Patriot Lighting MH295 User manual

SKU Number:351-8777
1-LIGHT SEMI-FLUSH MOUNT
Model Number: MH295
PACKAGE CONTENTS
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
210607
HARDWARE CONTENTS
A
B
Mounting plate unit
X1
Mounting Screw
X2
Wire Connector
X3
Bolt Nut
X2
AA BB
CC DD
Note: Hardware not shown actual size.
Fixture Screw
X3
EE Vintage Bulb 60W
X1
FF

SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
●Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching off circuit breaker).
●Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact
any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury
or death from electric shock.
CAUTION
●All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
Contact your municipal building department to learn about your local codes, permits and/or inspections.
●Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician
before installation.
●Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use
a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means,
do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper
grounding methods as required by the local electrical code in your area.
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Slotted Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire
Cutters, Safety Glasses, Ladder, Wire Stripper.
Page 2 of 4
210607
ASSEMBLY INSTRUCTIONS
PREPARATION
Turn off the power at the fuse or circuit box.
1. Secure the mounting plate
unit(AA) to outlet box with
mounting screws(BB).
CC
A
AA
2
2. Pull out the source wires from
the outlet box, make wire
connections using wire
connectors(CC) as follows:
---Connect the black(hot) wire
from the fixture to the
black(hot) wire from the
power source.
---Connect the white(neutral)
wire from the fixture to the
white (neutral) wire from the
power source.
---Attach the fixture ground
wire(bare wire) to the mounting
plate unit(AA) with the green
ground screw, then connect
fixture ground wire to the
house ground wire with a wire connector(CC).
Carefully put the wires back into the outlet box.
1
Outlet Box
Green
Ground
Screw
BB
AA

4. Unscrew three fixture
screws(EE) from the
glass holder.
Attach the glass shade
(B) to the glass holder
and secure the glass
shade(B) with the
fixture screws(EE).
Page 3 of 4
210607
ASSEMBLY INSTRUCTIONS (continued)
Turn on the power at the
fuse or circuit box.
B
Glass Holder
FF
5
B
A
EE
4
The following parts are available for reorder if damaged or missing. Call our toll free at 1-800-887-6326.
Spare Parts List:
Assembly Kit
6411MM(1 SET)
Glass Shade
10267CG
B
3
3. Attach the canopy unit
(A) to the mounting
plate unit(AA), then
secure the canopy unit
(A) with two bolt nuts
(DD).
A
DD
AA
5. Install 1x60W medium
base vintage bulb(FF)
(included).
See relamping label at
socket area or
packaging for maximum
allowed wattage.
Fixture Screw
6425FS
Mounting plate unit
X1
Mounting Screw
X2
Wire Connector
X3
Bolt Nut
X2
AA
CC
BB
EE
DD
Vintage Bulb 60W
8072EB
FF

●To clean, turn off and wipe with a damp, non-abrasive cloth.
1) The light does not work:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
2) Fuse blows or circuit trips when light is turned on.
Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
CARE AND MAINTENANCE
TROUBLESHOOTING
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails
due to a defect in material workmanship within five (5) years from the date of original purchase, simply bring this
lighting fixture with the original sales receipt back to your nearest MENARDS retail store. At its discretion, PATRIOT
LIGHTING agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOT
LIGHTING product or part free of charge, within the stated warranty period, when returned by the original purchaser
with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does
not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to
persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary
from state to state.
R
R
R
R
Page 4 of 4
210607