pellenc AIRION 2 User manual

pellenc s.a.
Route de Cavaillon
B.P. 47
84122 PERTUIS cedex
(France)
Tel : [phone] Fax : [phone]
E-mail : [email protected]
www.pellenc.com
AIRION 2
57_122866_C - 01/2016
USER GUIDE
ENG
Translation of the
original user guide
Blower
READ THE USER’S GUIDE CAREFULLY BEFORE USE
Contents:
- a blower
- a blowing nozzle
- a carrying hook
- an Allen wrench
- a user guide
- hanging hook (x2)
- carrying strap
- at nozzle accessory

3
Table of contents
SAFETY INSTRUCTIONS ......................................................................5
GENERAL SAFETY INSTRUCTIONS FOR THE TOOL ........................................................ 5
SAFETY INSTRUCTIONS FOR AIRION .................................................................... 6
SAFETY INDICATIONS ................................................................................. 7
DESCRIPTION AND TECHNICAL CHARACTERISTICS ..............................................8
TECHNICAL CHARACTERISTICS......................................................................... 9
PUTTING THE TOOL INTO SERVICE ............................................................10
ASSEMBLY / DISASSEMBLY OF THE BLOWING NOZZLE .................................................... 10
ADDING/REMOVING THE NOZZLE PLATE ................................................................ 10
START-UP AND OPERATION ..................................................................11
HOLDING THE TOOL.................................................................................. 11
PREPARING THE BATTERY FOR USE.................................................................... 11
STARTING .......................................................................................... 11
SPEED SELECTOR ................................................................................... 12
"BOOSTER" MODE ................................................................................... 12
CARRYING .......................................................................................... 13
AFTER USE ......................................................................................... 13
SERVICING.................................................................................14
CLEANING .......................................................................................... 14
SERVICING INTERVALS ............................................................................... 14
INSTRUCTIONS FOR REPAIRING ....................................................................... 14
PART NUMBERS FOR SPARE PARTS .................................................................... 15
STORAGE .......................................................................................... 15
INCIDENTS .................................................................................16
«PELLENC S.A.» TERMS OF WARRANTY AND NON-RESPONSIBILITY CLAUSE .......................18
"EC" DECLARATION OF CONFORMITY .........................................................19

4
All through this user guide you will nd advisory notes and information entitled: REMARK, CAUTION /
WARNING.
A REMARK provides additional information, claries a point or explains a step to be followed in detail.
The CAUTION and WARNING advisories are used to dene a procedure which, if neglected or incorrectly
performed, may lead to serious damage to the equipment and/or personal injury.
This advisory:
G
indicates that if the procedures or instructions are not complied with, any damage will not
be covered by the warranty and the owner will be responsible for the repair costs.
Safety indications are also given on the tool; they remind you of the safety precautions to be taken. Identify
and read these indications before using the tool. Immediately replace any indications that may become
partially illegible or deteriorated.
Refer to the «SAFETY INDICATIONS» heading in order to identify the location of the safety
indications on the tool.
No part of this manual may be reproduced without the written consent of PELLENC. The illustrations
given in this manual are for information purposes and are in no way contractual. PELLENC reserves the
right to make any modication or improvement to its products as deemed necessary without informing
customers already in possession of a similar model. This manual forms an integral part of the tool and must
accompany the tool if it changes hands.
It is IMPERATIVE that you read through the ENTIRE USER'S MANUAL before using or servicing the tool.
Always comply with the instructions and illustrations in the manual.
ENVIRONMENTAL PROTECTION
Your equipment comprises numerous materials which can be valorised or recycled. Entrust
these to your reseller or to an approved service centre so that they can be processed.
Comply with the regulations in force in your country as concerns environmental protection
associated with your activity.
INTRODUCTION
PLEASE KEEP THESE INSTRUCTIONS
This manual contains important information and operating instructions for the following tool:
AIRION.

5
SAFETY INSTRUCTIONS
GENERAL SAFETY INSTRUCTIONS FOR THE TOOL
CAUTION Read all the safety measures and all the instructions.
Retain all the safety measures and instructions for later reading.
WORK AREA SAFETY
a. Keep the work area clean and well lit.
b. Do not use electric tools in an explosive atmosphere, for example in the presence of ammable
liquids, gases or dust.
c. Keep children and persons present away when using the tool.
ELECTRICAL SAFETY
a. The plugs of the electric tool must be adapted to the base. Never modify the plug in any way
whatsoever. Do not use adaptors with grounded tools.
b. Avoid any body contact with grounded surfaces such as pipes, radiators, cookers and refrigerators.
c. Do not misuse the power cord. Never use the power cord to carry, pull or disconnect the tool. Keep
the power lead away from heat, lubricant, sharp edges or moving parts.
d. When using a tool outdoors, use an extension adapted to outdoor use.
e. If you must use a tool in a damp place, use power supply protected by a residual current device
(RCD).
PERSONAL SAFETY
a. Remain vigilant, watch what you are doing and use common sense when using the tool. Do not use a
tool if you are tired or under the inuence of drugs, alcohol or medication.
b. Wear safety equipment. Always wear eye protection.
c. Avoid any untimely starting of the device. Make sure the switch is in the off position before connecting
the tool to the mains and/or battery pack, picking it up or carrying it.
d. Remove any adjustment key before starting the tool.
e. Do not rush. Adopt a suitable position and remain balanced at all times.
f. Wear appropriate clothing. Do not wear loose clothing or jewellery.
g. Keep hair, clothing and gloves away from moving parts.
h. If systems are provided to connect dust extraction and recovery equipment, make sure these
systems are connected and properly used.
TOOL USAGE AND MAINTENANCE
a. Do not force the tool. Use a tool suited to your application.
b. Do not use the tool if the switch does not allow it to be switched on and off.
c. Disconnect the plug of the power supply source and/or battery pack from the tool prior to any
adjustment, change of accessories or before putting the tool away.
d. When not in use, keep tools out of reach of children, and do not allow persons to use the tool if they
do not know how to use it and if they have not read these instructions.
e. Comply with tool servicing instructions. Check that the moving parts are not misaligned or jammed,
that there are no broken parts or that there is no other condition which could affect the operation of
the tool. In the event of damage, have the tool repaired before using it.
f. Use the tool, accessories, etc. in accordance with these instructions, taking into account the working
conditions and the work to be done.
MAINTENANCE AND UPKEEP
a. Have the tool serviced by a qualied repairer using only identical spare parts.

6
1– Do not misuse the power lead. Never use the power lead to carry, pull or disconnect the tool. Keep the
power lead away from heat, lubricant, sharp edges and moving parts.
2– Never modify the connector in any way whatsoever.
3– Wear safety equipment. Always wear eye protection.
4– The dust raised during operation can be harmful to health. In case of liberation of dust, wear a dust
mask.
5– Comply with the tool servicing instructions. Check that the moving parts are not misaligned or jammed,
that there are no broken parts or that there is no other condition which could affect the operation of the tool.
If there is damage, have the tool repaired before using it.
6– Inspect the work area prior to starting. Remove all debris and hard object such as stones, glass, wires,
etc. which could y and cause serious injuries or damage when the blower is in use.
7– Use the blower to blow out grass, straw or leaf waste, urban garbage.
8– Never blow towards people or animals - the blower can lift up small objects and throw them out at high
speed - risk of injury.
9– While using the blower, be careful not to endanger small animals.
10– Stop the blower, turn off the battery, disconnect the power cord and wait for the rotor to stop before
opening the air intake grille: risk of serious injuries (moving part).
11– Do not obstruct, part or all of the air intake.
12– Ensure air intake grille maintenance.
13– Inspect the blower before each use, check that the parts are not worn, loose, damaged or missing. Do
not use the blower if it is not in perfect condition.
14– To avoid re spreading, do not use the blower near wood res or barbecues, etc.
15– Do not draw up solids or liquids through the intake duct - risk of damaging rotating components and
intake grille.
SAFETY INSTRUCTIONS FOR AIRION

7
57_11_010A
1
2
6
3
4
5
SAFETY INDICATIONS
1– LwA sound power level guaranteed.
2– Read the user guide.
3– It is mandatory to wear safety goggles.
4– Nobody must stand within 5 m (16 ft) of the tool in operation.
5– Never put your ngers or insert objects in the air intake grille. When air intake grilles are not mounted, there is a
risk of impact with rotating parts - risk of injuries ! - risk of damaging rotating components.When the air intake grille is
not mounted, there is a risk of impact with rotating parts - risk of injuries ! - risk of damaging rotating components.
Protective equipment Wearing is
1 Visor Optional
2Gloves Recommended
3Non-slip safety boots Optional
4Ear protection Recommended
5Safety goggles Mandatory
6Protective trousers Recommended
The IP54 protection concerns only the tool, not the battery. This means that it is protected against dust
and against water spray from all directions.

8
DESCRIPTION AND TECHNICAL CHARACTERISTICS
1– Control handle
2– Speed selection button / "Booster" mode
3– Power and speed indicator lights
4– Gradual control trigger
5– Protective casing
6– Blower power cord
7– Air intake elbow (Pellenc innovation)
8– Air intake grille (Pellenc innovation)
9– Electronic maintenance hatch
10– Axial-ow turbine (Pellenc innovation)
11– Blast nozzle
12– Carry hook (see page 13 )
13– Allen wrench
14– Hanging hook (x2)
15– Carrying strap
16– Flat nozzle accessory

9
TECHNICAL CHARACTERISTICS
WARNING
Blowers manufactured prior to July 2013 are not compatible with ULIB batteries with grey connectors.
Sound emission
Maximum A-weighted sound pressure level (ref. 20 µPa) at the position of the
user LpA = 79 dB(A) K = 2,5 dB(A)
C-weighted peak sound pressure (ref. 20 µPa) at the position of the user LpC < 130 dB(C)
Symbol Value Unit Reference Comment
LWAm 90 dB(A) 1 pW Measured sound power level
LWAg 92 dB(A) 1 pW Guaranteed sound power level
The recording of the measured sound power level and of the guaranteed sound power level has been performed
according to a procedure in accordance with directive 2000/14/CE appendix V.
Vibration rate
Vibration emission value as per EN 60745-1:2010 handle
ah ≤ 0,7 m/s²
uncertainty
Kd = 1,5 m/s²
Determining the sound levels and vibration rates is based on the operating conditions at the maximum nominal rating.
AIRION 2
Effective thrust* (N) 17.5 (boost)/13.5 (speed 4)
Max. power (W) 940
Weight of the tool with cable (kg) 2.8
Weight of the tool without the cable (kg) 2.450
Actual weight of the tool in use (kg) 2.550
Dimensions (l x w x h) (mm) 1022 x 232 x 318
Actual airow rate with nozzle* (m3/h) 920 (boost)/815 (speed 4)
Maximum airow speed with nozzle (m/s) 63
Maximum airow speed with nozzle plate (m/s) 69
Noise level (LpA)** (dB(A)) 79
Guaranteed sound level (Lwa)** (dB(A)) 92
Sound pressure at 15 meters* (dB (A)) < 65
Vibration level*** (m/s²) <2.5 (0.5 actual)
Battery life**** with ULiB 1100, Up to 5 hours
* Values determined according to ANSI/OPEI B175.2-2012
** Values determined according to the acoustic measurement standards NF EN ISO 11203, NF EN ISO 3744 and
NF EN ISO 4871.
*** Vibration emission value following DIN EN 60745-1:2009 - Kd uncertainty = 1.5 m/s²
**** For information: the times were observed in actual working time, without taking breaks into consideration. Battery
life is inuenced by the nature of the work carried out.

10
PUTTING THE TOOL INTO SERVICE
ASSEMBLY / DISASSEMBLY OF THE BLOWING NOZZLE
WARNING
Never operate the blower with the nozzle not fully
assembled and locked.
ASSEMBLY
1– Fit the blowing tube (1) in nozzle (2) up to the locking stud
(3).
2– Make a quarter turn in the direction shown (4) to lock the
nozzle.
DISASSEMBLY
1– Make a quarter turn in the direction shown (1) to unlock the
nozzle.
2– Disconnect the blowing tube from the nozzle (2).
ADDING/REMOVING THE NOZZLE PLATE
ADDING
1– Push the nozzle plate (1) onto the end of the blow nozzle (2)
to the stud (3).
2– Make a quarter turn in the direction shown (4) to lock the
nozzle plate.
REMOVING
1– Make a quarter turn in the direction shown (1) to unlock the
nozzle plate.
2– Detach the nozzle plate from the blower nozzle (2).

11
HOLDING THE TOOL
The blower is designed to be operated with one hand.
The user can carry it holding the control handle with the left or right hand.
Always walk slowly while working.
Always check the blowing nozzle outlet area.
STARTING
PREPARING THE BATTERY FOR USE
Refer to the notice for the Pellenc tools battery.
Before start-up, make sure that the blower is in perfect condition to guarantee safe operation.
The progressiveness of the control trigger allows precise and instantaneous control of the air ow.
CAUTION
Make sure you keep sufcient distance (at least 30 cm) between the air intake and any volatile source
(grounds, walls, roofs, etc.), such as sand, gravels, liquids, etc.
These objects are likely to be drawn, pass through the air intake grille, damage your equipment and
be high-speed projected.
1– Connect the blower power cord to the Pellenc power tool
battery. Screw it on and make sure it is properly attached.
2– Hold the blower in its operating position, blowing nozzle
pointing to the ground.
3– Switch the on/off switch of the Pellenc tool battery to on "I".
The battery will beep 3 times, the tool is recognised.
4– The LEDs on the handle light up in sequence for one to three
seconds.
5– As soon as one or more LEDs no longer blinks, the battery is
recognized and the tool is ready to work.
6– Press the control trigger (1) to start the blower. Walk slowly
while blowing out from one side to another the leaves, green
waste or urban garbage.
7– The blower speed varies according to the pressure on the
trigger.
8– Release the trigger (1) to stop the blower.
START-UP AND OPERATION

12
Only use the "booster" mode temporarily and in case you need it (stuck debris, etc.) in order to limit the
blower power consumption.
"BOOSTER" MODE
SPEED SELECTOR
Your blower is equipped with a speed change system. This
system is used to optimize and vary the air ow power using the
selector (1) on the handle.
When the blower is energized, the four indicator lights on the
handle (2) indicate the selected speed.
TOOL + STANDARD NOZZLE
Selected speed Speed 1 Speed 2 Speed 3 Speed 4 Boost
Indicator light status
Power (W) 150 380 500 600 940
Battery life (min) * 395 160 120 100 63
Max. airow speed (m/s) ** 33 47 52 55 63
Max. airow speed with accessories (m/s) *** 37 52 57 60 69
Actual ow rate (m3/h) ** 490 690 760 815 920
Effective thrust (N) ** 5 10 12 13,5 18
* With an 1100 battery
** With a standard nozzle
*** With a nozzle plate attachment
The blower has a "booster" mode which gives the maximum
power (940W) instantly. The airow speed and rate is then at a
maximum with the standard nozzle.
This mode is available for each speed.
Hold the selector button down (1) to switch to the "booster"
mode. The mode is activated instantly, 4 LEDs ash
simultaneously.
Release the button, the tool stays in "booster" mode.
A second press causes it to return to the initial speed.

13
57_11_008B
AFTER USE
Attach the blower to the carrying hook.
1– Flip the ON/OFF switch of the Pellenc power tool battery to
OFF «0»
2– Unscrew the blower power cord and remove the battery.
3– Make 3 loops with the cord and attach it at the rear of the
handle with the carrying hook (see picture).
Install the carrying hook on the lateral strap of the equipment
carrier vest.
CARRYING

14
56_10_016A
G
G
SERVICING
CLEANING
WARNING:
Before working on the tool, check that the On / Off switch is in the off position
«0» and disconnect the battery power lead.
Keep your blower clean by wiping it regularly with a soft moist cloth.
Using an air compressor, (10 bars), blow the tool, the grille and the propeller on a regular basis to limit fouling.
Check that the whole air duct (from the intake to the outlet) is not obstructed.
Ensure that air intake grille holes are not obstructed.
Replace the inlet screen in case of damage, even if it is partial.
Check the condition of the rotor. If a replacement is necessary contact your PELLENC distributor.
CAUTION:
Never use solvents (Trichlorethylene, White Spirit, gasoline, etc) to clean the tool.
SERVICING INTERVALS
Each time the tool is used
After use
Each year or when necessary
Clean the tool X
Visually inspect the tool X
Check for clogging of the grid; clean if necessary X X
Check the rotor:
• clean if necessary
• replace if necessary (by an authorised PELLENC distributor)
X
Check the battery charge level X
Safety label replacement X
Send the tool to an approved dealer for inspection X
REMARK:
Have your blower overhauled every 400 hours or at least once a year.
When the tool is stored, it must be clean and the battery must be charged.
INSTRUCTIONS FOR REPAIRING
CAUTION!
G
Only perform the maintenance and servicing interventions described in this manual.
More important repairs can only be carried out by an approved Pellenc dealer.

15
PART NUMBERS FOR SPARE PARTS
127757
Air intake grille
- Always make sure the tool is clean and its battery is charged before storing it.
- Store the tool away from humidity and dust.
- Store the tool in a safe place, out of reach of children and unauthorized persons.
STORAGE

16
INCIDENTS
Repaired by
User
PELLENC approved
dealer
User
PELLENC approved
dealer
PELLENC approved
dealer
PELLENC approved
dealer
User
PELLENC
authorised
distributor
PELLENC
authorised
distributor
Solutions
Switch on the battery switch
Change the cord
Recharge the battery
Change the electronic
board if the LEDs remain
off after commissioning and
verication of the previous
points
Change the trigger or sensor
Change the electronics board
Repeat the starting
procedure.
Change the cord
Change the electronic board
Checks
Battery switch
Check the cord’s condition
Check that the battery is not
completey discharged
At PELLENC approved
dealer premises
At PELLENC approved
dealer premises
At PELLENC approved
dealer premises
Check the connection of the
cord to the battery,
Check the condition of the
cord
At an authorised PELLENC
distributor
Probable cause
Battery off
The power cord is sectioned
Battery
Electronic board
A trigger no longer functions
Electronic board
Battery not recognized
Faulty power cord
Electronic board defect
Indicator light
status
Out Out
On
Flashing then
off
Battery start/stop
switch position
0
I
Symptoms
The tool does not
start

17
INCIDENTS
Repaired by
PELLENC approved
dealer
PELLENC approved
dealer
User User User User User User
PELLENC approved
dealer
User
Solutions
Change the trigger or
sensor
Change the cord
Allow tool to cool for
approximately 5 minutes
Recharge the battery (if less
than 10%)
Clean the duct
Clean or replace the rotor
Clean or replace the grille
Clean the rotor
Replace the rotor
Clean the grill
Allow the tool to cool down
Checks
At PELLENC approved dealer
premises
Check the condition of the
cord
4 beeps on the battery
When stopped, check the
battery charge level indicated
on the side display
Check the condition of the duct
Check the condition of the
rotor
Check the condition of the
grille
Check the condition of the
rotor
Check the condition of the
grille
Probable cause
A trigger no longer functions
The power cord is sectioned
The tool has reached its temperature
limit
The battery is discharged
Air ow duct obstructed or blocked (air
intake elbow, blowing tube, nozzle, etc.)
Dirty or damaged rotor
Blocked air intake grille
Dirty or damaged rotor
The tool is hot
Cooling mode in operation
Indicator light
status
On
Out
On On On
and
convergent
Condition of battery
start/stop switch
I I I I
Symptoms
The tool stops
during use
The blower makes
an unusual noise or
vibrates abnormally
Loss of efciency of
the air ow
The tool works, the
boost is temporarily
unavailable

18
«PELLENC S.A.» TERMS OF WARRANTY AND NON-RESPONSIBILITY CLAUSE
Warranty against latent defects
Apart from the commercial warranty foreseen under Article XX, Article 1641 of the Civil Code provides that "the seller is bound to a warranty on account of latent defects of the object sold which
render it unt for the use for which it was intended, or which would impair said use to the extent that the buyer would not have acquired it, or would only have given a lesser price for it, had he
known of them".
Article 1648 of the Civil Code "The action resulting from latent defects must be brought by the purchaser within two years after the discovery of the defect. "
Legal warranty of conformity
Article L.211-4 of the Consumer Code "The seller must deliver goods in conformity with the contract and is liable for defects of conformity existing upon delivery. The seller is also liable for any lack
of compliance resulting from the packaging, assembly or installation instructions, when these have been made its responsibility under the contract or have been produced under its responsibility
Article L.211-5 of the Consumer Code "To comply with the contract, the product must: 1) Be suitable for the purpose usually expected of similar goods and, where applicable: - Match the description
given by the seller and possess the qualities that it has presented to the buyer as a sample or model; - The features that a buyer might reasonably expect given the public statements made by the
seller, the producer or his representative, particularly in advertising or labelling; 2) or have the characteristics dened by mutual agreement by the parties or be suitable for any particular purpose for
which the buyer made known to the seller and the latter accepted. "
Article L.211-12 of the Consumer Code "legal action resulting from lack of conformity lapses two years after delivery of the goods".
Commercial Warranty
General Information
In addition to legal warranties, client users benet from the commercial warranty on PELLENC products covering the exchange and replacement of parts recognised out of use, caused by
machining defects, assembly defects or material defects, whatever the cause.
The warranty forms an inseparable whole with the product sold by PELLENC.
Spare Parts
The commercial warranty also covers original PELLENC spare parts, excluding labour and to the exclusion of certain parts that fall within specic extended commercial warranties dened in the
manual of each product provided at delivery.
Duration of the warranty
General Information
PELLENC products are guaranteed under the commercial warranty as from delivery to the customer for a period of two (2) years for products connected to a PELLENC battery, and for a period of
one (1) year for other PELLENC products.
Spare Parts
PELLENC spare parts replaced under the product warranty are guaranteed under the commercial warranty as from delivery of he PELLENC product to the customer for a period of two (2) years for
products connected to a PELLENC battery, and for a period of one (1) year for other PELLENC products.
In the case of products connected to a Pellenc battery, parts that are replaced in the under the product warranty after the 12th month of use, are covered for a period of one (1) year.
Warranty exclusions
Excluded from the commercial warranty are products that have been subject to abnormal use, or were used under conditions and for purposes other than those for which they were manufactured,
especially in the case of non-compliance with conditions stipulated in the user manual.
It does not apply in case of shock, fall, neglect, lack of supervision or maintenance or in case of transformation of the product. Also excluded from the warranty are products that have been subject
to tampering, alteration or modication by the client user.
Wear parts and/or consumables cannot be covered by the warranty.
Implementation of the commercial warranty
Product commissioning and commissioning declaration
The DISTRIBUTOR undertakes to complete the computer commissioning declaration form, no later than eight days after the delivery of the property to the user customer, in order to activate the
latter on the www.pellenc.com website under "warranties and training" in the "extranet" menu, using the identier previously provided to them by PELLENC.
Failing that, commissioning declaration will not be effective and implementation of the PELLENC commercial warranty will not occur. As a consequence thereof, the DISTRIBUTOR must ensure the
nancial burden of its intervention under the warranty without being able to pass on the cost to the client user.
The DISTRIBUTOR shall also undertake to complete the warranty card or the certicate of warranty and commissioning for self-propelled equipment provided with the product after having the
client user sign and date it.
For the commissioning declaration to be effective, the DISTRIBUTOR undertakes to attach the warranty card present in each tool package or the warranty and commissioning certicate for self-
propelled equipment, duly dated and signed by the client user, to the commissioning declaration to be made on the www.pellenc.com website.
Paid after-sales service
General Information
Malfunctions, breakdowns, breakages resulting from misuse, neglect or improper maintenance by the client user as well as malfunctions resulting from normal wear of the product are subject
to the payment of after-sales service, even during the period of the legal and commercial warranty. After-sales service repairs that fall outside of the legal and commercial warranty also include
maintenance, adjustments, diagnostics of all types, and cleaning without the present list being exhaustive.
Wear parts and consumables
Wear parts and consumables also fall within the after-sales service.
Spare Parts
Paid after-sales service also covers original PELLENC spare parts, excluding labour and outside the legal and commercial warranty period.
In case of replacement of original PELLENC spare parts in the context of after-sales service, said latter are covered by a warranty of one year as from the installation date.
Quality commitments
The DISTRIBUTOR undertakes to comply with the following quality commitments:
Inform the client user in writing of the cost of delivery at the time of purchase of the tool, if the product must to be delivered.
Inform the client user in writing of the cost of commissioning, at the time of purchase of the tool, if the commissioning service must be paid for
Inform the client user in writing of the cost of user training on self-propelled harvesting machines, at the time of purchase of the tool, if the service must be paid for
Inform the client user of the precautions to be taken, safety instructions and risks related to the use of PELLENC products, as listed in each user manual and more generally provide information,
advice and warnings related to the use PELLENC products.
Give the user manuals to the client user at the time of delivery of the goods or during the scheduled commissioning.
Present the features of the tool during commissioning.
List the personal protective equipment (PPE) required when using the product concerned at the time of commissioning.

19
Symbol Value Unit Reference Comment
LWAm 90 dB(A) 1 pW Measured sound power level
LWAg 92 dB(A) 1 pW Guaranteed sound power level
The recording of the measured sound power level and of the guaranteed sound power level has been performed according to a
procedure in accordance with directive 2000/14/CE appendix V.
MACHINES DIRECTIVE 2006/42/CE, APPENDIX IIA.
(ONLY CONCERNS EUROPE)
MANUFACTURER PELLENC S.A.
ADDRESS QUARTIER NOTRE-DAME
ROUTE DE CAVAILLON - B.P. 47
84122 PERTUIS CEDEX (FRANCE)
PERSON/ENTITY AUTHORISED TO COMPILE THE TECHNICAL DOSSIER PELLENC S.A.
ADDRESS QUARTIER NOTRE-DAME
ROUTE DE CAVAILLON - B.P. 47
84122 PERTUIS CEDEX (FRANCE)
"EC" DECLARATION OF CONFORMITY
WE HEREBY DECLARE THAT, FOR THE MACHINE HEREINAFTER REFERRED TO AS:
GENERIC DENOMINATION HAND-HELD BLOWER
FUNCTION MAINTENANCE WORK IN GREEN SPACES AND ON PUBLIC ROADS
COMMERCIAL NAME AIRION 2
TYPE AIRION 2
MODEL AIRION 2
SERIAL No. 57Q00001 - 57Q49999
COMPLIES WITH THE PERTINENT PROVISIONS OF THE MACHINES DIRECTIVE (2006/42/CE)
AND COMPLIES WITH THE PROVISIONS OF THE FOLLOWING OTHER EUROPEAN DIRECTIVES:
- 2004/108/CE
- 2000/14/CE
- 2011/65/CE (RoHS)
- 2012/19/CE (DEEE)
Sound Level at the maximum operating rating
CONCLUDED AT PERTUIS, DATED 01/12/2015
ROGER PELLENC
CHIEF EXECUTIVE OFFICER