PEERLESS HT642-002 Guide

Model: HT642-002
Installation and Assembly:
Wall Mount
Max Load Capacity: 75 lb (34 kg)
ISSUED: 03-02-11 SHEET #: 125-9192-1

Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
• studnder("edgetoedge"studnderisrecommended)
• phillips screwdriver
• drillwith1/4"and5/32"drillbits
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................4
Installation to Metal Stud Wall ................................................................................................................................................5
Installation to Solid Concrete and Cinder Block Wall .............................................................................................................6
Attaching Adapter Brackets to Screen....................................................................................................................................7
Attaching Mounting Bracket Using Hook On Option...............................................................................................................8
Attaching Mounting Bracket Using Tilt Option ........................................................................................................................9
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.
• Thisproductshouldonlybeinstalledbyaqualiedprofessional.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-
ware and components.
• NeverexceedtheMaximumLoadCapacityof75lb(34kg).
• Ifmountingtowoodwallstuds,makesurethatmountingscrewsareanchoredintothecenterofthestuds.Useof
an"edgetoedge"studnderishighlyrecommended.
• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• Thisproductwasdesignedandintendedtobemountedtothefollowingsupportingsurfacescheckedbelowwith
thehardwareincludedinthisproductasspeciedintheinstallationsheet.Tomountthisproducttoanalternative
supporting surface, contact Peerless customer care at 1-800-865-2112.
• Thisproductwasdesignedtobeinstalledonthefollowingwallconstructiononly;
WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x WoodStud   None
x WoodBeam   None
x SolidConcrete   None
x CinderBlock   None
x MetalStud   None
Brick Contact Customer Service
Other or unsure? Contact Customer Service
WARNING

3 of 9 ISSUED: 03-02-11 SHEET #: 125-9192-1
A
B
M
Some parts may appear slightly different than illustrated.
Before you start make sure all parts listed are included with your product.
F
C D E
G H I
J
Description Qty. Part #
Across support bracket 1 201-1881
Bwall plate 1 201-1678
C# 8 washer 4 540-1001
DM4 x 12 mm phillips screw 4 504-9013
EM6 x 16 mm phillips screw 4 520-9274
F4 mm allen wrench 1 560-9646
Gtoggler 4 560-9708
H1/4 - 20 phillips screw 4 520-9521
I#14 x 2.5 wood screw 4 5S1-015-C03
JM5 x 12 mm socket pin serrated washer head screw 6 510-1064
KAlligator® concrete anchor 4 590-0097
Ladapter bracket 2 201-1882
M1/4-20 nylock nut 4 530-9413
PARTS LIST
K
L

4 of 9 ISSUED: 03-02-11 SHEET #: 125-9192-1
B
I
Installation to Wood Stud Walls
Useastudndertolocatetheedgesofthestud.Useofanedge-to-edgestudnderishighlyrecommended.
Based on its edges, draw a vertical line down the stud's center. Place wall plate (B) on wall as a template. Mark
thecenterofthefourmountingholes.Drillfour5/32"(4mm)dia.holes2-1/2"(65mm)deep.Securewallplate(B)
towoodstudusingfour#14x2-1/2"woodscrews(I) as shown. Skip to Step 2 page 7
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall
attached hardware and components.
• Tightenwoodscrewssothatwallplateisrmlyattached,butdonotovertighten.Overtighteningcandamagethe
screws, greatly reducing their holding power.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan"edgetoedge"studnder
is highly recommended.
• Hardwareprovidedisforattachmentofmountthroughstandardthicknessdrywallorplasterintowoodstuds.Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
1

5 of 9 ISSUED: 03-02-11 SHEET #: 125-9192-1
Installation to Metal Stud Walls
Rotate toggler (G)
clockwise to wedge it
against inside walls
of metal stud.
Push into hole.
Pivot end of
toggler (G).
Slide plastic cap
forward while pulling
backrmlyonring.
Break off excess.
FOR METAL STUD WALLS ONLY:Drillfour1/2"
(13mm) dia. holes through drywall and studs at lo-
cations corresponding to wall plate. Insert togglers
(G) as shown below...
Skip to Step 2 page 7
G
Align wall plate with
hole in wall and
fasten using 1/4-20 x
2.5"screw(H).
wall plate
H
• Productmustbemountedthroughdrywallthathasa
minimumthicknessof1/2"andintometalstuds,26
gauge or heavier.
• Makesurethattogglersareanchoredintothecenter
ofthestudsasshowningure1.Theuseofan
"edgetoedge"studnderishighlyrecommended.
WARNING
H
B
G
STUD
1-1
1-2
1-3
1-4
1-5
1
3-6
Skip to Step 5
g.1

6 of 9 ISSUED: 03-02-11 SHEET #: 125-9192-1
Position wall plate (B) at desired position on wall.Use
wall plate (B), making sure that it is level, as a template
tomarkholes.Drillfour1/4"(6mm)dia.holestoamini-
mumdepthof2-1/2"(64mm).Concretemustbe2000
psi density minimum. Insert anchors (K)inholesush
withwallasshowningure1.3.Placewallplate(B) over
anchorsandsecurewithfour#14x2-1/2"(6mmx65
mm) wood screws (I)asshowningure1.4.Makesure
wall plate is level and tighten all fasteners.
Skip to Step 2 page 7
Installation to Solid Concrete and Cinder Block Wall
1
CUTAWAY VIEW
INCORRECT
concrete
plaster/
drywall
B
CORRECT
concrete
plaster/
drywall
B
concrete
wall
Drill holes and insert anchors
Place wall plate (B) over anchors and secure with
screws (I)
Tighten all fasteners
I
B
1
2
• Tightenwoodscrewsrmly,but do not overtighten.
Overtightening can damage the screws, greatly re-
ducing their holding power.
• Nevertighteninexcessof80in•lb(9N.M.).
WARNING
• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimumof1-3/8"ofactualconcrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
partoftheblock,generally1"minimumfromthesideoftheblock.CinderblockmustmeetASTMC-90specica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concretemustbe2000psidensityminimum.Lighterdensityconcretemaynotholdconcreteanchor.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-
ware and components.
WARNING
K
K
I
K
g1.3
g1.4
• Concreteanchorsarenot intended for attachment to
concrete wall covered with a layer of plaster, drywall,
orothernishingmaterialasshownbelow.Ifmount-
ing to concrete wall covered with plaster/drywall is
unavoidable,plaster/drywall(upto5/8"thick)must
be counterbored as shown below. Be sure concrete
anchors do not pull away from concrete when tight-
ening screws. If plaster/drywall is thicker than
5/8",customfastenersmustbesuppliedbyinstaller.
WARNING
CINDERBLOCK
SOLIDCONCRETE
B
3

7 of 9 ISSUED: 03-02-11 SHEET #: 125-9192-1
Using information provided in detail 1 secure two adapter brackets (L) to back of display using four M4 x 12 mm
phillips screws (D) or four M6 x 16 mm phillips screws (E).
NOTE: When using M4 x 12 mm phillips screws (D), #8 washers (C) are required.
NOTE: Adapter brackets (L)have2"ofverticaladjustmentasshownindetail1.
200 mm
100 mm
BOTTOM OF DISPLAY
200 mm x 100 mm HOLE
PATTERNSHOWNABOVE
400 mm
200 mm
2"OFVERTICAL 
ADJUSTMENT
2
L
L
D or E
C
BOTTOM OF DISPLAY
200 mm x 100 mm
200 mm x 200 mm
400 mm x 200 mm
3Using information in hole pattern detail secure cross support bracket (A) to adapter brackets (L) with four
1/4-20 nylock nuts (M).
M
A
DETAIL1
L
L

8 of 9 ISSUED: 03-02-11 SHEET #: 125-9192-1
MOUNTINGSURFACE
NOTSHOWNFORCLARITY
Position slots of adapter plate (A) onto the four
M5 x 12 mm serrated washer head socket pin
screws (J) attached to wall plate (B).
To secure wall plate (B) to adapter plate (A), attach two M5 x 12 mm serrated washer head socket pin screws
(J) through the slots on the sides of wall plate (B) and threaded holes of adapter plate (A). Tighten with the 4 mm
security allen wrench (F).
Attach four M5 x 12 mm serrated washer head
socket pin screws (J) to the holes on the sides of
wall plate (B) using the 4mm security allen wrench
(F)provided.
4
AttachingMountingBracketUsingHookOnOption
4-1
J
B
J
A
SLOT J
J
B
A
B
4-2
J
BOTTOM OF DISPLAY

9 of 9 ISSUED: 03-02-11 SHEET #: 125-9192-1
Attach two M5 x 12 mm serrated washer head
socket pin screws (J) to the bottom holes on the
sides of wall plate (B) using the 4mm security allen
wrench (F)provided.
Position slots of adapter bracket (A) onto the two
M5 x 12 mm serrated washer head socket pin
screws (J) attached to wall plate (B).
44-1
J
B
J
A
SLOT
B
AttachingMountingBracketUsingTiltOption
To secure wall plate (B) to adapter plate (A), adjust tilt as desired and attach two M5 x 12 mm serrated washer
head socket pin screws (J) into the slots on the sides of wall plate (A) and threaded inserts of adapter bracket (A).
Tighten with the 4 mm security allen wrench (F).
4-2
J
B
A
J
MOUNTINGSURFACE
NOTSHOWNFORCLARITY
BOTTOM OF DISPLAY
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.