Pentax K 100D Super User manual

07.07 H.Y.
Product No.76706
TM
PENTAX Corporation
Service Technical Section
ENGLISH

76706 -1/6-
［ TABLE OF CONTENTS]
PREPARATION.................................................................................................................................2
1. Prepare SD card (3pcs) for confirming adjustment ..................................................................... 2
2 Setting the Computer and SD card........................................................................................................
DISASSEMBYAND ASSENBLY.....................................................................................................3
1．Replace 0-T100........................................................................................................................................ 3
2．Arrangement of lead wires on 0-T100..................................................................................................... 3
3．0-T770（SDM PCB）............................................................................................................................ 4
4．0-Q200 and related parts.......................................................................................................................... 4
5．A35（Dust collection sheet）................................................................................................................. 5
6．【Confirmation】CCD Base Plate Support Pillar C000 ........................................................................... 5
7．0-A301 ..................................................................................................................................................... 5
8．【Confirmation】Check the terminal of SDM.......................................................................................... 5
BATTERY CONSUMPTION ..............................................................................................................................6
Summary
K100D Super (76706) is basically same as K100D (76700).
K100D Super corresponds for SDM lens and equipped DR function.
Concerning the disassembly, assembly, adjustment procedure and technical information, please refer to the
service manual of K100D (76700).
The following spare parts are exclusive use for k100D Super. Refer to the parts list for k100D Super
◇Front cover right （A161） ◇ Plate (A162） ◇ Rear Cover（A201）
◇Dust collection sheet （A35）
◇SR/CCD block （0-C000） ◇ Main PCB （0-T100、76700-0-T100 can be used）
◇AF motor（0-S300）

76706 -2/6-
PREPARATION
1．Service tools, tester (Same as K100D except below adjustment software)
Adjustment software for 76706/76700 (SLR / Digital / SR) --- 95901 P412
If you already has adjustment software for K100D, the new software which correspond K100D
Super will provide automatically.
If you do not have adjustment software for K100D, please place order with 95901 P412
Preparation for adjustment
Preparation:
Adjustment software for 76706/76700
Personal computer
SD memory card 8MB x3
Camera and USB cable or SD card leader
1．Prepare the SD memory card x 3
1．Product firmware
2．Firmware for replaced T100
3．Writing initial data
Setting the Computer and SD card
① Delete previous adjustment software for K100D in the Computer
② Insert adjustment software for 76706/76700 to the computer and copy following folders into the C drive
『76700_706』・『76700_706 SLR』・『76700_706 SR Operation Adjustment』・
『76700_706 SR Gain Adjustment』
③ Copy 2 files to the SD card which in the「76700 Initial Data Set」folder
④ Copy『kb459b.bin』to the SD card which in the「GM_FW」folder
⑤ Copy『kb392.bin』to the SD card which in the「Product ID FW」folder
【Caution】VB runtime should be completed, refer to the service manual for K100D.
95901-P412

76706 -3/6-
DISASSEMBY AND ASSENBLY
1．Replace 0-T100
◆ When replaced T100, the following procedure is required
【Caution】
①Install FW for replaced T100
②Install product FW
③Initialize the data
Important note: It should be done from ①→②→③
2．Arrangement the lead wires on ０－T100
①x 3 ( Yellow, purple, blue)
②Arrange the lead wires as follows
Fix the lead wire by T66（BT6x15）and T65（BT6x8）
②
T66 T65 T66
T66
① 76700-0-T100 76706-0-T100
（76700-T100-07）
(0-T770)
Yellow
Violet
Blue
⇒

76706 -4/6-
①
3．0-T770（SDM PCB）
①0-T770
②Lead wires x 5
③DT(7x11)
④Lead wires x 2 (Red, Black)
⑤Lead wires x 2 (White, Brown)
⑥Arrange the lead wires as picture
4．0-Q200 and related parts
①PT(13x25)
③
①
Black ④
Red (Q200)
White ⑤
Brown (S300)
5 lead wires
(T770→T100)
2 lead wires
(Q200→T770)
②
Black
Red
Blue
Yellow
Violet
T200
0-T770

76706 -5/6-
① A39
5．A35（Dust collection sheet）
①Attach A35 x 2, refer to the picture
6．[CONF] CCD Base Plate Support Pillar
[Required equipment] Block gauge for 35mm, Dial gauge comparator, etc.
①Measure height of the CCD base support pillar (3 places) from the mount
surface as shown in the figure.
Standard 49.610±0.02 mm
Use block gauge for 35mm,
（45.46mm）
＋4.15 ±0.02 mm
（+4.13～4.17 mm）
7．Arrange the lead wires
① Fix the flex with A39 (BT 6x10)
② Arrange the lead wires as picture
8．【Confirmation】Terminal for SDM
＊Attach SDM lens and check the function of SDM
+4.
+4.15
+0.15

76706 -6/6-
Battery consumption current
Condition : Lens [FA lens, A position], each mode and setting is default setting.
Lens---- ○: With ×: Without
SD card---- ○: With ×: Without
＊5,6 and 7 are peak value averages
Condition of camera Lens SD card Battery
DC5.5V
AC Power
supply
DC6.5V
○× 50μA 10mAMain SW/OFF
○○50μA 10mA
1
× × 50μA 10mA
○× 250μA 10mA2 After auto power OFF
× × 250μA 10mA
Main SW/ON（Meter OFF）○× 180mA 240mA
○○180mA 240mA
3
× × 180mA 240mA
Main SW/ON（Meter ON）○× 370mA 420mA4
○○370mA 420mA
5 Charging Flash（Meter ON）＊ ○× 2,100mA 2,200mA
6 Driving AF motor ＊○× 2,200mA 2,300mA
7 Operating SDM ○AF
○MF
×
×
3,500mA
2,200mA
3,500mA
2,200mA
Releasing shutter ＊○× 3,000mA 3,200mA8
○○3,000mA 3,200mA
9 Recording image after release the
shutter
○○350mA 350mA
Bulb ○× 1,200mA 1,200mA10
○○1,200mA 1,200mA
11 Displaying menu (LCD) ○× 500mA 450mA
12 Displaying menu (Video output) ○× 400mA 350mA
13 Displaying playback image ○○500mA 450mA
14 Recording playback image in the card ○○500mA 450mA
15 Stand by for USB communication ○○300mA 300mA
16 Reading playback image in the card
with USB communication
○○350mA 300mA