PEERLESS RTPLA 50 Guide

Models: PLA 50-UNL, PLA 50-UNL-S,
PLA 50-UNLP, PLA 50-UNLP-S,
RTPLA 50, RTPLA 50-S
Installation and Assembly - Universal Articulating
Swivel Arm for 32" - 50" Plasma Screens
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Maximum Load Capacity:150 lb (68 kg)

2 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Tools Needed for Assembly
•studfinder ("edge to edge"studfinderis recommended)
•drill
•3/16" drill bit for wood studs
•5/16" masonry drill bit for concrete
•7/16"socket wrench with extension (recommended)
• 10 mm socket wrench for concrete anchors
•level
•phillipsscrewdriver
Accessories
•External Wall Plate (WSP716, WSP716-S, WSP724,
WSP724-S)
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Double Wood Stud Wall..................................................................................................................................6
Installation to Solid Concrete or Cinder Block .......................................................................................................................7
• Donot begin to install yourPeerlessproductuntilyou have read and understoodtheinstructionsandwarnings
containedin this Installation Sheet. If youhaveanyquestionsregarding any of the instructionsorwarnings,please
callPeerlesscustomercareat1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Makesure that the supportingsurfacewillsafely support the combined loadoftheequipment and all attachedhard-
wareandcomponents.
• NeverexceedtheMaximum Load Capacity. See pageone.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgetoedge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrewsfirmly,butdonotovertighten.Overtighteningcandamagetheitems, greatly reducing their holding
power.
• Thisproductisintendedforindooruseonly.Useofthisproductoutdoorscouldleadtoproductfailureandpersonalinjury.
• Thisproductwas designed and intended to be mounted tothefollowingsupportingsurfacescheckedbelowwiththe
hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-
ingsurface,contactPeerlesscustomercareat1-800-865-2112.
• This product was designed to be installed on the following wall construction only;
WALLCONSTRUCTION ADDITIONALHARDWAREREQUIRED
xWoodStud None
xWoodBeam None
xSolidConcrete None
xCinderBlock None
MetalStud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
Brick ContactCustomer Service
Otheror unsure? Contact CustomerService
WARNING

3 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
MODEL MODEL
PLA50-UNL RTPLA50-S
PLA50-UNLP PLA50-UNL-S
RTPLA 50 PLA 50-UNLP-S
DESCRIPTION QTY. PART# PART#
Awallplate 1 201-1095 201-4095
Btilt-roll assembly 1 201-1093 201-4093
Carmassembly 1 201-1094 201-4094
Dwallsupportarmaxle 1 201-1041 201-1041
Evinyltrim 3 600-1012 600-1012
FM10 x 1.5 x 15 mm screw bolt 8 520-9262 520-9262
G.505 x .75 x .062" nylon washer 1 540-1074 540-1074
Htilt adjustment knob 1 560-0108 560-0108
Icarriage bolt 3/8"-16 x 3.25" 1 520-1315 520-1315
J1.525 x 2 x .062" delrin washer 2 540-1070 540-1070
K#8-32 x .375" socket head cap screw 1 520-1210 520-1210
Lplastic finishing cap 8 590-1123 590-1123
Mholdingpin 1 580-1166 580-1166
Nretainerplug 1 590-1007 590-1007
O5/16 x 3" wood screw 6 520-1243 520-1243
P.250 x 1 x .068" washer 6 540-1063 540-1063
Q9/64"allenwrench 1 560-9728 560-9728
Rcablemanagementclips 4 590-1166 590-1166
Scable tie 4 590-1168 590-1168
T36"polyestermeshsleeve 1 600-1015 600-1015
U6mmallenwrench 1 560-9716 560-9716
Wanchor 6 590-1025 590-1025
O
F
E
Before you start make sure all parts
listed are included with your product.
Wall Mount Parts List A
Some parts may appear slightly different than illustrated.
B
C
D
H
M N
S T
G
RU
Q
JI K L
P
W

4 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
DD
CCBBAA
RTPLA50 RTPLA50-S
PLA 50-UNL PLA 50-UNL-S PLA 50-UNLP PLA 50-UNLP-S
Description Qty Part # Part # Part # Part #
AA adapter bracket 1 201-1110 201-4110 201-1110 201-4110
BB shallow adapter bracket 2 201-1511 201-4511 201-1514 201-4514
CC deep adapter bracket 2 201-1510 201-4510 201-1513 201-4513
DD allen wrench 1 560-9646 560-9646 560-0072 560-0072
Before you begin, make sure all parts shown are included with your product.
Adapter Bracket Parts List

5 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
M5 x 25 mm (4)
520-1122
M4 x 12 mm (6)
510-1079
M4 x 25 mm (4)
510-1082
M5 x 12 mm (4)
520-1064 M6 x 12 mm (4)
520-1050
M6 x 25 mm (4)
520-1211 multi-washer(6)
580-1036
SecurityAdapter Bracket Fasteners
M6 x 20 mm (4)
520-9554
M6 x 30 mm (4)
520-1067
M8 x 15 mm (6)
520-1068
M8 x 40 mm (4)
520-1152
M8 x 25 mm (4)
520-1101
M6 x 20 mm (4)
520-9402
M6 x 30 mm (4)
510-9109 multi-washer(6)
580-1036
M8 x 16 mm (6)
520-9257
M8 x 40 mm (4)
520-1136
M4 x 12 mm (6)
504-9013
Phillips Adapter Bracket Fasteners
M4 x 25 mm (4)
504-1015
M5 x 12 mm (4)
520-1027 M5 x 25 mm (4)
520-9543
M6 x 12 mm (4)
520-1128
M6 x 25 mm (4)
520-1208
I.D. .22" (5.6 mm) (4)
540-1057
M8 x 25 mm (4)
520-1031
I.D. .34" (8.7 mm) (4)
540-1059
I.D. .22" (5.6 mm) (4)
540-1057 I.D. .34" (8.7 mm) (4)
540-1059

6 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
• Installermustverify that the supporting surface willsafely support the combinedload of the equipmentand all attached
hardwareand components.
• Tightenwoodscrews so that wall plate is firmlyattached, but do not overtighten.Overtightening can damage the
screws,greatlyreducingtheirholdingpower.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Do not attach directly to a metal stud wall. Use of a triple stud WSP wall plate is required for attachment to metal
studs (contact customer care).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovidedisfor attachment of mount through standard thickness drywall or plasterinto wood studs. Installers
areresponsibletoprovidehardwarefor other types of mounting situations.
• Neverexceedthe Maximum Load Capacity of 150 lb(68 kg).
1
WARNING
Installation to Wood Stud Wall
Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.
Useof an edge-to-edge studfinder ishighly recommended. Basedon theiredges, drawa vertical linedown each
stud’s center. Place wall plate on wall as a template. The top mounting slots should be located 3.9" below the
desired screen center. Level plate, and mark the center of the four mounting holes. Make sure that the mounting
holes are on the stud centerlines. Drill six 3/16" (5 mm) dia. holes 3" (76 mm) deep. Make sure that the wall plate is
level, secure it using six 5/16 x 3" wood screws (O) and washers (P).
Skip to step 2 on page 8.
A
O
P
• Never mount this product to metal studs without the
requiredaccessory.
WARNING

7 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Make sure that wall plate (A) is level, use it as a
template to mark six mounting holes. The top mounting
slots should be located 3.9" below the desired screen
center. Use the masonry bit to drill six 5/16" (8 mm) dia.
holes to a minimum depth of 1.75" (45 mm). Attach wall
plate (A) using concrete anchors (W) and washers (P) as
shownin1-1through1-4.
Align hole in wall plate (A) with hole in wall. Gently
hammerinconcrete anchor as shown.
Usea10mm wrench (not provided) to tighten concrete
anchors (W) to 80 in • lb(9 N.M.) maximum torque as
shown.
1
1-1
1-2
1-1
1-3
A
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Neverattachconcreteexpansionanchorstoconcrete
coveredwithplaster, drywall or other finishing material.
WARNING
• Tightenconcrete anchor bolt firmly, but do not over-
tighten.Overtighteningcandamagethebolt,greatly
reducingitsholding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
WARNING
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Makesure that the supportingsurface will safelysupport thecombined loadof the equipmentand allattached hard-
wareand components.
• Neverexceedthe Maximum Load Capacity of 150 lb(68 kg).
Installation to Concrete Wall
P
1-4
1-2
concrete
surface
Drill hole(s) and insert anchor(s) (W)
mounting
plate
Place plate over anchor(s) (W) and secure with screw(s)(O)
Tighten all fasteners
W
W
W
O
CUTAWAYVIEW
INCORRECT CORRECT
mounting
plate
plaster/
drywall
concrete mounting
plate concrete
plaster/
drywall

8 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Snap four cable management clips(R)into top or bottom of arm assembly(C)as shown.Cable ties (S) are used with
clipsforcordmanagement.
Slide one mesh sleeve (T) over each cable. Use cable ties (S) to tighten mesh sleeves to cables.
NOTE: There are five mounting positions. The
center position is shown (right). Slidewasher(J)
over wall support arm axle (D). Next, insert plastic
cap (N) into axle. Then, insert holding pin (M) into
axle. See detail 1.
NOTE: Fit of axle (D) into wall plate (A) and arm
assembly (C) will be tight. Gently tap into place
with a hammer if necessary.
R
S
C
2
3
2-1
T
3-1
KD
Insert socket cap screw (K) into hole at bottom of
wall support arm axle (D) as shown in detail 3.
Tightenscrewusing9/64"allenwrench(Q).
N
J
D
M
J
C
DETAIL 3
ADETAIL 1
Place arm assembly (C) with washer (J) into wall
plate (A). Insert axle assembly shown in detail 1
throughwallplate (A), arm assembly (C), and
washer (J). Lock axle in place by aligning holding
pin (M) with notches shown in detail 2.
2-2 NOTCH
DETAIL 2
• If you are uncertain that product is properly installed, call customer care.
WARNING

9 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
BI
F
Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).Attach tilt-roll assembly to adapter bracket (AA)
with four M10 socket screws (F). Tighten screws using 6 mm allen wrench (U).
• Donot overtighten screws!Overtighteningmayhinder
rolloption.
CAUTION
4
5
Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm
assembly(C).
4-1 Insertone finishing cap (L) intoeach unused holeof wall plate (A).
L
A
E
C
SWIVELBOX
AA

10 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.
Hook tilt-roll assembly (B) onto M10 screws (F).
Insert carriage bolt (I) into slot of swivel box as
shown in figure 6.1. Install nylon washer (G) and tilt
adjustmentknob (H).
Install remaining two M10 screws (F) as shown in
figure6.2. HAND TIGHTEN all four M10 screwsto
allowfortilt adjustment. Remove tape from carriage
bolt (I). For tilt adjustment, push back on the top of
plasma to relieve pressure on knob.Adjust tilt to
desired position and tighten tilt adjustment knob (H),
then securely tighten all four M10 screws (F) using
6mm allen wrench (U).
.25"
F
• Use an assistant or mechanical lifting equipment to safely lift and position the plasmaTV.
WARNING
• After tilt is adjusted, all fasteners must be tightened.
Failure to do so will result in damage to the mount.
CAUTION
I
BF
HH
F
I
G
6
6-1
6-2
fig. 6.1 fig. 6.2
SWIVELBOX
SWIVELBOX C
Adapter bracket not shown for clarity. Adapter bracket not shown for clarity.

11 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Note: "X"dimensionsshouldbeequal.
Installing Adapter Brackets
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown below.
Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers and
spacersas shown in figure7.1 andfigure 7.2.
NOTE: Top and bottom holes must always be used.
Verify that all holes areproperly aligned, and thentighten screws using a phillipsscrewdriver.
NOTE: Ifusingsecurity screws, tighten using security allen wrench(DD).
MEDIUMHOLEFORM5SCREWS
SMALLHOLEFORM4SCREWS
LARGEHOLEFORM6SCREWS
BB
or
CC
CENTERBRACKETSVERTICALLY
ONBACKOFSCREEN
X
X
Notes:
• Thenumber of fasteners used will vary,
dependinguponthetypeofscreen.
• Multi-washers and spacers may not be
used,dependinguponthe type of screen.
• Use the corresponding hole in the multi-
washer that matches your screw size as
shown.
MULTI-WASHER
7
NOTE: For flat back screens proceed to step 7-1. For bump-out or recessed back screen skip to step 7-2.
• Tightenscrewsso adapter brackets are firmly attached. Donot tighten with excessive force.Overtightening can cause
stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING

12 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2
for a full screen compatibility chart for this mount.
Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown
below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten.
If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack.
Repeatfor remaining mounting holes,level brackets andtighten screws.
NOTE: Spacers may not be used,depending upon thetype of screen.
Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2
for a full screen compatibility chart for this mount.
Beginwith longer length screw, handthread throughmulti-washer, adapter bracket and spacer in that orderinto
screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do
not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled
fastenerpack. Repeat for remainingmounting holes,level bracketsand tighten screws.
For Flat Back Screen
For Bump-out or Recessed Back Screen
SCREEN
MULTI-WASHER
SCREW
ADAPTER
BRACKET
(BBORCC)
fig. 7.2
SPACER
fig. 7.1
7-1
7-2
ADAPTER
BRACKET
(BBORCC)
SCREEN
MULTI-WASHER
SCREW
Ifyouhaveanyquestions, please call Peerless customer care at 1-800-865-2112.
Ifyouhaveanyquestions, please call Peerless customer care at 1-800-865-2112.

13 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Mounting and Removing Flat Panel Screen
Referto mount instruction sheetfor attachmentof adapterbracket tomount.
Hook adapter brackets (BB or CC) onto adapter bracket (AA), then slowly swing screen in as shown. Turnscrews
clockwiseatleastsixtimestopreventscreenfrombeingremovedasshownindetail4.Tightenusingallenwrench(DD).
Screen can be adjusted horizontally if desired.
NOTE:To lock the screen down, tighten screws to adapter bracket as shown in detail 4.
Toremovescreen frommount, loosenscrews,swing screenaway frommount,andliftscreenoffofmount.
8
AA
BB or CC
DETAIL 4
SCREWS
AA
BB
or
CC
• Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television.
WARNING

14 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
If it is too difficult to adjust roll of plasma, loosen screws shown in figure 9.1 using a phillips screwdriver.
IMPORTANT! Do not loosen or tighten screws more than 1/8 turn.
Depending on the specific size & weight of the plasma, articulating swing arm may be angled at different positions,
causing plasma to appear to lean sideways at different articulating positions. Tilt-roll assembly (B) allows plasma to
be manually adjusted, so plasma can be horizontal at all positions.To adjust, gently rotate plasma by hand to desired
position.
9
9-1
ARTICULATINGARM
PLASMA
fig. 9.1
©2007,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
ROLL
ADJUSTMENT
SCREWS

15 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Installation et montage - Support mural articulé
universel pour écrans plasma de 32 à 50 po
Capacité de charge maximale :150 lb (68 kg)
3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
Modèles : PLA 50-UNL, PLA 50-UNL-S,
PLA 50-UNLP, PLA 50-UNLP-S,
RTPLA 50, RTPLA 50-S

16 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Outils nécessaires au montage
•localisateurde montants (un localisateurde montants« bord àbord »
estrecommandé.)
•perceuse
•foret de 3/16 po pour montants en bois
•foretà maçonnerie de 5/16po pour béton
•cléà douille de 7/16 poavec extension (recommandé)
•llave de copa de 10 mm para anclajes para concreto
•niveau
•tournevisPhillips
Accessoires
•Plaquemuraleextérieure(WSP716,
WSP716-S, WSP724, WSP724-S)
Remarque : lisez entièrement la fiche d’instructions avant de commencer l’installation et l’assemblage.
• Ne commencez pas à installer votre produit Peerless avant d’avoir lu et assimilé les instructions et les mises en garde
contenues dans cette fiche d’installation. Pour toute question concernant les instructions ou les mises en garde,
appelezleserviceàlaclientèledePeerlessau1-800-865-2112.
• Ceproduitne doit être installé que par une personneayant de bonnes aptitudes en mécanique,expérimentée en
travauxdeconstructionélémentaires,et démontrant une parfaite compréhension de ces instructions.
• Assurez-vousquelasurface de support pourra soutenir sans danger la charge combinéede l’équipement, de toute sa
visserie et de tous ses composants.
• Ne dépassez jamais la capacité de charge maximum. Reportez-vous à la page 15.
• Si vous effectuez le montage sur un mur à montants en bois, assurez-vous que les vis de montage sont ancrées au
centre des montants. L’usage d’un localisateur « bord à bord » est fortement conseillé.
• Pourleveretpositionnerl’équipemententoutesécurité,faites-vous toujours aider par une autre personne ou utilisez
unmatériel de levage mécanique.
• Serrez fermement les vis, mais sans excès. Un serrage excessif peut endommager les éléments et en réduire
considérablementle pouvoir de maintien.
• Este productoestádiseñado parauso eninterioressolamente. Utilizar esteproducto enexteriorespodría causarfallas
delproductoylesionesaindividuos.
• Ce produit a été conçu et prévu pour être monté sur les surface de support mentionnées ci-après ; la visserie incluse
dans ce produit est celle spécifiée sur la fiche d’installation. Pour monter ce produit sur une autre surface de support,
adressez-vousau service clientèle dePeerlessau1-800-865-2112.
• Ce produit a été conçu pour être installé sur le type de mur suivant uniquement :
TYPEDE MUR VISSERIESUPPLÉMENTAIREREQUISE
xMontantenbois Aucune
xPoutreenbois Aucune
xBétonplein Aucune
xBlocdebétonde mâchefer Aucune
Montantmétallique Ne fixer qu’avec le kit d’accessoires Peerless pour montants métalliques
Adressez-vousauserviceclientèlepourvousprocurerlekitd’accessoires
Peerlesspourmontantsmétalliques.
Brique Adressez-vousau service clientèle
Autre, ou vous n’êtes pas sûr ? Adressez-vousau service clientèle
AVERTISSEMENT
Table des matières
Liste des pièces .................................................................................................................................................................17
Installation sur un mur à doubles montants en bois ............................................................................................................20
Installation sur du béton plein ou un bloc de béton de mâchefer .........................................................................................21

17 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
Liste des pièces du support mural
Certaines pièces peuvent différer légèrement de l’illustration.
RTPLA50-SRTPLA50
PLA50-UNL PLA50-UNL-S
PLA50-UNLP PLA50-UNLP-S
DESCRIPTION Qté Pièce nº Pièce nº
Aplaquemurale 1 201-1095 201-4095
B support inclinable et rotatif 1 201-1093 201-4093
Cbrasarticulé 1 201-1094 201-4094
Daxedusupportmural 1 201-1041 201-1041
Ebordureenvinyle 3 600-1012 600-1012
Fboulon à vis M10 x 1,5 x 15 mm 8 520-9262 520-9262
Grondelle 0,505 x .75 x 0,062 po 1 540-1074 540-1074
Hmolette 1 560-0108 560-0108
Iboulon 3/8 -16 x 3,25 po 1 520-1315 520-1315
Jrondelle 1,525 x 2 x 0,062 po 2 540-1070 540-1070
Kvis d’assemblage à tête creuse 1 520-1210 520-1210
Lemboutdefinitionen plastique 8 590-1123 590-1123
Mtige de fixation 1 580-1166 580-1166
Nbouchondesûreté 1 590-1007 590-1007
Ovis à bois de 5/16 x 3 po 8 520-1243 520-1243
Prondelle de 0,250 x 1 x 0,068 po 8 540-1063 540-1063
Qcléhexagonale de 9/64 po 1 560-9728 560-9728
Rserre-câble 4 590-1166 590-1166
Sattache de câble 4 590-1168 590-1168
Tenveloppeenmaillepolyester 1 600-1015 600-1015
Uclé hexagonale de 6 mm 1 560-9716 560-9716
Wchevilled’ancrage 6590-1025 590-1025
O
F
E
A
B
C
D
H
M N
S T
G
RUQ
JI K L
P
Avant de commencer, veuillez vous
assurer que toutes les pièces
énumérées sont incluses.
W

18 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
DD
CCBBAA
PLA 50-UNL PLA 50-UNL-S PLA 50-UNLP PLA 50-UNLP-S
RTPLA50 RTPLA50-S
Description Qté Pièce nº Pièce nº Pièce nº Pièce nº
AA support adaptateur 1 201-1110 201-4110 201-1110 201-4110
BB support adaptateur peu profond 2 201-1511 201-4511 201-1514 201-4514
CC support adaptateur profond 2 201-1510 201-4510 201-1513 201-4513
DD clé hexagonale 1 560-9646 560-9646 560-0072 560-0072
Avant de commencer, veillez à ce que toutes les pièces énumérées soient incluses.
Liste des pièces

19 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
M5 x 25 mm (4)
520-1122
M4 x 12 mm (6)
510-1079
M4 x 25 mm (4)
510-1082
M5 x 12 mm (4)
520-1064 M6 x 12 mm (4)
520-1050
M6 x 25 mm (4)
520-1211 rondelletout usage(6)
580-1036
Fixations de sécurité du support adaptateur
M6 x 20 mm (4)
520-9554
M6 x 30 mm (4)
520-1067
M8 x 15 mm (6)
520-1068
M8 x 40 mm (4)
520-1152
M8 x 25 mm (4)
520-1101
M6 x 20 mm (4)
520-9402
M6 x 30 mm (4)
510-9109 rondelletout usage (6)
580-1036
M8 x 16 mm (6)
520-9257
M8 x 40 mm (4)
520-1136
M4 x 12 mm (6)
504-9013
Fixations Phillips du support adaptateur
M4 x 25 mm (4)
504-1015
M5 x 12 mm (4)
520-1027 M5 x 25 mm (4)
520-9543
M6 x 12 mm (4)
520-1128
M6 x 25 mm (4)
520-1208 M8 x 25 mm (4)
520-1031
I.D. .22" (5.6 mm) (4)
540-1057 I.D. .34" (8.7 mm) (4)
540-1059
I.D. .22" (5.6 mm) (4)
540-1057 I.D. .34" (8.7 mm) (4) 540-1059

20 of 42 ISSUED: 06-05-06 SHEET #: 202-9140-6 11-21-07
1
AVERTISSEMENT
La plaque murale (A) peut être installée à deux montants espacés de 16 po. Repérez le bord des montants à l’aide
d’un localisateur de montants. L’utilisation d’un localisateur de montants « bord à bord » est fortement
recommandée.Après avoirrepéré lesbords, tracezune ligne verticalele longdu centrede chaquemontant. Posez
la plaque murale sur le mur et utilisez-la comme gabarit. Les fentes de montage supérieures doivent être situées à
3,9 po en dessous de l’endroit souhaité pour le centre de l’écran. Mettez la plaque à niveau et marquez le centre des
quatre trous de fixation. Veillez à ce que les trous de fixation soient sur la ligne médiane du montant. Percez six
trous de 3/16 po (5 mm) de dia. et de 3 po (76 mm) de profondeur. Veillez à ce que la plaque murale soit de niveau
et fixez-la à l’aide de six vis à bois de 5/16 x 3 po (O) et des rondelles (P).
Passez à l’étape 2 à la page 22
A
O
P
Installation sur des murs à montants en bois
AVERTISSEMENT
• N’installez jamais ce produit sur des montants
métalliques sans les accessoires requis.
• L’installateurdoit s’assurerque la surfacede support puisse soutenirsans danger la chargetotale de l’équipement
ainsi que des pièces et composants qui y sont attachés.
• Serrez fermement les vis à bois pour que la plaque murale tienne solidement en place, mais sans excès. Un serrage
excessifpeutendommagerlesvisetenréduireconsidérablementlepouvoirdemaintien.
• Ne serrez jamais à plus de 80 po-lb (9 Nm).
•Ne pas monter directement sur un mur à montants métalliques. Il est nécessaire d’utiliser une plaque murale WSP
afin de fixer le support à des montants métalliques (veuillez vous adresser au service à la clientèle).
• Assurez-vous que les vis de montage sont fixées au centre des montants. L’utilisation d’un localisateur de montants
"bordàbord"estfortementrecommandée.
• Lespièces de fixations fourniessont prévuespour une installationdu supportsur desmontants enbois à traversune
cloison sèche ou du plâtre d’épaisseur standard. Il est de la responsabilité de l’installateur de fournir les pièces de
fixationrequises pour tout autretype d’installation.
• Ne dépassez jamais la capacité de charge maximum de 150 lb (68 kg).