Perenio UV Mini Indigo User manual

Installation and Operation Manual for
Perenio®Portable UV Lamp
UV Mini Indigo
(Article: PEMUV01, PEMUV02)
February, 2021

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 3из 25
Introduction
The Portable UV Lamp is a low-pressure mercury lamp designed to kill germs and
dust mites with ultraviolet radiation at the site of installation.
The present Manual contains a detailed description of the device, as well as
instructions for its installation and operation.
Copyrights
Copyright of ©Perenio IoT spol s r.o.All rights reserved.
The Perenio®Smart Health trademark is owned by Perenio IoT spol s r.o.
(hereinafter referred to as the Perenio IoT). All other similar trademarks and names,
as well as logos and other symbols are the property of their respective owners*.
All materials under Perenio®Smart Health tradename contained therein are
protected in accordance with international and local laws including Acts on Copyrights
and related rights.
Any reproduction, copying, publication, as well as further distribution or public display
of material contained in the present document (whether in full or in part) shall not
be allowed until an appropriate permission of the copyright owner is obtained.
Any unauthorized usage of materials contained herein may lead to civil liability and
criminal prosecution in accordance with applicable laws.
Any eventual mentioning of other company names and equipment in the present
document is made solely for the purpose of clarifying and describing the device
operation and shall not infringe on the third party’s intellectual property rights.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 4из 25
Responsibility and Technical Support
The present document is prepared in accordance with all necessary requirements and
contains detailed information on the device installation, configuration and control
valid as of the date of its issue.
Perenio IoT reserves the right to modify the device and make corrections or changes
to this document without prior notice of the User, and shall not be responsible for
any potential negative consequences which may arise from the use of an outdated
version of the document, as well as for any possible technical and/or typographical
errors, either omitted or accidental, or any related damage that may result from the
document transfer or the use of the devices.
Perenio IoT shall make no guarantee with respect to any data contained herein
including but not limited to the device merchantability and fitness for a particular
purpose.
For any technical issues, please contact your local Perenio IoT representative or the
Tech Support Department at perenio.com.
The most common problems may be found in Section 8 of the present document and
at perenio.com where you can also download the latest version of this Installation
and Operation Manual.
Manufacturer:
Perenio IoT spol s r.o.
Na Dlouhem 79, Ricany –Jazlovice 251 01, Czech Republic
perenio.com

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 5из 25
Conformance to Standards
The device is CE certified and complies with the 2014/30/EU
Electromagnetic Compatibility Directive of the European Union
The device complies with the UKCA marking requirements for
selling the device in the UK
The device has passed all procedures of assessments established
in Technical Regulations of the Customs Union and conforms with
standards of the Customs Union
The device complies with the requirements of Restriction of the Use
of Certain Hazardous Substances (RoHS) in Electronic and Electrical
Equipment (2011/65/EU Directive)
The device and supplied batteries must not be disposed of as a
household waste in accordance with the Waste Electrical and
Electronic Equipment Directive (2002/96/EC)
For the purpose of protection of the environment and human
health, both the device and batteries must be disposed of in
accordance with approved instructions on safe disposal. For more
information on proper disposal, please contact your device supplier
or local authorities responsible for waste management.
Information about certificates received is
indicated in section 7 of this document. Copies
of certificated and declarations can be found in
the appropriate section on the website
perenio.com
BG
CZ
DE
ES
FR
GR
IT
KZ
LT
LV
NL
NO
PL
RO
RU
SE
SK
TR
UA
UK

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 6из 25
Warnings and Restrictions
Prior to installation and operation of the device, the User shall carefully read and
understand information contained herein.
ATTENTION! The warnings, precautions, and instructions contained in this
document may not contain every possible hazardous situation. Use common sense
when using the device.
Safety Operation Rules
1. The device shall be used as described in this manual only. Any other use not
specified therein may cause fire and other hazards, as well as injury to persons.
2. Ventilate the room for at least 30 minutes after the UV lamp stops working.
3. It is forbidden to operate the device, if any part of the device is damaged or cracked.
4. The device shall not be installed outdoors, or near water including humidifiers.
5. The device shall be kept away from direct sunlight, moisture and vibration.
6. It is not allowed to drop or throw the device, as well as attempt to repair it on
one’s own.
7. It is not allowed to use the device with a damaged USB-MicroUSB cable, or put
this cable near radiators, stoves or heaters.
8. It is not allowed to use detergents to clean any part of the device.
9. If the UV tube is broken, all particles shall be swept into a plastic bag, sealed
and disposed of properly, as well as the room must be well-ventilated, because
the device contains mercury. Do not use a vacuum cleaner to pick up the waste
and glass particles. Contact your local waste collection agency for proper
disposal procedures.
10. Keep children away from the device, because it may emit a light attractive to
them. Serious injury and electrocution might be possible. This device is
intended to be operated by adults only.
Warnings and Precautions
1. The Portable UV Lamp is not a medical device.
2. People, pets and plants must not be present in the room under UVC and/or
ozone exposure.
3. It is forbidden to look at the working UV tube, as any exposure to
ultraviolet radiation will cause serious damage to the eyes and may
lead to skin damage. Therefore, when the device is turned on, wear
appropriate eye and skin protection from UV rays.
4. Ingestion or contact with mercury or its vapor is hazardous to health.
5. It is forbidden to touch the UV tube with wet hands.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 7из 25
6. The device is not intended to be used for removal of active mold growth. The
UVC light exposure to existing mold growth can cause respiratory irritation and
allergic symptoms.
7. The UVC light exposure may also cause fabric and painting discoloration.
8. The UVC light of the device does not provide a tanning effect, while its exposure
to uncovered skin areas for more than 2-3 minutes will cause burns.
9. Do not use incompatible USB Charger to recharge the device.
Warnings related to Ozone and UV
The germicidal effect of the Portable UV Lamp UV Mini Indigo is provided by the
use of UVC wavelengths of 185nm and 253.7nm.
UV light with a wavelength of 253.7nm is one of the most effective in destroying cells
of pathogenic organisms. And UV light with a wavelength of 185 nm produces ozone
in the air, which is effective in destroying microorganisms and removing odors. This
type of disinfection does not harm the environment and does not require special
maintenance and storage conditions.
However, ozone is highly toxic and can have adverse effects on human health, such as:
•Chest pains, cough, shortness of breath, and throat irritation;
•Chronic respiratory diseases such as asthma;
•Decreased ability of the body to fight respiratory infections;
•Inflammation and damage to the mucous membrane of the lungs.
Exposure to ultraviolet radiation can cause the following adverse effects:
•Skin and eye burns;
•Various mutations (skin cancer, skin melanoma, premature aging).
Therefore, extreme care and precautions must be taken when using Portable UV
Lamp UV Mini Indigo. All instructions from this document must be followed.
Warnings related to the use of a power adapter
1. Only a suitable power adapter* shall be used to charge the device.
2. It is not allowed to connect a USB-PD (Power Delivery rapid charge standard)
power adapter to the device.
3. The manufacturer shall not be liable for any consequences, whether direct or
indirect, arising from the use of an incompatible adapter to supply power or
recharge the device.
NOTE. If a portable charger is used to recharge the UV lamp, make ensure that
the charger output parameters meet the UV lamp power source requirements*.
* For more information on the charger, please see the description in the table of specifications.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 8из 25
Table of Contents
Introduction ................................................................................................ 3
Copyrights................................................................................................... 3
Responsibility and Technical Support............................................................... 4
Conformance to Standards............................................................................. 5
Warnings and Restrictions ............................................................................. 6
Table of Contents ......................................................................................... 8
1 General Description and Specifications........................................................ 10
1.1 Device Purpose .................................................................................. 10
Buttons, Ports and Indicators.................................................................. 12
1.2 Technical Specification ........................................................................ 12
1.3 Scope of Delivery ............................................................................... 14
1.4 Packaging and Labelling ...................................................................... 14
2. Installation and Setup ............................................................................. 15
2.1 Preconditions for UV Treatment ............................................................ 16
2.2 UV Treatment Process......................................................................... 16
2.2.1 Recommended Exposure Time ........................................................ 17
3 Maintenance and Repair............................................................................ 18
4 Warranty Obligations................................................................................ 19
5 Storage, Transportation and Disposal of Devices .......................................... 22
6 Other Information.................................................................................... 23
7 Troubleshooting....................................................................................... 24
8 Glossary................................................................................................. 25
Figures and Tables
Figure 1 - Exterior ...................................................................................... 11
Figure 2 –Buttons, Ports and Indicators ........................................................ 12
Figure 3 –Scope of Supply .......................................................................... 14
Figure 4 –Examples of installation................................................................ 15

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 9из 25
Table 1 –Portable UV Lamp LED Indicator statuses..........................................12
Table 2 –Basic Technical Specifications of the Portable UV Lamp .......................12
Table 3 –Recommended Exposure Time.........................................................17
Table 4 –Typical Errors and Troubleshooting Methods ......................................24

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 10 из 25
1 General Description and Specifications
1.1 Device Purpose
Perenio® Smart Health UV Mini Indigo Portable UV Lamp is a low pressure
mercury lamp designed to destroy bacteria*, germs and dust mites with ultraviolet
radiation and ozone at the site of installation.
The lamp operates at short-wave ultraviolet light.
The 253.7nm wave destroys microorganisms by irradiating their DNA and
chromosomes, while the 187nm wave produces ozone, which oxidizes the air, thereby
destroying bacteria and germs, and removing odor even in places that are hard to
reach.
Key functional features of the Portable UV Lamp are:
•Disinfection by ultraviolet and ozone;
•UV tube lifespan –up to 15000 hours;
•Operation from a built-in battery and/or an external power source;
•The ability to recharge from other compatible devices (Laptop, PC, portable
charging devices);
•Automatic turn-on delay timer (15 seconds);
•Automatic shutdown of the UV Lamp after 30 minutes of operation;
•Ease of use –no configuration required;
•Compact design and the ability to destroy germs and odors in small objects
(Wardrobe, fridge, car).
ATTENTION! All Products and the Mobile Application of the Company (including
any future software and hardware whether in-house or third-party developed) are
not intended for emergency responses and cannot be used as fire-extinguishing
equipment and/or for emergency intervention, including but not limited to fires,
flooding, gas leaks or explosions, burglary and theft, as well as natural disasters
and other force majeure circumstances leading to damage and/or losses incurred
by the Client or caused to their estates, personal property and/or other products,
devices, personal data and privacy.
* The maximum death rate of Escherichia coli and Staphylococcus aureus bacteria (up to 99.9%) is achieved when being
exposed to the UV lamp for 30 minutes at a distance of 5 cm from the UV tube.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 11 из 25
Figure 1 - Exterior
2-a –Front View 2-b –Back View
UV tube
MicroUSB
port
LED
Indicator
Power Button

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 12 из 25
Figure 2 –Buttons, Ports and Indicators
Buttons, Ports and Indicators
LED Indicator
Indicator of various device states (See Table 1)
Power Button
Button used to turn on and off the UV Lamp
UV Tube
UV Lamp element made of quartz glass that generates UV rays
and ozone
MicroUSB Port
Port for connecting the device to a power source
Table 1 –Portable UV Lamp LED Indicator statuses
Indicator
Status
Description
Blue
Blinking
Turn-on delay timer is running
On
UV treatment is in progress
Off
Device is turned off
Damage to the UV tube if the indicator goes out in
15 seconds after the lamp is turned on
Damage to the UV Lamp or built-in battery, if the
indicator does not light up at all after pressing the power
button
Red
Blinking
Device is discharged
Charging in progress
1.2 Technical Specification
Table 2 –Basic Technical Specifications of the Portable UV Lamp
Parameter
Value
Article
PEMUV01 (white color), PEMUV02 (black color)
Type
Low pressure mercury lamp
UV tube
Bulb type: Т5 (Gas: Argon)
Type of radiation
UV-C
Radiation wavelengths
187nm, 253.7nm

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 13 из 25
Parameter
Value
Radiation intensity
2,100μw/cm2
Mercury Content
0.35mg/kg
Ozone Generation
0.017mg/m³(in 30 minutes in a 3 m³chamber)
Coverage Area
6m²to 9m², 360º
Power
Power: 2.5W
Input Voltage: 5V
Input Current: 0.5A
Frequency: 50/60Hz
Built-in Battery
Type: Lithium-ion
Capacity: 2,000mAh
Charge Time: 4 hours
Discharge Time: 2 hours
Operating Temperature
0°С to +40°С
Operating Humidity
10% to 50% RH (non-condensing)
Storage Temperature
-30°С to +60°С
Storage Humidity
20% to 90% RH (non-condensing)
Timers
Built-in turn-on delay timer (15 seconds)
Built-in operation timer (30 minutes)
Installation
On a horizontal surface
Casing Material
UV Lamp body: ABS Plastic
UV Tube: Quartz glass
Color
White/Black
Dimensions (L хW хH)
50mm x 60mm x 182mm
Casing Protection Class
IP20
Weight
150g (170g with accessories)
Warranty Period
2 years
Service Life
UV Tube: 15,000 hours
Battery: 350 recharge cycles
Certification
CE, EAC, RoHS

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 14 из 25
1.3 Scope of Delivery
The following items and accessories are supplied within the Perenio® Smart Health
UV Mini Indigo package:
1. Portable UV Lamp UV Mini Indigo (1 pc.)
2. USB-MicroUSB cable (0.6m) (1 pc.)
3. Quick Start Guide (1 pc.)
4. Warranty Card (1 pc.)
1
2
Figure 3 –Scope of Supply*
* Images of accessories are provided for informational purposes only
1.4 Packaging and Labelling
The Perenio® Smart Health UV Mini Indigo Portable UV Lamp is supplied in a
carton gift box of 100mm х56mm х232mm (LхWхH) containing the full name and
marking of the device, the list of accessories provided and basic technical
specifications thereof, as well as the date of manufacture and information about the
manufacturing plant of devices.
Weights of the package are as follows:
•Net weight: 150g;
•Gross weight: 200g.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 15 из 25
2. Installation and Setup
Before starting to use the device, it is required to choose one of the possible locations
for the UV Lamp on a horizontal surface. Make sure that the selected room or the
object to be UV irradiated can be tightly closed (windows, doors, covers are tightly
closed).
ATTENTION! Prolonged exposure to UV light can cause painting and fabric
discoloration.
Below see possible locations for Portable UV Lamp:
Figure 4 –Examples of installation*
* Images are provided for informational purposes only

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 16 из 25
2.1 Preconditions for UV Treatment
1. Unpack the UV Mini Indigo Portable UV Lamp and connect it to the power
source using USB-MicroUSB Cable.
NOTE. Any suitable USB Charger (output: 5V/0.5A) can be used to connect to
the mains. Charger is not included in the scope of supply.
2. Wait for the battery to be recharged (This process usually takes no more than
four (4) hours).
NOTE. When battery is fully charged, the LED Indicator of the Power Button will
stop flashing red (See Table 1 above).
3. Disconnect the UV Lamp from the source of power and install it on a flat
horizontal surface in the desired area to be treated by UV and Ozone.
4. Close all windows tightly, turn off the air conditioners, block the air ducts at
the area of exposure.
NOTE. The most effective way to use the UV Lamp in rooms without air circulation
at temperatures from +24°C to +26°С.
2.2 UV Treatment Process
ATTENTION! Carefully read the “Warnings and Restrictions” Section of this
document before turning on the device.
1. Press the Power Button to start the UV treatment process.
NOTE. The UV irradiation process will start 15 seconds after pressing the Power
Button, which allows the User to safely leave the room, or switch off the device
during this period.
ATTENTION! The LED Indicator will be blinking blue during the 15-second
delay period.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 17 из 25
2. Leave the room immediately.
3. The UV Lamp will automatically switch off 30 minutes after the UV treatment
process is started. Switch it on again, if required.
ATTENTION! If the User needs to stop the UV treatment process before the
UV lamp is automatically turned off, they shall wear special eye and skin
protection before entering the room.
4. After turning off the UV lamp, please thoroughly ventilate the room of
UV expose for at least 30 minutes.
ATTENTION! Prevent the presence of people or animals in an unventilated room,
as inhalation of ozone can lead to respiratory damages.
2.2.1 Recommended Exposure Time
The UV treatment period depends on the room type and the area of installation of
the device. See the approximate UV expose time for the UV Mini Indigo Portable
UV Lamp in the table below.
Table 3 –Recommended Exposure Time
Area of Exposure
Recommended Exposure Time
2.5m²max
30 minutes (1 operating cycle)
5m²max
60 minutes (2 operating cycles)
7.5m²max
90 minutes (3 operating cycles)

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 18 из 25
3 Maintenance and Repair
The Perenio® Smart Health UV Mini Indigo Portable UV Lamp does not require
special maintenance in the normal course of operation. However, in order to maintain
the proper state and stable operation of the device the User shall follow the safety
operation rules, warnings, and precautions (See the “Warnings and Restrictions”
Section).
The Perenio® Smart Health Portable UV Lamp repairs shall be carried out in
Service Centers. The UV Tube cannot be repaired due to mercury content.
In the case of warranty repairs or replacement, the User shall provide the Seller with
the sales receipt and the purchased device.
For details on the replacement and repairs of the Perenio® Smart Health Portable
UV Lamp, please contact your local Company representative or the Tech Support
Department at perenio.com.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
©Perenio IoT spol s r.o. All Rights Reserved Doc Version: 1.0.4
Page 19 из 25
4 Warranty Obligations
The warranty period for the Perenio® Smart Health Portable UV Lamp shall be
Twenty-Four (24) months from the date of sale to the End User.
The warranty period for the cable is Six (6) months from the date of sale to the End
User.
ATTENTION! The UV tube and the built-in battery are not covered by the
warranty as they are subject to natural wear and tear and must be replaced from
time to time at a Service Center.
The Manufacturer claims a device service life of 15,000 hours for the UV tube and
350 recharge cycles for the built-in battery.
The Warranty Card shall be deemed valid provided that it is correctly and completely
filled in by the Seller. Upon the purchase, the Customer shall check that both the
Serial Number and the Model name of the device corresponds to those indicated in
the Warranty Card.
Incomplete or illegible Warranty Card shall be deemed not valid. In this case, it is
recommended to contact the Seller and ask for a duly filled Warranty Card. It shall
be also allowed to provide the original of the sales/cashier’s receipt or such other
documentary evidence of the fact and the date of sale of the device. The date of sale
shall be the date indicated on the sales/cashier’s receipt or other relevant document.
If the date of sale is not possible to be determined, the start of the warranty period
shall be the date of manufacture of the device.
The Manufacturer shall guarantee that all materials, components and assemblies of
Perenio® devices are free from defects under normal operation within the warranty
period. The limited warranty shall be applied to the first End Customer of Perenio®
devices only and cannot be transferred to a subsequent customer.
For warranty replacement, the device must be returned to the Seller along with its
receipt. Warranty obligations for Perenio® devices shall be provided in the country
of their purchase only.

Installation and Operation Manual for Perenio®
Portable UV Lamp UV Mini Indigo
Doc Version: 1.0.4 ©Perenio IoT spol s r.o. All Rights Reserved
Page 20 из 25
WARRANTY SERVICE PROCEDURE
In the case of any alleged defect or deficiency of the device detected, the Customer
shall contact the Authorized Service Center before the warranty period expiration and
provide the following:
1. The device with an alleged defect or deficiency.
2. The Warranty Card filled out in accordance with the applicable legal
requirements, or the original of the document confirming the purchase of the
device, including clear indication of the name and the address of the Seller, as
well as the date when this device was sold.
LIMITATION OF LIABILITY
Perenio® devices SHALL NOT BE SUBJECT TO a free warranty service in the case of
identification of at least one of the following damages or defects:
•Any damage caused by force majeure, accidents, and willful or careless acts
(omissions) of the Customer or third parties;
•Any damage caused by the impact of other objects including but not limited to
exposure to moisture, dampness, extreme temperatures or environmental
conditions (or jumps in such conditions), corrosion and oxidation, as well as
penetration of flood and liquid, and the effects of chemicals, animals, insects
and byproducts thereof;
•In the event when the device (accessories and/or components) was unsealed
(the seal integrity was violated), modified or repaired by any party other than
the Authorized Service Center, including repair works using unauthorized spare
parts;
•Any defects or damage caused by improper or unintended use of the device,
including operation contrary to available manuals;
•Any defects caused by natural wear and tear of Products, including bags,
casings, batteries or Installation and Operation Manuals;
•In the event when the Serial Number (Name Plates), the date of manufacture
or the Model name on the device casing was in any way removed, erased,
affected, altered or made illegible;
•In the case of violation of operating procedures and conditions, as well as the
device installation instructions described in relevant Manuals;
•Cracks, scratches and other defects caused as a result of transportation and/or
operation of the device by the Customer or acts of negligence on their part;
•Mechanical damages that occurred after transferal of the device to the
Customer including damage caused by sharp objects, bending, squeezing,
falling, etc.;