PDR MDWM150 User manual

Model
MDWM150 MONITOR DISPLAY WALL MOUNT
To ensure the correct usage, please read and follow the instruction manual thoroughly. Please store the instructions in a safe place for future reference.
3. MOUNT THE MONITOR ASSEMBLY TO THE WALL
Fig 6
1
4
Special techniques are necessary for installation of the panel display mount.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Projector wall mounting application fig 2
All PDR mounts and adapters carry a limited lifetime warranty from ship date against defects in material and workmanship.
Check the PDR website for details @ www.PDRmounts.com We are not liable for improper installation that results in
damage to mounts, adapters or presentation equipment.
Mounts by
A division of David Engineering & Mfg. Inc.
!Suitable for displays with 75mm & 100mm
vesa hole pattern
!Simple to adjust no tools required
!Quick monitor removal with exclusive
“Bayonet slide system”
Features
Thank you for purchasing the PDR monitor mount .
Place the monitor assembly into the bayonet slots on the mounting plate ( small end into large end) engages fig 6.
slide the unit upwards and out.
To remove,
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to
withstand the weightof both the monitor and the mount.
Fully tighten all of the mounting screws as specified in the instructions.
Mounting hardware
Wall anchors 4 pcs
Monitor mounting screw 4 pcs
Bayonet plate
Rev 062105

1 FASTENING THE MOUNTING PLATE TO THE WALL
Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any
.
.
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the monitor mount
.
Use the specified screws in the specified places and tighten firmly. Failure to do this could cause injury if the monitor.
could result with injury due to the monitor mount falling..
.
NOTE: Do not over tighten the bracket mounting screws as damage to the monitors internal mounting threads could occur.
C A U T I O N : I N S T A L L A T I O N O F U N I T I S T O B E C A R R I E D O U T B Y Q U A L I F I E D T E C H N I C I A N S O N L Y. I N S T A L L I N
A N A P P R O P R I A T E L O C A T I O N B Y C H E C K I N G T H E S T R U C T U R E A N D D U R A B I L I T Y F O R S A F E T Y A N D
A C C I D E N T P R E V E N T I O N .
INSTALLATION LOCATION
water is possible. These can result in fire or electric shock.
.
.
falling. .
mount falls. .
Do not alter any of the parts. Do not use broken parts. This
.
Note:
.
3
2
CAUTION
WARNING
WARNING Locate the best viewing angle for the monitor, and using the 4 wall anchors supplied, attach the mounting plate
to the wall. Place the narrow end of the plate facing downward. Alternate hardware may be required if attaching
to a solid surface.. See fig 3 and fig 4
The wall where the mount is to be installed must be capable of long-term support of the
total load of the monitor and mount. Measures should be taken to ensure sufficient
strength to withstand the force of earthquakes , vibrations and other external forces.
Incorrect installation can cause the monitor mount to fall and cause injury.
Total load of the mount ( monitor + Mount)
Maximum weight - 20 Lbs ( 10Kg.)
2 ATTACH THE MOUNT TO THE MONITOR
Fig 5
Fig 4
Lay the monitor on a soft surface ,face down, and attach the mount using 75mm or 100mm VESA hole
pattern and the 4 screws supplied. See fig 5 ( note top of monitor)
Mounting surface
½”wall board
Mounting plate Wall anchors
Mo u nt i ng s cre ws
Top of Monitor
75mm & 100mm
Vesa hole pattern
Mounting plate