Pegasus HD879X-0004 Assembly instructions

INSTALLATION AND CARE GUIDE
TWO-HANDLE ROMAN TUB FAUCET
11/2016 REV.01HOMEDEPOT.COM
Model#
HD879X-0004
HD879X-0096H
SKU#
767439
767442
THANK YOU
We appreciate the trust and condence you have placed in Pegasus through the purchase of this roman tub
faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you for choosing Pegasus!
Questions, problems, missing parts?
Before returning to the store, call Pegasus Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-877-580-5682
WWW.HOMEDEPOT.COM/PEGASUS

Phillips
screwdriver Basin
wrench
2
Table of Contents
Important Information..............................2
Warranty ...................................................2
Pre-Installation.........................................2
Planning Installation ..............................2
Package Contents..................................3
Installation................................................4
Care and Cleaning ....................................9
Troubleshooting........................................9
Service Parts ........................................... 10
Important Information
□ Observe all local plumbing and building codes.
□ Cover the sink drain to avoid losing any parts.
□ Review the care and cleaning section included in this guide.
Pre-Installation
PLANNING INSTALLATION
Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package
Contents list. If any part is missing or damaged, do not attempt to install the product. Contact customer service
for replacement parts.
TOOLS AND HARDWARE REQUIRED
Adjustable
wrench
Safety
goggles
(2) Supply
lines
Tools and Hardware Required ...............2
Operation...................................................9
Warranty
LIMITED LIFETIME WARRANTY
Pegasus products are manufactured with superior quality standards and workmanship and are backed by our
limited lifetime warranty. Pegasus products are warranted to the original consumer purchaser to be free of
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that prove defective.
Simply, return the product / part to any of The Home Depot retail locations or call 1-877-580-5682 to receive the
replacement item. Proof of purchase (original sales receipt) from the original consumer purchaser must be made
available for all Pegasus warranty claims.
This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and
tear. This warranty excludes all industrial, commercial & business usage, whose purchasers are hereby, extended
duration of warranty.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other
rights that vary from state to state and province to province. Please see a store or contact 1-877-580-5682 for
more details.

3
Pre-Installation (continued)
PACKAGE CONTENTS
Part Description Quantity
EIndex 2
FSet screw 2
G 2
HFlange 2
Handle
Part Description Quantity
ASpout assembly 1
BRubber washer 1
CMetal washer 1
DMounting nut 1 T Metal washer 1
UMounting nut 1
V 1
WRubber washer 1
Spray support
PDiverter handle 1
QFlange 1
RDiverter body 1
SRubber washer 1
LMetal washer 2
MMounting nut 2
N 1
OSet screw 1
Index
IHot end valve 1
JCold end valve 1
KRubber washer 2 AA Hex wrench 1
BB Hose 1
CC 1
DD Hose 2
EE Flange 1
Hose
XMetal washer 1
YMounting nut 1
ZSpray assembly 1
BB
CC
DD
A
B
C
D
G
F
E
H
J
K
L
M
I
N
O
P
Q
R
S
T
UV
W
X
Y
Z
AA
EE
WWW.HOMEDEPOT.COM/PEGASUS
Please contact 1-877-580-5682 for further assistance.

4
Installation
1 Preparing for installation
CAUTION: Always turn off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
□Shut off the water supply. Remove the old
faucet.
□Clean the mounting surface.
□Drill holes in the nished deck as shown in
the diagram below.
5 in. min.
8~16 in.
4~6 in. 4~6 in.
3 in. min.
1-3/4 in. MAX. DECK THICKNESS
1-1/8 in.
Diamter
1-3/8 in.
Diamter
1-3/8 in.
Diamter
1-3/8 in.
Diamter
1-3/8 in.
Diamter
NOTE: This kit allows up to 1-3/4 in. deck thickness.
2 Installing the spout assembly
□Remove the preassembled mounting nut (D) and
washers (B & C) from the spout assembly (A).
□Insert the spout assembly (A) through the hole
in the deck.
□Before installation, ensure that the ange (EE) is
placed on the bottom of the spout assembly (A).
□Secure the spout assembly (A) with the rubber
washer (B), metal washer (C) and mounting
nut (D).
3 Removing the mounting kits
□Remove the indexes (E). Loosen the set screws
(F) with the Hex wrench (Hex: 2.5mm, AA) and
remove the handles (G).
□Loosen the anges (H) from the valve bodys
(I & J). Adjust the rubber washers (K), metal
washers (L) and mounting nuts (M) to the
bottom of valve bodys (I & J).
B
C
D
A
EE
I
K
L
M
H
J
K
L
M
H
G
FE
G
F
E
AA

5
Installation (continued)
4 Installing the valve bodies
□From underneath the deck, insert the cold end
valve (J) with the rubber washer (K), metal
washer (L) and mounting nut (M) through
the hole on the right (cold) side.
□From above, thread the ange (H) onto the
valve body (J).
□Tighten the mounting nut (M) using a basin
wrench, so that the ange (H) sits ush against
the nished deck surface.
□Repeat this procedure for the hot end valve (I)
on the left (hot) side.
NOTE: The hot end valve is identied with a label.
5 Installing the handle
□Place the handle (G) onto the inverter (1). Place
the set screw (F) into handle (G) and tighten set
screw (F) with the Hex wrench (Hex: 2.5mm, AA).
Insert the index (E).
□Place the other handle onto the left (hot) valve
and install the same way.
H
K
L
M
J
I
G
F
EAA
1
WWW.HOMEDEPOT.COM/PEGASUS
Please contact 1-877-580-5682 for further assistance.

7 Installing the diverter valve
body
□From underneath the deck, insert the diverter
valve body (R) with the rubber washer (S),
metal washer (T) and mounting nut (U) through
the hole.
□From above, thread the ange (Q) onto the
diverter valve body (R).
□Tighten the mounting nut (U) using a basin
wrench, so that the ange (Q) sits ush against
the nished deck surface.
6 Removing the mounting kits
□Remove the index (N). Loosen the set screw (O)
with the Hex wrench (Hex: 2.5mm, AA) and
remove the diverter handle (P).
□Loosen the ange (Q) from the diverter valve
body (R). Adjust the rubber washer (S), metal
washer (T) and mounting nut (U) to the bottom
of diverter valve body (R).
6
Installation (continued)
NOTE: Make sure that the face marked with "FRONT" on
the diverter valve body (R) is facing forward.
R
S
T
U
Q
N
O
P
AA
Q
R
S
T
U

8 Installing the diverter handle
□Before installation, place the diverter handle (P)
onto the inverter (1) and turn it clockwise until
it stops, then remove the diverter handle (P).
□Reinstall the diverter handle (P) facing forward
onto the inverter (1) and tighten set screw (O)
with the Hex wrench (Hex: 2.5mm, AA). Insert
the index (N).
7
Installation (continued)
9 Installing the spray support
□Remove the preassembled mounting nut (Y) and
washers (W & X) from the spray support (V).
□Insert the spray support (V) through the hole in
the deck.
□Secure the spray support (V) with the rubber
washer (W), metal washer (X) and mounting
nut (Y).
10 Installing the spray
assembly
□Insert the spray assembly (Z) into
the spray support (V).
N
OAA
P
1
V
W
X
Y
Z
V
WWW.HOMEDEPOT.COM/PEGASUS
Please contact 1-877-580-5682 for further assistance.

1
2
11 Connecting the hoses
□Connect one end of hoses (DD) to the two connectors on the diverter valve body (R) and the other end
of the hoses (DD) to the bottom of the hot and cold end valves (I & J).
□Connect one end of hose (CC) to the diverter valve body (R) and the other end of the hose (CC) to the
shank on spout assembly (A).
□Connect one end of hose (BB) to the diverter valve body (R) and the other end of the hose (BB) to the
spray assembly (Z).
□Gently bend the hoses to available space underneath the deck. Tighten all connections with a wrench.
8
Installation (continued)
12 Making the water supply
connections
□Connect the water supply lines (1) to the
faucet inlets (2). (Supply lines are not
included.)
BB
CC
DD
DD
R
I
J
A
Z

9
Care and Cleaning
□To clean, wipe down with a damp cloth and dry with a towel.
□Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will
be voided.
Troubleshooting
Problem Possible Cause Solution
There are leaks from the
handle.
The bonnet nut has come loose and/or the
washer is dirty or damaged.
□Tighten the bonnet nut.
□Clean or replace the washer.
The water will not shut off
completely.
The cartridge is dirty or broken. □Remove the handle to check
the cartridge.
□Clean or replace.
NOTE: Refer to the service parts section in this manual for
a detailed drawing showing the location of the parts listed
below.
1 Flushing and checking for leaks
□Ensure the faucet handles are in the off position,
and turn on the water supply and check for leaks.
If you discover any leaks, check your connections
to ensure they are installed properly.
□Turn on the hot and cold handles to allow the
water to run for at least one minute. This
ushes away any debris that could cause
damage to internal parts.
□Rotate the diverter handle (P) 180°
counter-clockwise to make the diverter
handle (P) is facing backward, and allow
both hot and cold water to run for at least
one minute each from the spray assembly (Z).
This ushes away any debris that could cause
damage to internal parts.
□While the water is running, check for leaks.
□Turn off the water.
Operation
Z
A
P
WWW.HOMEDEPOT.COM/PEGASUS
Please contact 1-877-580-5682 for further assistance.

10
Service Parts
*Specify Finish
Faucet ID tags
can be found
by removing
the hot water
handle
17 Inverter RP64042
Part Description Part Number Part Description Part Number
1
2
3
4
Rubber washer RP64032
5
Metal washer RP64033 15
Index RP10007*
6
14
Mounting nut RP56028 16
Set screw RP50002
Handle RP13040*
Metal washer RP64024
Mounting nut RP56014
Connector RP50022
7
8
9
10
Flange RP80039*
11
Connector RP50019
12
Inverter RP64044
Cartridge H RP20067
Bonnet nut RP70001
Cartridge C RP20068
13 Rubber washer RP64023
Diverter RP70235
19
20
Connector RP70064
18 Bonnet nut RP70043
24 Hose RP70046
22 Mounting nut RP56016
21 Metal washer RP64147
23 Spray assembly RP38336*
26 Hose RP70042
25 Hose RP70063
Many replacement cartridges, aerators, and drain
assemblies can be purchased at your local The
Home Depot store or online at HOMEDEPOT.COM
1
2
3
45
6
7
9
10
8
11
12
13
14
15
16
17
18
19
4
5
6
7
20
21
22
13
14
15
13
23
24
25
26