PEERLESS DS 35 Guide

1 of 3 ISSUED: 5-25-95 SHEET #: 081-9001-3 08-17-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
Parts may appear slightly different than illustrated.
Installation and Assembly - VCR Mount Models: DS 35, DS 35-SV, DS 35S, DS 35S-SV,
DS 40, DS 40-SV, DS 40S, DS 40S-SV, DS 40W,
DS 45, DS 45-SV, DS 45S, DS 45S-SV
INSIDEDIMENSIONS
MODEL# WIDTH (W) HEIGHT(H)
DS 35, DS 35-SV, DS 35S, DS 35S-SV 10.25" - 14.25" (260 mm - 362 mm) 2.69" - 4.5" (68 mm - 114 mm)
DS 40, DS 40-SV, DS 40S, DS 40S-SV, DS 40W 13.25" - 17.25" (337 mm - 438 mm) 2.69" - 4.5" (68 mm - 114 mm)
DS 45, DS 45-VS, DS 45S, DS 45S-SV 13.25" - 17.25" (337 mm - 438 mm) 4.25" - 5.75" (108 mm - 146 mm)
Check parts list. Be sure all parts listed are included with your product.
O
L
M
N
Q
P
D
• Do not use spring plate when attaching VCR mount to
TVmount/stand.Step one on page2illustratesproper
installation.
WARNING SPRING
PLATE
B
DS 35
DS 35-SV
DS 35S
DS 35S-SV
DS 40
DS 40-SV
DS 40S
DS 40S-SV
DS40W
DS 45
DS 45-SV
DS 45S
DS 45S-SV
Description Qty. Part Number
xxxxxx xx xxxxAshort piece of adhesive foam (not shown) 2 599-1122
x570-0014
xxx x xxBwasher 1 540-1007
x x x x x x x 540-2007
xxxxxx xx xxxxClong piece of adhesive foam (not shown) 2 599-3802
x570-0015
-- -- -- -- -- -- -- -- -- -- -- -- -- DVCRmount 1
xxx x xxLplastic spacer 2 540-9413
x x x x x x x 540-9443
xxxxxx xx xxxx xMM5 x .8 x 16 mm phillips screw 3 520-9515
xxx x xxN#10 SAE flat washer 7 540-9400
x x x x x x x 540-9442
xxx x xxO10-24 nylock nut 4 530-9341
x x x x x x x 530-9342
xxx x xxP10-24 x 1/2" carriage bolt 4 520-9523
x x x x x x x 520-2104
xx xx xxQM5 x 1" penta-pin™tool 1 520-9249
Parts List

2 of 3 ISSUED: 5-25-95 SHEET #: 081-9001-3 08-17-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
A
C
Adjust height + width.
MountVCR.
2 3
Attachfoampads(A)
and(C)asshown.
M
N
L
This VCR mount can be used with two different types of TV mounts/stands. As a result, you will not use all of the
fasteners provided. Follow the instructions for the type of TV mount/stand you have.
All other parts shown are found with TV mount/stand.
If you have the TV mount/stand pictured below and the mount is
already assembled, it will have to be disassembled to do this
installation.
Assemble the
parts as shown.
1
1
Use parts L, N, & M for this installation.
TV does not need to be removed for this installation.
Assemble the
parts as shown.
There are two small holes, on the bottom of the bar that runs
underneath the tray. If you do not see them, the bar was probably
installed upside down when the TV mount/stand was assembled.
You will need to remove the tray and the bar to turn it around so that
the holes face downward.
IMPORTANT: Be sure to reuse carriage bolt, brass washer
and lock nut included with wall mount.
CARRIAGEBOLT
BRASSWASHER
LOCKNUT
B
D

3 of 3 ISSUED: 5-25-95 SHEET #: 081-9001-3 08-17-04
Visit the Peerless Web Site at www.peerlessindustries.com For customer service call 1-800-729-0307 or 708-865-8870.
Insert four carriage bolts (P) into slots in upper VCR
mount.Attach lower VCR mount using four nuts (O)
andfour washers(N).HAND TIGHTEN ONLY.
Note:Ifadhesivepads onVCR Mountare covering
slots, trim away excessive pad to expose slots.
InsertVCR into upper VCRMount.
Alignfront of VCR with front of TV on TV Mount
(TVMount not pictured).Tighten expansion
screws in sides and bottom of VCR Mount to
clamp the VCR with a firm, secure grip.
Note: To access the vertical expansion screws
located on the bottom of the upper VCR Mount,
slide the lower VCR Mount to the side exposing
verticalexpansionscrew.Repeatthisstep on
oppositeside of VCR Mount.Center lower VCR
Mount and tighten four nuts (O, see step 4)
securely.
Expand lower VCR Mount to slightly larger than
the height and width of the VCR that it will hold.
Insertand clamp lower VCRintolower VCR
Mount.
P
N
O
OPTIONAL: If attaching multiple VCR mounts to a TV mount, proceed with step 4 through 6.
4
5
6
ADHESIVEPAD
SLOTS
©2004PeerlessIndustries,Inc. Allrightsreserved.PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
EXPANSION
SCREW
EXPANSION
SCREW
• Do not stack more than three VCR Mounts from a single Peerless TV Mount. Stacked load cannot exceed 50 lb (23
kg).
WARNING