Perlick CC24W Series User manual

Installation
& Operation Manual
Wine Column Refrigeration
Model CC24W Series
Model CC24D Series
Form No. Z2487
4.9.2018
Model CC24W-1-4R Shown

Wine Column Refrigeration Installation & Operation Manual
Printed in USA 2
TABLE OF CONTENTS
IMPORTANT!
Read and understand all information in this manual before attempting the installation.
All electrical work must be performed by a qualied technician and
conform to all applicable state and local codes.
GENERAL INFORMATION
Warranty Registration
To register your product, visit our web site at
www.perlick.com. Click on “Commercial”, then
“Resources”, then “Use and Care”, and then
“Warranty Registration Form”. You must complete
and submit this form or the installation date will
revert back to the ship date.
Please record the purchase date and the dealer’s
name, address and telephone number below.
Model Number: ________________________
Serial Number: _________________________
Purchase Date: _______________________
Dealer Name & Address
______________________________________
______________________________________
______________________________________
Phone Number__________________________
SAFETY
PLEASE READ all instructions completely
before attempting to install or operate the unit.
Take particular note of the DANGER, WARNING
an CAUTION information in the manual. The
information is important for the safe and e󰀩cient
installation, operation and care of your Perlick unit.
DANGER
Indicates a hazard that WILL
result in serious injury or
death if precautions are not followed.
WARNING
Indicates a hazard MAY
cause serious injury or
death if precautions are not followed.
CAUTION
Indicates a hazard where
minor injury or product
damage may occur if precautions are not
followed.
Introduction
Congratulations on your purchase of a Perlick
commercial wine column refrigerator. This manual
has been prepared to assist you in the installation
of your column refrigerator and to acquaint you
with its operation and maintenance.
We dedicate considerable time to ensure that our
products provide the highest level of customer
satisfaction. If service is required, your dealer
can provide you with a list of qualied service
agents. For your own protection, never return
merchandise for credit without our approval.
We thank you for selecting a Perlick product
and assure you of our continuing interest in your
satisfaction.
General Information................................................................................................................................. 2
Opening/Niche Dimensions..................................................................................................................... 5
Placement and Alignment of Appliance ................................................................................................. 10
Anti-Tip Bracket ..................................................................................................................................... 11
Installing Door Overlay Panel................................................................................................................ 13
Door Trim Installation............................................................................................................................. 16
Grill Installation...................................................................................................................................... 17
Air Filter Installation............................................................................................................................... 18
PerliQ Digital Control Operation ............................................................................................................ 19
Stainless Steel/Surface Care................................................................................................................. 22
Use and Care Information ..................................................................................................................... 23
Warranty ................................................................................................................................................ 25
NOTE: See page 20 for full warranty details.

Wine Column Refrigeration Installation & Operation Manual
3 Printed in USA
WARNING
Carefully inspect the cabinet
for hidden damage. If damage is discovered, le
your claim immediately with the transportation
company. Perlick is not responsible for damage
in transit.
CAUTION
When moving the unit, be
sure to protect finished flooring with
appropriate material to avoid damage from
moving the appliance.
CAUTION
If unit has been laid on its
back or sides, place unit upright and allow
minimum of 24 hours before connecting the
unit. Failure to do so can a󰀨ect the function
and performance of the appliance.
This appliance should be installed in a dry,
ventilated indoor location. The ambient
temperature of the location must be between
55°F (13°C) and 100°F (43°C) for optimal
performance.
When fully stocked, Perlick wine column refrig-
eration is very heavy. To ensure safety and pre-
vent home damage, the load-bearing capacity
of your oor must be 550 lbs for each CC24W
column being installed.
This product must be installed on a level oor
for safety and optimal performance. The base
must be at to ensure anti-tip brackets properly
function and that the refrigeration system is lev-
el. Any walls and surrounding furniture/xtures
need to be securely attached to the oor, wall
studs or concrete prior to installing the column.
To ensure proper performance, the air intake
(toe kick) must not be blocked. Perlick refrigera-
tion is front-breathing, and covering the intake
will cause the system to overheat and fail.
SITE PREPARATION

Wine Column Refrigeration Installation & Operation Manual
Printed in USA 4
PRIOR TO INSTALLATION
Safety Precautions
WARNING
Inspect the electrical cord
and plug for damage prior
to plugging the unit in.
CAUTION
If service is necessary,
repair work must be
performed by a Perlick authorized servicer.
Work done by unqualied individuals could
potentially be dangerous and will void the
warranty.
CAUTION
If unit has been laid on its
back or sides, place unit
upright and allow minimum of 24 hours before
connecting power. Failure to follow this
procedure may damage the compressor and
void the warranty.
Do not use or store
flammable liquids (ie;
gasoline) or vapors near the appliance.
DANGER
Perlick columns are top
heavy. It is important that it
is secured at all times with the door closed
until installed. Install as directed using anti-tip
brackets provided to prevent tipping.
DANGER
Take special care when
moving to prevent injury.
Electrical
DANGER
Serious electrocution
hazard. Electrical grounding is required. This
appliance is equipped with a 3-prong
(grounding) polarized plug for your protection
against possible shock hazards. Failure to
comply with these electrical guidelines may
result in possible death or serious injury, re
or loss of property.
WARNING
Never use an extension
cord to connect the unit to the electrical
source. Do not use a two-prong adapter or
remove the power cord ground prong.
Installation must comply with all applicable
electrical codes. The electrical supply must be
located within the shaded area of the illustration
below. A separate circuit, servicing only this
appliance, is required. A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation. The outlet should
be placed in the hatched area dimensioned below.
Electrical Supply 115V, 60Hz., Phase 1, 3.3
amps
Service Dedicated 15 amp circuit
Power/Cord Type/
Length
NEMA 5-15P w/5’ power cord
84"
4"
24"
83 11/16"
14 1/8"
66 1/2"
4"
OVERLAY TEMPLATE
DIMENSIONAL LIMIT
21.5/8"
1 4/5"
13 3/8"
22 3/16"
24 1/16"
23 3/4"
28"
90°
50 1/8"
1/2"
3"
3"
10 3/4"
5 1/4"
ELECTRICAL
OUTLET
LOCATION
CABINET
OPENING
DANGER

Wine Column Refrigeration Installation & Operation Manual
5 Printed in USA
INSTALLATION
Installation Tools and Materials
• Screwdrivers (standard Phillips.)
• Power Drill
• Drill bits (masonry bits required for concrete
installation)
• Standard socket, wrench and 1/2” socket
• 2’ and 4’ levels
• Material to protect ooring and surrounding
cabinetry
For Built-In Applications
Opening Dimensions
The depth of each Perlick column is 24” (610) to
door face (not including the 3/4” overlay). Allow for
door panel thickness when planning the nished
opening depth. A minimum of 4” (102) nished
return is required on all sides of the opening. See
below for opening dimensions drawing.
It is important that the side walls of the niche are
plumb prior to installation. The minimum thickness
of both the side walls and the top wall must be
5/8” (16). The minimum thickness of the toe kick
panel must be 1/2” (13). A thickness of 3/4” (19)
is recommended.
Framed cabinets will require additional filler
material behind the face frame for attaching anti-
tip brackets. Refer to the illustration below.
FILLER MATERIAL
FACE

Wine Column Refrigeration Installation & Operation Manual
Printed in USA 6
INSTALLATION CONTINUED
ADJACENT WALL OR STRUCTURE MINIMUM CLEARANCE REQUIREMENTS
WHEN BUILDING INTO STRUCTURE OR NEXT TO ADJACENT WALLS REFERENCE THIS
DRAWING FOR MINIMUM REQUIRED CLEARANCES TO AVOID INTERFERANCE WHEN OPENING
THE DOOR(S).
THE ADJACENT STRUCTURE CLEARANCES INDICATED ARE BASED ON A STANDARD PERLICK
HANDLE INSTALLED ON THE DOOR OVERLAY.
MINIMUM SPACING REQUIRED BETWEEN ADJACENT CABINETS TO AVOID DOOR
SWING INTERFERENCE.
(A) 2 Cabinets HANDLE TO HANDLE.
Refer to (A&B) Opening diagram (page 8) for
nished opening dimensions and outlet locations.
(B) 2 Cabinets HINGE TO HINGE.
Refer to (A&B) Opening diagram (page 8) for
nished opening dimensions and outlet locations.

Wine Column Refrigeration Installation & Operation Manual
7 Printed in USA
INSTALLATION CONTINUED
Opening Dimensions
(C) 2 Cabinets HANDLE TO HINGE.
Refer to (C) Opening diagram (page 8) for
nished opening dimensions and outlet locations.
(D) 3 Cabinets with Hinges either all left or all
right.
Refer to (D) Opening diagram (page 8) for
nished opening dimensions and outlet locations.
(E) 3 Cabinets with Hinges Left-Right-Left or
Right-Left-Right.
Refer to (E) Opening diagram (page 9) for
nished opening dimensions and outlet locations.
(F) 3 Cabinets with Hinges Left-Left-Right or
Right-Right-Left.
Refer to (F) Opening diagram (page 9) for
nished opening dimensions and outlet locations.
MINIMUM SPACING REQUIRED BETWEEN ADJACENT CABINETS TO AVOID DOOR
SWING INTERFERENCE CONTINUED.

Wine Column Refrigeration Installation & Operation Manual
Printed in USA 8
INSTALLATION CONTINUED
(G) 3 Cabinets with Hinges Right-Left-Left or Left-
Right-Right.
Refer to (G) Opening diagram (page 9) for nished
opening dimensions and outlet locations.
FINISHED OPENING DIMENSIONS FOR 2 AND 3 UNIT INSTALLATIONS.
MINIMUM SPACING REQUIRED BETWEEN ADJACENT CABINETS TO AVOID DOOR
SWING INTERFERENCE CONTINUED.

Wine Column Refrigeration Installation & Operation Manual
9 Printed in USA
INSTALLATION CONTINUED
FINISHED OPENING DIMENSIONS FOR 2 AND 3 UNIT INSTALLATIONS
CONTINUED.
Note:
For installations involving more than 3 cabinets, combine opening dimensions for the openings
which correspond to the combined Hinge and Handle congurations.

Wine Column Refrigeration Installation & Operation Manual
Printed in USA 10
PLACEMENT & ALIGNMENT
CAUTION
Before moving the unit
into position, secure the door closed and
protect any nished ooring.
WARNING
If the unit has been on its
back, it must stand upright for a minimum of
24 hours before connecting power.
Move the unit near the opening. Plug the power
cord into the grounded outlet and roll the unit into
position. Push unit into place.
Leveling
Front and rear leveling legs can be adjusted from
the front once the unit is positioned.
NOTE: Remove grill to access leveling adjustment
access holes.
Once the unit is in position, height adjustment
can be made from the front. Using the hex
driver leveling tool, turn clockwise to raise the
unit or counterclockwise to lower. Refer to the
illustration below.
When the unit is properly leveled, door adjustments
are less likely to be necessary.
CAUTION
Level the unit to the oor,
not surrounding cabinetry. This could a󰀨ect
the operation of the unit, such as door closing.
WARNING
To reduce the possibility
of the unit tipping forward, the front leveling
legs must be in contact with the oor.
LEVELING THE UNIT
Adjusting front leveling legs.
Adjusting rear leveling legs.