Phase LHP100GK User manual
1
LHP100GK
2.4GHz Smart Camera
The LHP100GK is a 2.4GHz IR Surveillance Camera which can be installed indoors
or outdoors. The 2.4GHz wire free camera module will transmit audio/video signals
to the host LHK110EK 7” Touch Panel receiver for monitoring and recording
purposes. The host LHK110EK can pair with and control devices such as 2.4GHz IR
cameras, wire free O-net Security devices, and On/Off Plugs. Please see your
LHK110EK Instruction Manual for details.
INTRODUCTION
The LHP100GK features multiple IR LED’s that activate at night (or low light levels)
to ensure a sharper image. The built in microphone transmits sound to the host
LHK110EK. Status LED’s, green and red indicate day or night mode.
OPERATION
1. Status LEDs
1.1 Plug the supplied AC adaptor into an AC socket, and then plug the DC jack into
the IR camera cable. The green LED will illuminate when the power supply is
normal and the camera is in day mode.
1.2 The red LED will illuminate when the light level is low, indicating that the IR
LED’s are active and the camera is in night mode.
OPERATION (Continued)
2. Pairing Button
2.1 The pairing button on the IR camera power input cable is used to pair the camera
with the host LHK110EK.
3. ID Code Learning
3.1 Put the host LHK110EK into the “Pairing” screen for IR Camera (From
“Standby” mode, tap “Setting (Camera)”, select Camera number and IR
Camera, then tap “Pair”).
3.2 Press the Pairing Button on the IR Camera to pair the devices. When pairing is
complete, a “Pairing Successful” screen will appear on the LHK110EK and it
will automatically link to the camera. The user may now switch to the camera
view to confirm if the linking and pairing was successful.
3.3 If “Pairing Failed” appears, please repeat steps 3.1 and 3.2. Note the devices
only remain in pairing mode for 30 seconds. Please see your LHK110EK
Instruction Manual for more information.
4. Video / Audio Functions
Under normal operating conditions, the LHP100GK Camera image can be
viewed from the host LHK110EK or via your smart device. If the LHK110EK
system is triggered by a security device paired on the system (PIR, Magnetic
Contact etc.) the LHP100GK will be activated and begin transmission of video
/ audio signals in H.264 format via 2.4GHz wire free signal to the LHK110EK.
INSTALLATION
1. In order to ensure correct function do not install the camera near a heat source
or where direct sunlight will shine into the camera lens. Avoid high humidity areas
eg. bathrooms or kitchen areas where steam may ‘fog’ the camera lens. Do not
mount the camera on or near metalwork since this can block the camera signals.
2. The camera may be used indoors or outdoors. The camera cable DC jack plug
/ socket is designed to be weather proof. Ensure the DC jack plug / socket is pushed
fully home to avoid moisture ingress.
2
INSTALLATION (Continued)
3. The camera should be installed as shown in Figure 1 below, with the sliding
top cover positioned as shown. The aerial should be pointing upwards.
An installation height of at least 2m is recommended. Use the plugs and screws
supplied to fix the camera to a standard brick wall.
4. Environment: -10°C to 50°C, 20-85% Humidity.
Figure 1
TROUBLESHOOTING
Symptom
Recommendation
Green LED does not
illuminate when the
LHP100GK is powered on.
1. The AC adaptor or the DC jack is not plugged in
correctly.
Transmitted videos are
erratic or unclear. 1. Ensure the 2.4G aerial is correctly fitted and tight.
2. The distance between the camera and host is too
great, reduce the distance.
SPECIFICATIONS
Camera & Audio / Visual Transmissions
Camera Sensor 1/4” CMOS OV7725
Night Vision Range Maximum 15m in low light level (about 1 Lux)
Microphone Built-in
Operating Temperature /
Humidity Range -10°C to 50°C. Maximum 85% relative humidity,
non-condensation
Pixel 640 x 480 VGA
Video Compression H.264
Resolution (with 7” Monitor) 1 to 1: H.264 - 480 x 272 / 30fps
SPECIFICATIONS (Continued)
Camera & Audio / Visual Transmissions
White Balance Automatic
Auto Gain Control (AGC) Automatic
Backlight Compensation Automatic
Signal to Noise Ratio (SNR) > 48 dB
Gamma Compensation 0.45
Electric Shutter Automatic
Lens ViewingAngle Horizontal: 48° / Vertical: 36°
Audio Format One Way, 8K Pulse Code Modulation
IR LED 28 x 850nm
IR CUT Yes
Protection Degree IP65
Mounting Height / Surface Recommended minimum 2m. Standard London brick wall
Power Requirement AC 100-240V / 50-60Hz Adaptor DC5V 1A
RF
Frequency 2.4Ghz
RF Modulation Gaussian frequency-shift keying (GFSK)
Spread Spectrum Frequency hopping
Transmission Range Approximately 100m in free air
Camera numbers Maximum 4 cameras per host LHP100GK
Specifications are subject to change without notice LUXHOMELHP100GK
2015/06
Environmental Concerns:
Please DO NOT dispose of electrical appliances as unsorted waste, use the
recycling facilities provided by your local authorities.
Please DO NOT dispose of packaging as unsorted waste, use the recycling facilities
provided by your local authorities.
