Philips Saeco HD8772/47 User manual

Open lid and use handle to remove water tank. To use
without water filter, rinse tank with water. Fill with fresh
water up to MAX mark. Place water tank into machine.
To install water filter see user manual.
NOTE: Only use cool fresh water, any other liquid may
cause damage.
Open coffee bean hopper lid. Slowly pour beans into
hopper. Replace lid.
NOTE: Only use coffee beans. Ground, instant and
flavored coffees may damage the machine.
QUICK START GUIDE
MINUTO CLASS
HD8772/47
SET UP
PLEASE NOTE: OUR MACHINES ARE TESTED WITH
COFFEE AT THE FACTORY TO ENSURE HIGH
QUALITY STANDARDS. WHILE MACHINES ARE
CLEANED THOROUGHLY AFTER TESTING, IN
SOME CASES, COFFEE GROUNDS MAY REMAIN IN
THE MACHINE.
FOR FULL INSTRUCTIONS, PLEASE REFER TO THE
USER MANUAL

1
BEFORE FIRST USE

2
Switch power button on back of machine
to the “I” or ON position.
Turn machine on by pressing “ ” button
on control panel.

2

1
CONTROL PANEL QUICK REFERENCE
For a full understanding of functions, see the user manual.
26. Espresso button
27. Medium coffee button
28. Large coffee button
29. Hot steam/water button
30. “Aroma”- Coffee Strength
button
31. Menu button
32. ON/OFF button
TROUBLE SHOOTING
Q: Why isn’t my coffee coming out hot enough?
A: The beverage temperature setting may be too low. Adjust the beverage
temperature setting to Normal or High.
A: Cups may be cold. Preheat cups with hot water prior to dispensing coffee.
Q: Why is my coffee coming out so weak?
A: The machine automatically adjusts itself after brewing a few cups of coffee to
optimize the extraction of the coffee to the compactness of the ground coffee.
We recommend brewing 3-5 espressos before drinking to allow for this
adjustment process. Refer to the "Saeco Adapting System" in the user
manual for more information.
A: The coffee may be too coarse. Change the coffee blend or adjust the grind.
Finer coffee grounds result in stronger tasting coffee. Refer to the “Adjusting
the ceramic coffee grinder” in the user manual for more information.
Q: Why is my machine leaking water/coffee?
A: Sometimes water is drained automatically by the machine into the drip tray to
manage the rinsing of the circuits and ensure optimum machine performance
A: The dispensing spout may be clogged. Clean the holes in the dispensing spout.
Q: Why isn’t the machine filling up my cup?
A: The machine’s coffee lengths can be programmed. Enter the beverage
programming menu and adjust the coffee length setting to your liking for every
beverage. See "Adjusting the coffee length" section in the user manual.
For more troubleshooting please refer to the User Manual.
NEED ASSISTANCE:
If you have any questions or concerns, we are always available to assist you.
Please call us direct at 1-800-933-7876
or visit us at www.philips.com/saeco
26 29
27 30
28 31
32
Rev.1 - 7.30.13
421944010621

Once machine turns on, it will indicate a priming cycle must be
started.
Place a container under steam wand. Press the “” button to
start the cycle. The machine will start the automatic priming
by dispensing some water through the steam wand. When
the machine stops dispensing, a warm up cycle will begin
automatically.
Once heated, a 1-minute rinse/self-cleaning cycle with fresh water will begin auto-
matically. Place a container under dispensing spout to catch water.
Before using the machine for the first time a manual rinse cycle must be
initialized. Place container under dispensing spout. Select the pre-ground coffee
brewing function by pressing the “” button. Check that the selection lever is set
to “ESPRESSO”. Press the “ ” button. Wait for dispensing to stop. When it has
stopped, repeat this operation 2 more times.
NOTE: Do not add pre ground coffee into the machine during this process.
Place a container under the steam wand and press the “ ” button.
Press the “ ” button to start dispensing hot water through the steam wand.
Do this until the "no water" icon appears in display.
Place a coffee mug under the dispensing spout and adjust it accordingly.
Push the lever to the up position to select the COFFEE
function.
Press the “” button to select your desired aroma or strength. Press the
“ ” button to start brewing.
Remove lower part of the dispensing spout and place a
travel mug underneath it.
Push lever to the up position to select the
COFFEE function.
Press the “” button to select your desired aroma or strength. Press the
“” button to start brewing.
Fill the water tank again up to the MAX level indicator.
Place a cup under dispensing spout and press the “ ” button to grind and
dispense espresso.
Repeat Step 2 three-five times.
Your machine is now ready to brew coffee!

3

4

5

6

1

2

4

3
OPTIMIZE YOUR COFFEE
To optimize coffee extraction to compactness of the ground coffee, brew 3-5 cups of
espresso and discard BEFORE drinking.

1

2

3

1

2

2

7
ESPRESSO
COFFEE
Place an espresso cup under dispensing spout and adjust it accordingly.
Push lever downwards to select ESPRESSO function.
Press the “” button to select your desired aroma or strength. Press
the “” button to start brewing.

3

1

3
COFFEE
BREWING A MEDIUM COFFEE USING WHOLE BEANS
BREWING A LONG COFFEE USING WHOLE BEANS
BREWING AN ESPRESSO USING WHOLE BEANS

1
USING THE AUTOMATIC MILK FROTHER

2
Insert suction tube into automatic milk frother. Push the
automatic milk frother onto the steam wand until it locks
into place.
Plunge suction tube into a milk container. Place a cup under
the automatic milk frother. Press the “”button then
press the “ ”button to start dispensing frothed milk.
Frothed milk will continue to dispense for 3 minutes or
until you press the “” button to stop dispensing.
After each use, clean milk frother as described in the user manual.

3