Philips PCA102CD User manual

PHILIPS CD-ROM Drive
User’s Manual
PCA82CR
PCA102CD

Table of Contents
Chapter 1 INTRODUCTION ..........................1
1.1 Features ...................................1
1.2 Package Contents ...........................2
1.3 System Requirements ........................2
Chapter 2 PRECAUTIONS ...........................3
2.1 During Installation ........................3
2.2 During Operation ...........................3
2.3 During Transport ...........................4
2.4 When Handling a Disc .......................4
2.5 Servicing the Drive ........................4
Chapter 3 INSTALLING YOUR DRIVE .................5
3.1 Installing the CD-ROM Drive ................5
3.2 Letting Your System Recognize the Drive ....8
3.2.1 If You Are a DOS or Windows 3.1 User ...................................8
3.2.2 If You Are a Windows 95 User................................................10
3.2.3 If You Are an OS/2 Warp User................................................13
Chapter 4 USING YOUR CD-ROM DRIVE ...............17
4.1 Drive Applications ........................17
4.2 Front Panel Controls ......................17
Appendix A A MASTER OR A SLAVE DEVICE? ............19
A.1 IDE Connections ...........................19
A.2 Setting Master and Slave Jumpers ..........22
Appendix B SPECIFICATIONS .........................23

i
Copyrights And Liabilities
Copyright  1996 by Philips Electronics N.V. All
rights reserved. No part of this publication may be
reproduced or transmitted in any form by any means
for any purpose without the prior written permission
of Philips Electronics N.V.
The information in this manual is subject to change
without notice and does not represent any commitment
on the part of Philips Electronics N.V. Philips
Electronics N.V. also specifically disclaims any
implied warranties of merchantability or fitness for
any particular purpose.
The software described in this document may be copied
and used by one intended user only, unless otherwise
stated, and the copying should be solely for the
purpose of backup.
In the event the product this manual supports is not
free from defects, the purchaser’s sole remedy shall
be repair or replacement within the warranty period.
By acceptance of this product, you hereby assume all
liability consequent to your use or misuse of it.
Philips Electronics N.V. assumes no liability for
incidental, special or consequential damage of any
kind. Under no circumstances will Philips
Electronics N.V. be liable for any expenses, lost
profits, lost savings, damage to or replacement of
equipment and property, costs of recovering,
reprogramming, or reproducing any data stored in or
used with this product.
Philips and the Philips logo are registered trademarks
of Philips Electronics N.V. All other company names

ii
and product names are trademarks and registered
trademarks of their respective owners.
Printed in
Taiwan

iii
FCC Notice (USA)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment
and receiver.
3. Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced
radio/television technician for help.
Notice 1:
The changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate the equipment.
Notice 2:
Shielded interface cables must be used in order to
comply with the emission limits.

iv
Notice 3:
This product complies with the requirements set out in
the Council Directive on the Approximation of the Laws
of the Member States relating Electromagnetic
Compatibility (89/336/EEC). For the evaluation
regarding the electromagnetic compatibility, the
following standards were applied:
EN 50 082-1, IEC 801-2, IEC 801-3, IEC 801-4
EN 50 081-1, EN 55 022
CDC Regulatory Statement
(Canada)
This digital apparatus does not exceed Class B limits
for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the
Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits
radio-électriques dépassant les limites applicables
aux appareils numériques de la classe B prescrites
dans le Réglement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
D.N.S.F1. Regulatory
Statement
Class 1 laser product
(EN 60825: 1991)
or
Luokan 1 laserlaite

v
Klass 1 laser apparat
(EN 60825: 1991)
Additional remarks:
VAROITUS - Laitteen käyttäminen muulla kuin tässä
käyttöohjeessa mainitulla tavalla saattaa altistaa
käyttäjän turyallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Varning - Om apparaten används pä annat sätt än i
denna bruksanvisning specificerats, kan användaren
utsättas för osynlig lasersträlning, som överskrider
gränsen för laserkläss 1.
According to EN 60825 sub-clause 6, regarding actions
to be taken against dangerous radiation including
copies of all warning labels and information about the
laser components and radiation data such as
wavelength, output power and pluse times.

vi
Important Safety Notice
1. Follow all warnings and instructions marked on the
product.
2. Danger: Invisible laser radiation when open. Avoid
direct exposure to beam.
3. Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
4. Slots and openings in the cabinet and the back or
bottom are provided for ventilation. To protect it
from overheating, these openings must not be
blocked or covered. This product should never be
placed near or over a radiator or heat register, or
in a built-in installation unless proper
ventilation is provided.
5. This product should be operated from the type of
power indicated on the marking label. If you are
not sure of the type of power available, consult
your dealer or local power company.
6. Never push objects of any kind into this product
through cabinet slots as they may touch dangerous
voltage points or short cut parts that could result
in a fire or electric shock. Never spill liquid of
any kind on the product.
Belangrijke
veiligheidsvoorschriften
1. Let op alle waarschuwingen en instructies die op
het product staan vermeld.

vii
2. GEVAAR: Bij het demonteren van dit produkt kunt u
worden blootgesteld aan onzichtbare laserstraling.
Vermijd directe blootstelling aan laserstraling.
3. Trek de stekker van de PC uit het stopcontact
voordat u dit produkt schoonmaakt. Gebruik geen
vloeibaar reinigingsmiddel of spuitbussen. Gebruik
voor het schoonmaken alleen een vochtige doek.
4. De sleuven en openingen in de kast van het produkt
dienen voor de ventilatie. Om te voorkomen dat het
produkt oververhit raakt, mogen deze sleuven en
openingen nooit worden geblokkeerd of bedekt.
Bovendien mag u dit produkt nooit in de buurt van
een radiator of een kachel plaatsen, u mag hem
alleen inbouwen als er voor voldoende ventilatie is
gezorgd.
5. U mag dit apparaat alleen aansluiten op een voeding
van het type dat op het label staat vermeld. Neem
contact op met uw leverancier of het plaatselijk
elektriciteitsbedrijf voor meer informatie.
6. Steek nooit voorwerpen of iets anders in dit
produkt via de ventilatiesleuven of de openingen,
deze voorwerpen kunnen onder spanning komen te
staan of kortsluiting veroorzaken en op die manier
brand veroorzaken of een elektrische schok. Laat
nooit enige vloeistof op of in het apparaat lopen.
Avis important en matière de
sécurité
1. Veuillez observer les avertissements et suivre les
instructions indiquées sur le produit.

vii
i
2. Danger : Cet appareil émet des radiations laser
invisibles lorsqu'il est ouvert. Veillez à éviter
toute exposition directe aux rayons laser.
3. Débranchez votre ordinateur avant de procéder au
nettoyage de l'appareil. N'utilisez pas de produit
liquide ou d'aérosol de nettoyage. Utilisez plutôt
un chiffon propre et humide.
4. Les fentes et les ouvertures situées sur le capot
de l'appareil sont destinées à assurer la
ventilation de ses circuits. Pour protéger
l'appareil de toute surchauffe, il convient de ne
pas obturer ou couvrir ces fentes et ces
ouvertures. En outre, il convient de ne jamais
placer cet appareil sur ou à proximité d'un
radiateur ou d'un accumulateur de chaleur, ou
encore dans une installation intégrée, à moins
qu'une ventilation adéquate soit assurée.
5. Ce produit ne doit fonctionner qu'avec le type
d'alimentation indiqué sur l'étiquette de repérage.
Veuillez consulter votre revendeur ou la société de
distribution électrique locale pour connaître le
type d'alimentation disponible dans votre région.
6. Veillez à ne jamais enfoncer d'objets de quelque
sorte que ce soit dans les fentes ou les ouvertures
de ce produit. Ces objets peuvent en effet entrer
en contact avec des parties dangereuses à haute
tension ou provoquer des coupe-circuits qui, à leur
tour, peuvent entraîner un incendie ou une
électrocution. Veillez également à ne jamais verser
de liquide d'aucune sorte dans l'appareil.
Wichtiger Sicherheitshinweis

ix
1. Befolgen Sie alle auf dem Produkt vorhandenen
Warnungen und Anweisungen.
2. Gefahr: Im geöffneten Zustand kann unsichtbare
Laserstrahlung entweichen. Vermeiden Sie den
direkten Kontakt mit Laserstrahlen.
3. Ziehen Sie den Netzstecker Ihres PC aus der
Steckdose, bevor Sie dieses Produkt reinigen.
Verwenden Sie keine flüssigen Reinigungsmittel oder
Reinigungssprays. Reinigen Sie das Produkt, falls
notwendig, mit einem feuchten Tuch.
4. Die Schlitze und Öffnungen am Gehäuse des Produktes
dienen zur Lüftung. Um das Produkt vor Überhitzung
zu schützen, dürfen die Schlitze und Öffnungen
nicht blockiert oder verdeckt werden. Zusätzlich
sollten Sie dieses Produkt niemals in der Nähe
einer Heizquelle stellen oder in eine Anlage
integrieren, außer wenn ausreichende Lüftung
gewährleistet ist.
5. Dieses Produkt sollte mit der auf dem Etikett
angegebenen Netzspannung betrieben werden. Fragen
Sie Ihren Händler oder Ihr lokales
Stromversorgungsunternehmen, welche Netzspannung
verfügbar ist.
6. Stecken Sie niemals Gegenstände durch die Schlitze
und Öffnungen in das Produkt, da diese Gegenstände
unter gefährlicher Spannung stehende Bereiche
berühren oder Teile kurzschließen und somit Brand
oder elektrischen Schlag verursachen können.
Verschütten Sie keine Flüssigkeiten auf dem
Produkt.

x
Precauzioni Importanti
1. Seguire tutte le istruzioni e precauzioni indicate
sul prodotto.
2. Pericolo! Quando l’unità è aperta, c’è una
radiazione laser invisibile. Evitare l’esposizione
ai raggi laser.
3. Disinserire la spina del PC dalla presa di corrente
prima di effettuare operazioni di pulizia sul
prodotto. Quando lo si vuole pulire, non bisogna
impiegare detergenti liquidi né spray, ma soltanto
un panno umido.
4. Le fessure e aperture presenti sull’unità
permettono la ventilazione necessaria a proteggerla
da surriscaldamento; pertanto queste non devono
essere bloccate né coperte. Inoltre, questo
prodotto non dovrebbe essere mai posto vicino o
sopra termosifoni o altre fonti di calore e neppure
incorporato in altri contenitori a meno che non si
provveda ad una opportuna ventilazione.
5. Questo prodotto dovrebbe esser fatto funzionare con
l’alimentazione elettrica indicata
sull’etichetta.Consultare il proprio rivenditore o
la società elettrica locale per conoscere i tipi di
alimentazione disponbili.
6. Mai introdurre o spingere oggetti di qualsiasi tipo
attraverso le fessure e le aperture poiché
potrebbero entrare in contatto con zone a voltaggio
pericoloso oppure con parti di circuito che possono
provocare incendi o scosse elettriche. Non
rovesciare mai liquidi di alcun tipo sul prodotto.

xi
Importante Advertencia de
Seguridad
1. Tenga en cuenta todas las advertencias e
instrucciones marcadas en el producto.
2. Peligro: Radiación láser invisible al estar
abierto. Evite quedar expuesto directamente a rayos
láser.
3. Desenchufe su PC de la toma de corriente antes de
limpiar este producto. No use detergentes líquidos
o detergentes en pulverizadores. Para limpiar,
sírvase de un trapo húmedo.
4. Las ranuras y aperturas en la cubierta del producto
son aptas para la ventilación. Para prevenir que
el producto se sobrecaliente, estas ranuras y
aperturas no deben ser bloqueadas o tapadas.
Además, este producto no se deberá colocar cerca de
o encima de un radiador o una calefacción, o en una
instalación incorporada, a no ser que venga con una
ventilación apropiada.
5. Este producto tendrá que funcionar con el tipo de
alimentación que se indica en la marca de fábrica.
Recurra a su distribuidor local o compañía
eléctrica para enterarse de los tipos de
alimentación disponibles.
6. No introduzca nunca ningún objeto a través de las
ranuras y aperturas del producto, dado que estos
productos podrán tocar áreas de voltaje peligrosas
y provocar cortocicuitos o choques eléctricos. No
derrame ningún tipo de líquido sobre el producto.

11
Congratulations! You have just made a very important
upgrade for your PC. By installing the PHILIPS 8X or
10X CD-ROM drive into your IBM PC/compatible, you can
now take advantage of the vast host of multimedia
software available today at a higher performance than
ever. Whether you are interested in the Encyclopedia
Britanica, educational games, using your computer as a
digital music studio or composing a business
presentation with sound, graphics and animation, your
new CD-ROM drive will be the tool to efficiently and
effectively get all that information into your
computer.
1.1 Features
This CD-ROM drive has the following key features:
 IDE/ATAPI interface
 Access time at 145 ms for PCA102CD and 155 ms for
PCA82CR
 Data transfer rate at 1,500 KB/sec for PCA102CD
and 1,200 KB/sec for PCA82CR
 Built in 128 KB buffer
 Motorized tray for loading and unloading CDs
 Standard size: fits into a standard 5.25 inch
half-height PC disk drive bay
 Emergency eject for manual disc ejection
 Automatic power-saving feature
 Compatibility with the following disc formats:
Audio-CD, Video-CD, CD-ROM/XA, CD-i/FMV (CD-i
movies), Karaoke-CD, CD Plus and Photo-CD (both
single and multi-session)
INTRODUCTION 1

PHILIPS CD-ROM DRIVE USER’S MANUAL
1
2
 Front-panel Stop/Eject, audio Play/Skip track
control
 Compatibility with Windows 3.1, Windows 95 and
OS/2
Note:
The use of the IDE/ATAPI interface means that you
can use your PC’s existing IDE interface to set
up the drive without the need for an additional
CD-ROM interface card.
1.2 Package Contents
Your complete CD-ROM package contains the following
items:
 CD-ROM drive
 Audio cable
 IDE cable
 software diskette
 Four screws
 This user‘s manual
1.3 System Requirements
 IBM PC or compatible, with 80286 CPU or higher (a
80386 or higher is recommended)
 3.5” floppy drive
 One empty 5.25”
horizontally oriented disk bay
 One free IDE interface connector
 MS-DOS 6.0 or later, Windows 3.1 or higher,
or
OS/2 Warp 3.0 or above

13
Please read this manual thoroughly before installing
or using your new CD-ROM drive.

23
2.1 During Installation
ALWAYS
 install and use the drive in a horizontal
position
PROTECT THE DRIVE FROM:
 high temperature, high humidity, extreme
temperature changes
 dusty area
 excessive vibration
 direct sunlight
 inclined places
2.2 During Operation
ALWAYS
 keep the tray closed to prevent dust and dirt
contamination when not using the drive.
 turn off your PC power before pressing a thin bar
to manually eject the disc tray (see
Chapter 4 )
 use a voltage regulator or Uninterrupted Power
System (UPS) in areas where the power supply
voltage varies a lot
NEVER
 move the drive while it is operating
 operate the drive right after a sudden increase
in temperature
 force the disc tray to open or close by pulling
or pushing it
PRECAUTIONS 2

PHILIPS CD-ROM DRIVE USER’S MANUAL
2
4
 repeatedly open and close the disc tray for no
obvious reasons
 insert any foreign objects into the disc tray
 press hard on the disc tray when it is opened
 expose your PC to random electrical noise
2.3 During Transport
ALWAYS
 remove any disc from the drive before the
transport
 pack the drive in the original packing materials
2.4 When Handling a Disc
ALWAYS
 store a disc in its case to prevent dust
contamination, scratches, bending, and other
damage
 use a clean, soft and dry cloth to remove dust or
fingerprints. Never use fluids like benzene or
anti-static fluids to clean a disc
 handle a disc by its edges
NEVER
 touch the surface of the disc
 write on a disc or place a label on the surface
of the disc
 bend a disc
 place or store a disc in places with high
temperature and humidity or under direct sunlight

15
2.5 Servicing the Drive
ALWAYS
 ask an authorized service technician to perform
any service operations
NEVER
 attempt to open or remove the drive casing by
yourself

35
This chapter contains detailed instructions to guide
you through the installation of your new CD-ROM drive.
To install the drive, your PC must have at least one
free IDE interface connector. If not, you need to go
to a computer retailer and buy an IDE controller card
(an Enhanced IDE controller card is needed if your PC
already has a one-port IDE controller). See
Appendix
A
for a brief introduction to IDE connections.
3.1 Installing the CD-ROM Drive
Here’s how to install your CD-ROM drive:
1. Adjust the Master/Slave jumpers on the back of
the CD-ROM drive as necessary. (The factory
setting of the slave mode meets most people’s
needs and normally does not need to be changed.
See
Appendix A .)
2. Disconnect the power to your PC and remove your
PC's casing.
3. Slide the CD-ROM drive into the mounting rails
of a 5.25” drive bay.
INSTALLING YOUR
DRIVE 3