pastoe LANDSCAPE User manual

LANDSCAPE
design Joost van der Vecht 2012
pastoe
sleepboot 4
3991cn houten
the netherlands
[email protected]
www.pastoe.com
LANDSCAPE - wall mounted
LANDSCAPE - on a plinth

Components
Bolt Ø6x35 Bolt Ø6x20
Open compartment:
lamello
Open compartment:
connection part
Cap cover Cap cover hinge
Cap cover hinge
LANDSCAPE
design Joost van der Vecht 2012
A B C D
E F G
LANDSCAPE - on a plinth

Place the plinth at the desired position and adjust until level
using the adjustable legs.
Rotate the plinth so that the underside can be accessed and
place the body. Screw the body to the underside of the plinth
using the supplied bolts (A; L=35mm).
Place the second body in the same manner. Set the cabinet in the desired position.
Place the divider.
1 2
3 4
5
Place the body on the divider.
6
Secure the body from the cabinet underneath using the supplied
long bolts (A; L=35mm).
7
If this cabinet does not feature an open compartment, please go
on to step 11.
Place the back panel using the lamellos (F).
8 OPEN COMPARTMENT
A
A
A
A
A
A
AA
A
A
A
A
A
A
AF
A
Assembly instructions

screw the eccentric bolt into the side of the body and slide the
open compartment construction plank into position. Secure this
by tightening the minifix (H).
Place the next body on the divider. Place the eccentric bolts (G) in
the side and slide it against the construction plank. Secure by
tightening the minifix (H).
Secure the body from the body underneath using the long bolts
(A=35mm).
Place the top.
Secure the top from the bodies underneath using the supplied
short bolts (B=20mm). NOTE! Be sure to use the short bolts for
this. The long bolts could damage the top.
9 OPEN COMPARTMENT 10 OPEN COMPARTMENT
11 12
13
Adjust the fronts and, if needed, adjust the cabinet again using
the adjustable feet attached to the bottom bodies. Place the
cover caps (C).
14
15
A
B
B B
B B B
BB B B
BB
A
G
G
H
G
G
A
A
C
C
C
C
C
C
C
C
C
Assembly instructions

Components
G
Mounting plate
I
H
Plug and screw Ø5x45
J/K
Cover mounting part
Bolt Ø6x35 Bolt Ø6x20
B
A
Open compartment:
lamello
E
Open compartment:
connection part
F
Cap cover hinge
C/D
LANDSCAPE
design Joost van der Vecht 2012
LANDSCAPE - wall mounted

Secure the finishing top from the bodies underneath using the supplied short bolts (B; L=20mm).
NOTE! Be sure to use the short bolts for this. The long bolts could damage the top.
6
B
B B
B B B
BB B B
BB
B
B
B
B
Place the open compartment over the back panel by sliding it
over the connecting bolt.
3 OPEN COMPARTMENT2 OPEN COMPARTMENT
Place the following body. Tighten the minifixes.
4 OPEN COMPARTMENT
Secure the base from the bottom using the supplied bolts (B;
L=20mm).
5
B B
BB
D
D
F
FF
Secure the base from the bottom using the supplied bolts (B; L=20mm).
NOTE: The cabinet must be assembled so it can be mounted on the wall. The cabinet is to be mounted on the wall as a whole. To do so, please
follow the steps below.
To mount cabinets starting at 2.85m on the wall, three people will be required.
1
B
B B
B
B
B
B
B
F
If this cabinet does not feature an open compartment, please go on
to step 5.
Place the back panel using the lamellos(E).
Assembly instructions

Holes to be drilled in the facing side:
Drill the required holes in the wall according to the width of the body. Open compartments do not require (or have) hangers. Do take the width
into account when measuring out where to drill the holes.
7
60
40 4030 460 500 40 30
Body width1140mm
60
4030 430 40 30
Body width 570mm
60
4030 145 40 30
Body width 285mm
Open compartment width 285mm
Open compartment width 570mm
60
40 4030 300 375 40 30
Body width 855mm
14 40
60
16
Assembly instructions

H
G
I
Insert the plugs (H) into the drilled holes and secure the
Mounting plate (G) with the screws (I).
Hang the body with the hangers to the mounting rack. Make sure the
hangers are properly attached to the mounting rack.
Completely unscrew (in depth) the hangers with the help of the
screw (a).
The above hanger is used for bodies that are 85.5cm and 114cm
wide and are without a separation in the middle. Hollow this out as
well (screw c).
When mounting a body with drawers, all drawers must be removed.
To do this, push in the snapper underneath the drawer and pull the
drawer towards you.
89
11
10-2
10
a
b
ab
To ensure the body is level, use the screw (10a ,10d). Then slide
and push the cover (J, K) over the hangers
12
13
Place the drawers in the body. In order to do this, pull out the
drawer rails, place the drawers on these and push them back
into the body.
c
d
dc
Assembly instructions