Penguin Computing R270-B2O Quick start guide

IceBreaker 2912/2924
Technical Guide
Rev. 1.0
PENGUIN
COMPUTING
www.penguincomputing.com | 1-888-PENGUIN (736-4846) | twitter:@PenguinHPC

R270-B2O
R270-C3C
Dual LGA2011 sockets R3 motherboard for Intel® E5-2600 V3 series processors
Service Guide
Rev. 1.0

Copyright
© 2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE
without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classifications
In order to assist in the use of this product, GIGABYTE provides the following types of documentations:
■For detailed product information, carefully read the User's Manual.
For more information, visit our website at:
http://b2b.gigabyte.com
You are a professional?
Get an access to our complete source of sales, marketing & technical materials at:
http://reseller.b2b.gigabyte.com
https://www.facebook.com/gigabyteserver

Preface
Before using this information and the product it supports, please read the following general infor-
mation.
1. This Service Guide provides you with all technical information relating to the BASIC CON-
FIGURATION decided for GIGABYTE’s “global” product offering. To better fit local market-
requirements and enhance product competitiveness, your regional office MAY have decided
toextend the functionality of a machine (e.g. add-on card, modem, or extra memory capabil-
ity).These LOCALIZED FEATURES will NOT be covered in this generic service guide. In
suchcases, please contact your regional offices or the responsible personnel/channel to
provide youwith further technical details.
2. Please note WHEN ORDERING SPARE PARTS, you should check the most up-to-date
informationavailable on your regional web or channel. For whatever reason, if a part num-
ber change is made,it will not be noted in the printed Service Guide. For GIGABYTE-AU-
THORIZED SERVICEPROVIDERS, your GIGABYTE office may have a DIFFERENT part
number code to thosegiven in the FRU list of this printed Service Guide. You MUST use the
list provided by yourregional GIGABYTE office to order FRU parts for repair and service of
customer machines.

- 4 -
Table of Contents
Box Contents 7
Safety, Care and Regulatory Information 8
Chapter 1 Hardware Installation 11
1-1 Installation Precautions 11
1-2 Product Specifications 12
1-3 System Block Diagram 14
Chapter 2 System Hardware Installation 15
2-1 Removing Chassis Cover 16
2-2 Removing and Installing the Fan Duct 17
2-3 Installing the CPU 18
2-4 Installing the Heat Sink 19
2-5 Installing the Memory 20
2-5-1
2-5-2
2-5-3
Four Channel Memory Configuration 20
Installing a Memory 21
DIMM Population Table 22
2-5 Installing the PCI Expansion Card 23
2-6 Installing the Hard Disk Drive 24
2-7 Replacing the FAN Assemblly 25
2-8 Replacing and Installing the Power Supply 26
Chapter 3 System Appearance 27
1Front View 27
2Rear View 28
3-3 Front Panel LED and Buttons 29
3-4 Rear System LAN LEDs 31
3-5 Hard Disk Drive LEDs 32
3-6 Cable Routing 33
Chapter 4 Motherboard Components 35
4-1 MD60-SC1 Motherboard Components 35
4-2 Jumper Setting 38
Chapter 5 BIOS Setup 40
5-1 The Main Menu 42
5-2 Advanced Menu 45

1Memory Topology 81
2 Memory Thermal 82
3Memory Map 83
5-3-5-4 Memory RAS Configuration 84
5-3-6 IIO Configuration 85
5-3-6-1 IOAT Configuration 86
5-3-6-2 Intel VT for Directed I/O (VT-d) 87
5-3-7 PCH Configuration 88
5-3-7-1 PCH Devices 89
5-3-7-2 PCH sSATA Configuration 90
5-3-7-2-1 SATA Mode Options 93
5-3-7-3 PCH SATA Configuration 95
5-3-7-3-1 SATA Mode Options 98
5-3-7-4 USB Configuration 100
5-3-8 Miscellaneous Configuration 101
5-3-9 Server ME Configuration 102
5-3-10 Runtime Error Logging 103
5-3-10-1Whea Setting 104
5-3-10-2Memory Error Enabling 105
5-3-10-3PCI/PCI Error Enabling 106
5-4 Server Management Menu 107
- 5 -
5-2-1 Serial Port Console Redirection 46
5-2-2 PCI Subsystem Settings 50
5-2-2-1 PCI Express Settings 52
5-2-3
5-2-4
5-2-5
5-2-6
5-2-7
5-2-8
5-9
Network Stack 54
CSM Configuration 55
Post Report Configuration 57
Trusted Computing 58
USB Configuration 59
Chipset Configuration 60
SIO Configuration 61
5-2-10 iSCSI Configuration 65
5-3 Intel RC Setup Menu 66
5-3-1 Processor Configuration 67
5-3-1-1 Pre-Socket Configuration 70
5-3-2 Advanced Power Management Configuration 72
5-3-2-1 CPU P State Control 73
5-3-2-2 CPU C State Control 74
5-3-2-3 CPU T State Control 75
5-3-3
5-3-4
5-3-5
Common RefCode Configuration 76
QPI Configuration 77
Memory Configuration 79

- 6 -
5-4-1
5-4-2
5-4-3
System Event Log 109
View FRU Information 110
BMC network configuration 111
5Security Menu 112
5-5-1 Secure Boot menu 113
5-5-1-1 Key Management 114
6 Boot Menu 116
7Save & Exit Menu 118
5-8 BIOS POST Codes 120
9 BIOS POST Beep code 124
5-9-1 PEI Beep Codes 124
5-9-2 DEX Beep Codes 124
10 BIOS Recovery Instruction 125

- 7 -
Box Contents
R270-B2O/R270-C3C System
Driver CD
•The box contents above are for reference only and the actual items shall depend on the product package you obtain.
The box contents are subject to change without notice.
•The motherboard image is for reference only.

- 8 -
Safety, Care and Regulatory Information
Important safety information
Read and follow all instructions marked on the product and in the documentation before you operateyour sys-
tem. Retain all safety and operating instructions for future use.
•The product should be operated only from the type of power source indicated on the rating label.* If your
computer has a voltage selector switch, make sure that the switch is in the proper position foryour area.
The voltage selector switch is set at the factory to the correct voltage.
•The plug-socket combination must be accessible at all times because it serves as the main
disconnect- ing device.
•All product shipped with a three-wire electrical grounding-type plug only fits into a grounding-type
poweroutlet. This is a safety feature. The equipment grounding should be in accordance with local and
nationalelectrical codes. The equipment operates safely when it is used in accordance with its marked
electricalratings and product usage instructions
•Do not use this product near water or a heat source.* Set up the product on a stable work surface or so
as to ensure stability of the system.
•Openings in the case are provided for ventilation. Do not block or cover these openings. Make sure
youprovide adequate space around the system for ventilation when you set up your work area. Never
insertobjects of any kind into the ventilation openings.
•To avoid electrical shock, always unplug all power cables and modem cables from the wall outletsbefore
removing covers.
•Allow the product to cool before removing covers or touching internal components.
Precaution for Product with Laser Devices
Observe the following precautions for laser devices:
•Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than
those specified in the product's documentation.
•Only authorized service technicians should repair laser devices.
Precaution for Product with Modems, Telecommunications, ot Local AreaNetwork Options
Observe the following precautions for laser devices:
•Do not connect or use a modem or telephone during a lightning storm. There may be a risk of
electri- calshock from lightning.
•To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord.
•Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle.
•Disconnect the modem cable before opening a product enclosure, touching or installing internalcompo-
nents, or touching an uninsulated modem cable or jack.
•Do not use a telephone line to report a gas leak while you are in the vicinity of the leak.

Federal Communications Commission (FCC) Statement
Warning
This is a class A product. In a domestic environment this product may cause radiointerfer-
enceIn which case the user may be required to take adequate measures.
This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interfer-
ence when the equipment is operated in a commercial environment. This equipmentgenerates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance withthe instruction manual, may
cause harmful interference to radio communications. Operation of thisequipment in a residential area is likely
to cause harmful interference in which case the user will berequired to correct the interference at his own ex-
pense.Properly shielded and grounded cables and connectors must be used in order to meet FCC emission-
limits. Neither the provider nor the manufacturer are responsible for any radio or television interferencecaused
by using other than recommended cables and connectors or by unauthorized changes ormodifications to this
equipment. Unauthorized changes or modifications could void the user's authority tooperate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may cause undesired opera-
tion.
Canadian Department of Communications Compliance Statement
This digital apparatus does not exceed the Class A limits for radio noise emissions from digitalapparatus as
set out in the radio interference regulations of Industry Canada.Le present appareil numerique n'emet pas
de bruits radioelectriques depassant les limites applicables auxappareils numeriques de Classe A prescrites
dans le reglement sur le brouillage radioelectrique edicte parIndustrie Canada.
Class A equipment
This device has been tested and found to comply with the limits for a class A digital device pursuantPart 15 of
the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference when
the equipment is operated in a commercial environment. This equipmentgenerate, uses, and can radiate
radio frequency energy, and if not installed and used in accordancewith the instructions, may cause harmful
interference to radio communication. Operation of thisequipment in a residential area is likely to cause harm-
ful interference, in which case the user will berequired to correct the interference at personal expence.
However, there is no guarantee that interference will not occur in a particular installation. If thisdevice does
cause harmful interference to radio or television reception, which can be determined bytuning the device off
and on, the user is encouraged to try to correct the interference by on or more ofthe following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the device and receiver
•Connect the device into an outlet on a circuit different from that to which the receiver isconnected'Consult
the dealer or an experienced radio/television technician for help.
- 9 -

- 10 -
WEEE Symbol Statement
The symbol shown below is on the product or on its packaging, which indicates that this product
must not be disposed of with other waste. Instead, the device should be taken to the waste
collection centers for activation of the treatment, collection, recycling and disposal procedure.
The separate collection and recycling of your waste equipment at the time of disposal will help to
conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment for recycling,
please contact your local government office, your household waste disposal service or where you purchased
the product for details of environmentally safe recycling.
w When your electrical or electronic equipment is no longer useful to you, "take it back" to your local or
regional waste collection administration for recycling.
w If you need further assistance in recycling, reusing in your "end of life" product, you may contact us at the
Customer Care number listed in your product's user's manual and we will be glad to help you with your
effort.
Battery Warning: Incorrectly installing a battery or using incompatible battery may increase
the risk of ifre explosion. Replace the battery only with the same or equivalent type.
•Do not disassemble, crush, punchture batteries.
•Do not store or place your battery pack next to or in a heat source such as a fire, heatgenerating
appliance, can or exhaust vent. Heating battery cells to temperatures above 65oC (149oF) can
cause explosion or fire.
•Do not attempt to open or service batteries. Do not dispose of batteries in a fire or with house-
hold waste.

Hardware Installation - 11 -
1Installation Precautions
The motherboard/system contain numerous delicate electronic circuits and components which
can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully
read the service guide and follow these procedures:
•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty
validation.
•Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
•When handling the motherboard, avoid touching any metal leads or connectors.
•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap, keep your hands dry and first touch a metal object to eliminate static electricity.
•Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
•Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
•To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•Do not place the computer system on an uneven surface.
•Do not place the computer system in a high-temperature environment.
•Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
•If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
Chapter 1 Hardware Installation

- 12 - Hardware Installation
1-2 Product Specifications
CPU Support for Intel® Xeon® E5-2600 V3 series processors in the LGA2011 package
L3 cache varies with CPU
Supports Dual QuickPath Interconnect up to 9.6GT/s
Enhanced Intel SpeedStep Technology (EIST)
Support Intel Virtualization Technology (VT)
Chipset Intel® C612 Express (Wellsburg) Chipset
Memory 16 x 1.2V DDR4 DIMM sockets supporting up to 512GB RDIMM of system
memory
16 x 1.2V DDR4 DIMM sockets supporting up to 1TB LRDIMM of system memory
Four channel memory architecture
Supports DDR4 2133MHz RDIMM memory modules
Supports DDR4 2133MHz LR-DIMM memory modules
Support for ECC RDIMM/LRDIMM memory modules
LAN Intel® I350 supports 10/100/1000 Mbps
1 x Management LAN 10/100/1000Mpbs LAN port
Expansion Slot 2 x PCI Express x16 slot, running at x16 (Gen3/PCIE_1/PCIE_3)
2 x PCI Express x8 slot, running at x8 (Gen3/PCIE_2/PCIE_4, PCIE_2 Share
bandwidth with PCIE_3)
1 x PCI Express x8 slot, (Gigabyte extension slot/RAID_SLOT1/RAID_SLOT2/
GEN3)
Onboard
Graphics
ASPEED® AST2400 supports 16MB DDR3 VRAM
Mass Storage 12 x 3.5” Hot-Swap SATA HDDs (R270-C3C)
24 x 2.5” Hot-Swap SATA HDDs (R270-B2O)
System Fans 4 x 80x80x38mm/149000rpm
USB Up to 8 USB 3.0 ports (6 on the back panel, 2 additional ports via the USB
brackets connected to the internal USB headers)

1 x 24-pin ATX main power connector
2 x 8-pin ATX 12V power connector
2 x Mini-SAS connectors (SATA3 6Gb/s signal only)
8 x SAS connectors
2 x SATA3 6Gb/s connectors
1 x PMBus header
5 x System fan headers
1 x Front panel header
1 x HDD Back plane borad header
1 x USB 3.0 header
1 x TPM module connector
1 x Serial port connector
2 x SAS SPGIO headers
1 x IPMB connector
Rear Panel I/O 6 x USB 3.0 ports
3 x RJ-45 ports (1 x 10/100/1000 Mbps dedicated management LAN port)
1 x COM port
1 x VGA port
1 x PS/2 connector
Front Panel
LED/Buttons
1 x Power button/LED
1 x System status LED
1 x ID Switch button/LED
1 x Reset button
2 x LAN LEDs
1 x HDD status LED
I/O Controller ASPEED® AST2400 BMC chip
Hardware
Monitor
System voltage detection
CPU/System temperature detection
BIOS 1 x 128 Mbit flash
AMI BIOS
Environment
Ambient
Temperature
Relative
Humidity
Operating Temperature: 5oC to 35oC
Non-operating Temperature: 0oC to 50oC
10-80% operating Humidity at 30oC
System
Dimension
430Wx87Hx711.2D (mm)
Electrical
Power Supply
Hot-plug 2U PSU 750W 100-240VAC at 80 plus gold level
* GIGABYTE reserves the right to make any changes to the product specifications and product-related information
without
prior notice.
Hardware Installation - 13 -
Internal
Connectors

Hardware Installation - 14 -
1-3 System Block Diagram

- 15 - Hardware Installation
Chapter 2 System Hardware Installation
Pre-installation Instructions
Perform the steps below before you open the server or before you remove or replaceany
component.
•Back up all important system and data files before performing any hardwareconfiguration.
•Turn off the system and all the peripherals connected to it.
•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
•Apply an even and thin layer of thermal grease on the surface of the CPU.
•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
•Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU,
graphics card, memory, hard drive, etc.

Hardware Installation - 16 -
1 Removing Chassis Cover
Before you remove or install the system cover
•Make sure the system is not turned on or connected to AC power.
Follow these instructions to remove the system cover:
1. Loosen and remove the screws securing the back cover.
2. Loosen and remove the screws securing the front cover.
3. Remove the front cover.
4. Slide the back cover toward the rear of the chassis to disengage it.
5
3
1
23
4
5
3
1
23
4

Hardware Installation - 17 -
2-2 Removing and Installing the Fan Duct
Follow these instructions to remove/install the fan duct:
1. Loosen and remove the screws securing the screw.
2. Lift up to remove the fan duct
3. To install the fan duct, align the fan duct with the guiding groove. Push down the fan duct into
chassis until its firmly seats
1
2
2
1
2
2

- 18 - Hardware Installation
3Installing the CPU
Read the following guidelines before you begin to install the CPU:
•Make sure that the motherboard supports the CPU.
•Always turn off the computer and unplug the power cord from the power outlet before installing
the CPU to prevent hardware damage.
•Unplug all cables from the power outlets.
•Disconnect all telecommunication cables from their ports.
•Place the system unit on a flat and stable surface.
•Open the system according to the instructions.
WARNING!
Failure to properly turn off the server before you start installing components may cause serious
damage. Do not attempt the procedures described in the following sections unless you are a
qualified service technician.
Follow these instructions to install the CPU:
1. Raise the metal locking lever on the socket.
2. Remove the plastic covering on the CPU socket.Insert the CPU with the correct orientation. The
CPU only fits in one orientation.
3. Replace the metal cover.
4. Push the metal lever back into locked position.

Hardware Installation - 19 -
2-4 Installing the Heat Sink
Follow these instructions to install the heat sinks:
1. Apply thermal compound evenly on the top of the CPU.
2. Remove the protective cover from the underside of the heat sink.
3. Place the heat sink(s) on top of the CPU and tighten the four positioning screws.
WARNING!
•When you are installing the heat sink on the CPU, ensure the cooling fan is facing the rear I/O of
the system.
•Improper installation could cause system overheating and damage to equipment.