PEERLESS DST360 Guide

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessmounts.com
ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Installation and Assembly:
Mount - Wall/Ceiling Mount
Model: DST360
Max Load Capacity: 150 lb (68. kg)

2 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Description Qty. Part #
Apc box 1 145-1050
Baccess plate 1 145-1049
Cadapter plate 1 145-1038
Dpinch bracket 1 130-1073
Eyaw lock bracket 1 140-1019
FM6 x 12 mm socket pin serrated washer head screw 6 510-1050
Galligator anchor 6 590-0097
H#14 x 2.5 hex phillips wood screw 6 5S1-015-C03
I4 mm allen wrench 1 560-9646
Jrubber pad 4 590-1159
K2" snap bushing 1 590-1149
LM8 x 15 mm socket pin screw 4 520-1068
Mretaining collar 1 1800-375
Nwasher 1 540-9432
OM5 x 10 mm type F screw 1 520-9250
PM5 nylock nut 2 530-1019
QM5 x 55 mm socket screw 2 520-1193
R1/4 - 20 x 2.5 phillips screw 6 520-9521
Stoggler 6 560-9708
T1/4 - 20 washer 6 540-9440
UM4 x 12 mm phillips screw 4 504-9013
V
#8 washer 4 540-1001
WM5 x 12 mm phillips screw 4 520-1027
XM6 x 12 mm phillips screw 4 520-1128
PARTS LIST
NOTE: Read instruction sheet before you start installation and assembly.
NOTE: Some parts may appear slightly different than illustrated
nt
B
A
CD
EF G HI
KLM N
OP Q R S
TUVWX
J

3 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Using access plate (B) as a template, drill six 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach
access plate (B) to centers of wood studs using six #14 x 2.5" wood screws (H) shown.
Installation to Wood Stud Wall
• Installermust verify thatthe supporting surfacewill safely supportthe combined loadof the equipmentand all attached
hardwareandcomponents.
• Tightenwood screws sothat wall plateis firmly attached,butdo not overtighten.Overtightening can damagethe
screws,greatlyreducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highlyrecommended.
• Hardwareprovided is forattachmentof mount throughstandard thickness drywall orplaster into woodstuds.Installers
areresponsibleto provide hardware forothertypes of mounting situations.
WARNING
1
H
B
For Intallation to Column skip to Step 10 on Page 9

4 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Position access plate (B) at desired position on wall.Use
access plate (B), making sure that it is level, as a tem-
plate to mark holes. Drill six 1/4" (6 mm) dia. holes to a
minimumdepth of 2-1/2"(64 mm). Concretemust be 2000
psi density minimum. Insert anchors (G) in holes flush
with wall as shown in figure 2.3. Place access plate (B)
over anchors and secure with six #14 x 2-1/2" (6 mm x 65
mm) wood screws (H) as shown in figure 2.4. Make sure
wall plate is level and tighten all fasteners.
Installation to Solid Concrete and Cinder Block Wall
2
CUTAWAYVIEW
INCORRECT
concrete
plaster/
drywall
B
CORRECT
concrete
plaster/
drywall
B
concrete
wall
Drill holes and insert anchors.
Place access plate (B) over anchors and secure with
screws (H).
Tighten all fasteners.
H
B
1
2
• Tighten wood screws firmly,but do notovertighten.
Overtighteningcandamage the screws, greatly
reducingtheirholdingpower.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid
breakingout the backof the holewhen entering avoid or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Makesure thatthe supporting surface will safelysupport thecombined load of the equipmentand allattached hard-
wareandcomponents.
WARNING
G
G
H
G
fig 2.3
fig 2.4
• Concreteanchors are notintendedforattachmentto
concretewall covered withalayer of plaster, drywall,
orotherfinishing material asshownbelow.Ifmounting
toconcrete wall coveredwith plaster/drywall is
unavoidable,plaster/drywall (up to5/8" thick) mustbe
counterboredas shown below.Be sure concrete
anchorsdo not pullawayfrom concrete whentighten-
ing screws. If plaster/drywall is thicker than
5/8", custom fasteners must be supplied by installer.
WARNING
CINDERBLOCK
SOLIDCONCRETE
B
3

5 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Rotatetoggler(S)
clockwise to wedge it
against inside walls
of metal stud.
Push into hole.
Pivotendof toggler (S).
Slide plastic cap
forwardwhilepulling
back firmly on ring.
Break off excess.
FOR METAL STUD WALLS ONLY: Drill six 1/2"
(13 mm) dia. holes through drywall and studs at
locationscorresponding to wallplate.Insert togglers
(S)as shown below.
S
S
∅ 1/2"
(13mm)
• Product must be mounted through drywall that has a
minimum thickness of 1/2" and into metal studs, 26
gaugeorheavier.
• Make sure that togglers are anchored into the center
of the studs as shown in figure 3.1. The use of an
"edgeto edge" studfinder is highlyrecommended.
fig. 3.1
WARNING
3
3-1
3-2
3-3
3-4
3-5

6 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Align wall plate with
holein wall and
fastenusing
1/4-20 x 2.5" screw
(R)and1/4"
washer(T).
access plate
RT
3-6
R
T
S
B
Select mounting hole pattern and secure adapter plate (C) to screen using screws (U,W, or X) and washers
(V)ifrequired.
4200mm x200 mm 200mm x100 mm PLP Adapter Plate Mounting Holes
Fastenersprovidedby
dedicatedadapterplate
Using Screws (U,W, or X) and washers (V) as required
PLPADAPTERPLATE
NOTE: First attach the vertical uprights to the
screen detailed in the PLPAdapter Plate
instructions
verticaluprights

7 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Thread two M6 x 12 mm socket pin screws (F) into
PC box (A) leaving 1/8" exposed thread as shown in
detail 1. Hook screen and adapter plate onto exposed
screws.
7
Secure PC box (A) to access plate (B) with
four M8 x 15 mm socket pin screws (L).
Tightenusing allen wrench(I).
6
A
B
L
Detail 1
A
1/8"
A
F
5SecurePC topc box (A) using strapprovided withpc box (A), and rubber pads (J)for support andventilation. Secure
2" snap bushing (K) as desierd.
J
A
PC
PC
STRAP
K

8 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Loosen top two M8 x 15 mm socket pin screws (L) 1/4 turn and temporaliy remove bottom two M8 x 15 mm socket
pin screws (L) on pc box (A) as shown. Swing screen forward and swing support brackets downward to brace screen
inopen position.
Accessing CPU
9
A
A
SUPPORTBRACKETS
(BOTHSIDES)
LOOSENSCREWS1/4
TURNONBOTHSIDES
Secure two M6 x 12 mm socket pin screws (F)
into PC box (A) at desired tilt. Tighten using allen
wrench(I).
8
A
F
L
REMOVE
L

9 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
SecurePC topc box (A) using strap provided withpc box(A), and rubber pads (J) for support and ventilation.
Secure 2" snap bushing (K) as desierd.
Secure yaw lock bracket (E) to pc box (A) with two
M6 x 12 mm socket pin screws (F). Tighten using
allenwrench(I).
Slide tube into top of pc box (A) and secure using
washer (N), retaining collar (M) and one M5 x 10 mm
type F screw (O).
Secure pc box (A) to tube using two M5 x 55 mm
socket screws (Q), pinch bracket (D), yaw lock
bracket (E), and M5 nylock nut (P).
Installing To Column
12
J
A
PC
PC
STRAP
10 11
F
AE
O
N
M
A
Q
E
P
D
K

10 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Secure pc box (A) to access plate (B) using
four M8 x 15 mm socket pin screws (L).
A
B
L
14
A
Detail 2
Thread two M6 x 12 mm socket pin screws (F) into
pc box (A) leaving 1/8" exposed thread as shown in
detail 2. Hook screen and adapter plate onto exposed
screws.
15
F
A
1/8"
F
13 Select mounting hole pattern and secure adapter plate (C) to screen using screws (U,W, or X) and washers
(V)ifrequired.
200mm x200 mm 200mm x100 mm PLP Adapter Plate Mounting Holes
Fastenersprovidedby
dedicatedadapterplate
Using Screws (U,W, or X) and washers (V) as required
PLPADAPTERPLATE
verticaluprights
NOTE: First attach the vertical uprights to the
screen detailed in the PLPAdapter Plate
instructions

11 of 11 ISSUED: 06-15-09 SHEET #: 145-9008-2 11-17-09
Loosen top two M8 x 15 mm socket pin screws (L) 1/4 turn and temporaliy remove bottom two M8 x 15 mm socket
pin screws (L) on pc box (A) as shown in figure 17.1. Swing screen forward and swing support brackets downward to
brace screen in open position as shown in figure 17.2.
LOOSENSCREWS1/4
TURNONBOTHSIDES
SUPPORTBRACKETS
(BOTHSIDES)
REMOVE
fig. 17.1 fig. 17.2
A
Accessing CPU
17
A
Secure two M6 x 12 mm socket pin screws (F)
into PC box (A) at desired tilt. Tighten using allen
wrench(I).
16
F
L
L