PATIOJOY GYM06488 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Please give us a chance to make it right and do better！
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP!
USER’S MANUAL
3 Pcs Wicker Set
FLOOR AREA
2MX2M
ASSEMBLED BY 2 ADULTS
GYM06488

Contact Us!
Hardware inside
Do NOT return this item.
Contact our friendly customer service department for help first.
E-mail
Before You Start
Read each step carefully before starting. It is very important to ensure each step followed in
correct order, otherwise assembly difficulties may occur.
Most of board parts are labeled or stamped on the raw edges. Have a check to make sure all
parts are included.
Work in a spacious area, preferably on a carpet close to where the unit will be used.
Keep the handtools close at hand. Do not use power tools to assemble your furniture.
They may scratch or damage the parts.
02
[email protected]

Not actual size
Left Arm x 2 Right Arm x 2
Back x 2
Back Panel x 2
Footrest x 2
Bottom Foot x 8
Seat x 2
03
Seat Cushion x 2
Back Cushion x 2

Not actual size
04

Hardware List
Actual size
L4
M6 x 15mm
BOLT
BOLT
M32
M6 x 30mm
BOLT
M6 x 35mm
N12 O48
M6
WASHER
P1
4 x 4
ALLEN WRENCH
05

STEP 1
Aach the boom foot (G) to boom of each
Arm(B) by inserng bolts (M) with washers (O)
through the pre-drilled holes on the arm into the
pre-welded nuts on the boom foot.
Repeat step for the other side arm(A).
06
IMPORTANT:Do not ghten completely unl
assembly is completed.

STEP 2
(N) with washers (O) through the pre-drilled holes
Aach the seat(D) to the arm (B) by inserng bolts
on the seat into the pre-welded nuts on the arm.
Repeat step for the other side arm(A).
07

Aach the footrest(E) to the arm (A&B) by inserng
bolts (M) with washers (O).
STEP 3
Aach the back panel(F) to the arm (A&B) by
inserng bolts (M) with washers (O).
STEP 4
08

Aach the back (C) to the seat(D) by inserng
bolts (N) with washers (O).
Aach the back (C) to the arm (A&B) by
inserng bolts (L) with washers (O).
STEP 6
STEP 5
09

Tighten all the bolts with the allen wrench,
and turn the chair to the upright posion.
place the seat cushions(R) ,back cushion (Q) on the chair.
Your chair is now ready for use.
STEP 7
10

Maximum Loads
250 lbs
This item is only suitable within the specified maximum load-bearing. Heavier loads than
the indicated load capacity may cause instability, resulting in possible injuries.
11

Not actual size
12
Table Top x 1
Table Leg x 4
Resin Shelf x 1

Not actual size
13

Hardware List
Actual size
14
K 8
M6 x 10mm
BOLT
L4
M6 x 15mm
BOLT
O12
M6
WASHER
P1
4 x 4
ALLEN WRENCH

STEP 1
15
IMPORTANT:Do not ghten completely unl
assembly is completed.
Aach the leg(I) to the table top (H) by inserng
bolts (K) with washers (O).

STEP 2
16
Aach the leg(I) to the resin shelf (J) by inserng
bolts (L) with washers (O).

Tighten all the bolts with the allen wrench,
and turn the table to the upright posion.
Your table is now ready for use.
STEP 5
17

Maximum Loads
25 lbs
This item is only suitable within the specified maximum load-bearing. Heavier loads than
the indicated load capacity may cause instability, resulting in possible injuries.
18

Care and Maintenance
Please protect your outdoor furniture with a cover when not in use
since Long-term sunlight exposure will result in the damage on the
surface.
In addition to sunlight damage, wood and metal frame suffers when
exposed to extremes in temperature and humidity.
Proper care and cleaning at home will extend the life of your purchase.
Following these important and helpful tips will enhance your furniture
as it ages.
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary.
Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to
the finish.
Liquid spills should be removed immediately. Using a soft clean
cloth, blot the spill gently. Avoid rubbing.
Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
19