Peavey CS 3000H User manual

CCSS33000000HH OOppeerraattiioonnss MMaannuuaall PPoowweerr AAmmpplliiffiieerr
For more information on other great Peavey products, go to your local Peavey dealer or online at www.peavey.com

2
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a ris of electric shoc to persons.
Intended to alert the user of the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
CCAAUUTTIIOONN::Ris of electrical shoc — DO NOT OPEN!
CCAAUUTTIIOONN::To reduce the ris of electric shoc , do not remove cover. No user serviceable parts inside.
Refer servicing to qualified service personnel.
WWAARRNNIINN::To prevent electrical shoc or fire hazard, do not expose this appliance to rain or moisture.
Before using this appliance, read the operating guide for further warnings.
Este símbolo tiene el propósito, de alertar al usuario de la presencia de “(voltaje) peligroso” sin
aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para
constituir riesgo de descarga eléctrica.
Este símbolo tiene el propósito de alertar al usario de la presencia de instruccones importantes sobre la
operación y mantenimiento en la información que viene con el producto.
PPRREECCAAUUCCIIOONN::Riesgo de descarga eléctrica ¡NO ABRIR!
PPRREECCAAUUCCIIOONN::Para disminuír el riesgo de descarga eléctrica, no abra la cubierta. No hay piezas útiles
dentro. Deje todo mantenimiento en manos del personal técnico cualificado.
AADDVVEERRTTEENNCCIIAA::Para evitar descargas eléctricas o peligro de incendio, no deje expuesto a la lluvia o
humedad este aparato Antes de usar este aparato, Iea más advertencias en la guía de operación.
Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur la présence d’une tension dangereuse
pouvant être d’amplitude suffisante pour constituer un risque de choc électrique.
Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur qu’il ou qu’elle trouvera d’importantes
instructions concernant l’utilisation et l’entretien de l’appareil dans le paragraphe signalé.
AATTTTEENNTTIIOONN::Risques de choc électrique — NE PAS OUVRIR!
AATTTTEENNTTIIOONN::Afin de réduire le risque de choc électrique, ne pas enlever le couvercle. Il ne se trouve à
l’intérieur aucune pièce pouvant être reparée par l’utilisateur. Confiez I’entretien et la réparation de
l’appareil à un réparateur Peavey agréé.
AAVVEERRTTIISSSSEEMMEENNTT: Afin de prévenir les risques de décharge électrique ou de feu, n’exposez pas cet
appareil à la pluie ou à l’humidité. Avant d’utiliser cet appareil, lisez attentivement les avertissements
supplémentaires de ce manuel.
Dieses Symbol soll den Anwender vor unisolierten gefährlichen Spannungen innerhalb des Gehäuses
warnen, die von Ausreichender Stär e sind, um einen ele trischen Schlag verursachen zu önnen.
Dieses Symbol soll den Benutzer auf wichtige Instru tionen in der Bedienungsanleitung aufmer sam
machen, die Handhabung und Wartung des Produ ts betreffen.
VVOORRSSIICCHHTT:: Risi o — Ele trischer Schlag! Nicht öffnen!
VVOORRSSIICCHHTT:: Um das Risi o eines ele trischen Schlages zu vermeiden, nicht die Abdec ung enfernen. Es
befinden sich eine Teile darin, die vom Anwender repariert werden önnten. Reparaturen nur von
qualifiziertem Fachpersonal durchführen lassen.
AACCHHTTUUNN::Um einen ele trischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gerät nicht dem
Regen oder Feuchtig eit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

3
IIMMPPOORRTTAANNTT SSAAFFEETTYY IINNSSTTRRUUCCTTIIOONNSS
WWAARRNNIINN::When using electrical products, basic cautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not bloc any of the ventilation openings. Install in accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being wal ed on or pinched, particularly at plugs, convenience receptacles, and the point
they exit from the apparatus.
11. Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your
plug‚ proceed as follows:
a) The wire that is colored green and yellow must be connected to the terminal that is mar ed by the letter E‚ the earth
symbol‚ colored green or colored green and yellow.
b) The wire that is colored blue must be connected to the terminal that is mar ed with the letter N or the color blac .
c) The wire that is colored brown must be connected to the terminal that is mar ed with the letter L or the color red.
12. Only use attachments/accessories provided by the manufacturer.
13. Use only with a cart, stand, tripod, brac et, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
14. Unplug this apparatus during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
16. Never brea off the ground pin. Write for our free boo let “Shoc Hazard and Grounding.” Connect only to a power
supply of the type mar ed on the unit adjacent to the power supply cord.
17. If this product is to be mounted in an equipment rac , rear support should be provided.
18. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in suscep-
tibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise
for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the
following permissible noise level exposures:
Duration Per Day In Hours Sound Level dBA, Slow Response
890
692
495
397
2100
1
1
⁄ 2 102
1105
1
⁄ 2 110
1
⁄ 4 or less 115
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the
ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure
is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is
recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be
protected by hearing protectors while this unit is in operation.
SSAAVVEE TTHHEESSEE IINNSSTTRRUUCCTTIIOONNSS!!

4
CCSS33000000HH PPoowweerr AAmmpplliiffiieerr
Congratulations on your purchase of the CS3000H power amplifier from Peavey—designed for years
of reliable, flawless operation under rigorous use. This amplifier offers the sonic superiority and
unsurpassed reliability for which Peavey is famous, while remaining surprisingly compact. Advanced
technology and extensive protection circuitry allow operation with greater efficiency into difficult
loads and power conditions. The DDDDTT™ (Distortion Detection) circuit ensures trouble-free operation
into loads as low as 2 oHms. The Distortion Detection circuits protect drivers and ensure that sonic
integrity is maintained, even in extreme overload conditions. Peavey’s high-efficiency design uses
tunnel-cooled heat sin s and variable speed DC fans. This cooling topology maintains a lower overall
operating temperature, resulting in longer output transistor life.
Although the Peavey CS3000H amplifier is quite simple to operate and is housed in ultra-strong steel
chassis, improper use can be dangerous. This amplifier is very high-powered and can put out high
voltages and sizable currents at frequencies up to 30 Hz. Always use safe operating techniques
when operating this amplifier.
FFOORR YYOOUURR SSAAFFEETTYY,, RREEAADD TTHHEE IIMMPPOORRTTAANNTT PPRREECCAAUUTTIIOONNSS SSEECCTTIIOONN,, AASS WWEELLLL AASS IINNPPUUTT,, OOUUTTPPUUTT,, AANNDD
PPOOWWEERR CCOONNNNEECCTTIIOONN SSEECCTTIIOONNSS..
··1199"" 22--ssppaaccee‚‚ rraacc--mmoouunnttaabbllee ddeessiiggnn
··ttuunnnneell--ccoooolleedd hheeaatt ssiinnss wwiitthh vvaarriiaabbllee ssppeeeedd DDCC ffaannss
··uullttrraa--ssttrreennggtthh sstteeeell cchhaassssiiss
··RRaammppUUpp™™ ssiiggnnaall ccoonnttrrooll
··33 ooppeerraattiioonnaall mmooddeess:: sstteerreeoo‚‚ ppaarraalllleell oorr bbrriiddggeedd--mmoonnoo
··ffrroonntt ppaanneell AACC ppoowweerr sswwiittcchh//cciirrccuuiitt bbrreeaaeerr
··aammpp ffuunnccttiioonn sswwiittcchh ffoorr ffuullll--rraannggee ooppeerraattiioonn oorr ccrroossssoovveerr hhiigghh//llooww ffrreeqquueennccyy oouuttppuuttss
··ttwwoo iinnddeeppeennddeenntt‚‚ aaddjjuussttaabbllee ccrroossssoovveerrss
··ttwwoo iinnddeeppeennddeenntt llooww ffrreeqquueennccyy ffiilltteerrss
··ffiivvee ffrroonntt ppaanneell LLEEDD iinnddiiccaattoorrss ppeerr cchhaannnneell:: AACCTTIIVVEE,, DDDDTT™™,, SSIIGGNNAALL‚‚ TTEEMMPP aanndd DDCC
UUnnppaacciinngg
Upon unpac ing, inspect the amplifier. If you find any damage, notify your supplier immediately. Only
the consignee may institute a claim with the carrier for damage incurred during shipping. Be sure to
save the carton and all pac ing materials. Should you ever need to ship the unit bac to Peavey
Electronics, one of its offices, service centers, or the supplier, use only the original factory pac ing. If
the shipping carton is unavailable, contact Peavey to obtain a replacement.
MMoouunnttiinngg
The CS3000H amplifier will mount in standard 19-inch rac s. Rear mounting ears are also provided for
additional support, which is recommended in non-permanent installations li e mobile or touring
sound systems. Because of the cables and connectors on the rear panel, a right angle or offset
screwdriver or hex ey will ma e it easier to fasten the rear mounting ears to the rails.
CCoooolliinngg RReeqquuiirreemmeennttss
The CS3000H amplifier uses a forced-air cooling system to maintain a low, even operating
temperature. Air is drawn into the amplifier by fans on the front panel, courses through the cooling
fins of the tunnel-configured channel heat sin s, and then exhausts through the rear and side panel
slots. If either heat sin gets too hot, its sensing circuit will open the output relay, disconnecting the
load from that particular channel. It is important to have an exhaust outlet at the bac of the amplifier
and enough space around the sides of the amplifier to allow the cooling air to escape. If the amp is
rac mounted, do not use doors or covers on the front of the rac ; the inta e air must flow without
resistance. If you are using rac s with closed bac s, ma e sure that there is one (1) standard rac
space opening for every three mounted power amplifiers.
EENNGGLLIISSHH
FFeeaattuurreess
DDeessccrriippttiioonn

5
OOppeerraattiinngg PPrreeccaauuttiioonnss
Ma e sure the mains voltage is correct and is the same as that printed on the rear of the amplifier.
Damage caused by connecting the amplifier to improper AC voltage is not covered by any warranty. See
the Connecting Power section for more information on voltage requirements.
NNoottee:: AAllwwaayyss ttuurrnn ooffff aanndd ddiissccoonnnneecctt tthhee aammpplliiffiieerr ffrroomm mmaaiinnss vvoollttaaggee bbeeffoorree mmaakkiinngg
aauuddiioo ccoonnnneeccttiioonnss.. AAllssoo,, aass aann eexxttrraa pprreeccaauuttiioonn,, hhaavvee tthhee aatttteennuuaattoorrss ttuurrnneedd ddoowwnn
dduurriinngg ppoowweerr--uupp..
Although the CS3000H amplifier has RRaammppUUpp™circuitry, which raises the signal level gradually after the
output relay closes, it is always a good idea to have the gain controls turned down during power-up to
prevent spea er damage if there is a high signal level at the inputs. Whether you buy or ma e them, use
good-quality connections, input cables and spea er cables, along with good soldering technique, to
ensure trouble-free operation. Most intermittent problems are caused by faulty cables.
Consult the Wire Gauge Chart (below) to determine proper gauges for different load impedances and
cable lengths. Remember that cable resistance robs amplifier power in two ways: power lost directly to
resistance (I2R loss), and by lowering the total load impedance. Also ma e sure the mode switch is
correctly set for the desired application. See Sections on SStteerreeoo, PPaarraalllleelland BBrriiddggeedd MMoonnoooperation for
more information.
WIRE GAUGE CHART
Cable Length
(In Feet)
Stranded Wire auge
(AW )
Power Loss into
8 ohms (%)
Power Loss into
4 ohms (%)
Power Loss into
2 ohms (%)
5 18 .79 1.58 3.16
16 .50 1.00 2.00
14 .31 .62 1.24
12 .20 .40 .80
10 .125 .25 .50
10 18 1.58 3.16 6.32
16 1.00 2.00 4.00
14 .62 1.25 2.50
12 .40 .80 1.60
10 .25 .50 1.00
40 18 8.00 12.60 25.20
. 16 4.00 8.00 1.60
14 2.50 5.00 10.00
12 1.60 3.20 6.40
10 1.00 2.00 4.00
8 .625 1.25 2.50
80 16 8.00 16.00 32.00
14 5.00 10.00 20.00
12 3.20 6.40 12.80
10 2.00 4.00 8.00

6
CCoonnnneeccttiinngg IInnppuuttss
Input connections are made via the 3-pin XLR (pin 2+) or 6.3 mm plug “Combi” connectors on the
rear panel of the amplifier. The inputs are actively balanced. Pinout and polarity of connection
cables should be configured correctly (refer to the rear panel of the unit). The input overload
point is high enough to accept the maximum output level of virtually any signal source.
CCoonnnneeccttiinngg OOuuttppuuttss
All models have two output (spea er) connections per channel. Cables can be connected with
banana plugs, spade lugs, or bare wire to the 5-way binding posts. The preferred connection
method is via the Spea on connectors. Pin connections are noted on the rear panel of the unit.
CCoonnnneeccttiinngg PPoowweerr
The CS3000H power requirements are rated at 1/8 power (typical music conditions) and 1/3
power (extreme music conditions). The maximum power current draw rating is limited only by the
front panel circuit brea er. Consult the specifications in this manual for figures on the current
that this amplifier will demand. Ma e sure the mains voltage is correct and is the same as that
printed on the rear of the amplifier. Damage caused by connecting the amplifier to improper AC
voltage is not covered by any warranty. Unless otherwise specified when ordered, Peavey
amplifiers shipped to customers are configured as follows:
North America: 120 VAC/60 Hz
Europe, Asia, Australia: 230/240 VAC/50 Hz
South America: 120 VAC/60 Hz or 240 VAC/50 Hz
SStteerreeoo
For stereo (dual channel) operation, turn the amplifier off and set the mode select switch to the
stereo position. In this mode, both channels operate independently of each other, with their
input attenuators controlling their respective levels. Thus, a signal at Channel A’s input produces
an amplified signal at Channel A’s output, while a signal at Channel B’s input produces an
amplified signal at Channel B’s output.
PPaarraalllleell
For parallel (dual-channel/single input) operation, turn the amplifier off and set the mode switch
in the parallel position; both amplifier channels are then driven by the signal at Channel A’s
input. No jumper wires are needed. Output connections are the same as in the stereo mode. In
the parallel mode, only Channel A’s input is active; Channel B’s is out-of-circuit. Both input
attenuators remain active, allowing you to set different levels for each channel. Power and other
general performance specifications are the same as in the stereo mode.
BBrriiddggeedd MMoonnoo
Both amplifier channels can be bridged together to ma e a very powerful single-channel
monaural amplifier. Use extreme caution when operating in the bridged mode; potentially lethal
voltage may be present at the output terminals. To bridge the amplifier, set the rear panel mode
select switch to the bridge position. Apply the signal to Channel A’s input and connect the
spea ers across the hot outputs (the “+” binding posts of Channels A and B).
Unli e the stereo and parallel modes, in which one side of each output is at ground, in the
bridged mode both sides are hot. Channel A’s side is the same polarity as the input. For proper
operation, both input attenuators must be in the same position. This eeps the load balanced
between the channel outputs. As in the parallel mode, only Channel A’s input is active. If an
output patch panel is used, all connections must be isolated from each other and from the panel.
The recommended minimum nominal load impedance in the bridged mode is 4 ohms (equivalent
to driving both channels at 2 ohms). Driving bridged loads of less than 4 ohms will activate the
DDT circuitry resulting in a loss of power, and may also cause a thermal overload.
OOppeerraattiioonn MMooddeess

7
AACC PPoowweerr SSwwiittcchh//CCiirrccuuiitt BBrreeaakkeerr ((11))
The CS3000H amplifier has a combination AC switch/circuit brea er on the front panel. If the switch
shuts off during normal use, push it bac to the ON position once. If it will not stay on, the amplifier
needs servicing.
IInnppuutt AAtttteennuuaattoorrss ((22))
Whenever possible, set the attenuators fully cloc wise to maintain optimum system headroom. The
input attenuator controls (one for channel A, one for channel B) located at the front panel adjust gain
for their respective amplifier channels in all modes. See the specifications at the end of this manual
for standard voltage gain and input sensitivity information.
When operating in the bridged mode, both attenuators must be in the same position so the spea er
load will be equally shared between the channels. See the section on BBrriiddggeedd MMoonnooOperation for
more information and precautions.
FFrroonntt PPaanneell IInnddiiccaattoorrss
The CS3000H features four front panel discreet LED indicators per channel: AACCTTIIVVEE, DDDDTT, TTEEMMPP
and DDCC. These LED indicators inform the user of each channel’s operating status and warn of
possible abnormal conditions. This amplifier also features two 10-segment bar graph indicators
per channel: SSIIGGNNAALL.
SSIINNAALL LLEEDD ((33))
This LED is at the bottom of the bar graph display and lights when its channel produces an output
signal of greater than 2 volts RMS or 50mV input with a 0 dB attenuation of the front panel nobs. It
is useful in determining whether a signal is reaching and being amplified by the amplifier. The 10-
segment graphs indicate the level of signal present.
DDCC LLEEDD ((44))
The DC LED lights to indicate that the channel’s output relay is open, disconnecting the spea er(s)
when the amplifier senses a DC voltage or subsonic high level signal at its output.
TTEEMMPP LLEEDD ((55))
The Temp LED lights to indicate that the channel’s output relay is open, disconnecting the spea er(s)
due to an overheating condition. Once the channel temperature has returned to safe operating
conditions the LED will turn off and the spea er(s) will be reconnected.
2
1
FFrroonntt PPaanneell
4 5 6 73

8
MMOODDEE SSeelleecctt SSwwiittcchh ((88))
The rear panel MODE Select Switch determines whether the amplifier is in stereo, parallel, or
bridged mono mode. Do not operate the Mode Select Switch with the amplifier powered on. See
the sections on Stereo and Bridged Mono Mode for more information.
AAMMPP FFUUNNCCTTIIOONN SSwwiittcchh ((99))
The rear panel AMP FUNCTION Select Switch determines whether the associated channel is
connected for full range operation or to the crossover high frequency or low frequency outputs.
CCRROOSSSSOOVVEERR AAddjjuussttmmeenntt KKnnoobb ((1100))
The CS3000H is equipped with two independent‚ two-way crossovers adjustable from 40Hz to 300
Hz. These crossover frequencies are appropriate for use with a subwoofer system. The output of
these crossovers is selected by the MODE switch and connected to the corresponding amplifier
channel. Frequencies above the nob setting will be connected to the corresponding channel
when the MODE switch is in the HIGH PASS position. Frequencies below the nob setting will be
connected to the corresponding channel when the MODE switch is in the LOW PASS position. The
FULL RANGE position bypasses the crossover.
LLOOWW CCUUTT AAddjjuussttmmeenntt KKnnoobb ((1111))
The CS3000H is equipped with two independent low frequency filters. These filters are adjustable
from 20Hz to 100Hz and are designed to reduce frequencies below those capable of being
produced by the loudspea ers, or to reduce room “rumble.” Frequencies below the nob setting
of the corresponding channel will be attenuated.
RReeaarr PPaanneell
8 9 10 11
12
13
DDDDTT LLEEDD ((66))
A channel’s DDT LED will light at the onset of clipping. If the LED’s are flashing quic ly and
intermittently, the channel is just at the clip threshold, while a steady, bright glow means the amp
is clip limiting, or reducing gain to prevent severely clipped waveforms reaching the loudspea ers.
See the Distortion Detection section for more information. During initial power up the DDT LED will
light indicating that the RampUp gain reduction circuitry is activated. This will prevent sudden
signal bursts when the spea er relays are closed.
AACCTTIIVVEE LLEEDD ((77))
The ACTIVE LED indicates that its channel’s output relay is closed and the channel is operational. It
lights under normal operation and remains on even when the channel is in Distortion Detection
(DDT) gain reduction. These are protection features which leave the output relay closed. If the
ACTIVE LED goes off, there is no signal at the output connectors.
14

9
LLOOWW CCUUTT SSwwiittcchh ((1122))
The LOW CUT switch is a recessed push switch used to defeat or engage the LOW CUT filter. Pushing
the switch to the in position will engage the filter.
HHIIHH PPAASSSS//FFUULLLL RRAANNEE OOUUTTPPUUTT CCoonnnneeccttoorr ((1133))
The HIGH PASS/FULL RANGE OUTPUT connector function is dependent on the setting of the
corresponding MODE switch. This connector allows patching the frequencies above the crossover nob
setting to a secondary amplifier. If the MODE switch is in the HIGH PASS position, the high frequency
portion of the crossover will be present at the connector. If the MODE switch is in the FULL RANGE or
LOW PASS position, the crossover will be bypassed and allow patching the full range signal to a
secondary amplifier.
LLOOWW PPAASSSS OOUUTTPPUUTT CCoonnnneeccttoorr ((1144))
The LOW PASS OUTPUT connector allows patching the frequencies below the crossover nob setting to
a secondary amplifier. This output remains at low frequencies independent of the MODE switch setting.
PPrrootteeccttiioonn FFeeaattuurreess
The CS3000H incorporates several circuits to protect both itself and loudspea ers under virtually any
situation. Peavey has attempted to ma e the amplifier as foolproof as possible by ma ing it immune to
short and open circuits, mismatched loads, DC voltage, and overheating. If a channel goes into the
Distortion Detection or DDT gain reduction mode, the spea er load remains connected, but clipping
percentage or output power are instantly reduced. When a problem occurs that causes a channel to go
into a protection mode, the TEMP LED or DC LED for that channel will glow. DC voltage on the output,
excessive subsonic frequencies, or thermal overload will cause the channel’s output relay to disconnect
the spea er load until the problem is corrected or the amplifier cools down.
DDiissttoorrttiioonn DDeetteeccttiioonn LLiimmiittiinngg
Any time a channel is driven into hard, continuous clipping, the DDT circuit will automatically reduce
the channel gain to a level just slightly into clipping, guarding the spea ers against the damaging high
power continuous square waves that may be produced. Situations that may activate the DDT circuit
include uncontrolled feedbac , oscillations, or an improper equipment setting or malfunction upstream
from the amplifier. On the CS3000H, normal program transients will not trigger DDT; only steady,
excessive clipping will. The DDT LED will glow brightly and continuously when limiting occurs.
LLFFCC IImmppeeddaannccee SSeennssiinngg
The CS3000H features innovative circuitry that allows safe operation into any load. When an amplifier
sees a load that overstresses the output stage, the Load Fault Correction circuit adjusts the channel
gain to a safe level. This method of output stage protection is far superior to conventional, brute force
type limiting found on other amplifiers. The LFC circuit is sonically transparent in normal use and
unobtrusive when activated.
TThheerrmmaall PPrrootteeccttiioonn
The internal fans will eep the amplifier operating well within its intended temperature range under all
normal conditions. If a channel’s heat sin temperature reaches 85°C which may indicate an obstructed
air supply, that channel will independently protect itself by disconnecting its load and shutting down
until it has cooled. During this time, the channel’s TEMP LED will light. During this time, the ACTIVE LED
will go out, the Temp and DDT LEDs will stay lit and the cooling fans will stay running at high speed.

10
SShhoorrtt CCiirrccuuiitt
If an output is shorted, the LFC and thermal circuits will automatically protect the amplifier. The LFC
circuit senses the short circuit as an extremely stressful load condition and attenuates the signal,
protecting the channel’s output transistors from over current stress. If the short circuit remains, the
channel will eventually thermally protect itself by disconnecting the load.
DDCC VVoollttaaggee PPrrootteeccttiioonn
If an amplifier channel detects DC voltage or subsonic frequencies at its output terminals, its output
relay will immediately open to prevent loudspea er damage. The channel’s DC LED will light.
TTuurrnn--OOnn//TTuurrnn--OOffff PPrrootteeccttiioonn
At power-up, the amplifier stays in the protect mode, with outputs disconnected, for approximately
four seconds while the power supplies charge and stabilize. While the output relays are open, the DDT
LEDs light. When power is removed, the spea er loads immediately disconnect so that no thumps or
pops are heard.
RRaammppUUpp™™SSiiggnnaall CCoonnttrrooll
Whenever amplifier powers up or comes out of a protect mode, the RampUp™ circuit activates. While
the spea ers are disconnected, the RampUp™ circuit fully attenuates the signal. After the output
relay closes, the signal slowly and gradually raises up to its set level. The RampUp™ Signal Control
circuit has some important advantages over the conventional instant-on circuits:
If a signal is present during power-up (or when coming out of protect), the spea ers are
spared a sudden, potentially damaging burst of audio power.
Because the gain is reduced until after the output relay closes, no arcing occurs at the
contacts, thereby extending their useful life.
SSppeeaakkeerr PPrrootteeccttiioonn
All loudspea ers have electrical, thermal and physical limits that must be observed to prevent
damage or failure. Too much power, low frequencies applied to high frequency drivers, severely
clipped waveforms, and DC voltage can all be fatal to cone and compression drivers. The Peavey
CS3000H amplifier automatically protects spea ers from DC voltages and subsonic signals. For more
information, see the section on Protection Features. Mid- and high-frequency spea ers, especially
compression drivers, are highly susceptible to damage from overpowering, clipped waveforms, or
frequencies below their rated pass band. Be extremely careful that the low and mid bands of an
electronic crossover are connected to the correct amplifiers and drivers and not accidentally
connected to those for a lower frequency band. The amplifier’s clipping point is its maximum pea
output power, and the high power Peavey CS3000H amplifier can deliver more power than many
spea ers can safely handle. Be sure the pea power capability of the amplifier is not excessive for
your spea er system.
Fuses may also be used to limit power to spea er drivers, although as current-limiting rather than
voltage-limiting devices, they are an imperfect solution, and as the wea est lin s, they only limit once
before needing replacement. Some poor quality fuses have a significant series resistance that could
degrade the amplifier’s damping of the spea er’s motion and may even deteriorate the system’s
sound quality. If you elect to use fuses, chec with the spea er manufacturer to determine the proper
current rating and time lag required.
Do not drive any low-frequency spea er enclosure with frequencies lower than its own tuned
frequency; the reduced acoustical damping could cause a ported spea er to bottom out even at
moderate power. Consult the spea er system specifications to determine its frequency limits.

11
SSppeeaaeerr OOuuttppuutt SShhoocc HHaazzaarrdd WWaarrnniinngg::
Warning, the spea er output connections of this amplifier are hazardous live and presents a shoc
hazard when they are energized. Ta e the following precautions;
1. Do not touch any bare wires that are connected to the spea er output connectors.
2. Use insulated spea er cables and touch proof connectors on the spea ers.
3. Do not attempt to ma e connections to the output connectors or to spea er connectors when the
amplifier is turned on.
4. Double chec all connections and ma e sure there are no exposed wires or connectors before
turning the amplifier on.
5. Ma e sure there are no frayed cables or wires and that all connections are tight and secure every
time before turning the amplifier on.
6. External wiring connected to these terminals requires instructions by an instructed
person or the use of ready-made leads or cords.
AAmmpplliiffiieerr MMaaiinntteennaannccee aanndd UUsseerr RReessppoonnssiibbiilliittyy
A CS3000H amplifier requires no other routine maintenance and should never need any internal
adjustment during its lifetime. Your CS3000H amplifier is very powerful and can be potentially
dangerous to loudspea ers and humans ali e. It is your responsibility to read the Important
Precautions section and to ma e sure that the amplifier is installed, wired and operated properly as
instructed in this manual. Many loudspea ers can be easily damaged or destroyed by overpowering,
especially with the high power available from a bridged amplifier. Read the Spea er Protection section
and always be aware of the spea er’s continuous and pea power capabilities.

12
+
-
+
-
Output Relay
Stereo
Bridge
Parallel
/Full Range Thru
CCSS33000000HH BBlloocc DDiiaaggrraamm

13
GGlloossssaarryy ooff TTeerrmmss
( sed in Setup Instructions)
SStteerreeoo:: Music with two separate channels‚ usually a left and right channel.
MMoonnoo:: Music with only one channel.
CCrroossssoovveerr:: An electronic device that separates high and low frequencies and sends them to different outputs. The separate
signals are usually sent to a high out and a low out.
BBii--aammpp:: The separation of high and low frequencies with a crossover‚ using separate spea ers and power amps for each.
FFuullll RRaannggee:: Both high and low frequencies together in a single channel.
PPrrooggrraamm:: The signal that is plugged into the amplifier.
HHii--ppaassss:: Allows only the high frequencies to pass‚ effectively bloc ing the low frequencies.
LLooww--ppaassss:: Allows only the low frequencies to pass, bloc ing the high frequencies.
MMiidd//HHiigghh:: The spea er designed to play everything but the low frequencies.
SSuubb:: The spea er designed for low frequencies only.
PPaarraalllleell:: Both spea ers or inputs having the same signal. When referring to spea ers‚ this means plugging the second
spea er into the first spea er and so on…

14
2 1 3
86 74 5
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
SStteerreeoo OOppeerraattiioonn
1. Set AAMMPP MMOODDEE switch to SSTTEERREEOO.
2. Set the A and B channel AAMMPP FFUUNNCCTTIIOONN switches and to FFUULLLL RRAANNGGEE.
3. Connect the Left and Right program signal to the A and B channel inputs: and .
4. Connect the A and B channel spea er outputs and to the loudspea er full range inputs.
1
2 3
4 5
6 7
MMoonnoo BBrriiddggee MMooddee OOppeerraattiioonn
1. Set AAMMPP MMOODDEE switch to BBRRIIDDGGEE.
2. Connect the Mono program signal to the A channel input .
3. Connect the loudspea er across the two RED banana posts on the amplifier outputs . The A channel is positive
and the B channel is negative.
Caution: The input level controls for both the A and B channels need to be set identically for
the amplifier to operate properly.
1
4
5
TTwwoo CChhaannnneell MMoonnoo——PPaarraalllleell MMooddee (with single channel input)
1. Set AAMMPP MMOODDEE switch to PPAARRAALLLLEELL.
2. Connect the Mono program signal to the A channel input .
3. Connect the loudspea ers to both the A and B channel outputs: and .
1
4
6 7

15
MMoonnoo BBii--AAmmpp OOppeerraattiioonn (sub woofer & mid/high enclosure)
1. Set AAMMPP MMOODDEE switch to SSTTEERREEOO.
2. Set the channel A AMP FUNCTION switch to HHIIGGHHPPAASSSS.
3. Turn on the channel A LLOOWWCCUUTT .
4. Set channel A LLOOWWCCUUTT frequency adjustment nob to match the low frequency cut-off or the -3 dB down point
of the sub woofer. (If you don’t know this specification‚ set it for 40 Hz.)
5. Set the channel A CCRROOSSSSOOVVEERR frequency adjustment nob to the desired crossover frequency (usually
100–150 Hz).
6. Set the channel B AAMMPPFFUUNNCCTTIIOONN switch to FULL RANGE.
7. Plug a short shielded cable into the high pass/full range output of channel A .
8. Connect the other end of the same cable to the channel B input .
9. Connect the Mono program signal to the channel A input .
10. Connect the sub woofer(s) (in parallel) to the channel A output .
11. Connect the mid/high enclosure(s) (in parallel) to the channel B output .
1
2
4
5
6
7
8
9
10
11
3
1 69 2 3
5 4 7 8 10 11

16
INSERT
MIC
(TRS)
(BAL)
RIGHT
OUT
LINE
(BAL)
LEFT
OUT
(BAL)(BAL)(BAL)
(UNBAL)
MONO
OUT
(UNBAL) (UNBAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
INSERT
MIC
(TRS)
(BAL)
LINE
(BAL)
LEFT
RIGHT POLARITY
MIC(BAL)
LINE
(BAL)
MIC
LINE
(BAL)
LEFT
RIGHT
MIC(BAL)
MIC(BAL) MIC(BAL)
REVERSED
NORMAL
0 dB
-20 dB
PAD
POLARITY
REVERSED
NORMAL
0 dB
-20 dB
PAD
MONO/
LEFT
T=IN
R=OUT
SUB 1
OUT
COMP 1
I/O
RETURN 1
RIGHT
INSERT
(TRS)
INSERT
(TRS)
INSERT
(TRS)
70 WATTS
00VAC -240VAC
A PRODUCT OF PEAVEY ELECTRONICS CORP.
MERIDIAN MS. MADE IN U.S.A.
171819
20
21 22 23s
24s 910111213141516 1234
5
678
LEFT
INPUT
RIGHT
INPUT
LEFT
INPUT
RIGHT
INPUT
RIGHT LEFT
MONO
AUX 2
OUT
(BAL)
(UNBAL)
AUX 1
OUT
(BAL)
(UNBAL)
AUX 3
OUT
(BAL)
(UNBAL)
AUX 4
OUT
(BAL)
AUX 5
OUT
(UNBAL)
AUX 6
OUT
(UNBAL)
T=IN
R=OUT
SUB 2
OUT
COMP 2
I/O
T=IN
R=OUT
SUB 3
OUT
COMP 3
I/O
T=IN
R=OUT
SUB 4
OUT
COMP 4
I/O
RETURN 2
MONO/
LEFT
RIGHT
(UNBAL)
POWER
WARNING:
CAUTION
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
AVIS:
TO RAIN OR MOISTURE.
ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT
TO REDUCE THE RISK OF FIRE OR
50/60 Hz
24 CHANNEL LI E SOUND CONSOLE
TM
QUAD SUB-MASTER COMPRESSION
WITH
PIN = GND
PIN 2 = POS
PIN 3 = NEG
RQ 4324 C
(UNBAL)
(UNBAL)(UNBAL)(UNBAL)(UNBAL)
RQ 4324
Q 215F
CEL 2a
Feedback Ferret II
SP2X SP2X SP218 SP218
CS 800S
Kosmos
CS3000H
BBii--aammpp HHoooouupp DDiiaaggrraamm

17
RRaatteedd ppoowweerr::
BBrriiddggeedd 44 OOhhmmss::
3000 Watts @ 1 Hz @ <0.1% THD
22 xx 22 OOhhmmss::
1500 Watts per channel @ 1 Hz @
<0.1% THD both channels driven
22 xx 44 OOhhmmss::
1100 Watts per channel @ 1 Hz @
<0.05% THD both channels driven
22 xx 88 OOhhmmss::
700 Watts per channel @ 1 Hz @
<0.05% THD both channels driven
11 xx 22 OOhhmmss::
2150 Watts per channel @ 1 Hz @
<0.1% THD
11 xx 44 OOhhmmss::
1400 Watts per channel @ 1 Hz @
<0.05% THD
11 xx 88 OOhhmmss::
825 Watts per channel @ 1 Hz @
<0.05% THD
MMiinniimmuumm llooaadd iimmppeeddaannccee::
2 Ohms
MMaaxxiimmuumm RRMMSS vvoollttaaggee sswwiinngg::
87 Volts
FFrreeqquueennccyy rreessppoonnssee::
10 Hz–100 Hz; +0‚ -0.5 dB @ 1 Watts
PPoowweerr bbaannddwwiiddtthh::
10 Hz–35 Hz; +0‚ -3 dB @ rated 4 Ohm
power
TTHHDD ((22 xx 22 OOhhmmss))::
<0.2% @ 1100 Watts per channel from
20 Hz–20 Hz
TTHHDD ((22 xx 44 OOhhmmss))::
<0.1% @ 950 Watts per channel from
20 Hz–20 Hz
TTHHDD ((22 xx 88 OOhhmmss))::
<0.1% @ 650 Watts per channel from
20 Hz–20 Hz
IInnppuutt CCMMRRRR::
-85 dB @ 1 Hz
VVoollttaaggee ggaaiinn::
x40 (32 dB)
CCrroossssttaall::
>-70 dB @ 1 Hz @ rated power @
8Ohms
CCrroossssoovveerr::
Third Order State Variable Filters:
18 dB/octave
Frequency Range: 40 Hz–300 Hz
HHuumm aanndd nnooiissee::
>-108 dB; “A” weighted reference to
rated power @ 8 Ohms
SSlleeww rraattee::
>15V/us
DDaammppiinngg ffaaccttoorr ((88 OOhhmmss))::
>500:1 @ 20 Hz–1 Hz
PPhhaassee rreessppoonnssee::
+5 to -12˚ from 20 Hz–20 Hz
IInnppuutt sseennssiittiivviittyy::
1.66 Volts +/- 3% for 1 Hz @ 4 Ohm
rated power;
1.37 Volts +/- 3% for 1 Hz @
2 Ohm rated power
IInnppuutt iimmppeeddaannccee::
15 Ohms‚ balanced
MMaaxx IInnppuutt PPoowweerr ww//ttyyppiiccaall mmuussiicc
pprrooggrraamm::
1400 Watts @ 2 Ohms
935 Watts @ 4 Ohms
MMaaxx IInnppuutt PPoowweerr ww//sseevveerree mmuussiicc
pprrooggrraamm::
3372 Watts @ 2 Ohms
2425 Watts @ 4 Ohms
CCoooolliinngg::
Two front panel temperature-dependent
variable speed 80 mm high-output DC
fans
CCoonnttrroollss::
Two front panel attenuators‚ rear panel
Mode switch‚ Function switch per
channel‚ High Pass adjustable filter per
channel. High Pass filter bypass switch
per channel‚ adjustable subwoofer
crossover per channel.
IInnddiiccaattoorr LLEEDDss::
Two ACL (clip limiting)‚ two signal
presence‚ two active status‚ two DC
protect‚ two temperature limit
PPrrootteeccttiioonn::
Thermal‚ DC‚ turn-on bursts‚ subsonic‚
incorrect loads
CCoonnnneeccttoorrss::
Combi XLR and 6.3 mm phone input;
Spea on and binding post spea er
output; 6.3 mm high pass or full range
patch connector per channel; 6.3 mm
low pass patch connector per channel;
15 amp IEC mains connector
CCoonnssttrruuccttiioonn::
16 ga. steel with cast aluminum front
panel and handles
DDiimmeennssiioonnss::
3.5" x 19" x17.375" overall 16"
88.9 mm x 483 mm x 441 mm 406 mm
inside rac depth
NNeett WWeeiigghhtt::
43 lbs. (19.5 g)
GGrroossss WWeeiigghhtt::
45.5 lbs. (20.6 g)
All power measurements made at 120 VAC‚
power transformer cold. 2 Ohm power is
time limited by magnetic circuit brea er.
CCSS®®33000000HH
SSPPEECCIIFFIICCAATTIIOONNSS

18
EESSPPAAÑÑOOLL
FFeeaattuurreess
DDeessccrriippttiioonnSSeerriiee CCSS ddee AAmmpplliiffiiccaaddoorreess ddee PPooddeerr
Felicidades en tu compra de un amplificador de la Serie CS de Peavey, diseñado para brindarte años
de operación confiable bajo el uso más exigente. Estos amplificadores ofrecen superioridad sonora y
la confiabilidad inmejorable que por tanto años ha sido relacionada con Peavey, manteniendo un
tamaño compacto. Tecnología avanzada y extensos circuitos de protección permiten la operación a
gran eficiencia en condiciones no siempre perfectas, y con cargas pesadas. El circuito DDT™
(identificador de distorsión) permite la operación sin problemas en cargas tan bajas como 2 Ohmios.
El circuito Identificador de Distorsión protege a los drivers y asegura que se mantiene integridad en
el sonido, aun en condiciones de saturación extrema. El diseño altamente eficiente de Peavey usa
parrillas de calor enfriadas por túneles y ventiladores DC de velocidad variable. Esta topología de
enfriamiento mantiene un promedio de temperatura de operación más bajo, resultando en vida
prolongada de los transistores de salida.
A pesar que la serie de amplificadores CS de Peavey es muy simple de operar y reside dentro de un
chasis ultra-fuerte de acero, el uso indebido puede ser peligroso. Algunos de estos modelos son
amplificadores de poder muy alto que pueden producir voltajes altos y corrientes considerables de
hasta 30 Hz. Siempre hay que ejercer técnicas de operación seguras con estos amplificadores.
PPAARRAA TTUU SSEEGGUURRIIDDAADD,, LLEEEE LLAA SSEECCCCIIÓÓNN DDEE PPRREECCAAUUCCIIOONNEESS,, AASSII CCOOMMOO LLAASS DDEE SSAALLIIDDAA,, EENNTTRRAADDAA YY
CCOONNEEXXIIOONNEESS DDEE CCOORRRRIIEENNTTEE..
··DDiisseeññoo ddee rraacc ddee ddooss eessppaacciiooss yy 1199""..
··PPaarrrriillllaass ddee ccaalloorr eennffrriiaaddaass ppoorr vveennttiillaaddoorreess DDCC ddee vveelloocciiddaadd vvaarriiaabbllee..
··CChhaassiiss ddee aacceerroo ddee ccoonnssttrruucccciióónn ffuueerrttee..
··CCoonnttrrooll ddee sseeññaall RRaammppUUpp™™..
··33 mmooddooss ddee ooppeerraacciióónn:: eessttéérreeoo,, ppaarraalleelloo yy mmoonnoo--ppuueennttee..
··IInntteerrrruuppttoorr ddee ccoorrrriieennttee yy ffuussiibbllee eenn eell ppaanneell ffrroonnttaall..
··IInntteerrrruuppttoorr ddee ffuunncciioonneess ddeell aammpplliiffiiccaaddoorr ccoonn rraannggoo ccoommpplleettoo ddee ooppeerraacciióónn oo ssaalliiddaass
ggrraavveess//aagguuddaass ddeell ccrroossssoovveerr..
··DDooss ccrroossssoovveerrss iinnddeeppeennddiieenntteess aajjuussttaabblleess..
··DDooss ffiillttrrooss iinnddeeppeennddiieenntteess ddee ggrraavveess..
··CCiinnccoo iinnddiiccaaddoorreess ddee LLEEDD eenn eell ppaanneell ffrroonnttaall ppoorr ccaannaall:: AACCTTIIVVOO,, DDDDTT™™,, SSEEÑÑAALL,, TTEEMMPP yy DDCC..
DDeesseemmppaaqquuee
Al desempacar inspecciona el amplificador. Si encuentras algún problema, notifica al proveedor
inmediatamente. Sólo el consignatario puede llevar a cabo una queja por daños durante el envío.
Asegúrate de guardar la caja y todos los materiales de empaque. Si alguna vez fuera necesario enviar
la unidad a Peavey Electronics, una de sus oficinas, centros de servicio, etc., usa solamente los
empaques originales de fábrica. Si la caja no está disponible, contacta a Peavey para obtener una
nueva.
IInnssttaallaacciióónn
Los amplificadores de la Serie CS se montan en un rac estándar de 19". También se incluyen orejas
de instalación traseras para soporte adicional, que es recomendable en instalaciones no
permanentes y de giras. Dado que las conexiones y cables se encuentran en el panel trasero, un
desarmador en ángulo o llave hex puede facilitar la montura de las orejas traseras a los rieles.
RReeqquuiissiittooss ddee eennffrriiaammiieennttoo..
La serie de amplificadores CS usa un sistema de enfriamiento de aire forzado que mantiene una
temperatura de operación baja y uniforme. El aire se mete al amplificador por medio de ventiladores
en el panel frontal, viaja por las aletas de enfriamiento de las parrillas de enfriamiento, y luego sale

19
por las aperturas en la parte trasera y laterales. Si se llegara a calentar la parrilla de enfriamiento su
circuito de seguridad desconectará la carga del canal específico. Es importante tener una salida para el
aire en la parte trasera de la unidad y suficiente espacio alrededor de los lados del amplificador para
permitir que el aire de enfriamiento pueda salir libremente. Si el amplificador es instalado en un rac , no
se usen puertas o cubiertas en la parte delantera del rac ; la entrada del aire debe fluir sin resistencia. Si
se usan rac s con la parte trasera cerrada, hay que asegurarse que hay una apertura de un (1) espacio de
rac estándar por cada tres amplificadores montados.
PPrreeccaauucciioonneess ddee OOppeerraacciióónn
Hay que asegurarse que el voltaje utilizado es el mismo impreso en la parte trasera del amplificador. Los
daños que resulten del uso del voltaje equivocado no están cubiertos por ninguna garantía. Ver la sección
de Conexión de Corriente para más información en los requisitos de corriente.
NNoottaa::SSiieemmpprree aappaaggaa yy ddeessccoonneeccttaa eell aammpplliiffiiccaaddoorr ddee llaa ffuueennttee ddee ccoorrrriieennttee aanntteess ddee lllleevvaarr aa ccaabboo
ccuuaallqquuiieerr ccoonneexxiióónn ddee aauuddiioo.. TTaammbbiiéénn,, ccoommoo pprreeccaauucciióónn aaddiicciioonnaall,, ssee rreeccoommiieennddaa tteenneerr llooss aatteennuuaaddoorreess
hhaassttaa aabbaajjoo dduurraannttee eell eenncceennddiiddoo..
A pesar que los amplificadores de la serie CS cuentan con circuitos RRaammUUpp™™, que suben el nivel de la
señal de forma gradual cuando la salida se cierra, siempre es una buena idea tener los controles de
ganancia abajo durante el encendido para prevenir daños a los parlantes si hubiera una señal muy alta en
la entrada. Ya sea que los compres, o que los hagas, siempre hay que usar conectadores de la mejor
calidad, así como cables de entrada y para los parlantes, así como buena técnica para soldar, para
asegurar una operación sin problemas. La mayoría de los problemas intermitentes tiene que ver con
cables de baja calidad.
Consulta la Tabla de Tamaños de Cables (abajo) para determinar los tamaños adecuados de diferentes
impedancias y longitudes de cable. Recuerda que la resistencia de los cables le roba poder al
amplificador de dos maneras: poder perdido directamente a la resistencia (pérdida I2R), y por la
atenuación de la impedancia de la carga total. También, hay que asegurarse que el interruptor de modo
esté correctamente ajustado para la aplicación deseada. Ver las SSeecccciioonneess ddee OOppeerraacciióónn EEssttéérreeoo,, PPaarraalleelloo
yy MMoonnoo//PPuueenntteepara más información.

20
WIRE GAUGE CHART
Cable Length
(In Feet)
Stranded Wire auge
(AW )
Power Loss into
8 ohms (%)
Power Loss into
4 ohms (%)
Power Loss into
2 ohms (%)
5 18 .79 1.58 3.16
16 .50 1.00 2.00
14 .31 .62 1.24
12 .20 .40 .80
10 .125 .25 .50
10 18 1.58 3.16 6.32
16 1.00 2.00 4.00
14 .62 1.25 2.50
12 .40 .80 1.60
10 .25 .50 1.00
40 18 8.00 12.60 25.20
. 16 4.00 8.00 1.60
14 2.50 5.00 10.00
12 1.60 3.20 6.40
10 1.00 2.00 4.00
8 .625 1.25 2.50
80 16 8.00 16.00 32.00
14 5.00 10.00 20.00
12 3.20 6.40 12.80
10 2.00 4.00 8.00