PEERLESS LCC 18-C Guide

Features:
•Comes in two adjustable height ranges (in 1"
increments): 18"-30" and 36"-48"
•-5° to +20° adjustable tilt
•Screen can be mounted in standard position or
face-down
•Portrait or landscape orientation
•Ceiling plate included
•Hardware included for wood or concrete installa-
tions
•Snap-together cover provides sleek aesthetics
and cord management
•Theft resistant security fasteners included
•VESA®75/100 mm compliant (Non-VESA adapter
offered separately)
•Comes in black and silver
•360°swivelaction
Vertical
Position
Horizontal
Position
Models: LCC18-C, LCC18-CS, LCC36-C, LCC36-CS
Patent Pending
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation and Assembly:
Ceiling mount for LCD screens up to 29"
Max UL Load Capacity: 40 lb (18.1 kg)
©
UL
USC

2 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•phillips screwdriver
•drill with 1/4", 3/8", 5/32", and #46 drill bits
Table of Contents
Parts List ..............................................................................................................................................................................3
Installation to Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings ............................................4
Installation to Concrete Ceilings...........................................................................................................................................5
Installing Reducer ................................................................................................................................................................6
Flush Mount Installation .......................................................................................................................................................7
Installation to Threaded Rod ................................................................................................................................................7
Installation to Extension Column ..........................................................................................................................................8
Installation to Lightweight Suspended Ceiling Plate .............................................................................................................9
Attaching Tilt Bracket to LCD Screen.................................................................................................................................10
Installation of Plasma in the Vertical Position.....................................................................................................................11
Installation of Plasma in the Horizontal Position.................................................................................................................12
Installation of Vertical Covers.............................................................................................................................................13
Installation of Top Covers ..................................................................................................................................................13
Installation of Tilt Covers in the Vertical Position ...............................................................................................................14
Installation of Tilt Covers in the Horizontal Position ...........................................................................................................14
Forcustomer care call [phone] or
[phone].
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerlesscustomercareat1-800-729-0307.
• Thisproductshould only be installed by a qualifiedprofessional.
• Make sure that the ceiling will safely support the combined load of the equipment and all attached hardware and
components.
• Neverexceed the Maximum UL LoadCapacity of 40 lb (18.1kg).
• If mounting to wood ceiling joists, make sure that mounting screws are anchored into the center of the joists. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
WARNING
Accessories
•LightweightAdjustableSuspendedCeilingKit(CMJ500)
•LightweightSuspendedCeiling Kit (CMJ 455)
•Accessory Pack for CMJ 455 (ACC 455)*
•LightweightCathedralCeilingPlate(ACC912)*
•Unistrutor StructuralCeilingPlates(CMJ 300, CMJ 310)*
•Anti-VibrationCeiling Plates (ACC 845)*
•I-BeamClamps(ACC558,ACC559)
•TrussCeilingAdapter (ACC 557)*
•UnistrutAdapter (ACC 550)
•3/4"Pipe Reducer (ACC 913)*
•Fixed Length 1 1/2" Extension Columns
(EXT models)
•Adjustable Length 1 1/2" Extension Columns
(ADJ models)
•Extension Column Stabilizer Kit (ACC 050)*
•ExtensionColumnConnector(ACC109)
•1/2"ThreadedRod(ACC820)*
•ThreadedRodAdapter(ACC810)*
•Non-VESA®AdapterPlates (LC models)*
•handsaw
•carpenter's knife
*not evaluated by UL

3 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
D
F
E
G
H
I
J
KL
MNO
BC
P
A
Q
R
T
S
U
V
LCC 18-C LCC 18-CS LCC 36-C LCC 36-CS
Description Qty. Part # Part # Part # Part #
Atube assembly 1 055-1520 055-4520 055-1521 055-4521
Bceiling plate 1 580-1042 580-4042 580-1042 580-4042
Ctilt bracket 1 055-1551 055-4551 055-1551 055-4551
Dreducer 1 580-1009 580-4009 580-1009 580-4009
E#14 x 2.5" wood screw 2 5S1-015-C03 5S1-015-C04 5S1-015-C03 5S1-015-C04
FM5 x 12 mm socket pin screw 4 520-1064 520-2064 520-1064 520-2064
G4 mm security allen wrench 1 560-9646 560-9646 560-9646 560-9646
HAlligator® concrete anchor 2 590-0097 590-0097 590-0097 590-0097
I10-32 x 3/8" socket set screw 1 520-1127 500-2018 520-1127 500-2018
Jhex wrench 1 560-1034 560-1034 560-1034 560-1034
KM4 x 10 mm socket pin screw 4 520-1060 520-2060 520-1060 520-2060
LM4 x 12 mm serrated washer head socket pin screw 4 510-1079 510-2079 510-1079 510-2079
MM4 x 20 mm socket pin screw 4 520-1061 520-2163 520-1061 520-2163
N#10-32 x 3/16" slotted set screw 1 520-1187 520-2187 520-1187 520-2187
Oretaining spacer 4 590-5005 590-5003 590-5005 590-5003
PM5 x 10 mm socket pin F-type screw 1 520-1164 520-2031 520-1164 520-2031
Qvertical cover 2 590-1183 590-4183 590-1184 590-4184
Rtop cover 2 590-1185 590-4185 590-1185 590-4185
Stilting cover 2 590-1186 590-4186 590-1186 590-4186
T#4-24 x 3/8" flat head phillips screw 3 560-1715 560-4715 560-1715 560-4715
Ucable tie 3 590-1168 590-1168 590-1168 590-1168
Vsuper glue 1 600-0017 600-0017 600-0017 600-0017
Walcohol pad (not shown) 1 600-0018 600-0018 600-0018 600-0018
Parts List

4 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Drill two 5/32" (4 mm) dia. holes to a minimum
depth of 2.5" (64 mm). Attach ceiling plate (B)
with two #14 x 2.5" (6 mm x 65 mm) wood
screws (E) as shown using 3/8" (10 mm)
socket wrench. Tighten wood screws (E) so
ceiling plate (B) is firmly attached.
Skip to step 2 on page 6.
Installation to Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings
• Tighten wood screws so that ceiling plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into
the center of the joist. The use of an "edge to edge"
stud finder is highly recommended.
WARNING
E
E
B
WOOD
JOIST
CEILING

5 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation to Concrete Ceilings
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach ceiling plate (B) using two
concrete anchors (H) and #14 x 2.5" wood screws (E)
as shown in Illustration A and 1, 2, and 3 (below).
Tighten all fasteners.
E
Illustration A
B
CONCRETE
CEILING
1
3
Drill hole and insert anchor
Place ceiling plate over anchor and secure with screw
After repeating step one tighten all fasteners
concrete
ceiling
E
E
2B
CUTAWAY VIEW
INCORRECT
concrete
metal
bracket
plaster/
drywall
CORRECT
concrete
metal
bracket
plaster/
drywall
• Tighten wood screws firmly, but do not overtighten.
Overtightening can damage the bolt, greatly reducing
its holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
or other finishing material. If mounting to concrete
wall covered with plaster/drywall is unavoidable,
plaster/drywall (up to 5/8" thick) must be
counterbored as shown below. If plaster/drywall is
thicker than 5/8", custom fasteners must be supplied
byinstaller(notevaluated by UL).
WARNING
H
H
H
H

6 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Threadreducer(D)ontotube assembly(A)untiltight.
Insert set screw (I) into reducer as shown in figure 2-1.
Tighten screw using hex wrench (J).Note: Set screw (I)
is used to jam against the threads of tube assembly to
preventanyexcessmovement.
Toadjust height of tube assembly(A), remove socket pin
screw and two lock washers using 4 mm security allen
wrench (G) and adjust to desired height as shown in
figure2-2.
A
I
D
figure 2-1
Installing Reducer
B
Afigure 2-2
SOCKETPINSCREW
LOCKWASHERS

7 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Flush Mount Installation
B
D
Screw reducer (D) into ceiling plate (B) until notch
in reducer is aligned with one of the four holes in
ceiling plate and set screw (I) is at least partially
covered by ceiling plate as shown in figure 3-1.
Secure reducer with one M5 x 10 mm F-type socket
pin screw (P) using security allen wrench (G) as
shown in figure 3-2. Note:Slotted set screw (N) is
used to jam against the threads of the reducer to
prevent any excess movement of the tube
assembly (A). Do not overtighten screw;
overtightening screw will damage threads making it
difficult to separate the products.
Skip to step 4 on page 10.
I
figure 3-1
P
figure 3-2
SLOT
SLOT
D
ACC 810 (SOLD
SEPARATELY)
1/2 -13 THREADED
ROD
Screw threaded rod adapter (ACC 810)into extension
column connector (ACC 109). Align slot in threaded
rod adapter with one of the top holes in extension
column connector. Insert and tighten one #10-32 x 3/
8" socket pin screw provided with extension column
connector through extension column connector into
slot on threaded rod adapter using 4 mm security
allen wrench (G). See figure 3-3.
Align slot in reducer (D) to one of the bottom holes in
extension column connector. Insert and tighten one
#10-32 x 3/8" socket pin screw provided with
extension column connector through extension
column connector into slot in reducer. See figure 3-4.
Note:Slotted set screws provided with extension
column connector are used to jam against the threads
of each connecting joint to prevent any excess
movement. Do not overtighten screws; overtightening
screws will damage threads making it difficult to
separate the products.
Skip to step 4 on page 10.
SLOT
ACC 810
THREADED
ROD
ACC 810
THREADED
ROD
SLOT
D
Installation to
Threaded Rod
Accessory ACC 810 (not evaluated by UL),
threaded rod adapter, is required.
SOCKET
PIN
SCREW
ACC 109
SOCKET
PIN
SCREW
ACC 109
(SOLD
SEPARATELY) figure 3-3
figure 3-4
A
N
SET
SCREW
SET
SCREW
ACC 109

8 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation to Extension Column
Screwextensioncolumn(EXT or ADJ
Series) to ceiling plate (B). Align the notch
with one of the four holes in the ceiling plate
and secure extension column with a M5 x
10 mm socket pin screw (P) using security
allenwrench(G).Seefigure3-5.
Note:Slotted set screw (N) is used to jam
againstthethreadsofthereducertoprevent
anyexcess movement of the extension
column.Donotovertightenscrew;
overtighteningscrewwilldamagethreads
making it difficult to separate the products.
Screwextensioncolumnconnector
(ACC 109) to extension column. Align slot
in extension column with one of the top
holes in extension column connector. Insert
and tighten one #10-32 x 3/8" socket pin
screwprovidedwithprojectorthrough
extension column connector into slot on
extension column using security allen
wrench(G).Seefigure3-6.
Screwreducer (D)toextension column
connector.Align reducer to oneof the
bottom holes in extension column
connector.Insert andtightenone #10-32x
3/8"socketpin screw provided with
connectorthroughextensioncolumn
connector into slot in reducer using security
allenwrench(G).Seefigure3-7.
Note:Slottedset screws provided with
extension column connector are used to
jam against the threads of each connecting
jointto prevent anyexcessmovement.Do
notovertightenscrews;overtightening
screws will damage threads making it
difficulttoseparate the products.
Skip to step 4 on page 10.
B
SLOT
SLOT
SLOT
B
SLOT
figure 3-5
P
B
D
N
figure 3-6
figure 3-7
EXTENSION
COLUMN
CONNECTOR
(SOLD
SEPARATELY) SOCKET PIN
SCREW
SOCKET PIN
SCREW
EXTENSION
COLUMN
(UL Listed EXT or
ADJ Series)
Sold Separately
EXTENSION
COLUMN
EXTENSION
COLUMN
SET SCREW
SET SCREW
EXTENSION
COLUMN
ACC 109
ACC 850 - EXTENSION COLUMN
CONNECTOR WITH CORD MANAGEMENT
- MAY BE USED IN PLACE OF EXTENSION
COLUMN CONNECTOR. (SOLD
SEPARATELY)
ACC 109

9 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Installation to Lightweight Suspended Ceiling Plate
D
EXTENSION
COLUMN
SLOT
SLOT
EXTENSION
COLUMN
SLOT
D
Refer to instruction sheet for lightweight
suspended ceiling plate (CMJ 455) for
attachment of ceiling plate to ceiling.
Screw extension column (EXT or ADJ
Series) to retaining collar in ceiling tray.
Align the notch with one of the four
holes in retaining collar and secure
extension column with one M5 x 10 mm
socket pin screw (P) using security allen
wrench (G). See figure 3-8.
Note:Slotted set screw (N) is used to
jam against the threads of the reducer
to prevent any excess movement of the
extension column. Do not overtighten
screw; overtightening screw will
damage threads making it difficult to
separate the products.
Screw extension column connector to
extension column. Align slot in
extension column with one of the top
holes in extension column connector.
Insert and tighten one 10-32 x 3/8
socket pin screw provided with
connector through extension column
connector into slot on extension column
using security allen wrench. See figure
3-9.
Screw reducer (D) to extension column
connector. Align slot in reducer to one
of the bottom holes in extension column
connector. Insert and tighten one 10-32
x 3/8 socket pin screw provided with
connector through extension column
connector into slot in reducer using
security allen wrench. See figure 3-10.
Note:Slotted set screws provided with
extension column connector are used to
jam against the threads of each
connecting joint to prevent any excess
movement. Do not overtighten screws;
overtightening screws will damage
threads making it difficult to separate
the products.
P
EXTENSION
COLUMN (SOLD
SEPARATELY)
RETAINING COLLAR
LIGHTWEIGHT
SUSPENDED
CEILING PLATE
(SOLD SEPARATELY)
N
SOCKET PIN
SCREW
ACC 109
ACC 109
SOCKET PIN
SCREW
figure 3-8
figure 3-9
figure 3-10
SET SCREW
SET SCREW
EXTENSION
COLUMN
CONNECTOR
(SOLD
SEPARATELY)
EXTENSION
COLUMN
(UL Listed EXT or
ADJ Series)
Sold Separately
ACC 850 - EXTENSION COLUMN
CONNECTOR WITH CORD
MANAGEMENT - MAY BE USED IN PLACE
OF EXTENSION COLUMN CONNECTOR.
(SOLD SEPARATELY)

10 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Note:LCD screen may
appear slightly different
than illustrated.
C
FORVESA75MOUNTINGPATTERN:
1) Choose hole pattern indicated below. 2) Attach tilt bracket (C) to back of screen using four M4 x 10 mm screws (K) as
indicated below. 3) If hole pattern is in a pocket, attach tilt bracket to back of screen using four M4 x 20 mm screws (M)
and four retaining spacers (O) as indicated below. Tighten all security screws with security allen wrench (G).
FORVESA100MOUNTINGPATTERN:
1) Choose hole pattern indicated below. 2) Attach tilt bracket (C) to back of screen using four M4 x 10 mm screws (K)
as indicated below. Tighten all security screws with security allen wrench (G).
Note:If installingLCDscreen modelSharp®LC-13E1U,LC-15E1U, LC-20E1U,orif youdon'tget threecompleteturns
in the screen inserts, use four M4 x 12 mm screws (L) instead of four M4 x 10 mm screws (K).
Note: This product is designed to accommodate screens with VESA®compliant hole patterns. For safe
mounting, please make sure that mounting screws turn at least three complete turns in the screen inserts.
C
Note:LCD screen may
appear slightly different
than illustrated.
Attaching Tilt Bracket to LCD Screen
BOTTOM OF SCREEN
BOTTOM OF SCREEN
For screens with a hole
pattern in a pocket,
spacers (O) go between
tilting bracket (C) and
screen.
K
K

11 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
3/16"
EXPOSED
THREAD
Installation of Screen in the Vertical Position
Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5-1). Leave approximately
3/16" of thread exposed (see figure 5.2).
COLUMN
BRACKET F
Hook tilt bracket (C) onto column bracket (see figure 6-1). Secure with two M5 screws (F) (see figure 6-2). Adjust tilt
(20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).
Note: Cable ties (U) are provided for optional cord management.
COLUMN
BRACKET
C
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the LCD screen.
WARNING
F
fig. 5-1 fig. 5-2
fig. 6-1 fig. 6-2

12 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
3/16"
EXPOSED
THREAD
Installation of Screen in the Horizontal Position
Insert two M5 x 12 mm screws (F) into column bracket of tube assembly (A) (see figure 5-1). Leave approximately
3/16" of thread exposed (see figure 5-2).
COLUMN
BRACKET
Hook tilt bracket (C) onto column bracket (see figure 6-1). Secure with two M5 screws (F) (see figure 6-2). Adjust tilt
(20° forward and 5° back) and swivel to desired position. Tighten all screws using security allen wrench (G).
Note: Cable ties (U) are provided for optional cord management.
COLUMN
BRACKET
C
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the LCD screen.
WARNING
F
F
fig. 5-1 fig. 5-2
fig. 6-1
fig. 6-2

13 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Routecords throughsidechannels ofonevertical cover(Q).Snaptwo verticalcoverstogether ontubeassembly (A)so
that they are perpendicular to tilt bracket (C). If necessary, use a handsaw to cut vertical covers to match the length of
tube assembly.
Q
A
SIDE
CHANNELS
C
Snaptwo top covers (R) together flushwith finished ceiling. Use holes intop covers to mark vertical covers(Q).Using
a#46 (approx. .0810") drill bit,drill holes in vertical covers. (Note: It may benecessary to remove vertical covers
beforedrillingholesto avoiddamagingcables.) Removetopcovers (R).Useglue (V)onthe insideedgeof oneofthe
two top covers (R) so that the two sides will stick together when they are connected. Secure top covers to vertical
covers using two #4-24 x 3/8" flat head phillips screws (T) as shown in figure 8-1.
Note:One extra flat head phillips screw (T) hasbeenprovided.
Note: Alcohol pad (W) may be used for clean up of glue.
Installation of Top Covers
Installation of Vertical Covers
R
QT
fig.8-1

14 of 14 ISSUED: 09-27-04 SHEET #: 100-9005-5 03-10-09
Using a carpenter's knife, cut out any sections of tilt covers (S) necessary to allow them to snap together over vertical
covers (Q) as shown in figure 9-1. Note: Cut out sections of one tilt cover should mirror cut out sections of the other.
Use glue (V) on the inside edge of one of the two tilting covers (S) so that the two sides will stick together when they
are connected. Insert tabs of tilt covers into slots of tilt bracket (C) and snap tilt covers together.
Note: Alcohol pad (W) may be used for clean up of glue.
© 2004 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Installation of Tilt Covers in the Vertical Position
Installation of Tilt Covers in the Horizontal Position
Using a carpenter's knife, cut out any sections of tilt covers (S) necessary to allow them to snap together over vertical
covers (Q) as shown in figure 9-1. Note: Cut out sections of one tilt cover should mirror cut out sections of the other.
Use glue (V) on the inside edge of one of the two tilting covers (S) so that the two sides will stick together when they
are connected. Insert tabs of tilt covers into slots of tilt bracket (C) and snap tilt covers together.
Note: Alcohol pad (W) may be used for clean up of glue.
fig.9-1
S
C
Q
S
Q
fig.9-1
C