PheeNet WLO-15814N User manual

802.11a/n High Power
Wireless Outdoor
Bridge / AP
WLO-15814N / WLO-15802N
Quick Installation Guide
Ver 1.08

Quick Installation Guide
WLO-15814N / WLO-15802N
Preface
PheeNet IEEE802.11a/n 5GHz 300Mbps MIMO Wireless Outdoor Bridge is a powerful solution. The Wireless Network
Service Provider can use it to build up Wireless Backhaul Point to Point or Point to Multi-point connection, or deploying
last mile services to business or residential broadband subscribers. Network administrators can create multiple subscriber
service tier using per-subscriber rate limiting features, and manage centrally. PheeNet High Power Wireless Outdoor
Bridge/AP utilizes a 200mW output Tx Power connect to the Wireless Mesh Network or WDS infrastructure and provides
the subscriber with an Ethernet connection for a local access.
PheeNet High Power Wireless Outdoor Bridge/AP can be used for different purposes in different modes. In theAP mode,
it can be deployed either as traditional fixed wireless Access Point (AP), or combination of AP and WDS (AP+WDS). In
the WDS mode, it’s only used to expand or bridge Ethernet networks and deployed as a main base, relay based or
remote base station. In the CPE mode, it connects to Wireless Internet Service Provider’s (WISP) outdoor network via
wireless WAN gateway to access to Internet. In the Client Bridge + Universal Repeater mode, it connects to Wireless
Internet Service Provider’s (WISP) outdoor network via wireless or wired bridge to access to Internet
PackageContents
zWLO-15814N / WLO-15802N x 1
zCD-ROM (with User Manual and QIG) x 1
zPSE with AC Cable x 1
zMounting Kit x 1
It is highly recommended to use all the supplies in the package instead of substituting any components by other
suppliers to guarantee best performance.

Quick Installation Guide
WLO-15814N / WLO-15802N
SystemOverview
Front Panel
Rear Panel
1. Reboot Button : Unscrew the screw and click Reset button to restart system or reset to
default configurations.
ÎPress and hold the Reset button for 2 seconds and release to restart system. The LED except Power
indicator will be off before restarting.
ÎPress and hold the Reset button for more than 10 seconds to reset the system to default configurations.
2. Power : Green LED ON indicates power on, and OFF indicates power off.
3. WLAN : Green LED FLASH indicates Wireless Transmit.
4. Ethernet : Green LED ON indicates connection, OFF indicates no connection, FLASH
indicates Packets transmit
5. PoE Connector : For connecting to PSE
6. Dual Ntype connector: to connect to antenna (WLO-15802N only)

Quick Installation Guide
WLO-15814N / WLO-15802N
HardwareInstallation
Please follow the steps mentioned below to install the hardware of WLO-15802N :
¾WLO-15802N
Front Panel Rear Panel
Connect N-type antenna to the N-type connector on the rear panel.
Connect PSE to the PoE connector on the front panel.
Connect an Ethernet cable to the PSE and the other end to a computer.
Power on the PSE in order to supply power to WLO-15802N

Quick Installation Guide
WLO-15814N / WLO-15802N
GettingStarted
WLO-15814N / WLO-15802N supports web-based configuration. Upon the completion of hardware installation, WLO-
15814N / WLO-15802N can be configured through a PC/NB by using its web browser such as Internet Explorer version
6.0.
zDefault IP Address : 192.168.2.254
zDefault IP Netmask : 255.255.255.0
zDefault User Name and Password :
The default user name and password for both root manager account and admin manager account are as follows :
Mode CPE Mode AP Mode WDS Mode Universal Repeater +
Client Bridge Mode
Management Account Root
Account Admin Account Root Account Root Account Root Account
User Name root admin root root root
Password root admin root root root
Step
1. IP Segment Set-up for Administrator's PC/NB
Set the IP segment of the administrator's computer to be in the same range as WLO-15814N / WLO-15802N for
accessing the system. Do not duplicate the IPAddress used here with IPAddress of WLO-15814N / WLO-15802N or
any other device within the network
Example of Segment :
The value for underlined area can be changed as desired; the valid range is 1 ~ 254. However, 254 shall be avoided
as it is already used by WLO-15814N / WLO-15802N; use 10 as an example here.
zIPAddress : 192.168.2.10
zIP Netmask : 255.255.255.0
2. Launch Web Browser
Launch as web browser to access the web management interface of system by entering the default IPAddress,
http://192.168.2.254, in the URL field, and then press Enter.

Quick Installation Guide
WLO-15814N / WLO-15802N
3. System Login
The system manager Login Page then appears.
Enter “root” as User name and “default” as Password, and then click OK to login to the system; the root manager
account is used as an example here.
4. Login Success
System Overview page will appear after successful login.

Quick Installation Guide
WLO-15814N / WLO-15802N
QuickSetup
WLO-15814N / WLO-15802N is a multiple mode system which can be configured either as a gateway or an access point
as desired. This section provides a step-by-step configuration procedure for basic installation for AP Mode, WDS Mode,
CPE Mode and Client Bridge + Universal Repeater.
¾Setup In AP Mode
Step 1 : Mode Confirmation
Ensure the Operating Mode is currently atAP mode; the web management UI can be viewed at the Status section
under the System Overview page.
Step 2 : Change Password
Click System -> Management and then Management Setup page appears.
There can change root and admin manager account. Enter a new password, and verify it again in the New
Password and Check New Password field respectively. Click Save button, and proceed with the following steps.

Quick Installation Guide
WLO-15814N / WLO-15802N
Step 3 : LAN IP Settings
Click System -> LAN, and then LAN Setup page appears.
Enable “Static IP” and “DNS”, and enter the related information in the field marked.
Click Save button to save the settings.
Step 4 : Time Zone settings
Click System -> Time Server, and then Time Server Setup page appears.
Enable “NTP Client”, and then enter the related information.
Click Save button to save the settings.

Quick Installation Guide
WLO-15814N / WLO-15802N
Step 5 : SSID Settings
Click Wireless -> Virtual AP Setup, and then Virtual AP Overview page appears.
Click “Edit” on the PrimaryAP and then Primary AP Setup page appears. Setup the broadcast SSID for easy
identification of the system when device is trying to associate the service. The default SSID is “Main_AP” Click Save
button to save settings
Step 6 : Security Settings
In Primary AP Setup page, select WEP in “Security Type“ drop-down list. The WEP setting field will show up
immediately.

Quick Installation Guide
WLO-15814N / WLO-15802N
Enter the WEP key information required in the WEP settings field, the same information will also be used to set up
devices using WLO-15814N / WLO-15802N's services.
Click Reboot to activate all settings configured above.
Congratulation!
The AP mode is now successfully configured.