Parkside PTK 1700 A1 User manual

 
TABLE SAW
Operation and Safety Notes
Original operating instructions
3

BBORDRUNDSAV
Brugs- og sikkerhedsanvisninger
Original betjeningsvejledning
PTK 1700 A1
 
ΕΠΙΤΡΑΠΕΖΙΟ ΔΙΣΚΟΠΡΙΟΝΟ
Υποδείξεις χειρισμού και ασφαλείας
Πρωτότυπες Οδηγίες χρήσης
  
TISCHKREISSÄGE
Bedienungs- und Sicherheitshinweise
Originalbetriebanleitung
Anleitung_4340686:_ 07.06.2010 15:59 Uhr Seite 1

TABLE SAW
 
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
 
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις
λειτουργίες της συσκευής.
  
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit
allen Funktionen des Gerätes vertraut.
GB/CY Operation and Safety Notes Page 12
DK Brugs- og sikkerhedsanvisninger Side 31
GR/CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 50
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 71
BORDRUNDSAV
ΕΠΙΤΡΑΠΕΖΙΟ ΔΙΣΚΟΠΡΙΟΝΟ TISCHKREISSÄGE
Anleitung_4340686:_ 07.06.2010 15:59 Uhr Seite 2

TABLE SAW BORDRUNDSAV
ΕΠΙΤΡΑΠΕΖΙΟ ΔΙΣΚΟΠΡΙΟΝΟ TISCHKREISSÄGE
1
11
12
13
2 3
1
2
11 89
17
16
4
5
3
234 5 6 7
8
9
10
3
Anleitung_4340686:_ 07.06.2010 16:00 Uhr Seite 3

7
6
5
4
20
18 abcr
21 22 23 24 t s
19
18
19
20
21
22
ba
c
a
c
b
ba
a
c
c
4
Anleitung_4340686:_ 07.06.2010 16:01 Uhr Seite 4

89
12
11
10
14
14 14
24
14 14 15 25 26 u
18
18
b
15
c
d
n
38
23
39
d
u
d
u
5
Anleitung_4340686:_ 07.06.2010 16:02 Uhr Seite 5

14
13
16
1817
15
25
a
cab
c
ab
c
c
a
26
27
29 6
28
4
2
26
2
27
3
3
16
v
29
6
Anleitung_4340686:_ 07.06.2010 16:04 Uhr Seite 6

20
19
2423
21
max. 3-5 mm
rs
ff7 ff
7
5430
eeh
22
11 89
7
Anleitung_4340686:_ 07.06.2010 16:04 Uhr Seite 7

26
25
3029
27
j jk12 k
12 12
31 31
55
ee
7
f
5
7
f
28
12
l7
31
e
m
7
45°
7
e
8
Anleitung_4340686:_ 07.06.2010 16:05 Uhr Seite 8

32
31
3635
33 5
p
e
13
33
34 35 36 37
z
ef
13
33
eh
f
37
34
32
32
5
13 wf
q12
o
o
9
Anleitung_4340686:_ 07.06.2010 16:06 Uhr Seite 9

38
37
4241
39
7
2
1
4
5
5
—
—
+
+
7
40
35
2
17
10
Anleitung_4340686:_ 07.06.2010 16:07 Uhr Seite 10

44
43
e
13
11
Anleitung_4340686:_ 07.06.2010 16:07 Uhr Seite 11

The reprinting or reproduction by any other
means, in whole or in part, of documentation
and papers accompanying products is
permitted only with the express consent of the
ISC GmbH. Subject to technical changes
Table of contents: Page
1. Introduction .............................................................................14
2. Safety information ...................................................................14-19
3. Layout .....................................................................................19
4. Items supplied.........................................................................19-20
5. Intended use ...........................................................................20
6. Technical data.........................................................................20-21
7. Before starting the equipment .................................................21
8. Assembly ................................................................................22-23
9. Operation ................................................................................23-25
10. Functions ................................................................................26-27
11. Replacing the power cable......................................................27
12. Cleaning, maintenance, storage, transport
and ordering spare parts .........................................................27
13. Disposal and recycling ............................................................28
14. Declaration of conformity ........................................................29
15. Guarantee certificate...............................................................30
GB/
CY
12
Anleitung_4340686:_ 07.06.2010 16:07 Uhr Seite 12

“CAUTION - Read the operating instructions to reduce the risk of injury”
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Wear a breathing mask.
Dust which is injurious to health can be generated when working on wood and other
materials. Never use the tool to work on any materials containing asbestos!
Wear safety goggles.
Sparks generated during work or splinters, chips and dust emitted by the equipment
can cause loss of sight.
Wear gloves.
You must wear gloves at all times when handling saw blades.
Important. Risk of injury.
Never reach into the running saw blade.
Explanation of the symbols on the machine

GB/
CY
13
Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 13

GB/
CY
14
1. Introduction
 Important.
When using the equipment, a few safety
precautions must be observed to avoid injuries
and damage. Please read the complete
operating instructions and safety information
with due care. Keep these operating
instructions in a safe place so that the
information is available at all times. If you give
the equipment to any other person, hand over
these operating instructions and the safety
information as well. We cannot accept any
liability for damage or accidents which arise
due to a failure to follow these instructions and
the safety information.
2. Safety information
 CAUTION
Read all the safety information and
instructions. Any errors made in following the
safety information and instructions may result in
an electric shock, fire and/or serious injury.
Keep all safety information and instructions
in a safe place for future use.
2.1 General safety information on electric
power tools
Important. The following safety precautions
must be taken when using electric power
tools in order to protect the user from
electric shocks and the risk of injury and
fire. Read and follow these instructions
before using the equipment.
1. Keep your work area tidy
Untidy work areas can result in accidents.
2. Check the ambient conditions
Do not expose electric tools to rain. Never
use electric power tools in damp or wet
locations. Provide good lighting. Do not use
electric power tools near flammable liquids
or gases.
3. Protect yourself against electric shocks
Avoid bodily contact with earthed parts, e.g.
pipes, radiators, cookers and refrigerators.
4. Keep children away
Do not allow other persons to touch the tool
or cable, keep them away from your work
area.
5. Keep your electric power tools in a safe
place
Unused tools must be stored in a dry,
locked room out of children’s reach.
6. Do not overload your tools
They will work better and more safely within
their specified capacity range.
7. Use the right tools
Do not use tools or attachments which are
too weak for heavy duty work.
Never use tools on jobs for which they are
not intended; for example, do not use a
hand-held circular saw to fell trees or lop off
branches.
8. Wear suitable work clothes
Never wear loose fittings clothes or jewelry.
They may get caught in moving parts.
Rubber gloves and non-slip shoes are
recommended when working outdoors.
Wear a hair net if you have long hair.
9. Wear safety goggles
Use a dust mask when working on dusty
jobs.
10. Do not use the cable for purposes other
than that for which it is designed.
Do not carry the equipment by the cable
and do not use the cable to pull the plug out
of the socket. Protect the cable from heat,
oil and sharp edges.
11. Secure the workpiece
Use clamps or a vise to secure the
workpiece. This is safer than using your
hand and also enables you to operate the
machine with both hands.
12. Do not overstretch
Avoid abnormal working postures. Make
sure you stand squarely and keep your
balance at all times.
13. Take care of your tools
Keep your tools sharp and clean in order to
work well and safely. Follow the
maintenance information and the
instructions for changing tools. Check the
power plug and cable on a regular basis
and have them replaced by an authorized
specialist if they are damaged. Check the
Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 14

GB/
CY
15
extension cable regularly and replace it if
damaged. Keep handles dry and free from
oil and grease.
14. Pull out the power plug
When tools are not in use, before starting
any maintenance work or when changing
attachments such as saw blades, drill bits
and all kinds of mounted tools.
15. Always remove keys and wrenches after
use
Always check that keys, wrenches and
other adjusting tools have been removed
before you switch on the equipment.
16. Avoid unintentional starting
Never carry a tool with your finger on the
switch button while the tool is connected to
the power supply. Make sure that the switch
is turned off when connecting the tool to the
power supply.
17. When using an extension cable
outdoors
Check that it is approved for outdoor duty
and is marked accordingly.
18. Be alert at all times
Watch what you are doing. Use common
sense when working. Never use the tool
when you are distracted.
19. Check your tool for damage
Before using the tool again, check the
safety devices or any slightly damaged
parts to ensure that they are in good
working order. Check that the moving parts
are working correctly, that they do not jam,
and that no parts are damaged. Make sure
that all parts are fitted correctly to ensure
that the equipment remains safe to use.
Unless otherwise stated in the operating
instructions, damaged guards and parts
have to be repaired or replaced by a
customer service workshop. Damaged
switches have to be replaced by a customer
service workshop. Never use an electric
power tool with a switch that cannot be
turned on and off.
20. Important.
For your own safety you must only use the
accessories and additional units listed in the
operating instructions or recommended or
specified by the manufacturer. The use of
mounted tools or accessories other than
those recommended in the operating
instructions or catalog may place your
personal safety at risk.
21. Repairs may only be carried out by a
qualified electrician
This electric power tool complies with the
pertinent safety information. Repair work
must only be carried out by a trained
electrician, otherwise the equipment may
cause accidents.
22. Connect up the dust extraction system
If there are provisions for connecting up a
dust extraction system, make sure that such
a system is fitted and in use.
2.2 Special safety information
2.2.1 Safety precautions
■Blades that are deformed or cracked must
not be used.
■Change a worn out table insert.
■Use only blades which are recommended
by the manufacturer and comply with EN
847-1. When changing the blade, make
sure that the cutting width is not smaller and
the saw plate not bigger than the thickness
of the splitter.
■Make sure that the chosen blade is suitable
for the material that is to be cut.
■If necessary, wear suitable personal
protection equipment. This could consist of:
- Ear-muffs to reduce the risk of damaging
your hearing
- A breathing mask to reduce the risk of
inhaling hazardous dust
- Always wear gloves when handling saw
blades and rough materials.
Whenever practicable, saw blades must be
carried in a container.
■Circular saws have to be connected to a
dust collecting device when used to saw
wood. The following can have an influence
on dust development:
- Worn, damaged or cracked saw blades
- Recommended capacity of the vacuum
extraction system: 20 m/s
- Proper guidance of the workpiece
■Blades made of high-alloy high-speed steel
(HSS) must not be used.
■Keep the push stick or handle for a push
Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 15

GB/
CY
16
block at the machine at all times, even when
you are not using them.
2.2.2 Safety information on the laser
Important:
Laser radiation
Do not look into the beam
Laser class 2
Protect yourself and your environment from
accidents by taking the appropriate
precautionary measures.
■Do not look directly into the laser beam with
the naked eye.
■Never look directly into the laser path.
■Never direct the laser beam at reflecting
surfaces or persons or animals. Even a low
output laser beam can inflict injury on the
eye.
■Caution: It is vital to follow the work
procedures described in these instructions.
Using the equipment in any other way may
result in hazardous exposure to laser
radiation or radioactive contamination.
■Never open the laser module.
2.2.3 Safety information on the batteries
Use of the batteries
■Ensure that the ON/OFF switch for the laser
(35) is set to its “0” position before you fit
the batteries.
■Inserting the batteries when the laser is
switched on can cause accidents.
■If the equipment is not used correctly the
batteries may leak. Avoid contact with the
battery fluid. If you come into contact with
battery fluid, clean the affected body part
with running water. If you get battery fluid in
your eyes, seek immediate medical
assistance.
■Leaked battery fluid can cause skin irritation
and acid burns.
■Never expose the batteries to excess heat
such as sunshine, fire or similar.
■Never recharge batteries that are not
suitable for recharging. There is a risk of
explosion!
■Keep batteries away from children, do not
short circuit batteries or disassemble.
■Seek a doctor’s advice immediately if a
battery is swallowed.
■If necessary, clean the contacts on the
battery and equipment before inserting the
batteries.
■Ensure that you insert the batteries the right
way round.
■Remove flat batteries immediately from the
equipment. There is an increased risk of
leakage.
■Always change all batteries in one go.
■Insert only batteries of the same type, do
not use different types of batteries or used
and new batteries together.
■Make sure that the equipment is switched
off after use.
■Remove the batteries if the equipment is not
used over a longer period.
2.2.4 Maintenance and service
■The following conditions can have an
influence on noise impact on the operator:
- Type of saw blade (e.g. saw blades
designed to reduce noise development)
- Material of the workpiece
- The force with which the workpiece is
pushed against the saw blade
■Faults on the machine or its guards, safety
devices and blade must be reported to the
person in charge of safety as soon as they
are discovered.
2.2.5 Safe operation
■Use a push stick or the handle with a push
block to feed the workpiece safely past the
saw blade.
■Use the splitter and set it correctly.
■Use the upper blade guard and set it to the
correct position.
■Do not cut rebates or grooves without fitting
a suitable guard, e.g. a tunnel-type guard,

Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 16

GB/
CY
17
over the saw table.
■Circular saws must not be used for slotting
jobs (cutting grooves which end in the
workpiece).
■Use only blades whose permissible
maximum speed is not lower than the
maximum spindle speed of the bench-type
circular saw and of the material to be cut.
■Use only the transport devices to move the
equipment. Never use the guards for
handling or moving the equipment.
■While you are moving the machine it is best
to cover the top part of the blade, e.g. with
the guard.
■Secure long workpieces against falling off at
the end of the cut (e.g. with a roller stand
etc.)
2.2.6 Additional instructions
■Give these safety instructions to all persons
who work on the machine.
■Do not use this saw to cut fire wood.
■Do not use this saw to cross-cut
roundwood.
■Caution! Hands and fingers may be injured
on the rotating saw blade.
■The machine is equipped with a safety
switch to prevent it from being switched on
again accidentally after a power failure.
■Before you use the machine for the first
time, check that the voltage marked on the
rating plate is the same as your supply
voltage.
■If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw’s power consumption.
Minimum cross-section: 1 mm².
■If you use a cable reel, the complete cable
must be pulled off the reel.
■Check the power cable. Never use a faulty
or damaged power cable.
■Operators have to be at least 18 years of
age. Trainees of at least 16 years of age are
allowed to use the machine under
supervision.
■Keep your workplace clean of wood scrap
and any unnecessary objects.
■Persons working on the machine should not
be distracted.
■Note the direction of rotation of the motor
and saw blade.
■After you have switched off the motor, never
slow down the saw blade by applying
pressure to its side.
■Only fit blades which are well sharpened
and have no cracks or deformations.
■Never dismantle the machine’s safety
devices or render them inoperative.
■Faulty saw blades must be replaced
immediately.
■Never use saw blades which do not comply
with the data specified in these operating
instructions.
■It is imperative to make sure that all devices
which cover the saw blade are in good
working order.
■Important: It is prohibited to use this saw to
make plunge cuts.
■Damaged or faulty safety devices have to
be replaced immediately.
■The splitter is an important safety device.
Not only does it guide the workpiece, it also
prevents the kerf closing behind the blade
so that there is no kickback from the
workpiece. Note the thickness of the splitter.
The splitter should never be thinner than the
saw blade body or thicker than the width of
its kerf.
■The guard hood has to be lowered over the
workpiece for each cut.
■Be sure to use a push stick when slitting
narrow workpieces (smaller than 120 mm in
width).
■Never cut workpieces which are too small to
hold securely in your hand.
■It is imperative for the parallel stop to be
clamped on the right-hand side of the blade
whenever you cut narrow workpieces to
size.
■Always stand to the side of the saw blade
when working with the saw.
■Never load the machine so much that it cuts
out.
■Always press the workpiece firmly against
the saw table.
■Make sure that off-cuts do not catch on the
saw blade crown. Risk of catapulting!
■Refit all guards and safety devices
immediately after you have completed any
repairs or maintenance work.
Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 17

GB/
CY
18
■Be sure to observe the safety information
and operating and maintenance instructions
issued by the manufacturer, as well as the
dimensions listed in the Technical Data.
■It is imperative to observe the accident
prevention regulations in force in your area
as well as all other generally recognized
rules of safety.
■Note the information published by your
professional associations.
■Connect up the dust extraction system on
all jobs. The operator has to be informed
about the conditions with an influence on
dust development, e.g. the type of material
being processed (source and collection of
the dust), the significance of local
separation arrangements, and the correct
setting of hoods, baffle plates and guides.
■Operate the saw only with a suitable
vacuum extraction system or a standard
industrial vacuum cleaner.
■Never remove loose splinters, chips or
jammed pieces of wood when the saw
blade is running.
■To rectify faults or remove jammed pieces
of wood, always switch off the machine first.
Pull out the power plug!
■If the sawing gap is worn, replace the table
insert. - Pull out the power plug!
■This electric tool complies with the pertinent
safety regulations.
■Keep your work area clean and tidy. Untidy
and unlit work areas can result in accidents.
■Keep the tool out of the rain and away from
moisture. The ingress of water into an
electric power tool increases the risk of an
electric shock.
■Be careful, watch what you are doing and
use an electric tool sensibly. Never use the
tool if you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention when using the electric tool can
result in serious injuries.
■Do not use an electric power tool if the
switch is defective. An electric power tool
that cannot be switched on or off is
dangerous and must be repaired.
■Keep unused electric tools out of the reach
of children. Do not allow people who are not
familiar with the tool or who have not read
these instructions to use the tool. Electric
tools are dangerous if they are used by
inexperienced people.
■Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
■If the connection lead on the electric tool is
damaged, it must be replaced by a specially
prepared connection lead available from our
customer service organization.
■Have your tool repaired only by trained
personnel using only genuine spare parts.
This will ensure that your tool remains safe
to use.
■The equipment has to be set up where it
can stand securely.
■All covers and safety devices have to be
properly fitted before the equipment is
switched on.
■It must be possible for the blade to run
freely.
■When working with wood that has been
processed before, watch out for foreign
bodies such as nails or screws etc.
■Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted
and that the equipment’s moving parts run
smoothly.
■Use clamps to stop the workpiece slipping.
This is safer than using your hand.
■Follow the instructions for lubrication and
changing tools.
■Keep handles dry, clean and free from oil
and grease.
■Keep the push stick or handle for a push
block at the machine at all times, even when
you are not using them.
■Do not cut rebates or grooves without fitting
a suitable guard, e.g. a tunnel-type guard,
over the saw table.
■While you are moving the machine it is best
to cover the top part of the blade, for
example using a guard.
■Use only the transport handles punched into
both sides of the housing for transporting
the equipment.
■Never use the safety devices for handling or
transporting purposes.
Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 18

GB/
CY
19
Please keep these safety instructions in a
safe place
3. Layout
1. Saw bench
2. Saw blade guard
3. Extraction hose
4. Splitter
5. Saw blade
6. Table insert
7. Parallel stop
8. Hand wheel
9. Adjusting and locking grip
10. Base frame
11. ON/OFF switch
12. Chain bar
13. Cross stop
14. Bench width extension
15. Bench length extension
16. Extractor adapter
17. Push stick
18. Legs
19. Cross struts
20. Longitudinal struts
21. Center struts, short
22. Center struts, long
23. Rubber legs
24. Stability bar
25. Table support, short
26. Table support, long
27. Screw with wing nut
28. Oval hole in splitter
29. Countersunk head screws
30. Fixing screw
31. Eccentric lever
32. Groove
33. Knurled screw
34. Laser
35. Laser switch
36. Screws for battery compartment
37. Battery cover
38. /39. Fixing points
4. Items supplied
■Open the packaging and take out the
equipment with care.
■Remove the packaging material and any
packaging and/or transportation braces (if
available).
■Check to see if all items are supplied.
■Inspect the equipment and accessories for
transport damage.
■If possible, please keep the packaging until
the end of the guarantee period.
IMPORTANT
The equipment and packaging material are
not toys. Do not let children play with
plastic bags, foils or small parts. There is a
danger of swallowing or suffocating!
■Original operating instructions
■Saw table to preassembled, carbide-tipped
saw blade with 24 teeth
■Carbide-tipped saw blade with 48 teeth
■Saw blade guard
■Extraction hose
■Splitter with laser
■Batteries 1.5 V AAA (2x)
■Parallel stop
■Stop rail
■Cross stop
■Table width extension (2x)
■Table length extension
■Push stick
■Legs (4x)
■Cross struts (2x)
■Longitudinal struts (2x)
■Center struts, short (2x)
■Center struts, long (2x)
■Rubber feet (4x)
■Stability bar (2x)
■Table support, short (4x)
■Table support, long (2x)
Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 19

GB/
CY
20
Installation material
a) Washer M6 (52x)
b) Nut (38x)
c) Hex screw (52x)
d) Allen screw (6x)
n) Lock bolt (2x)
u) Washer M5 (6x)
v) Retaining clip
Tools
r) Open-ended wrench, size 10/13
s) Ring wrench, size 10/24
t) Allen key, size 4mm
5. Intended use
The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross
stop) of all types of timber commensurate with
the machine’s size. The equipment is not to be
used for cutting any type of round wood.
The equipment may only be used for the tasks it
is designed to handle. Any other use is deemed
to be a case of misuse. The user/operator and
not the manufacturer will be liable for any
damage or injuries of any kind caused as a
result of this.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be
voided if the equipment is used in commercial,
trade or industrial businesses or for equivalent
purposes.
The equipment is to be operated only with
suitable saw blades (saw blades made of HM
or CV) It is prohibited to use any type of HSS
saw blade and cutting-off wheel. To use the
equipment properly you must also observe the
safety information, the assembly instructions
and the operating instructions to be found in
these operating instructions.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment’s potential hazards. It is also
imperative to observe the accident prevention
regulations in force in your area. The same
applies for the general rules of health and
safety at work. The manufacturer will not be
liable for any changes made to the equipment
nor for any damage resulting from such
changes. Even when the equipment is used as
prescribed it is still impossible to eliminate
certain residual risk factors. The following
hazards may arise in connection with the
equipment’s construction and design:
■Contact with the saw blade in the
uncovered saw zone.
■Reaching into the running saw blade (cut
injuries).
■Kick-back of workpieces and parts of
workpieces.
■Saw blade fracturing.
■Catapulting of faulty carbide tips from the
saw blade.
■Damage to hearing if ear-muffs are not used
as necessary.
■Harmful emissions of wood dust when used
in closed rooms.
6. Technical data
AC motor 230-240 V ~ 50Hz
Power P S6 40% 1700 W
Idle speed n06500 min-1
Carbide saw blade Ø 250 x Ø 30
Number of teeth 24/48
Bench size 610 x 445 mm
Table width extension, left/right 608 x 250 mm
Table length extension, rear 435 x 320 mm
Cutting height max. 73 mm / 90°
63 mm / 45°
Infinite height adjustment 0 - 73 mm
Infinitely adjustable saw blade angle 0° - 45°
Dust extraction connector approx. diameter
36 mm
Weight with base frame, incl. all removable
parts approx. 28.5 kg
Anleitung_4340686:_ 07.06.2010 16:08 Uhr Seite 20