peerless-AV DS-LEDA27-4x4 User manual

12018-05-15 #:146-9026-9 (2020-08-20)
DS-LEDA27 Series
For Absen Acclaim
*Actual conguration may vary
ENG Installation video for reference only.
Read and follow instruction manual for full installation.

22018-05-15 #:146-9026-9 (2020-08-20)
Symbols
ENG
WARNING
ENG
Do not overtighten screws.
ENG
Tools Needed for Assembly.
ENG
5/32"
(4mm)
3/8"
(10mm)
2.5mm
Wear anti-static gloves.
ENG
1
2
ENG To properly tighten screws: Tighten until screw
head makes contact, then tighten another 1/2
turn. Do not overtighten screws.
4
+1/2
3
ENG - This product is designed to be installed on plywood walls. Hardware is included for plywood installation.

walls. Before installing make sure the supporting surface will support the combined load of the equipment and
hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and product may fail.
Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift
and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to

call customer care at 1-800-865-2112.
WARNING

32018-05-15 #:146-9026-9 (2020-08-20)
H
I
JM5 x 5mm
set screw
#14 x 1.75"
wood screw
M5 x 8mm
A1 A2 C
left column right column inside vertical
column kit
Parts List
Description
outside vertical column kit
A1 left column
A2 right column
spacer kit
B1 top vertical spacer
B2 bottom vertical spacer (not used)
B3 horizontal spacer
Cinside vertical column kit
Dtop horizontal extrusion asy
Ebottom horizontal extrusion asy
F extrusion connector
G 3mm allen wrench 2-tip t-handle
H M5 x 5mm set screw
I #14 x 1.75" wood screw
JM5 x 8mm socket button screw
K wall plate shim
Parts (Before beginning, make sure you have all parts shown below).
ENG
D
E
top horizontal
extrusion asy
bottom horizontal
extrusion asy
K
wall plate
shim
B3
horizontal
spacer
F
extrusion
connector
B2B1 bottom vertical
spacer
top vertical
spacer
G
3mm allen wrench
two-tip T-handle

42018-05-15 #:146-9026-9 (2020-08-20)
1-1
Optional: If connecting two top horizontal extrusions,

ENG
Remove and save hardware.
ENG
D
D
1-2
Use extrusion connectors to connect top horizontal
extrusions.
ENG
F (4) H (8)
D
D
G
2.5mm

52018-05-15 #:146-9026-9 (2020-08-20)
2-1
Optional: If connecting two bottom horizontal

ENG
Remove and save hardware.
ENG
E
E
1-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
D
D
G
G

62018-05-15 #:146-9026-9 (2020-08-20)
2-2
Use extrusion connectors to connect bottom
horizontal extrusions.
ENG
H (6)
F (3)
E
E
E
E
2-3
Replace one hook-on bracket in between connected
extrusions.
ENG
Use saved hardware.
ENG
G
2.5mm

72018-05-15 #:146-9026-9 (2020-08-20)
3-1
Use a laser level to keep mounting holes
level.
ENG
3
ENG - When installing Peerless wall mounts on a wood stud wall covered with plywood, verify that the wood
studs are a minimum of 2" x 4" nominal size and plywood is a minimum Grade BC, 1/2" (13 mm) thick. Plywood
may be covered by gypsum board (drywall) up to 5/8" thick.
WARNING

82018-05-15 #:146-9026-9 (2020-08-20)
3-2
Level top horizontal extrusion and mark
mounting holes on plywood (must be
minimum Grade BC, 1/2" (13mm) thick.)
ENG
D
3.94"
(100mm)
display tile
7/8"(22mm) minimum
for mounting clearance

92018-05-15 #:146-9026-9 (2020-08-20)
3-3
Drill mounting holes into supporting surface
(1.75" (44mm) minimum depth required).
ENG
5/32"
(4mm)
1.75"
(44mm)
5/32"
(4mm)
3-4
Level extrusion. Install using wood screws
provided.
ENG
3/8"
(10mm)
Maximum 80 in. • lb (9 N.M.).
ENG
D
I (7)

10 2018-05-15 #:146-9026-9 (2020-08-20)
3-5

horizontal extrusion.
ENG
3/8"
(10mm)

ENG
B1
I
D
B1 (2)