PEERLESS WSP 490 Guide

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 07-26-05 SHEET #: 024-9009-2 12-01-06
Installation and Assembly:
External Wall Plate
Model: WSP 490, WSP 490-S
Max Load Capacity: 80 lb (36.3 kg)

2 of 5 ISSUED: 07-26-05 SHEET #: 024-9009-2 12-01-06
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•studfinder("edgetoedge"studfinderisrecommended)
•phillipsscrewdriver
•drill with 1/2" drill bit
Forcustomercarecall(800)729-0307or(708)865-8870.
• Donotbegin to install your Peerless product until you have read and understood the instructions and warnings
containedinthis Installation Sheet. If you have any questions regarding any of the instructionsorwarnings,please
callPeerless customer care at1-800-729-0307.
• Thisproduct should only be installed by aqualifiedprofessional.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardwareandcomponents.
• Neverexceedthe Maximum Load Capacity of 80 lb (36.3kg).
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screwsfirmly, but donotovertighten. Overtightening can damagetheitems, greatly reducing their holding
power.
WARNING

3 of 5 ISSUED: 07-26-05 SHEET #: 024-9009-2 12-01-06
WSP 490 WSP 490-S
Description Qty. Part # Part #
Awall plate 1 024-1041 024-2041
B1/4-20 x .5" flat head phillips screw 2 520-1209 520-2178
Ctoggler 4 560-9708 560-9708
D1/4-20 x 2.5" phillips screw 4 520-9521 520-9522
Ewasher 4 540-9440 540-9444
Parts List
E
D
C
A
B
Note: Screws (B) are used to
attach mount to wall plate.

4 of 5 ISSUED: 07-26-05 SHEET #: 024-9009-2 12-01-06
C
Rotatetoggler
clockwise to
wedgeit
againstinside
walls of metal
stud.
Push into
hole.
Pivotend of
toggler.
Slide plastic
capforward
whilepulling
back firmly on
ring.
Breakoff
excess.
Note: Wall plate (A) can be mounted on 24", 20", or 16"
centers.
Using a stud finder, locate and mark the edges of the
metal stud used in mounting this product. Use of an
edgeto edge stud finder is highly recommended.
Use a level to draw a vertical line down the center of
the stud. Use wall plate (A) as template to mark
center of slots along the vertical line. Drill four 1/2"
(13 mm) dia. holes through drywall and studs. Insert
togglers(C)as shown below.
1
C
∅ 1/2"
(13 mm)
• Makesurethat mounting screws are anchored into
the center of the studs. The use of an "edge to edge"
studfinder is highly recommended.
WARNING

5 of 5 ISSUED: 07-26-05 SHEET #: 024-9009-2 12-01-06
2Attach wall plate (A) to togglers (C) with 1/4-20 x 2.5" flat head phillips screws (D), and washers (E).
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardwareandcomponents.
WARNING
A
E
D
C
©2005PeerlessIndustries,Inc. Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.