjets sikker-
hed bevares.