PEERLESS A100IWBMOUNT Guide

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
1 of 16
Installation and Assembly: Wallmount for CPA100 and
Whiteboard
Model: A100IWBMOUNT
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
Maximum Load Capacity for Screen: 53 lb (24 kg)
Maximum Load Capacity for Projector : 13.5 lb (6 kg)

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
2 of 16
NOTE: Read entire instruction sheet before you start installation and assembly.
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please
callPeerlesscustomercareat1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-
wareand components.
• Neverexceed the Maximum Load Capacity. See pageone.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly,but do not overtighten. Overtightening candamagethe items, greatly reducing their holding
power.
• Carriagebox has over 100 lbs (43 kg) of pressure. Be careful not to pinch fingers.
• Thisproductis intended for indoor use only. Use of this product outdoorscould leadtoproduct failure and personal
injury.
• Thisproduct was designed and intended to be mounted tothefollowing supporting surfaces checked below with the
hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-
ing surface, contact Peerless customer care at 1 800 865-2112.
• This product was designed to be installed on the following wall construction only;
WALLCONSTRUCTION ADDITIONALHARDWAREREQUIRED
xWoodStud None
WoodBeam None
xSolidConcrete None
xCinderBlock None
xMetalStud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
Brick ContactCustomer Service
Otheror unsure? ContactCustomer Service
WARNING
Tools Needed for Assembly
•studfinder ("edge to edge" stud finder is recommended)
•phillipsscrewdriver
•drill
•1/4" bit for concrete and cinder block wall
•1/2" bit for metal stud wall
•5/32" bit for metal or wood stud wall
•level

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
3 of 16
G
Beforeyou begin, make sure all parts shown are included with your product. B
C
A
D
H J
LK
MNOPQ
EF I
CARRIAGE
RST
Partsmay appear slightly different than illustrated.
Description Qt
y
. Part #
A
wall mount assembly 1 055-1841
Bprojector tube 1 055-1839
Cprojector arm 1 055-1830
Dadapter plate 1 055-1828
Ehook bracket 2 055-1840
Fvertical handle 2 055-1834
Ghorizontal handle 1 055-1858
Hprojector adapter plate 1 055-1822
Islide plate 1 055-1821
Jprojector mount 1 PRG-1
K#10-32 x 0.375" phillips screw 18 520-1130
LM6 x 12 mm serrated washer head socket pin screw 8 510-1050
M0.25"ID spacer 4 590-1050
N1/4-20 x 1.0" hex head screw 2 520-1606
O#10-32 x 3/8" serrated washer head socket pin screw 2 520-1151
P0.25" ID nylon washer 4 540-9460
Q#14 x 2.5" wood screw 6 5S1-015-C03
Racorn nut 2 530-1049
Splug 1 590-1303
T#10-32 x 1-3/8" socket pin screw 2 510-1098
Ualligator anchor 6 590-0097
V
5/32" (4 mm) security allen wrench 1 560-9646
W#10-32 x 1/4" socket pin screw 2 520-1196
X
flanged bushing 1 590-1271
Y
retainer bushing 1 055-1836
Zcable tie 6 560-9711
toggler pack 1
A
CC615
Parts List

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
4 of 16
1Make sure that wall mount assembly (A) is level, use it as a template to mark the top two mouting holes.
Alternatively, the top two screws can be fastened 16" apart as detailed in step 2 while making sure that they are
level. In order to set the desired height of bottom of screen in the lowest position, refer to dimension X from the chart
below.
FLOOR
PROJECTOR
SCREEN
A
Parts List Continued
UV
X
BOTTOMOF
SCREEN
WX Y
TOP
MOUNTING
HOLES
Screen Size Dimension X
63" 36"
77'' 42"
CHART
Z

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
5 of 16
Make sure that the mounting holes are on the stud centerline. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep.
Fasten two #14 x 2.5" wood screws (Q) into top mounting holes leaving a .25" of exposed thread as shown. Hook
wall mount assembly (A) onto #14 x 2.5" wood screws (Q) as shown in fig. 2.1.
Fasten four #14 x 2.5" wood screws (Q) into wall mount assembly (A) as shown in fig. 2.2. Make sure that the wall
mount assembly (A) is level, tighten all six #14 x 2.5" wood screws (Q).
Skip to step 3.
Installation to Wood Stud Wall
• Installermust verify that the supporting surface will safely support the combined load of the equipment andallattached
hardwareandcomponents.
• Tightenwood screws so that wall plate is firmly attached, but donotovertighten.Overtightening can damage the
screws,greatly reducing their holdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovided is for attachment of mount throughstandardthickness drywall or plaster into wood studs.Installers
areresponsible to provide hardwarefor other types ofmountingsituations.
WARNING
2
fig. 2.1
fig. 2.2
CARRIAGE
CARRIAGE
.25"
A
Q
Q
A

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
6 of 16
CORRECT
wallplate concrete
plaster/
drywall
Installation to Solid Concrete or Cinder Block
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breakingout the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-
wareand components.
WARNING
CUTAWAYVIEW
• Tighten screws so that wall mount is firmly attached,
butdo not overtighten.Overtightening candamage
screws,greatly reducing their holdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
SOLID
CONCRETE
CINDERBLOCK
• Always attach concrete anchors directly to load-
bearingconcrete.
• Neverattach concrete anchorsto concrete covered
withplaster,drywall, or other finishing material. If
mountingto concrete surfaces coveredwitha finishing
surfaceis unavoidable, the finishing surfacemust be
counterboredas shown below.Be sureconcrete
anchorsdo not pull away from concrete when tighten-
ing screws. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
WARNING
2concrete
surface
1
3
2
U
Drill holes and insert anchors (U).
Place wall mount assembly (A)over anchors (U) and
secure with screws (Q).
Tighten all fasteners.
A
U
Q
U
CARRIAGE
AQ
fig. 2.3
Use wall mount assembly (A) as a template to mark
mouting holes. Drill six 5/32" (4 mm) dia. holes to a
minimum depth of 2.5" (65 mm). Insert six anchors (U) in
holes flush with wall as shown (right). Fasten two #14 x
2.5" wood screws (Q) into top anchors (U) leaving a .25" of
exposed thread for each screw (Q) as shown. Hook wall
mount assembly (A) onto #14 x 2.5" wood screws (Q) as
shown in fig. 2.3. Fasten four #14 x 2.5" wood screws (Q)
into wall mount assembly (A) as shown. Make sure that the
wall mount assembly (A) is level, tighten all six #14 x 2.5"
woodscrews (Q).
Skip to step 3.
INCORRECT
wallplate
plaster/
drywall
concrete
.25"
Q

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
7 of 16
Drill six 1/2" holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes prior to
drilling 1/2" holes.
Refer to instruction sheet included with Peerless accessory kit ACC 615 for metal studs to install togglers.
Fasten two 1/4-20 x 2-1/2" screws into top mounting holes leaving a .25" of exposed thread on each as shown in
fig. 2.4. Hook wall mount assembly (A) onto 1/4-20 x 2-1/2" screws.
Fasten four 1/4-20 x 2-1/2" screws into wall mount assembly (A) as shown in fig. 2.5. Make sure that the wall mount
assembly (A) is level, tighten all six 1/4-20 x 2-1/2" screws.
• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.
• Installermust verify that the supporting surface will safely support the combined load of the equipment andallattached
hardwareandcomponents.
WARNING
Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 615 Required)
TOGGLER
Afig. 2.4
1/4-20X 2-1/2" PHILLIPS SCREWS
2
.25"
fig. 2.5
A
CARRIAGE
CARRIAGE
1/4-20X 2-1/2" PHILLIPS SCREWS

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
8 of 16
A
CARRIAGE
K
B
77" SCREEN
CARRIAGE
63" SCREEN
A
K
B
Fasten three #10-32 x 0.375" phillips
screws(K)to carriage leaving three
threadsexposed.Attachretainer
bushing(Y)andflanged bushing (X)to
wall mount assembly (A)using two
#10-32 x 0.375" phillips screws (K).
Slide projector tube (B) into top of wall mount
assembly (A) and secure with two #10-32 x
0.375" phillips screws (K) as shown below.
NOTE: Usecorrectset of mounting holes for
the screen size as shown below.
34
D
K
K
D
THREE
THREADS
EXPOSED
K
Hookadapter plate (D)onto three
#10-32 x 0.375" phillips screws (K).
Fasten three #10-32x 0.375" phillips
screws(K) into adapterplate (D).
Securely tighten all six #10-32 x
0.375"phillips
4-2
4-1
NOTE:Twist tube
into wall mount
assembly (A).
X
Y
K
A
DETAIL 1
K

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
9 of 16
Fasten two #10-32 x 0.375" phillips screws (K) into adapter plate (D)leaving three threads exposed as shown in
detail 1. Hook each vertical handle (F) onto #10-32 x 0.375" phillips screw (K) as shown in fig 5.1. NOTE: Use top
slot for 77" screen or second slot from top for 63" screen. Fasten #10-32 x 0.375" phillips screws (K) through lower
slot of vertical handle (F) that lines up with the lower hole in adapter plate (D). Hole location for 77" screen is shown
in fig. 5.2. Securely tighten all four #10-32 x 0.375" phillips screws (K).
5
F
D
THREETHREADS
EXPOSED
DETAIL 1
K
D
K
F
fig. 5.1 fig. 5.2
6
63"SCREEN
77"SCREEN
Fastenhorizontal handle(G)toverticalhandle(F)using four #10-32x 0.375" phillips
screws (K) and two acorn nuts (R).
RG
F
K
K
NOTE: 77"hole location
shown. 63" will use second
frombottom hole on vertical
handle(F).
CABLESROUTINGTHROUGH THETUBE
CANBE PULLEDTAUGHTANDFIXEDIN
LINETOTHEHORIZONTALHANDLE(G)BY
USINGCABLE TIES (Z). USEOTHERCABLE
TIESASNEEDED.
K

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
10 of 16
Insert hook brackets into screen as shown in detail 2 and fig. 7.1. Secure each hook bracket (E) with M6 x 12 mm
serrated washer head socket pin screw (L) as shown in fig. 7.2 and detail 3.
7
DETAIL 3
fig. 7.2
E
L
SCREEN
SCREEN
E
fig. 7.1
77"SCREEN
63"SCREEN
DETAIL 2
SCREEN
BRACKET

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
11 of 16
Hook brackets (E) into adapter plate (D) as shown in fig. 8.1 and
detail 4. Thehookswill go over the flange on thetopand the bottom of
hook bracket (E) into the slots as shown in detail 4 and detail 6. Fasten
#10-32 x 1-3/8" socket pin screws (T) on each hook bracket (E), using
security allen wrench (V) and tighten to wall plate as shown in
detail5.
Toremovescreenfrommount, loosensafety/security screwsand liftscreen
offofmount.
• Do not tighten screws with excessive force.
Overtighteningcan cause damageto mount. Tighten
screws to 40 in. • lb (4.5 N.M.) maximum torque.
CAUTION
8
SIDE VIEW
fig 8.1
DETAIL 4
DETAIL 5
E
T
D
E
DED
CONNECTION
BLOCK
CAPTIVE
SCREW
Disengageconnection block from projector mount assembly (J)by unscrewing captive screw and slidingout
connection block as shown.
J
9
DETAIL 6
fig 8.2
HOOK FLANGE
BOTTOMOF HOOK
BRACKET(E)
D

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
12 of 16
FRONT VIEW
I
fig. 10.3
C
J
N
P
Arrowon projectormount assembly(J)indicatesfrontofmount. Thearrow ofprojector mountassembly (J)should
facetowardsthe roundtube onprojectorarm(C).
Fasten projector mount assembly (J) to projector arm (C) using two 1/4-20 x 1.0" hex head screws (N), four 0.25" ID
nylon washers (P) and slide plate (I) as shown in fig. 10.2 and 10.3. Do not tighten 1/4-20 x 1.0" hex head
screws (N) fully to allow for adjustment. Insert rectangle plug (S) into projector arm (C) as shown in fig. 10.2.
Position projector mount assembly (J) so that hole corresponding to your size screen in projector arm (C) is in the
center of projector mount assembly (J) as shown in fig. 10.1. Securely tighten both 1/4-20 x 1.0" hex head screws
(N).NOTE:Thiscanbeadjustedduringfinalprojectoralignmentifneeded.
10
fig. 10.2
P
J
N
I
C
S
Bottom View
fig. 10.1
C
77"SCREEN
63"SCREEN
ARROWINDICATES
FRONTOFMOUNT
ROUNDTUBE

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
13 of 16
Place projector arm (C) onto projector tube (B) as shown in fig. 11.1. Align projector arm (C) so that the holes in
projectortube (B) are in themiddleof projector arm (C) slot. NOTE: Thiscan be adjustedduringfinal projector
alignmentif needed. Fastenprojectorarm (C) toprojectortube (B) usingtwo #10-32 x 3/8"serrated washer head
socket pin screws (O) as shown in fig. 11.2 and detail 6.
O
11
B
C
C
B
fig. 11.1
fig. 11.2
DETAIL 6

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
14 of 16
PROJECTOR
Attachadapter plate (H) to projector using
fourM6 x 12 mm serrated washer head
socket pin screws (L) and 0.25" spacers (M).
NOTE: Shoulderof connection block indi-
cates the back of projector. The screws (L)
should be placed in the center of slots. This
canbe adjusted during final projector
alignmentif needed.
SHOULDER
CONNECTION
BLOCK
CONNECTION
BLOCK
NOTCHINDICATES
FRONTOF
PROJECTOR
SHOULDER
Attaching Adapter Plate to Projector
Align shoulder on connection block opposite notch in
adapter plate (H). Attach adapter plate (H) to
connectionblock from projector mount assembly (J)
using two #10-32 x 3/8" serrated washer head socket
pin screws (O).
H
L
M
H
O
12
13

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
15 of 16
Slide connection block with projector into projector mount assembly (J) as shown. Tighten captive screw to secure
projectorto projector mount assembly (J).
IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (W) through projector mount
assembly (J) and into connection block as shown. Tighten screw using 4mm security allen wrench (V).
CONNECTION
BLOCK
• Donotliftmoreweightthanyoucanhandle.Useadditionalmanpowerormechanicalliftingequipmenttosafelyhandle
placementof the projector.
CONNECTION
BLOCK
Attaching Adapter Plate to Projector Mount
FRONTOF
MOUNT
CAPTIVE
SCREW
ARROWINDICATES
FRONTOFMOUNT J
J
W
WARNING
14
15

ISSUED: 04-08-08 SHEET #: 055-9094-2 06-06-08
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.
16 of 16
To adjust yaw (swivel): Loosen screw on projector mount assembly (J) indicated below until projector mount
can be rotated. Rotate mount to desired position and retighten screw.
To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and
turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.
To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand
foreasyadjustmentor insert #2 phillips screwdriver in end of knob and turn.
Projector Alignment
SCREWFORYAW
(SWIVEL)STOP
KNOBFORROLL
ADJUSTMENT
KNOBFORPITCH
ADJUSTMENT
BACKOFMOUNT
To prevent tampering with the pitch and roll adjustments:Tighten the two tamper resistant security screws
on the projector mount assembly (J) using 4 mm security allen wrench (V) to lock the pitch and roll adjustments
asshown below.
NOTE:Tightenscrews firmly, but donotovertighten.Overtighteningcan damage the mount.
• Do not adjust pitch or roll while tamper resistant security screws are fully engaged.
• Loosen the two tamper resistant security screws one complete turn before adjusting the projector mount assembly or
damagemay occur.
CAUTION
ARROWINDICATES
FRONTOFMOUNT
TOLOCKROLLTIGHTEN
TAMPER RESISTANT
SECURITY SCREW TOLOCKPITCHTIGHTEN
TAMPER RESISTANT
SECURITY SCREW
FRONT VIEW SIDE VIEW
©2008,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
J
16-1
fig. 16.1
16