Vivo STAND-V102K User manual

Dual Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102k
SKU: STAND-V102K
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
d(x2)
VESA Plate
c(x1)
Swivel Arm
a(x1)
Pole
e(x3)
M5x14
f(x2)
Nut
b(x1)
Weighted Base
g1 (x1)
Wire Clip
g2 (x4)
Wire Clip
i(x8)
M4x12
h(x1)
Allen Wrench
Set
k (x8)
M4 Spacer
j(x8)
M4x30
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD
OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

3
ASSEMBLY STEPS
STEP 1
Install the pole (a) to the base (b) using M5x14 bolts (e).
Tighten with the small Allen wrench (h).
TOOLS NEEDED
Phillips
Screwdriver Drill
22 lbs
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
PER ARM
a
e
b

4
STEP 2
Slide swivel arm (c) down onto the pole and tighten the bolt with large Allen wrench (h). Attach the
wire clips (g1, g2) to the pole and swivel arm.
STEP 3
OPTION A: Flat Back Monitor
Attach the VESA plates (d) to the monitors using M4x12 thumb bolts (i).
NOTE: Hand tighten screws to avoid stripping the plastic screw heads.
c
h
g1
g2
i

5
STEP 3 (Continued)
OPTION B: Curved Back TV
Attach the VESA plates (d) to the monitors using M4 spacers (k) and M4x30 bolts (j). Tighten with a
Phillips screwdriver.
STEP 4
Slide the monitors onto the heads of swivel arm and install the security nuts (f). Make sure the
security nuts are installed before you rotate the monitors.
k
j
f

6
STEP 5
Tighten the bolt on the side of the tilt joint with the medium Allen wrench (h) to fix the tilt angle. To level
the monitors, remove the security nut and turn the bolt with the small Allen wrench (h) to raise or lower
the monitor. Replace nut aer the adjustment.
h
Fix the tilt angle
Ignore this step if
monitors are level
h

7
STEP 6
Use the medium Allen wrench (h) to adjust swivel joints if needed. Manage cables and store the
Allen wrenches (h) in wire clip (g1) for future use.
CAUTION: To prevent tipping, please be careful not to extend the arms too far forward or backward.
h
g1

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303