Pearl TURBOMAX HD User manual

17" PRO
BUFFERS
heavy-duty
floor
machineS
owner’S/operator’Smanual
Caution! Read Safety and General In truction carefully before u ing for the fir t time.
RE . 1
Pearl Abrasive Co. FLOOR buffer
Oper tion l C re l Service
#HEX1BFRHD
#HEX1BFRHDI
1-1/2 HP Sealed Induction,
Du l C p citor AC Motor
nd SDP (Severe Duty
Pl net ry)
1-1/2 HP Induction,
Du l C p citor AC Motor
nd SDP (Severe Duty
Pl net ry)
All manuals and user guides at all-guides.com
all-guides.com

– 2–
WHEN THE MACHINE IS DELIVERED
Check the carton carefully for signs of rough handling.
Remove the machine from the carton. If the machine is
damaged, notify the carrier IMMEDIATELY and request an
inspection. Be sure to keep the carton, packing inserts,
packing lists and carrier’s receipt until the inspector has
verified your claim.
Pearl’s liability ceases when the carrier picks up the
shipment but our customer service staff will be glad to
furnish any information needed in connection with the
claim and will expedite repair of the machine.
BEFORE OPERATING THE
MACHINE
Read the manual carefully and completely before
attempting to operate the unit. This manual has important
information for the use and safe operation of the machine.
eep this manual handy at all times. This machine will
assure years of satisfactory service if operated and
maintained according to recommendations in this manual.
If additional information is needed, please contact: 800-
969-5561
All information and specifications printed in the manual
and parts list are current at the time of printing; however,
because of Pearl’s policy of continual product
development, we reserve the right to make changes at any
time without notice.
WARNING! To reduce the risk of fire,
electric shock or injury:
• Do not operate the machine unless trained and
authorized.
• Do not leave the machine when plugged in. Unplug
from the outlet when not in use, before servicing, and
when changing the brushes or pads.
• Use indoors only.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Do not bypass or defeat the safety “lock-out lever.”
• The machine was designed for use as per instruction
and recommendations written in this manual. Any
deviation from its proper use or purpose and the
consequential damage that may occur is the sole
responsibility of the end user.
• Do not use with damaged cord or plug. If the machine
is not working as it should, or it has been dropped,
damaged, left outdoors or dropped into water, return it
to an authorized service center.
• Do not pull or carry by cord, use cord as handle, close a
door on the cord or pull cord around sharp edges or
corners. Do not run machine over cord. eep cord
away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Make sure the machine is plugged into an electrical
outlet with the same voltage and frequency rating as
shown on the nameplate of the machine. Do not
attempt to plug a 115- volt machine into a 230- volt
outlet.
• Do not immerse or use this machine in standing water.
Such use can cause electric shock.
• eep the electrical supply cord from contacting the
rotating brush or drive block.
• Do not expose machine to freezing temperatures.
• To avoid electric shock, do not expose the unit to rain.
Store indoors only.
• Connect to a properly grounded outlet only. See
“Grounding Instructions.”
• Turn off all controls before unplugging.
• When using an extension cord, use a 3 conductor
grounding cord, 12 gauge wire or heavier. Do not use
more than 25’ extension cord.
• Do not put any object into openings. Do not use with
any opening blocked. eep free of dust, lint, hair and
anything that may reduce air flow.
• Do not operate machine in flammable or explosive
areas.
• All servicing of Pearl’s equipment should be performed
by Pearl authorized service center.
• eep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
• Use extra care when cleaning on stairs. When servicing
machine, use manufacturer’s supplied or approved
replacement parts.
FAILURE TO COMPLY WITH THE ABOVE WARNING
INSTRUCTIONS WILL VOID THE WARRANTY.
GROUNDING
INSTRUCTIONS
Machine must be grounded.
If it should malfunction or
breakdown, grounding
provides a path of least
Fig. 1
All manuals and user guides at all-guides.com

– 3–
resistance for electrical current to reduce the risk of electric
shock. This machine is equipped with a cord having an
equipment-grounding plug (Fig. 1). The plug must be
plugged into an appropriate outlet that is properly installed
in accordance with all local codes and ordinances. Do not
remove ground pin; if missing, replace plug before use.
PREPARING THE MACHINE FOR
OPERATION
Your floor machine will operate in a wide variety of hard
floors and carpet cleaning applications. Consult with your
local dealer or Pearl Customer Service to select the correct
accessories for the job you are going to perform.
HEXPLATE™, BRUSH, PAD DRIVER
INSTALLATION
Lock the handle in the upright
position and tip the machine back
so it rests on the handle and
wheels. Fit the three slots of the
clutch plate in the back of the brush
or pad driver over the three lugs of
the drive plate. Push it firmly into
position and turn it
counterclockwise until it locks in
place (Fig. 2).
To remove: Tip the machine back so it rests on the handle
and wheels. Turn the brush or pad driver clockwise until it
disengages and lifts off. Do not store the machine with the
brush or pad drivers installed.
PAD INSTALLATION
To install pad, tilt the machine back on wheels until machine
is resting on handle. Center the pad on the pad holder and
insert pad center lock by twisting clockwise. Make sure the
center lock is tight.
To remove: Twist the center lock counterclockwise.
SOLUTION TAN INSTALLATION
Position the tank in front of the
floor machine with the water
release lever of the tank resting
below the floor machine lever.
There should be enough room for
you to pull the tank lever without
accidentally pulling the floor
machine lever (Fig. 3). Attach the
tank to the machine using the two
“V” bolts already included on the
tank. (Fig. 4).
The base of the tank has a
solution hose connected to it on
one end. Insert the other end of
the solution hose in the motor
frame (Fig. 5).
MACHINE OPERATION
1. Install the pad driver and pad, brush or attachment.
2. Plug in machine.
3. Lower the handle to the desired operating position.
4. Place both hands on the handle grips with your fingers
around the on/off lever which extends from one side to
the other underneath the handle grips.
5. The safety “lock-out” lever is
located underneath the right side
handle grip and switch lever. To
unlock the “lock-out” lever, use
your right hand forefinger to press
the lever down toward the back of
the switch box (Fig. 6).
6. While still pressing the lever, pull
the on/off switch lever to start the machine, then
release the “lock-out” lever. The “lock-out” lever will
automatically engage when you release the on/off switch
lever.
TO MANEUVER YOUR FLOOR MACHINE
1. Raise the handle slightly and the machine will go to the
right. The higher you raise it, the faster it will go.
2. Lower the handle and the machine will go left. The more
you lower it, the faster it will go.
3. Practice on a smooth surface until you gain experience
in operating the unit.
TO RE-ADJUST THE HANDLE-LOC
MECHANISM
Unlock the handle and place it in the
upright position. Tighten the
adjusting nuts until there is a slight
drag when the handle is raised or
lowered (Fig. 7).
CLEAN UP & STORAGE
1. Unplug and wrap it under the cord hook and around
the left side handle grip. Clean the cord and inspect it
for cuts, gashes and loose prongs.
2. Wipe down the machine and store in clean dry place.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 7
Fig. 6
All manuals and user guides at all-guides.com

– 4–
REPLACEMENT PARTS LIST
All manuals and user guides at all-guides.com

– 5–
REPLACEMENT PARTS LIST
1 PAB11487 Power Cord, 14-3, 50 FT, SJTW 1
2 PA 11498 Grip 2
3 PAC11528 Screw, 10-32 X .25 in 1
6 PAD11496B Switch Box Cover, Black 1
7 PAH11493 Label, Safety, Floor Machine 1
8 PAC11529 Screw, 10-32 X .375 in 2
9 PA 11519 Lever Grip, Lockout, Black 1
10 PAC00278 Locknut, 10-32, Nylon, SS 1
11 PAD11494 Lockout Bracket 1
12 PAD11524 Spring, Lockout 1
13 PAC90007 Screw, 10-32 X .625 hillips, Truss Head, SS 1
14 PAC11491 Screw, 10-32 X 1 in, SS 1
15 PAD11479 Handle, Chrome, Floormachine 1
16 PAC00306 Roll Pin, .125 X 1.75 2
17 PAD11523 Spring, Trigger 2
18 PAD11495 Trigger, Zinc Plated 1
19 PA 11520 Lever Grip, Trigger, Black 2
20 PA11507A Assembled Locking Handle, Cord Hook 1
21 PAC11619 Allen Wrench, .31 in 1
22 PAD11497 Handle, Locking Clamp 1
23 PAC11538 Cap Nut, .31 in, Push-On 1
24 PAC00259 Washer, Slotted, Zinc 1
25 PAC11536 Spade Bolt, .375-16 X 4 in 1
26 PAD11507 Cord Hook Clamp 1
27 PAD11507-2 Cord Hook Body 1
28 PAC11558 Locknut, Black Oxide, Thin 2
29 PAC11502 Socket Cap Screw, .375-16 X 2.5 in 1
30 PAC11537 Dowel Pin, .31 X 1.5 in 1
31 PAC13101 Screw, Hex Cap, M14-2.0 1
32 PA 00674 Bushing, .50 in, Nylon 2
33 PAD11510 Axle, Floor Machine 1
34 PAD11482 Handle Brace, Right, Black 1
35 PAC00240 Washer, Shoulder, Nylon 6
36 PAC11559 Washer, .515 X .875 X .032 6
37 PAG11943 Wheel, 5 in Saturn 2
38 PAC02305 Cap Nut, .5in Push-on 2
39 PAC11501 Socket Cap Screw, .31 - 18 4
40 PAC00251 Lockwasher, .31, Split 4
41 PAE11477 Bumper, 17 in Floor Machine 1
42 PAD11485B Brush Cover, 17 in, Black 1
43 PA 11521 Spacer, Base, Floor Machine 4
44 PAD11483 Frame, Motor, Black 1
45 PAG11468 Motor W-Gearbox, 1.5 HP 1
46 PAD11481 Handle Brace, Left, Black 1
47 PAH10976-1 Label, UL STD 561-507 1
50 PAD11490B Drip Cover, Black 1
52 PAC11916 Screw, 10-32 X .375 Phillips 3
53 PAC13100 Nut, M14-2.0 Nylon Insert 1
54 PAB10734 Strain Relief, Handle 1
55 PAB11513 Cord, Handle, 14-3 SJTW 1
56 PAB11762 Terminal Lug, Nylon, Female 2
57 PAB11465 Switch, DPST, Pushbutton 1
58 PAB00177 Terminal Lug, Female, QD, .25 X .032 2
59 PAC00252 Washer, .375 in, Flat 1
60 PAC11541 Washer, .375 in, Star 1
61 PAB11518 Switch Insulation 1
62 PAC00284 Screw, 10-32 X .375 Ground 1
63 PAB00187 Cable Clamp, Nylon, .43 in. 1
64 AB00180-10-3 Ring Terminal, #10 Center 2
65 PAB11505 Strain Relief Nut, Metal 1
66 PAC11560 Washer, .93 ID X 1.5 OD 1
67 PAB11504 Strain Relief, Metal 1
68 PAH02548-2 Label, Important, Cord 1
PART NUMBER PART NAME QTY PART NUMBER PART NAME QTY
All manuals and user guides at all-guides.com

– 6–
REPLACEMENT PARTS LIST
All manuals and user guides at all-guides.com
all-guides.com

– 7–
REPLACEMENT PARTS LIST
1 PAB11487 Power Cord, 14-3, 50 FT, SJTW 1
2 PA 11498 Grip 2
3 PAC11528 Screw, 10-32 X .25 in 1
6 PAD11496B Switch Box Cover, Black 1
7 PAH11493 Label, Safety, Floor Machine 1
8 PAC11529 Screw, 10-32 X .375 in 2
9 PA 11519 Lever Grip, Lockout, Black 1
10 PAC00278 Locknut, 10-32, Nylon, SS 1
11 PAD11494 Lockout Bracket 1
12 PAD11524 Spring, Lockout 1
13 PAC90007 Screw, 10-32 X .625 hillips, Truss Head, SS 1
14 PAC11491 Screw, 10-32 X 1 in, SS 1
15 PAD11479 Handle, Chrome, Floormachine 1
16 PAC00306 Roll Pin, .125 X 1.75 2
17 PAD11523 Spring, Trigger 2
18 PAD11495 Trigger, Zinc Plated 1
19 PA 11520 Lever Grip, Trigger, Black 2
20 PA11507A Assembled Locking Handle, Cord Hook 1
21 PAC11619 Allen Wrench, .31 in 1
22 PAD11497 Handle, Locking Clamp 1
23 PAC11538 Cap Nut, .31 in, Push-On 1
24 PAC00259 Washer, Slotted, Zinc 1
25 PAC11536 Spade Bolt, .375-16 X 4 in 1
26 PAD11507 Cord Hook Clamp 1
27 PAD11507-2 Cord Hook Body 1
28 PAC11558 Locknut, Black Oxide, Thin 2
29 PAC11502 Socket Cap Screw, .375-16 X 2.5 in 1
30 PAC11537 Dowel Pin, .31 X 1.5 in 1
31 PAC13101 Screw, Hex Cap, M14-2.0 1
32 PA 00674 Bushing, .50 in, Nylon 2
33 PAD11510 Axle, Floor Machine 1
34 PAD11482 Handle Brace, Right, Black 1
35 PAC00240 Washer, Shoulder, Nylon 6
36 PAC11559 Washer, .515 X .875 X .032 6
37 PAG11943 Wheel, 5 in Saturn 2
38 PAC02305 Cap Nut, .5in Push-on 2
39 PAC11501 Socket Cap Screw, .31 - 18 4
40 PAC00251 Lockwasher, .31, Split 4
41 PAE11477 Bumper, 17 in Floor Machine 1
42 PAD11485B Brush Cover, 17 in, Black 1
43 PA 11521 Spacer, Base, Floor Machine 4
44 PAD11483 Frame, Motor, Black 1
45 PA11476A HD Motor W-Gearbox, 1 .5 HP 1
46 PAD11481 Handle Brace, Left, Black 1
47 PAH10976-1 Label, UL STD 561-507 1
50 PAD11490B Drip Cover, Black 1
52 PAC11916 Screw, 10-32 X .375 Phillips 3
53 PAC13100 Nut, M14-2.0 Nylon Insert 1
54 PAB10734 Strain Relief, Handle 1
55 PAB11513 Cord, Handle, 14-3 SJTW 1
56 PAB11762 Terminal Lug, Nylon, Female 2
57 PAB11465 Switch, DPST, Pushbutton 1
58 PAB00177 Terminal Lug, Female, QD, .25 X .032 2
59 PAC00252 Washer, .375 in, Flat 1
60 PAC11541 Washer, .375 in, Star 1
61 PAB11518 Switch Insulation 1
62 PAC00284 Screw, 10-32 X .375 Ground 1
63 PAB00187 Cable Clamp, Nylon, .43 in. 1
64 AB00180-10-3 Ring Terminal, #10 Center 2
65 PAB11505 Strain Relief Nut, Metal 1
66 PAC11560 Washer, .93 ID X 1.5 OD 1
67 PAB11504 Strain Relief, Metal 1
68 PAH02548-2 Label, Important, Cord 1
PART NUMBER PART NAME QTY PART NUMBER PART NAME QTY
All manuals and user guides at all-guides.com

PEARL TURBOMAX BUFFERS • 12/15
GEORGIA • USA
3950 STEVE REYNOLDS BLVD.,
NORCROSS, GA 30093
ONTARIO • CANADA
375 IDO ROAD
ETERBOROUGH, ONTARIO K9J-6X7
CORPORATE OFFICE: SO. CALIFORNIA • USA
6832 E. SLAUSON AVENUE, COMMERCE, CA 90040-0031
562-927-5561 • FAX [phone]
Toll Free: 800-969-5561
www.pearlabrasive.com
ACCESSORIES (Option l)
Name (Qty.)
BUFVAC Dust
Containment System (1)
Part Number
BUFVAC1
Name (Qty.)
Solution Tank (1)
Part Number
BUFTNK03
All manuals and user guides at all-guides.com