PDi PD168-086 User manual

MODEL NUMBER:
PD168-086 & PD168-087
Document Number:
PD196-441R1
Installation Instructions
Page 1 of 2
Scope:
To Mount a PD168-086 J-Hook Mount to a 100x100 VESA, 100x200 VESA or 200x200 VESA TV in a PDI-179 or PDI-179AV wall
mount or to mount a PD168-087 J-Hook Mount to a 400x400 VESA TV in a PDI-179 or PDI-179AV wall mount.
Notes: The maximum capacity for this mount is 55 pounds. This mount cannot be used with a PDI-A55A TV, contact PDi using
information at the end of the document for questions. The TVs used in the graphics are used as reference only and are not included
with the kits listed.
Tool List:
1. P1 or P2 Phillips Screwdriver
2. 1/8” Hex Wrench
3. Safety Glasses/Goggles
Safety Steps:
1. Always wear safety glasses/goggles to prevent injury from debris.
2. Follow the installation/removal instructions for your existing products.
VESA Pattern Chart:
PDi TV
VESA Pattern (mm)
PDI-A24
100x100
PDI-A32
100x200
PDI-A43
200x200
PDI-A55
400x400
PD168-086 Installation Instructions
Bill of Material:
Item
Part Number
Description
QTY
1
PD168-086
J-Hook Articulating Mount
1
2
PDIPPHMSM6X110
Screw, Phillips Pan Head, M6-1 x 10mm
4
Procedure:
Step 1:
Mount the wall mount, PDI-179 or PDI-179AV, to the wall following the installation instructions included with the mount, (PD196-047
or PD196-396).
Step 2:
Attach the J-Hook mount, PD168-086, (#1) to the TV using four (4) screws, PDIPPHMSM6X110, for PDi TVs with a 100x200 VESA
or a 200x200 VESA as shown below. Be sure to align the correct slots on the J-Hook mount, PD168-086, with the VESA pattern on
the back of the TV, see reference dimensions below.
Note: Use customer supplied M-4 screws to mount a PDi TV with a 100x100 VESA.
Step 3:
Seat the J-Hook Mount, PD168-086, (#1) into the wall mount, PDI-179 or PDI-179AV, and tighten the pilfer proof screw.

MODEL NUMBER:
PD168-086 & PD168-087
Document Number:
PD196-441R1
Installation Instructions
Page 2 of 2
Step 4:
To adjust the tilt of the TV, support the weight of the unit and loosen both adjustment screws, one on each side shown below, using
a 1/8” hex wrench and adjust to the desired tilt. Tighten the adjustment screws down once the desired tilt has been achieved until
the TV remains in place.
Note: Only loosen the adjustment screw! Loosening the non-adjustment screws could cause the TV to fall.
PD168-087 Installation Instructions
Bill of Material:
Item
Part Number
Description
QTY
1
PD168-086
J-Hook Articulating Mount
1
2
PDIPPHMSM6X110
Screw, Phillips Pan Head, M6-1 x 10mm
4
3
PD181-881
Plate, Mounting, 400 x 400 VESA, Right
1
4
PD181-882
Plate, Mounting, 400 x 400 VESA, Left
1
5
PDIFW10
Washer, Flat, #10
4
6
PDINILN1032
Nut, Nylok, #10-32
4
7
PDIPPHMSM8X20
Screw, Phillips Pan Head, M8-1.25 x 20mm
4
Procedure:
Step 1:
Attach the mounting plates, PD181-881 (#3) and PD181-882 (#4), to the back of the TV and attach to the TV with four (4) screws,
PDIPPHMSM8X20, (#7).
Step 2:
Attach the J-Hook mount, PD168-086, (#1) to the mounting plates, PD181-881 (#3) and PD181-882 (#4), using four washers,
PDIFW10, (#5) and four (4) nuts, PDINILN1032, (#6) as shown. Once this is complete, follow steps 3 and 4 above.
Limited Warranty
PDi Communication Systems Inc., (“PDi”) standard warranty information is found at PDiarm.com. For information regarding
authorized servicing and all other information pertaining to this warranty, please contact PDi COMMUNICATION SYSTEMS, INC. at
40 Greenwood Ln, Springboro, Ohio 45066 or phone [phone] and ask for the PDi ProServices team.