PEP Modular Computers CP341 User manual

CP341
Dual-Port Ethernet/Fast Ethernet Board
for CompactPCI Applications
Manual ID 18845, Rev. Index 0102
20 Nov 98
The product described in this manual is
in compliance with all applied CE stan-
dards.

® PEP Modular Computers GmbH
This page was intentionally left blank.

CP341 Preface
Preface
Revision History........................................................... 0 - 4
Trademarks.................................................................. 0 - 4
Explanation of Symbols ............................................... 0 - 5
For Your Safety............................................................ 0 - 6
High Voltage Safety Instructions.............................. 0 - 6
Special Handling and Unpacking Instructions.......... 0 - 6
General Instructions on Usage................................. 0 - 7
Two Years Warranty .................................................... 0 - 8
Table of Contents......................................................... 0 - 9
ID 18845, Rev. 0102 Page 0 - 3® PEP Modular Computers GmbH

Preface CP341
Revision History
This document contains information proprietary of PEP Modular Computers. It may not be
copied or transmitted by any means, disclosed to others or stored in any retrieval system or
media, without the prior written consent of PEP Modular Computers GmbH or one of its autho-
rized agents.
The information contained in this document is, to the best of our knowledge, entirely correct.
However, PEP Modular Computers cannot accept liability for any inaccuracies, or the conse-
quences thereof, nor for any liability arising from the use or application of any circuit, product,
or example shown in this document.
PEP Modular Computers reserve the right to change, modify, or improve this document or the
product described herein, as seen fit by PEP Modular Computers without further notice.
Trademarks
PEP Modular Computers, the PEP logo and “CXM” are trade marks owned by PEP Modular
Computers GmbH, Kaufbeuren (Germany). In addition, this document may include names,
company logos and trademarks, which are registered trademarks and, therefore, proprietary
of their respective owners.
ID 18845, Rev. 0102Page 0 - 4 ® PEP Modular Computers GmbH
Revision History
Manual/Product Title: CP341
Manual ID Number: 18845
Rev.
Index Brief Description of Changes Board Index Date of Issue
0100 Initial Issue 00 00 Nov. 98
0101 Tables of Contents Amended 00 00 Nov. 98
0102 Preface; ID Electronic/Paper; Sections 3.1-3.2 00 00 Nov. 98

PrefaceCP341
ID 18845, Rev. 0102 Page 0 - 5® PEP Modular Computers GmbH
Explanation of Symbols
CE Conformity
This symbol indicates that the item described in this manual
is in compliance with all applied CE standards. See also the
section “Applied standards” of this manual.
Caution!
This symbol and title warn you of hazards due to electrical
shocks (> 60 V) when touching products or parts of them.
The non-observance of the measures indicated and/or pre-
scribed by the law may cause harm to your product and/or
life/health.
See also the section “High Voltage Safety Instructions”.
ESD-Sensitive Device!
This symbol and title inform you that electronic boards and
their components are sensitive to static electricity. There-
fore, care must be taken during all handling operations and
inspections of this product, in order to ensure product integ-
rity at all times.
Please read also the section “Special Handling and Unpack-
ing Instructions” of this manual.
Attention!
This symbol and title emphasize aspects which, if not read
through carefully by the reader, might cause hazards to
health and/or damages to material.
Note:
This symbol and title emphasize aspects the reader should
read through carefully for his or her own advantage.
PEP Advantage
This symbol and title emphasize advantages or positive
aspects of a product and/or procedure.
Troubleshooting
This symbol and title characterize a message containing
useful information on troubleshooting and problem solving.
!
$

CP341Preface
For your safety
Your new PEP product was developed and tested carefully to provide all features necessary
to ensure the renown electrical safety requirements. It was also designed for a long fault-free
life. However, the life expectancy of your product can be drastically reduced by improper treat-
ment during unpacking and installation. Therefore, in the interests of your own safety and of
the correct operation of your new PEP product, you are requested to conform with the follow-
ing guidelines.
High Voltage Safety Instructions
Special Handling and Unpacking Instructions
$Do not handle this product out of its protective enclosure while it is not used for opera-
tional purposes, unless it is otherwise protected.
$Whenever possible, unpack or pack this product only at EOS/ESD safe work stations.
Where safe work stations are not guaranteed, it is important for the user to be electri-
cally discharged before touching the product with his/her hands or tools. This is most
easily done by touching a metal part of your system housing.
$It is particularly important to observe standard anti-static precautions when changing
piggybacks, ROM devices, jumper settings etc. If the product contains batteries for RTC
or memory back-up, ensure that the board is not placed on conductive surfaces, includ-
ing anti-static plastics or sponges. They can cause short circuits and damage the batter-
ies or tracks on the board.
Warning!
All operations on this device must be carried out by sufficiently
skilled personnel only.
Caution!
However, serious electrical shock hazards exist during all installa-
tion, repair and maintenance operations with this product. There-
fore, always unplug the power cable to avoid exposure to
hazardous voltage.
Before installing your new PEP product into a system always
ensure that your mains power is switched off. This applies also to
the installation of piggybacks.
ESD Sensitive Device!
Electronic boards and their components are sensitive to static
electricity. Therefore, care must be taken during all handling oper-
ations and inspections of this product, in order to ensure product
integrity at all times.
!
ID 16566, Rev. 0102Page 0 - 6 ® PEP Modular Computers GmbH

PrefaceCP341
General Instructions on Usage
$In order to maintain PEP’s product warranty, this product must not be altered or modified
in any way. Changes or modifications to the device, which are not explicitly approved by
PEP Modular Computers and described in this manual or received from PEP Technical
Support as a special handling instruction, will void your warranty.
$This device should only be installed in or connected to systems that fulfill all necessary
technical and specific environmental requirements. This applies also to the operational
temperature range of the specific board version, which must not be exceeded. If batter-
ies are present, their temperature restrictions must be taken into account.
$In performing all necessary installation and application operations, please, follow only
the instructions supplied by the present manual.
$Keep all the original packaging material for future storage or warranty shipments. If it is
necessary to store or ship the board please re-pack it as nearly as possible in the man-
ner in which it was delivered.
$Special care is necessary when handling or unpacking the product. Please, consult the
special handling and unpacking instruction on the following page of this manual.
ID 18845, Rev. 0102 Page 0 - 7® PEP Modular Computers GmbH

CP341Preface
Two Years Warranty
PEP Modular Computers grants the original purchaser of PEP products a TWOYEARSLIMITED
HARDWAREWARRANTYas described in the following. However, no other warranties that may be
granted or implied by anyone on behalf of PEP are valid unless the consumer has the express
written consent of PEP Modular Computers.
PEP Modular Computers warrants their own products, excluding software, to be free from
manufacturing and material defects for a period of 24 consecutive months from the date of
purchase. This warranty is not transferable nor extendible to cover any other users or long-
term storage of the product. It does not cover products which have been modified, altered or
repaired by any other party than PEP Modular Computers or their authorized agents. Further-
more, any product which has been, or is suspected of being damaged as a result of negli-
gence, improper use, incorrect handling, servicing or maintenance, or which has been
damaged as a result of excessive current/voltage or temperature, or which has had its serial
number(s), any other markings or parts thereof altered, defaced or removed will also be
excluded from this warranty.
If the customer’s eligibility for warranty has not been voided, in the event of any claim, he may
return the product at the earliest possible convenience to the original place of purchase,
together with a copy of the original document of purchase, a full description of the application
the product is used on and a description of the defect. Pack the product in such a way as to
ensure safe transportation (see our safety instructions).
PEP provides for repair or replacement of any part, assembly or sub-assembly at their own
discretion, or to refund the original cost of purchase, if appropriate. In the event of repair,
refunding or replacement of any part, the ownership of the removed or replaced parts reverts
to PEP Modular Computers, and the remaining part of the original guarantee, or any new
guarantee to cover the repaired or replaced items, will be transferred to cover the new or
repaired items. Any extensions to the original guarantee are considered gestures of goodwill,
and will be defined in the “Repair Report” issued by PEP with the repaired or replaced item.
PEP Modular Computers will not accept liability for any further claims resulting directly or indi-
rectly from any warranty claim, other than the above specified repair, replacement or refund-
ing. In particular, all claims for damage to any system or process in which the product was
employed, or any loss incurred as a result of the product not functioning at any given time, are
excluded. The extent of PEP Modular Computers liability to the customer shall not exceed the
original purchase price of the item for which the claim exists.
PEP Modular Computers issues no warranty or representation, either explicit or implicit, with
respect to its products’ reliability, fitness, quality, marketability or ability to fulfil any particular
application or purpose. As a result, the products are sold “as is,” and the responsibility to
ensure their suitability for any given task remains that of the purchaser. In no event will PEP
be liable for direct, indirect or consequential damages resulting from the use of our hardware
or software products, or documentation, even if PEP were advised of the possibility of such
claims prior to the purchase of the product or during any period since the date of its purchase.
Please remember that no PEP Modular Computers employee, dealer or agent is authorized to
make any modification or addition to the above specified terms, either verbally or in any other
form, written or electronically transmitted, without the company’s consent.
ID 18845, Rev. 0102Page 0 - 8 ® PEP Modular Computers GmbH

CP341 Preface
ID 18845, Rev. 0102 Page 0 - 9® PEP Modular Computers GmbH
Table of Contents
Chapt 1
Chapter 1
1. Introduction............................................................ 1 - 3
1.1 System Overview............................................. 1 - 3
1.2 System Components....................................... 1 - 4
1.3 Board Introduction........................................... 1 - 7
1.4 Board Overview............................................... 1 - 7
1.5 Main Features.................................................. 1 - 8
1.6 Main Features................................................ 1 - 10
1.7 Applied Standards......................................... 1 - 11
1.8 Related Publications...................................... 1 - 11
Chapter 2
2. Configuration......................................................... 2 - 3
Chapter 3
3. Installation............................................................. 3 - 3
3.1 Hardware Installation....................................... 3 - 3
3.2 Driver Installation............................................. 3 - 5
3.3 Troubleshooting............................................... 3 - 7

® PEP Modular Computers GmbH
This page was intentionally left blank.

CP341 Introduction
Introduction
ID 18845, Rev. 0102 Page 1 - 1® PEP Modular Computers GmbH
1.1 System Overview.................................................................. 1 - 3
1.1.1 Note on CompactPCI................................................... 1 - 3
1.1.2 Main Features of CompactPCI Systems...................... 1 - 3
1.2 System Components............................................................ 1 - 4
1.3 Board Introduction................................................................ 1 - 7
1.4 Board Overview.................................................................... 1 - 7
1.5 Main Features ...................................................................... 1 - 8
1.5.1 LAN Controller ............................................................. 1 - 8
1.5.2 Memory........................................................................ 1 - 8
1.5.3 Board Interfaces........................................................... 1 - 8
1.5.4 Front Panel .................................................................. 1 - 9
1.6 Specifications ..................................................................... 1 - 10
1.7 Applied Standards.............................................................. 1 - 11
1.7.1 CE Compliance.......................................................... 1 - 11
1.7.2 Mechanical Compliance............................................. 1 - 11
1.7.3 Environmental Tests.................................................. 1 - 11
1.8 Related Publications........................................................... 1 - 11
Chapter1

® PEP Modular Computers GmbH
This page was intentionally left blank.

CP341 Introduction
ID 18845, Rev. 0102 Page 1 - 3® PEP Modular Computers GmbH
1. Introduction
1.1 System Overview
The PEP Modular Computers CompactPCI systems described in this chapter operate
with the PCI bus architecture to support additional I/O and memory-mapped devices as
required by various industrial applications. In the following you will find the most impor-
tant information on all system-relevant CompactPCI features. For more detailed infor-
mation concerning the CompactPCI standard, please consult the complete Peripheral
Component Interconnect (PCI) and CompactPCI Specifications. You can connect to the
homepage of the PCI Industrial Computer Manufacturers Group (PICMG) by clicking
into the highlighted area.
1.1.1 Note on CompactPCI
CompactPCI is an extension of the PCI specification. It has been optimized for industrial
and/or embedded applications that require a more robust mechanical form factor as
compared to Desktop PCI. CompactPCI systems use industry standard mechanical
components and high performance connector technologies to provide systems that are
well suited for rugged applications. CompactPCI stands for systems that are electrically
compatible with the PCI Specification, allowing low-cost PCI components to be used.
CompactPCI is an open specification supported by the PICMG, which is a consortium of
companies involved in utilizing PCI for embedded applications.
1.1.2 Main Features of CompactPCI Systems
Some of the outstanding features of the CompactPCI systems compliant with Specifica-
tion 2.0, Release 2.1 are:
•PCI signalling
•32- and 64-bit data transfer at 33 MHz
•up to 8 PCI slots per backplane
•industry standard software support
•3U small form factor (100 mm by 160 mm)
•6U form factor (233 mm by 160 mm)
•Eurocard packaging
•wide variety of available I/O functions

CP341 Introduction
ID 18845, Rev. 0102Page 1 - 4 ® PEP Modular Computers GmbH
•industry support from over 350 members.
1.2 System Components
PEP Modular Computers have devised their CompactPCI systems as a comprehensive
open solution for industrial environments, offering different workstation configurations
which are capable of including all the components necessary to fulfill the requirements
of virtually all existing system functionalities.
CompactPCI Backplane(s)
•4-slot backplane;
•6-slot backplane;
•8-slot backplane;
•16-slot backplane.
CPU Function
PEP Modular Computers provides CPU boards corresponding in size and characteris-
tics to the special features of the PEP systems.
Display-Related Functions
Display-related functions such as graphics control and frame grabbing are supported by
dedicated boards.
Communication
Communication boards are provided for the currently relevant industrial communication
systems such as, for instance, Fast Ethernet.
Fieldbus Control
Fieldbus control boards provide data exchange with field control and automation sub-
systems like, for example, PEP Modular Computers’ SMART2 or VMEbus systems,
using up-to-date transmission standards e.g.:
•CAN fieldbus control
•PROFIBUS control
Industrial I/O Functions
PEP’s CompactPCI systems support an ever increasing number of industrial I/O func-
tionalities in the fields of:
PEP Advantage
PEP Modular Computers’ CompactPCI systems are designed as
open systems, able to be expanded at any time, so that their back-
planes can be equipped with precisely the CPCI boards that corre-
spond to a customer’s specific needs. However, in order to supply
you with an appropriate choice of workstations, the PEP basic
equipment is divided into pre-configured sets and custom solutions.

CP341 Introduction
ID 18845, Rev. 0102 Page 1 - 5® PEP Modular Computers GmbH
•Digital I/O
•Analog I/O
Self-Testing
A special PEP self-testing board provides a trouble-spotting capability within your PEP
system.
System Hardware
The PEP CompactPCI system hardware includes housings, storage devices, power
supply units, network adapters etc. The most important system hardware elements with
which to configure your CompactPCI system are as follows:
Multiprocessor
In a CompactPCI multi-processer system, a system controller (CP610) communicates
with other CPU’s through a non-transparent PCI / PCI bridge
Housings
•Board cages for 19-inch or wall mounting
•PCI tower
•PCI desktop housing
Mass Storage Devices
•Hard-disk drive
•Floppy-disk drive
•CD-ROM drive
Power Supply Units
•19-inch “M”, 180 W, 120/230 V AC, 3.3V/14A, 5.1V/20A, 12V/2A, -12V/1A
•“ATX”, 235 W, 120/230 VAC, 3.3V/14A, 5V/22A, 12V/8A,-12V/1A, -5V/0.5A,
5VSB/0.1A
Please note that the following units of measurement are used to express the dimensions
of PEP cards and housings:
•Height: 1 U = 44.45 mm
•Width: 1 HP = 5.08 mm
For a detailed description of the PEP Modular Computers CompactPCI modules please
consult the specific components’ manuals or data sheets.
PEP Advantage
As the PEP Modular Computers CompactPCI system provides
comprehensive open solutions, new features and functionalities
may be added to our range. To keep abreast of the latest develop-
ments, please contact your local PEP Sales Office or visit the PEP
Web Site.

CP341 Introduction
ID 18845, Rev. 0102Page 1 - 6 ® PEP Modular Computers GmbH
Figure 1-1: Example of a PEP Modular Computers CompactPCI System
ImageControl
WD Timer
HDD FDD CD-ROM COM LPT Keyboard
SMART2 SMART I/O PEP9300
Host Computer
CompactPCI Workstation
WWW
CPU Server
Computer
Fast Ethernet
VGA LVDS
Graphics
F.Ethernet
Communic. RGB
SYNC
IndustrialI/O
Digital I/O Analog I/O
CPCI Backplane
Fieldbus
PROFIBUS CAN
Host Computer
Multi
Processor

CP341 Introduction
ID 18845, Rev. 0102 Page 1 - 7® PEP Modular Computers GmbH
1.3 Board Introduction
The CP-341 board by PEP Modular Computers is a CompactPCI network controller
based on the Intel Fast Ethernet PCI Bus LAN Controller 82558.
Some of the CP341’s outstanding features are:
•Dual independent Fast Ethernet interfaces
•Multiple server-to-client networking
•10Base-T and 100Base-TX auto-negotiation
•Integrated physical layer interface (PHY)
•6 kByte FIFO buffer
•Galvanic de-coupling
1.4 Board Overview
The CP341 board by PEP Modular Computers is a Compact PCI Fast Ethernet LAN
controller for multiple server-to-client networking functions. It provides dual independent
fast Ethernet Interfaces. Both interfaces are based on the Intel Fast Ethernet PCI Bus
LAN Controller 82558 with integrated physical layer interface (PHY).
CP341 is a 3U CPCI Ethernet board suitable for both 10Base-T and 100Base-TX con-
nections and includes all necessary features for auto-negotiation. Thus, both 10 Mbit/s
and 100 Mbit/s transfer rates are supported by the board. In fact, provided that your net-
work has the speed capability, the CP341 switches automatically from 10 Mbit/s to 100
M/bit/s. Additionally, if the addressed network station is compatible, it switches automat-
ically to full-duplex mode.
The 3.3V/5V signalling board is designed to permit a very high PCI data bandwidth,
which is achieved thanks to a large, 3 kByte-in/3 kByte-out FIFO buffer.
An Advanced Configuration Power Interface (ACPI) guarantees various power-down
states and the ability to wake up on a single package addressed to the system, while
remote stations may be returned to full power by any remote machine being networked.
The board does not have any jumpers and, therefore, does not require configuration.
This is due to the use of a standard Windows NT driver (both Windows NT 3.5 and 4.0
drivers are supplied with the board). To make installation, repairs and updates easier, a
LANDesk Service Agent allows the system to be started from a different operating sys-
tem via network.

CP341 Introduction
ID 18845, Rev. 0102Page 1 - 8 ® PEP Modular Computers GmbH
Figure 1-2: CP341 Functional Block Diagram
1.5 Main Features
The following description illustrates the main features of the principal functional blocks
of the CP341 LAN controller board.
1.5.1 LAN Controller
The Intel 82558 is the first fully integrated combination 32-bit PCI bus LAN controller
and physical layer interface for 10/100Mbps Fast Ethernet networks. It is characterized
by advanced control features for high performance and outstanding reliability.
1.5.2 Memory
The board conception includes hardware support for an optional FLASH memory up to
two times 64 kByte.
1.5.3 Board Interfaces
Figure 1-3: RJ45 Ethernet/Fast Ethernet Connector
The CP341 is provided principally with two RJ45 network communication
connectors for Ethernet or Fast Ethernet, to which your system’s communi-
cation lines are connected.
CPCI Bus
FLASH
EEPROM
F.Ethernet
Galvanic
F.Ethernet
LEDsLEDs
Coupling
FLASH
EEPROM
Galvanic
Decoupling
LAN
Controller
LAN
Controller
PCI-to-PCI
Bridge

CP341 Introduction
ID 18845, Rev. 0102 Page 1 - 9® PEP Modular Computers GmbH
Ethernet and Fast Ethernet
The CP341 LAN controller board envisages the use of the renown CSMA/CD protocol
(Carrier Sense Multiple Access/Collision Detection), enabling data to move between
Ethernet and Fast Ethernet nodes on the LAN without any protocol translation.
Ethernet and Fast Ethernet are ruled by standards issued by IEEE (Institute of Electrical
and Electronic Engineers). Ethernet supports a transfer speed of 10 Mbit/s, Fast Ether-
net of 100 Mbit/s.
Cable Types
CP341 is designed to support star topology 2-pair category 5 UTP/STP cables which
are one of the most widely available cable types on the market.
”UTP” stands for ”Unshielded Twisted-Pair” cables, while ”STP” stands for ”Shielded
Twisted-Pair” cables. The purpose of wire twisting and shielding is to reduce electro-
magnetic interference between cable wires.
1.5.4 Front Panel
Figure 1-4: CP341 Front Panel View
The CP341 front panel is provided with two Ethernet/Fast Ethernet
RJ45 LAN connectors, while three control LEDs are associated with
each of them in order to allow monitoring the board activity. The LEDs
have the following functions:
•LINK “ON” = LAN link is integer;
•ACT “ON” = board is active;
•SPEED “ON” = transfer speed corresponds to 100 Mbit/s.
PEP Advantage
A power indicator on the front panel is not neces-
sary, since the board is provided with an advanced-
configuration power interface (ACPI) which guaran-
tees various power-down states and the ability to
wake up on a single package addressed to the sys-
tem, while remote stations may be returned to full
power by any remote machine of the network.
Also there is no collision indicator on the front
panel, since the frequency of network collisions is
reduced to a minimum thanks to the CSMA/CD pro-
tocol enabling data to move evenly between Ether-
net and Fast Ethernet nodes on the LAN without
protocol translation.

CP341 Introduction
ID 18845, Rev. 0102Page 1 - 10 ® PEP Modular Computers GmbH
1.6 Specifications
Table 1-1: CP341 Specifications
CP341 Specification
Windows NT Compatibility Hardware design for WinNT network interface chip driver
(NIC) according to Windows and WinNT network driver
interface specification (NDIS)
Ethernet IEEE Standard 10 Mbit/s 802.3 and 100 Mbit/s 802.3u
Compact PCI Interface Peripheral board interface;
32-bit bus address/data/33 MHz
INT A/INT B support;
IDSEL hardware support;
CPCI data burst rate close to 132 MByte/s
1 4TE slot
Signalling Voltage 3.3V/5 V
Plug & Play Design No jumpers to be configurated
Remote Boot 2 x EEPROM/FLASH socket, 64 kByte max. each
Speed Configuration Auto-speed sensing/switching
Wake-up on LAN (Remote
Wake-up) Package detection logics reacting on incoming packages
Front-Panel Connector 2 x RJ-45, with 2-pair 5 UTP/STP cable pinout each
Mechanical Compliance IEEE 1101.10
Power Supply 3.3V/5 V, codes according to CPCI specification
Temperature Range
- Operation
- Storage •0° to +60°C (standard)
•-55° to +85°C
Operating Humidity 5 - 95% (non-condensing)
Vibrations IEC68-2-6 compliant
Shocks:
- Permanent Shocks
- Single Shocks IEC68-2-29 IEC68-2-27
Board Dimensions Single-height Eurocard: 100 mm x 160 mm